Beruflich Dokumente
Kultur Dokumente
SPRINGBACK EFFECT ON
PERFORATED SHEET METAL
GUIDE:
Prof. G.Venkatachalam
TEAM MEMBERS:
Ashish Devarth (08BME037)
Bhupendra Singh (08BME055)
Ravi Shekhar (08BME181)
Introduction
The elastic strain recovery in the formed part after deformation is called
springback effect.
Springback is the increase in included angle of the formed part relative
to the included angle of the forming tool after the tool is removed.
With the knowledge of springback, tool dimensions, die design, force
and punch motion can be modified to produce the products with
required dimensions.
Perforated sheet metal is made through sheet metal stamping and sheet
metal manufacturing process.
Contd..
Literature Review
Cho et.al studied the effect of punch corner radius, the punch-die
clearance and friction coefficient on Springback effect.
Chan studied spring-back angles of the work piece by varying the punch
angle, punch radius and die-lip radius.
Panthi et.al studied the effect of material properties (yield stress, Youngs
modulus, strain hardening) and geometric parameters (thickness of sheet,
die radius, sector angle) on springback effect at minimal load condition.
Lia et.al studied the materials hardening model and its affect on the
accuracy of springback calculation.
Chakrabartty et.al studied the elastic/plastic analysis of the sheet bending
process under conditions of plane strain.
Contd..
Romen et. al studied that the spring back's increasing classical trends are
related to radius decrease, yielding stress increase, bending radius increase
and Youngs modulus decrease.
Tan et.al studied that due to the non-homogeneous plastic deformation
across thickness, springback will result in redistribution of internal stress
and residual stress can be observed in a bent specimen.
On the basis of Literature Survey following observations were drawn:
Parameter
Value
Springback
Increase
Increase
Decrease
Increase
Modulus of Elasticity
Decrease
Increase
Increase
Increase
Contd..
Parameters
Value
Springback
Friction Coefficient
Increase
Increase
Punch Velocity
Decrease
Increase
Force Applied
Decrease
Increase
Bend Radius
Increase
Increase
Punch Radius
Decrease
Increase
Punch angle
Decrease
Increase
Decrease
Increase
Decrease
Increase
Problem Statement
Springback effect is a major cause of concern for sheet metal forming
industries which leads to inaccuracies in the final product produced and
eventually leads to problems in assembly.
From literature review it is clear that springback effect in case of
perforated sheet metal has not been studied . The problem being taken
for the project is to study the effect of springback phenomenon on
perforated sheet metal.
The study accounts for various controlling parameters for perforation of
sheet metal .
Methodology
Assembly
Die
Material Chosen
The material chosen for Punch and Die is Cast Iron having Youngs
modulus 210 Gpa and Poissons Ratio 0.25.
The material chosen for perforated sheet metal is commercial pure
aluminium having Youngs modulus 70 Gpa and Poissons Ratio
0.33.
Plastic properties of commercial pure aluminium are :
Meshing
Element type : Solid45
Meshing type : Mapped meshing
Element size : For sheet metal 0.75 mm and for punch and die 10
mm.
Contact Pair
Surface-to-surface contact
Node-to-surface contact
Boundary Condition
Die : Constrained in all DOF
Punch: Constrained in X and Z direction
Perforated Sheet: Constrained in X and Z direction
Simulation
X - Component
Y - Component
After Bending
After Unloading
Springback Vs Thickness
Springback Vs Load
Springback Vs Shape
Springback Vs Pattern
Conclusion
The springback effect was studied on perforated sheet metal and the
following conclusions were drawn:
The value of springback effect increases with increase in the percentage
of open area for circular hole as well as square hole when the hole size,
ligament ratio and thickness of sheet metal were taken as constant. Sheet
metal with square hole showed greater springback than those with circular
hole because strength of square hole is less than strength of circular hole.
The value of springback effect decreases with the increase of load on the
perforated sheet metal. This holds good for both the square and circular
hole.
The value of springback effect decreases with increase in hole size for
both circular as well as square holes when open area, ligament ratio and
thickness of sheet metal is kept constant. The values are higher for square
holes.
Contd..
During bending process when the ligament ratio between the holes is
increased the value of springback also gets increased while keeping the
other controlling parameter constant.
When the thickness of perforated sheet metal increases for circular hole
arranged in square pattern then the value of springback value gradually
decreases.
The value of springback in square hole arranged in square pattern was
found to be more than the value of circular hole arranged in square pattern.
This is because the strength of square hole is less than that of a circular
hole.
The value of springback for circular hole arranged in triangular pattern
was found to be less than that of circular hole arranged in square pattern
because the strength of triangular pattern is more than that of square
pattern.
References
Journal Articles:
[1] J. Chakrabarty, W.B. Lee and K.C. Chan (1999), An Analysis of the Plane-Strain Bending of
an Orthotropic Sheet in the Elastic/Plastic Range, Journal of Material Processing
Technology,104, pp 48-52
[2] You-Min Huang, Tsung-Chia Chen. An elasto-plastic finite element analysis of sheet metal
camber process, Journal of Materials Processing Technology, 2003, pp 432-440.
[3] Xuechun Lia, Yuying Yanga, Yongzhi Wanga, Jun Baoa and Shunping Lib (2001), Effect of the
Material-Hardening Mode on the Springback Simulation Accuracy of V-Free Bending,
Journal of Material Processing Technology, pp 209-211.
[4] Zhong Hu, Elasto-Plastic solutions for springback angle of pipe bending using local induction
heating, Journal of Material Processing Technology (200) pp 103
[5] Z. Tan, W. B. Li and B. Persson ( 1993), On Analysis and Measurement of Residual
Stresses in the Bending of Sheet Metals, Pergamon, vol 36, pp 483-491.
[6] J.R.Cho, S.J.Moon, Y.H.Moon and S.S.Kang (2003), Finite Element Investigation on Springback Characteristics in Sheet Metal U-Bending Process, Journal of Material Processing
Technology, pp 109-116.
Contd..
[7] W.M. Chan, H.I. Chew, H.P. Lee and B.T. Cheok (2003), Finite Element Analysis of
Springback of VBending Sheet Metal Forming Processes, Journal of Material Processing
Technology, pp 15 24.
[8] S.K. Panthi, N. Ramakrishnan, Meraj Ahmed, Shambhavi S. Singh and M.D. Goel (2009),
Finite Element Analysis of Sheet Metal Bending Process to Predict the Springback, Materials
and Design, pp 657-662.
[9] Z.Tan, B.Persson and C.Magnusson (1994), Plastic Bending of Anisotropic Sheet Metal,
Pergamon, vol. 37, pp 405-421.
[10] F.Pourboghrat and E. Chu (1995), Prediction of Spring-Back and Side-Wall Curl in 2-D
Draw Bending, Journal of Material Processing Technology, pp 361-374.
[11] M.L. Garcia-Romeu , J. Ciurana and I. Ferrer (2007), Springback Determination Of Sheet
Metals In An Air Bending Process Based On An Experimental Work, Journal of Material
Processing Technology, pp 174-177.
[12] Z.T.Zhang and S.J.Hu, Stress and Residual-108, Stress distribution in plane strain bending,
Journal of Mechanical sciences pp- 543-553
[13] M.A.Osman, M. Shazly, A.El-Mokaddem, A.S.Wifi, Springback prediction in V-bending:
modelling and experimentation, Journal of achievement in Material and Manufacturing
Engineering, pp-179-186
Contd..
[14]
D. Schmoeckel (I) and M. Beth at Institute for Production Technology and Forming
Machines, Springback Reduction In Draw-Bending Process of Sheet Metals, Technical
University Darmstadt Germany, Annals of CIRP, vol. 42, pp 339 342.
[15] Fundamentals of Modern Manufacturing: Materials, Processes, and Systems, Third Edition,
by Mikell P. Groover, 4/25/2008.
Books
[16] ANSYS Structural Analysis, ANSYS Release 9.0, November 2004
[17] Manufacturing processes by S. Kalpakjian and S. Schmid, 4th Edition published by Dorling
Kindersley, 2008.
[18] Mechanics of sheet metal forming by Z.Marciniak, J.L.Duncan and S.J.Hu, 2nd Edition
published by Butterworth-Heinemann 2002.
[19] Z.Marciniak, J.L. Duncun, S.J. Hu Text book of Mechanics of Sheet Metal Forming 82-107.
[20] P.S.G. Design Data Book
Lectures
[21] Lecture on Plastic Deformation By R.Ganesh Narayanan, IITG
THANK YOU