Beruflich Dokumente
Kultur Dokumente
2.
a)
b)
c)
d)
PAPER II(OCT05)
1. Chematic diagram drawing is
a) location of component are not indicated
b) component are indicated
c) components are located within the system
d) components location in a/c
2. Which material is slightly magnetic & rapidly react with concentrated
nitric acid with greenish blue colour?
a) carbon steel
b) 18-8
c) pure nickel
d) monel
3. Size of flexible hose determined by
a) inside dia in 1/16 increment
b) outside dia in 1/16 increment
c) inside dia in 1/32 increment
d) outside dia in 1/32 increment
4. Fuel lines identified by
a) red colour
b) blue colour
c) green colour
5. Bolt with single raised dash
a) AN corrosion resistant steel
b) AN standard steel
c) Aluminium alloy
6. AN 640 indicates
a) bolt head and shank is drilled
b) bolt with 10/32 dia
c) bolt shank is drilled
7. AN 121110 indicates
a) bolt with 6/8 dia & head is drilled
8. Which washer is used when a bolt is installed at an angle to a surface or
where perfect alignment with surface or where perfect alignment with
surface is required
a) ball socket & seat washer
b) lock washer
c) plain washer
9. Which is used to tighten the Nut & Bolt where torque is critical
a)
b)
c)
d)
precision tool
hox wrench
spanner wrench
torque wrench
10.
Bolt with asterisk mark made of
a) AN corrosion resistant steel
b) AN standard steel
c) Aluminium alloy
11.
a)
b)
c)
d)
12.
AN 170 AD 3-5
a) round head rivet made of 2117 Al alloy
b) universal head rivet made 2117 Al alloy
c) universal head rivet made 2017 alloy
13.
Which packing is effective in both direction in terms of pressure
and back up is
a) O ring
b) W ring
c) V ring
14.
Which chemical treatment converts surface of iron and steel
parts to non metallic coil or absorptive , phosphade
a) parco-lubrizing
b) anodizing
15.
a)
b)
c)
d)
16.
Which process is used to produce hard wear resistant surface or
case cover strong & tough core
a) case hardening
b) tempering
c) normalizing
17.
Mark the correct statement
a) cold water ensure minimum corrosion resistance
25.
What is frequency in 4 pole generator, conductor is turning at
1500 rpm
a) 60 cps
b) 50 cps
c) 120 cps
26.
What is total inductance of three inductors of 2.3.4 henry
a) 1.9 (series)
b) 0.9 (parallel)
27.
In circuit when capacitive reactance is equal to inductive
reactance
a) resonant
b) phase in
28.
a)
b)
c)
d)
29.
With gate open, SCR conducts when applied voltage
a) peak inverse voltage
b) break over voltage
c) cutt off voltage
30.
a)
b)
c)
d)
31.
To prevent generator from motoring
a) reverse current cut out relay
b) voltage regulator
c) circuit breaker
32.
The purpose of equalizing circuit
a) to lower voltage of high generator and raise voltage of low
generator
b) to raise voltage of high generation and lower voltage of low generation
33.
In which line current equal to phase current
a) Delta connected Alternator
b) Star connected Alternator
c) Three phase Alternator
34.
a)
b)
c)
d)
35.
Which ATA code indicate hydraulic power, Fire protection,
pneumatic engine
a) 29, 26, 36, 77
b) 25, 26, 36, 77
c) 29, 28, 36, 77
36.
a)
b)
c)
d)
37.
In oil & chalk process, defect is indicated as:
a) dark gray line with light gray background
b) light gray line with dark gray background
c) white line in green background
38.
In Radiography X ray equipment are graded according:
a) voltage range
b) frequency range
c) ampere range
39.
Which process reveals (surface defects) subsurface defect,
subsurface defect, water in honey comb material:
a) Dye penetrant Process
b) M.P.I.
c) Radiography
40.
Small a/c tied down:
a) alter each flight
b) every height
c) before storm
41.
a)
b)
c)
d)
42.
In swept wing a/c de fueling procedure starts from:
a) outboard wing tank first
b) inboard wing tank first
43.
In pressure fueling:
a) Pressure of fuel pump must be at min. filter pr.
b) Pressure must be correct for refueling system
44.
Bottle jack is used for:
a) single wheel or all wheel of single unit
b) single wheel
c) single brake unit
45.
Which is equivalent to 4 bit:
a) Nibble
b) Byte
c) K.B. (Kilo Byte)
46.
a)
b)
c)
d)
Modem is:
Input/output peripheral
Hardware
Software
Operating system
47.
Which decimal no. is equivalent to (110.001)2
a) 6.25
b) 6.125
c) 6.50
48.
Which is responsible for high lift capacity of Glider:
a) high aspect ratio
b) symmetrical wing
c) Thickness/chord
49.
When tail wheel a/c facing in wind:
a) elevator should be fully up
b) elevator should be fully down
c) elevator should be in neutral position
50.
Angle of attack:
a) Is acute angle between longitudinal axis of a/c & chord of wing
direction.
b) Is horizontal angle between direction wind & plane of symmetry of a/c
c) Is acute angle between chord of airfoil and direction of wind
51.
a)
b)
c)
d)
Aspect ratio:
span/mean chord
span/cross sectional area
chord/span
area/span
52.
Primary control surfaces are:
a) aileron, rudder, elevator
56.
a)
b)
c)
d)
57.
When using hacksaw blade in which direction it gives better
result:
a) forward stroke
b) backward stroke
c) fine
d) coarse
58.
a)
b)
c)
d)
59.
Which is used to mark rivet holes when using original template to
lay out a skin pattern on the new surface is:
a) center punch
b) prick punch
c) transfer punch
60.
Which is used to clean clogged male threaded fastener:
a) die nut
b) tap
c) two part adjustable die
61.
Taper tap is used in tapping procedure during starting the tap
used for starting operation:
a) Taper tap
b) Plug tap
c) Bottoming tap
62.
Which screw driver is used during verneal space limitation:
a) off-set screw driver
b) stubby screw driver
c) simple screw driver
63.
If 1 cm. of main scale is divided in 20 equal part, 24 division of
main scale is equal to 25 division of vernier scale. Least count is:
a) 0.0002 mm.
b) 0.002 cm
c) 0.02 inches
d) 2 cm
64.
Which thread gives/takes great strength/load in one direction:
a) buttress thread
b) square thread
65.
V block is used to:
a) to hold cylindrical object
b) to hold square object
66.
a)
b)
c)
d)
67.
a)
b)
c)
d)
68.
a)
b)
c)
d)
69.
Mark the correct statement:
a) turbo fan engine require lesser runway length for take off than jet
engine.
b) Jet engine, at higher altitude is efficient in comparison with piston
engine
c) Jet engine has more weight to get equivalent power
d) Turbo jet engine requires longer runway.
70.
Modern digital computer consist of:
a) Central processor (CPU) input/output device
b) Hardware
c) Software
71.
Speed of motor increases when load decreases current decrease
because of:
a) frictional loss between motors moving part
b) frictional loss between winding & other parts
c) induced back emf increases
72.
Jo bolt is:
a) externally threaded two piece rivet
b) externally threaded three piece rivet
c) internally thread three piece rivet
73.
For parallel A.C. generators:
a) voltage, phase equal
b) phase, frequency same
c) voltage, frequency phase
74.
Quantity & quality of X-ray depends on:
a) intensity and penetrating power of x-ray
b) frequency & penetrating power
c) frequency & intensity of x-ray
75.
7075-0 indicates:
a) normalizing
b) annealed
c) hardened & tempered
76.
Gasoline having octane no. more than 100 indicated by:
a) octane no.
b) performance no.
77.
Which is used to form rivet head:
a) snap and dolly
80.
a)
b)
c)
d)
2.
3.
In pressure fueling
a) Pressure of fuel pump must be at minimum filter pressure
b) Pressure must be correct for refueling system
4.
5.
6.
7.
8.
9.
10.
a)
b)
c)
d)
weather
non-aromatic fuel
aromatic fuel
naphtha
11.
High-tigue has:
a) chambered fit
b) reamed fit
c) interference fit
12.
13.
14.
15.
16.
17.
18.