Beruflich Dokumente
Kultur Dokumente
LA5744
Monolithic Linear IC
Separately-Excited Step-Down
Switching Regulator
(Variable Type)
http://onsemi.com
Overview
The LA5744 is a separately-excited step-down switching regulator (variable type).
Functions
High efficiency.
Time-base generator (300kHz) incorporated.
Current limiter incorporated.
Thermal shutdown circuit incorporated.
Soft start circuit incorporated.
Specifications
Maximum Ratings at Ta = 25C
Parameter
Input voltage
Maximum output current
SW pin application reverse voltage
Allowable power dissipation
Symbol
Conditions
Ratings
Unit
VIN
30
IO max
VSW
-1
1.75
Pd max1
No heat sink
Pd max2
7.5
Topr
-30 to +125
Storage temperature
Tstg
-40 to +150
Junction temperature
Tj max
150
Operating temperature
76.1114.31.6mm3
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
Symbol
VIN
Conditions
Ratings
Unit
4.5 to 28
LA5744
Electrical Characteristics at Ta = 25C, VO = 5V
Parameter
Symbol
Ratings
Conditions
min
Reference voltage
VOS
Efficiency
Switching frequency
typ
1.20
Unit
max
1.23
1.26
83
300
360
kHz
Line regulation
VOLINE
40
100
mV
Load regulation
VOLOAD
10
30
VO/Ta
240
0.5
mV
mV/C
coefficient
Ripple attenuation factor
RREJ
f = 100 to 120Hz
IS
45
VIN = 15V
dB
3.1
TSD
165
TSD
15
temperature
Thermal shutdown Hysteresis
width
* Design target value : No measurement made.
Package Dimensions
unit : mm (typ)
3343
Pd max -- Ta
4.5
10.4MAX
10.0
1.3
21.7
23.0
15.3
(8.8)
15.0
2.7
3.6
0.9
2.7
1
0.8
(1.6)
8.0
7.5
1001001.5mm3
6.0
5.6
50501.5mm3
4.0
3.3
2.0
1.75
1.7
0.4
4.5
Al heat
sink
mounting
torque
39Ncm
silicone
grease
applied
30301.5mm3
No heat sink
0
-30 -20
10.0
20
40
60
80
100
Ambient temperature, Ta -- C
120
140
160
MSG07021
8.4
SANYO : 220-5HK
Pin Assignment
(1) VIN (2) SWOUT (3) GND (4) VOS (5) SS
No.A0717-2/5
LA5744
Block Diagram
VIN 1
2 SWOUT
Constant
current
circuit
Reg.
OCP
Reset
OSC
Drive
Comp.
TSD
4 VOS
Amp.
ON/OFF Comp.
0.4V
VREF
SS
GND
VIN
SWOUT
LA5744
C2
390F
D1
SBD
C1
470F
/50V
VOS
SS
GND
R2
R1
C3
1F
Notes :
1. C3 is for the soft start function. Delete C3 and keep the SS pin open when the soft start function is not necessary.
2. In some cases, the output may not turn on if power is applied when a load is connected. If this is a problem, increase the value of
the inductor.
No.A0717-3/5
LA5744
Protection Circuit Functional Descriptions
1. Overcurrent protection function
The overcurrent protection function detects, on a cycle-by-cycle basis, the output transistor current and turns off that
output transistor current if it exceeds 3.1A.
Limit current
Inductor current
SWOUT voltage
The VOS pin has the inrush current of 1A (typ). Therefore, the error becomes larger when R1 and R2 resistance
values are large.
2. Startup Delay Function
The output voltage rises when the internal voltage reaches 0.4V (typical). Until that point, a capacitor is charged from
an internal 10A (typical) constant-current supply. The startup delay time can be calculated as shown below
Example : Assume a 1F capacitor is used.
Td =
C V 1F 0.4
=
= 40 ms
i
10A
No.A0717-4/5
LA5744
Timing Chart
VIN voltage
30kHz
300kHz
SWOUT voltage
1.23V
0.8V
VOS voltage
0V
Td
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLCs product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A0717-5/5