Sie sind auf Seite 1von 4

In a tubular heat exchanger with two shell passes and eight tube passes, 100000 of

water are heated in the shell from 180 to 300. Hot exhaust gases having roughly the
same physical properties as air enter the tubes at 650 and leave at 350. The total
surface, based on the outer tube surface, is 10000. Determine (a) the long-mean
temperature if the heat exchanger were a simple counterflow type, (b) the
correction factor F for the actual arrangement, (c) the effectiveness of the heat
exchanger, (d) the over-all heat-transfer coefficient.

In a single- pass counterflow heat exchanger, 10000 of water enter at 60 and cool
20000 of an oil having a specific heat of o,50 from 200 to 150. If the over-all heattransfer coefficient is 50, determine the surface are required.

Determine the outlet temperature of the oil in Pro. 11-6 for the same initial
temperatures of the fluids if the flow arrangements is one shell pass and two tube
passes, but with the same total area and average over-all heat-transfer coefficient
as the unit in Prob. 11-6

An economizer is to be purchased for a power plant. The unit is to be large enough


to heat 60000 of water from 160 to 360. There are 100000 of flue gases (cp)
available at 800. Estimate (a) the outlet temperature of the flue gases (b) the heattransfer area required for a counterflow arrangement if the over-all heat-transfer
coefficient is

Water is heated while flowing through a pipe by steam condensing on the outside of
the pipe. (a) Assuming a uniform over-all conductance along the pipe, derive an
expression for the water temperature as a function of distance from the entrance.
(b) For an over-all conductance of 100, based on the inside diameter of 2 in, a
steam temperature of 220, and a water-flow rate of 500, calculate the length
required to raise the water temperature from 60 to 150.

At a rate of 5.43 gpm, water at 80 enters a No. 18 BWG8% in. condenser tube made
of nickel chromium steel (k). The tube is 10 long and its outside is heated by steam
condensing at 120 F. Under these conditions the average heat-transfer coefficient
on the steam side may be taken as 2000. On the interior of the tube, however, there
is a scale having a thermal conductance equivalent to 1000. (a) Calculate the over-

hall heat-transfer coefficient U per square foot of exterior surface area, (b) Calculate
the exit temperature of the water.

Dry air is cooled from 150 to 100, while flowing at the rate of 10000 in a simple
adiabatic counterflow heat exchanger, by means of cold air which enters at 60 and
flows at a rate of 12500. It is planned to lengthen the heat exchanger so that
100000 of air can be cooled from 150 to 80 with a counterflow current of air at
12500 entering at 60. Assuming that the specific heat of the air is constant,
calculate the ratio of the length of the new heat exchanger to the length of the
original

Water flowing at a rate of 100000 is to be cooled from 200 to 150 by means of an


equal flow rate of cold water entering at 100. The water velocity will be such that
the over-all coefficient of heat transfer U is 400 .Calculate the square feet of heatexchanger surface needed for each of the following arrangements: (a) parallel flow
(b) counterflow (c) a multi-pass heat exchanger with the hot water making one
pass through a well-baffled shell and the cold water making two passes through the
tubes, and (d) a crossflow heat exchanger with the hot water making one pass
through the shell and the cold water making one pass through the tubes.

A steam-heated single-pass tubular preheater is designed to raise 45000 of air


from 70 to 170, using saturated steam at 20 psi. It is proposed to double the flow
rate of air and, in order to be able to use the same heat exchanger and achieve the
desired temperature rise, it is proposed to increase the steam pressure. Calculate
the steam pressure necessary for the new conditions and comment on the design
characteristics of the new arrangement.

En un intercambiador de calor tubular con dos pasadas de shell y pasa de ocho tubos,10
0000 de agua se calientan en el shell de 180 a 300. Calientes de escape gases queteng
an aproximadamente las mismas propiedades fsicas como aire entre los tubos de650 y
dejar en 350. La superficie total, basado en la superficie externa del tubo, es10000. Det
erminar (a) la temperatura media de largo si el intercambiador de caloreran un tipo de c
ontracorriente simple, (b) el factor de correccin F para el arregloreal, (c) la efectividad
del intercambiador de calor, (d) el coeficiente total detransferencia de calor.

En un intercambiador de calor contracorriente de una


sola pasada, 10000 de aguaentra a los 60
aos y enfriar 20000 de un aceite con un calor especfico de o,
50 de200 a 150. Si el coeficiente de transferencia de calor total es 50, determinar lasup
erficie requerida.
Determinar la temperatura de salida del aceite en Pro. 11-6 para las mismastemperatur
as iniciales de los lquidos si el rgimen de flujo es una cscara pase y dospases de tubo
, pero con la misma rea total y el coeficiente promedio total-transferencia de calor com
o la unidad en Prob. 11-6
Un economizador es comprarse una planta de energa. La unidad debe ser lo
suficientemente grande para calor 60000 de agua de 160 a 360. Hay 100000 de losgas
es de combustin (cp) en 800. Estimado (a) la temperatura de salida de la zona degase
s (b) la transferencia de calor de tubo requerido para un arreglo decontracorriente si el c
oeficiente de transferencia de calor total es

Agua se calienta mientras que fluye a


travs de una tubera de vapor condensacinsobre el exterior de la tubera. (a) suponie
ndo una conductancia total uniforme a lo
largo de la tubera, derive una expresin para la temperatura del agua en funcin dela d
istancia de la entrada. (b) para la conductancia de un total de 100, basado en elinterior
de 2 de dimetro, una temperatura de vapor de 220 y un caudal de agua de500, calcula
r la longitud necesaria para elevar la temperatura del agua de 60 a 150.

A una tasa de 5.43 gpm, agua en 80 entra un BWG8 nm. 18% pulg condensadortubo d
e acero al cromo nquel (k). El tubo es de 10 largos y su exterior es calentadopor el vapo
r de condensacin a 120 F. Bajo estas condiciones, el coeficiente promediode transferen
cia de calor en el lado de vapor puede tomarse como 2000. En el interiordel tubo, sin
embargo, existe una escala con una conductancia trmica equivalente a1000. (a) calcul
ar el coeficiente de transferencia de calor excesiva
hall U por piecuadrado de superficie exterior, (b) calcular la temperatura de salida del a
gua.
El aire seco se enfra desde 150 a 100, mientras que
fluye a una velocidad de 10000 enun intercambiador de calor de contraflujo adiabtico
simple, por medio de aire froque entra a los 60

aos y fluye a una velocidad de 12500. Se planea alargar elintercambiador de calor que
puede refrigerarse 100000 de aire de 150 a 80 con unacorriente de contracorriente de a
ire en 12500 entrando a los 60
aos. Suponiendoque el calor especfico del aire es constante, calcular el cociente de la
longitud delnuevo intercambiador a la longitud de la original

Agua que fluye a una velocidad de 100000 debe refrigerarse de 200 a 150 por
mediode un caudal igual de agua fra a 100. La velocidad del agua ser tal que el coefici
entetotal de transferencia de calor U es 400. Calcular los pies cuadrados de intercambia
dorde calor de superficie necesaria para cada
una de las siguientes disposiciones: (a)contraflujo (b) flujo en paralelo (c) un intercambi
ador de calor de paso mltiples conla agua caliente haciendo un paso a
travs de una concha bien desconcertado y elagua fra haciendo dos pasa a
travs de los tubos y haciendo un paso a
travs de lostubos de agua (d) un intercambiador de calor de flujo
cruzado con el agua calientehaciendo un paso a travs de la cscara y el fro.
Un precalentador tubular de una sola
pasada calentada al vapor est diseado paralevantar 45000 de aire de 70 a 170, medi
ante vapor saturado a 20 psi. Se proponeduplicar el caudal de aire y, con
el fin de poder utilizar el mismo intercambiador decalor y lograr el aumento de
la temperatura deseada, se propone aumentar la presinde vapor. Calcular la presin de
l vapor necesaria para las nuevas condiciones ycomentar las caractersticas de diseo d
e la nueva disposicin.

Das könnte Ihnen auch gefallen