Beruflich Dokumente
Kultur Dokumente
iii)
(a) Writing device (b) Drawing device (c) Locating device (d) Lighting device
Color raster display uses three electron guns. namely:
(a)Red. green and blue (b) Red, green and yellow
Q
Q
iv)
v)
(c) White, blue and black (d) Red, black and white
Write Full form of CAD, CAM, CAE, CAQC, CAPP, CIM
------ is an image generation technique:
a)
b)
a)
6
4
6
b)
computer graphics
Write note on Homogeneous coordinates
b.G33
c. G44
d.
G01.
2 D0 loop-
a. G24
b. G25
c.G22
d.
G23
3 Tool change-
a.M04
b.M06
c.M05
d.
c.M05
d.
M08
4 Spindle anticlockwise and coolant on
a.M14
b.M16
5 G. Tool change.
a.M04
c.M21
d.M13
b.M06
B.
A. The device used to read the NC systems is called______
a) Scanner
b) Punch tape
c) Flexowriter
reader
d) Collator
b) Hard
c) Fixed automation
automation
d) Rigid
automation
C. In CNC programming, the codes for angular dimensions around x,y,z axes
are___
a) A,B,C
c) I,J,K
b) U,V,W
d) L,M,N
b) Ease of
handling the
job
d) All of these
b) two
c) three
d) four
a) details on tools, operation sequence and processes. Assume suitable data and
Mention clearly.
a)
b) Elaborate the importance of tool magazine and ATC
6
4
8
d)
Absolute and
incremental
b) Canned cycles
e)
programming
DNC
c) Modular tooling
f)
Punch-tape and
tape reader
10M
B.D0 loop-
a. G24
c.G22
a. G17
d. G23
b.G04
d.G18
Check.
a. G27
E. Inch Programming.
b.G13
a.G70
d.G72
b.M01
c.M02
d.M04
a.M04
b.M06
c.M05
d. M08
coolant on
a.M14
b.M16
c.M21
b.G84
c.G91
d.G90
b.M31
c.M27
d.M32.
7M
Fig-2
B.
b.G71
c.G69
J. End of Tape -
A.
d.G26
G. Tool change.
I. Absolute positioning
a.M30
c.G20
F. End of program
a.M00
a.G18
b. G25
Write the CNC part program for the component given fig-2.
8M
Fig-2
d.M13\
4
5
8
4
4
MCQ
Tablet Pen is
a Display
b Output
an____device
devices
a Modification of
needed for___
c Input
d All of
above
Optimization of design
design
)
Q.
c)
)
b
)
1 Hardware in CAD
)
2 Homogeneous coordinate
a.M14
b.M16
c.M21
d.M13
5 G. Tool change.
a.M04
b.M06
c.M05
d. M08
Q.1B. Following questions carry 1 mark each
A. The device used to read the NC systems is called______
e) Scanner
f) Punch tape reader
g) Flexowriter
h) Collator
B. Flexible Automation is also called as___
e) Soft automation
f) Hard automation
g) Fixed automation
h) Rigid automation
C. In CNC programming, the codes for angular dimensions around x,y,z axes are___
e) A,B,C
f) U,V,W
g) I,J,K
h) L,M,N
D. Multiple pallets are used in CNC machine tools, basically for____
e) Increasing the cost of machine
f) Ease of handling the job
g) Increasing machine utilization
h) All of these
E. The miscellaneous function words consist of _____ digits
e) one
f) two
g) three
h) four
Q.2 a) Write the CNC part program for the component given fig-2. Provide the details on tools,
operation sequence and processes. Assume suitable data and Mention clearly.
Q.3 a)
b)
Q.4 a)
b)
Q.5
a)
b)
c)
6
4
6
4
8
All Questions asked in Nov 2009/May 2010/Nov2010/May 2011/Nov 2011/May 2012/Nov 2012/May
2013/Nov2013 Given most probable questions and MCQs