Beruflich Dokumente
Kultur Dokumente
PANEL METER
MT4W SERIES
A
Warning
1. In case of using this unit with machinery(Ex: nuclear power control, medical equpment, ship, vehicle, train,
airplane, combustion apparatus, safety device, crime/disaster prevention equipment, etc) which may cause
damages to human life or property, it is required to install fail-safe device.
It may cause a fire, human injury or damage to property.
2. It must be mounted on the Panel.
It may cause electric shock.
3. Do not connect terminals when it is power on.
It may cause electric shock.
4. Do not disassemble and modify this unit. Please contact us if it is required.
It may cause electric shock or a fire.
5. Please check the number of terminal when connect power line or measured input.
It may cause a fire.
Caution
1. This unit shall not be used outdoors.
It might shorten the life cycle of the product or cause electric shock.
Use this product indoors only. Do not use the product outdoors or at locations subject to the temperatures or
humidity outside. (Example : rain, dirty, frost, sunlight, condensation, etc.)
2. When connecting wire, AWG 20(0.50mm) should be used and screw bolt on terminal block with 0.74Nm to
0.90Nm strength.
It may cause malfunction or a fire due to contact failure.
3. Please observe the rated specification.
It might shorten the life cycle of the product and cause a fire.
4. Do not use the load beyond the rated switching capacity of Relay contact.
It may cause insulation failure, contact melt, contact failure, relay broken, fire etc.
5. In cleaning the unit, do not use water or organic solvent. And use dry cloth.
It might cause an electric shock or fire that will result in damage to the product.
6. Do not use this unit at place where there are flammable or explosive gas, humidity, direct ray the sun,
radiant heat, vibration, impact etc.
It may cause explosion.
7. Do not inflow dust or wire dregs into inside of this unit.
It may cause a fire or mechanical trouble.
8. Please connect properly after checking the polarity of measurement terminals.
It may cause a fire or explosion.
45
Min. 52.0
92
(Unit:mm)
<Option>
MT4W-DV-
250mV/50mV
5V/1V
50V/10V
500V/100V
COM
HOLD/
ZERO
MT4W-DA2
5mA/2mA
50mA/4-20mA
500mA/200mA
5A/2A
COM
HOLD/
ZERO
2V/1V
20V/10V
110V/50V
500V/250V
COM
MT4W-AA1
100mA/50mA
500mA/250mA
1A
5A/2.5A
MAIN OUT
CONTACT OUT:250VAC 3A 1a
RESISTIVE LOAD
+ SOURCE
12-24VDC 5W
100-240VAC
50/60Hz 5VA
MT4W-AV1
HOLD/
ZERO
COM
4
6 8
+24VDC
GO 30mA Max.
COM1 HI LO
1
4
6 8
+24VDC
30mA Max.
COM1 HI LO
1
11 13 15 17 19
6 8 10 12 14 16 18 20
+24VDC
GO
30mA Max.
DC4-20mA
Load 600 Max.
COM1 HI LO
0V
1
13
14
15
LO
- 4]
Main Out
(NPN Open
Collector)
12-24VDC
Max. 50mA
6 8 10 12 14 16 18 20
POL CLOCK LATCH
+24VDC
30mA Max.
SERIAL OUT
(NPN OPEN COLLECTOR)
12-24VDC Max. 50mA
0V
7
COM2 DATA
11 13 15 17 19
COM1 HI LO
1 3
5
- 8]
0V
7
6 8 10 12 14 16 18 20
+24VDC
B D D1 D3 DOT COM2
30mA Max.
BCD OUT
(NPN OPEN COLLECTOR)
12-24VDC Max. 50mA
COM1 HI LO
0V A C D0 D2
POL
1 3
5 7
9 11 13 15 17 19
Main Out
(PNP Open
Collector)
12-24VDC
Max. 50mA
- 9]
6 8 10 12 14 16 18 20
+24VDC B(-) SG
30mA Max.
RS485
COM1 HI LO
3
Main Out
(PNP Open
Collector)
12-24VDC
Max. 50mA
0V A(+) SG
5
11 13 15 17 19
Digit signal
Output data
tb
31.2ms
Digit
signal
D3
D2
D1
D0
A
B
Data
signal
C
D
dot
Display
*tw
Latch
*ta
Clock
Cn-1
Data
Cn
C1
Dn-1
Dn
D1`
Data 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Output DP D C B A DP D C B A DP D C B A DP D C B A
Clock
L
H
H
H
H
H
L
H
H
Data H H L H H H H H L L L H H L H H H H H L
H
tw
*ta
tb
Latch
H
H
Display
This function is to display setting(-1999 to 9999) of particular High/Low-limit value in order to display High/Low-limit
value of measured input.
If measured inputs are 'a' or 'b' and particular values are 'A' or 'B', it will display a=A, b=B as below graph.
Display
value B
Display
value B
A
a
b
Input value
b
Input value
Display
value B
b
Input value
Display
value
A
a
b
Input value
A
B
Input value
Display
value A
B
b
Input value
Display Description
HHHH
D-HH
D-LL
F-HH
OVER
Display range
-1999 to 9999
-199.9 to 999.9
-19.99 to 99.99
-1.999 to 9.999
DOT
0
)0
)00
)000
Initialization function
The above specifications are subject to change and some models may be discontinued without notice.
PA 1
(Parameter 1)
RUN
Press
Current output(DC4-20mA)
Scale adjustment function
[PA 2 : FS-H/ FS-L]
Diplay value
FS-H
INIT
NO
Input bias
INbE exponent
OUtT Out type
HYS Hysteresis
Startup compen
PA 2
(Parameter 2)
LhST
HI
GO
LO
MT4W-DA/AA
AC frequency measurement
function [PA1 : DISP]
(Picture 1)
Y
time
time
Y
0
15.000
12.000
9.000
6.000
(Example of gradient
correction)
Indication
value for
measured
input Input
value
3.000
1.000
X
Input value
Setting method
H-SC
Unavailable
7.500
5.000
3.750
3.000
INbH
1.000
2.000
3.000
4.000
5.000
Note
In this case, any
setting methods
display the same
display value.
HhST
HI
GO
LO
LlST
HI
GO
LO
LdST
GO
LO
H
H
H
H
H
PA 0
(Parameter 0)
Parameter setting
Parameter 0
key 3 sec.
key
RUN
key touch
hSET
lSET
hPEK
lPEK
Parameter 1
RUN
Item
key for 3 sec.
MT4W-DV 500V
PA1
MT4W-DA 5A
100V
2A
MT4W-AV 500V
50V
)5A
10V
)2A
110P()
250V
5V
50MA
1V
)25V
4-20
50MV
5MA
50V
20V
10V
)25A
)1A
50MA
2MA
2V
1V
500V
5A
500V
IN-R
DISP
IN-T
STND
It shows max.display
value of standard
specification.
Display value is fixed.
MT4W-AA 5A
@5A
1A
)5A
5A
DOT (Refer to
500V
No output
Flash twice
in order and
it returns to
5A RUN mode.
MT4W-DV/AV
HI
GO
H: Hysterisis
hST
Operation
YES
GO
LO
lST
Note
Available AC type only.
Setting range: STND, SCAL, FREQ
Display Max. display value of STND
Available AC type only.
OFF
DOT Dot
Function
Selectable RMS/AVG in AC type
Selection of input range
Selection of display type
Standard scale range
Frequency display
Scale range
Set max. value of display range
Set min. value of display range
YES
Output operation
Input type
Input range
Display
Standard
Frequency
Scale
High scale
Low scale
Mode
IN-T
IN-R
DISP
STND
FREQ
SCAL
H-SC
L-SC
0.0 to 500.0
0.0 to 100.0
0 to 50.00
0.00 to 10.00
0.00 to 5.000
0.000 to 1.000
0.00 to 250.00
0.00 to 50.00
0.000 to 5.000
0.000 to 2.000
0.0 to 500.0
0.00 to 200.0
0.00 to 50.00
00.00 to 20.00
0.000 to 5.000
0.000 to 2.000
0.0 to 500.0
0.0 to 250.0
0.0 to 440.0
0.00 to 50.00
0.00 to 20.00
0.00 to 10.00
0.000 to 2.000
0.000 to 1.000
0.000 to 5.000
0.000 to 2.500
0.000 to 1.000
0.0 to 500.0
0.00 to 250.0
0.00 to 100.0
0.00 to 50.0
hSET
lSET
4.33315M
4.33315M
433.15k
433.15k
43.15k
43.15k
2.15k
2.15k
0.01
0.01
0.1
0.1
1.0
1.0
10.0
10.0
4.987M
4.987M
1.087M
1.087M
200k
200k
20k
20k
0.01
0.01
0.05
0.1
0.1
0.5
0.5
t : 20ms
ta : 0.05ms
tw : 5ms
tb : 4.95ms
*tb
Parameter
Parameter Display
Data
t
- 3]
GO
- 5]
- 7]
Main Out
(PNP Open
Collector)
12-24VDC
Max. 50mA
COM2 DATA
11 13 15 17 19
AC
current
4mA
6 8 10 12 14 16 18 20
POL CLOCK LATCH
+24VDC
30mA Max.
SERIAL OUT
(NPN OPEN COLLECTOR)
12-24VDC Max. 50mA
GO
- 6]
Main Out
(NPN Open
Collector)
12-24VDC
Max. 50mA
Main Out
(PNP Open
Collector)
12-24VDC
Max. 50mA
11 13 15 17 19
12
GO
COM1 HI LO
Main Out
(NPN Open
Collector)
12-24VDC
Max. 50mA
mA
- 1]
11
GO
Main Out
(NPN Open
Collector)
12-24VDC
Max. 50mA
RS485
9
COM
- 2]
AC
voltage
Input impedance
15
8 10 12 14 16 18 20
+24VDC
30mA Max.
DC4-20mA
Load 600 Max.
COM1 HI LO
0V
1 3
5 7
9 11 13 15 17 19
11 13 15 17 19
10 12 14 16 18 20
B(-) SG
LO
+ SOURCE
12-24VDC 5W
100-240VAC
50/60Hz 5VA
0V A(+) SG
5
GO
14
GO
GO
HI
- 0]
DC4-20mA
Load 600 Max.
10 12 14 16 18 20
B D D1 D3 DOT COM2
BCD OUT
(NPN OPEN COLLECTOR)
12-24VDC Max. 50mA
A C D0 D2
POL
0V
5
13
HI
12
10
+ HOLD/
SOURCE
ZERO
12-24VDC 5W
100-240VAC
50/60Hz 5VA
11
DC
current
Measured input
and range
0-500V [500V]
0-100V [100V]
0-50V [50V]
0-10V [10V]
0-5V [5V]
0-1V [1V]
0-250mV [)25V]
0-50mV [50Mv]
0-5A [5A]
0-2A [2A]
0-500mA [)5A]
0-200mA [)2A]
0-50mA [50MA]
4-20mA [4-20]
0-5mA [5MA]
0-2mA [2MA]
0-500V [500V]
0-250V [250V]
0-110V [110P]
0-50V [50V]
0-20V [20V]
0-10V [10V]
0-2V [2V]
0-1V [1V]
0-5A [5A]
0-2.5A [@5A]
0-1A [1A]
0-500mA [)5A]
0-250mA [)25A]
0-100mA [)1A]
0-50mA [50MA]
In some applications the measured input may fluctuate which in turn causes the display to fluctuate. By adjusting the
display cycle delay function time at DIS.T of parameter 2, the operator can adjust the display time within a range of 0.1
sec to 5 sec. For example, if the operator sets the display cycle time to 4.0 sec., the display value displayed will be
the average input value over 4 sec. and also will show any changes if any every 4 sec.
+ -
10
Relay output[MT4W-
SOURCE
12-24VDC 5W
100-240VAC
50/60Hz 5VA
DC
voltage
+0.8
-0
Terminal connection
Type
Min. 116
+0.6
-0
This time function limits the operation of an output until the measured input(overvoltage or inrush current) is stable at
moment of power on. All outputs are off during startup compensation time setting after power is supplied.
Setting range: 00.0 to 99.9 (Unit: sec.), Factory default: 00.0
Panel cut-out
1
2
3
MT4W-4
MT4W-1
100-240VAC 50/60Hz
12-24VDC
90 to 110%
5VA
5W
7Segment LED display (red) (Character height: 14.2mm)
235 - DC Type: F.S.0.1% rdg2digit / AC Type: F.S.0.3% rdg3digit
Display accuracy
DC/AC Type: F.S.+0.3% rdg +3digit max. only for 5A terminal
-10 to 50 - DC/AC Type: F.S.0.5% rdg3digit
Input
DC Voltage/Current, AC Voltage/Current, AC Frequency
Max. allowable input 110% for each measured input range
A/D conversion method Practical over sampling using successive approximation ADC.
Sampling cycle
DC type: 50ms, AC type: 16.6ms
Max. indication range -1999 to 9999(4digit)
Relay output - Contact capacity: 250VAC 3A, 30VDC 3A/Contact composition: N.O(1a)
Preset output
NPN/PNP Open Collector output - 12-24VDC 2V 50mA Max.(Load resistance)
RS485 communication output - Baud rate:1200/2400/4800/9600, Communication method : 2-wire half duplex,
Sub output
Synchronous method: Asynchronous method , Protocol : Modbus type
(Transmission output) Serial/BCD output - NPN Open collector output, 12-24VDC Max. 50mA(Resistive load)
DC4-20mA output - Resolution: 12,000 division(Load resistance max. 600), Response time:Max. 450ms
Insulation resistance
Min. 100M (at 500VDC megger) between external terminal and case
Dielectric stength
2,000VAC for 1minute between external terminal and case
Noise stength
2kV the square wave noise (pulse width: 1) by the noise simulator
Mechanical
0.75mm amplitude at frequency of 10 to 55Hz (for 1 min.) in each X, Y, Z direction for 2 hours
Vibration
Malfunction
0.5mm amplitude at frequency of 10 to 55Hz (for 1 min.) in each X, Y, Z direction for 10 min.
Mechanical
100m/s (approx. 10G) in each X, Y, Z direction for 3 times
Shock
Malfunction
300m/s (approx. 30G) in each X, Y, Z direction for 3 times
Mechanical
Min. 20,000,000 operations
Relay
life cycle Malfunction
Min. 100,000 operations (250VAC 3A Load current)
Ambient
-10 to 50, Storage: -20 to 60
Environ temperature
-ment
Ambient
35 to 85%RH, Storage: 35 to 85%RH
humidity
Double insulation or reinforced insulation
Insulation type
(Mark: , dielectric strength between the measuring input part and the power part: 1kV)
Approval
1
Weight
Approx. 326g(Approx. 211g )
1: The weight with packaging and the weight in parentheses is only unit weight.
Environment resistance is rated at no freezing or condensation.
Diplay value
Model
Power supply
Allowable voltage range
Power consumption
Display method
hSETis displayed according to the setting of output operation mode, when user sets "OFF", hSET/lSETare not displayed.
Parameter 2
RUN
key 5 sec.
OUtT Setting range: OFF, lST, hST, LhST, HhST, LlST, LdST
Preset output mode"
Press one
Setting
The saved
value
setting value
flashes evey
0.5 sec.
250V
IN-R
Press one
250V
125V
DISP
5. When confitming the setting value with
key, the changed setting value flashes twice
and enters into the next setting.
6. It returns RUN mode from parameter by
pressing
key for 3 sec.
2. When pressing
key in each parameter,
the initial mode of the parameter is displayed.
(Refer to the description of each parameter.)
IN-R
FS-H
Ex)
EVIN
DIsT
PA 2
Refer to "
Major product
Photoelectric Sensors
Temperature Controllers
Fiber Optic Sensors
Temperature/Humidity Transducers
Door Sensors
SSR/Power Controllers
Door Side Sensors
Counters
Area Sensors
Timers
Proximity Sensors
Panel Meters
Pressure Sensors
Tachometer/Pulse (Rate) Meters
Rotary Encoders
Display Units
Connector/Sockets
Sensor Controllers
Switching Mode Power Supplies
Control Switches/Lamps/Buzzers
I/O Terminal Blocks & Cables
Stepper Motors/Drivers/Motion Controllers
Graphic/Logic Panels
Field Network Devices
Laser Marking System (Fiber, Co, Nd: Yag)
Laser Welding/Cutting System
http: //www.autonics.com
Trusted Partner In Industrial Automation
HEADQUARTERS:
18, Bansong-ro 513beon-gil, Haeundae-gu, Busan, South Korea,
48002
OVERSEAS SALES:
#402-404, Bucheon Techno Park, 655, Pyeongcheon-ro,
Wonmi-gu, Bucheon, Gyeonggi-do, South Korea, 14502
TEL: 82-32-610-2730 / FAX: 82-32-329-0728
E-mail: sales@autonics.com
EP-KE-77-0009L