Beruflich Dokumente
Kultur Dokumente
PEM533
PEM533_D00013_00_D_XXEN/06.2013
0.5 S
Product description
The digital universal measuring device PEM533 is suited for measuring and displaying
electrical quantities of electricity networks. The PEM575 is able to perform current, voltage,
energy consumption and performance measurements as well as displaying individual current/
voltage harmonics for assessment of the power quality. The accuracy of active energy
measurements corresponds to class 0.5 S in accordance with the reqirements of DIN EN
62053-22 (VDE 0418 Part 3-22). The current inputs are connected via external /1 A or
/5 A measuring current transformers.
Typical application
PEM533
As a compact device for front panel mounting, the PEM533 is a replacement for analogue
indicating instruments
Typical application in low and medium-voltage networks (via measuring voltage transformer)
Device features
Measured quantities
Description of function
Communication:
Voltage unbalance in %
Current unbalance in %
Standards
The universal measuring device for Power Quality and Energy Measurement/PEM533 was
developed in accordance with the following standards: DIN EN 62053-22 (VDE 0418 Part
3-22), DIN EN 61557-12 (VDE 0413-12)
k-Factor for I
Programmable setpoint monitoring
L ED pulse outputs for active and reactive
energy
Modbus-RTU communication via RS-485
2 digital outputs
Demands of energy and current for
particular time frames
Peak demands with timestamps
Individual current/voltage harmonics up
to the 31st harmonic
Minimum and maximum values
2 PEM533_D00013_00_D_XXEN/06.2013
Features
PEM533
RS-485
Digital inputs
Digital outputs
Sampling rate
THD calculation and harmonics
6
2
3.2 kHz
31.
Operating elements
PEM533
LINETRAXX
kvarh
kWh
3 - Display
4 - V/I button: Selection (in the menu)
5 - POWER button: Up (in the menu)
6 - HARMONICS button: Down (in the menu)
POWER
V/I
HARMONICS
ENERGY
OK
PEM7xx
PEM7xx
Ethernet
Fileserver
Modbus TCP
Modbus TCP
NSHV
L
PEN
CP700
PE
PAS
BMS
PEM5xx
PEM5xx
Modbus TCP
RCMS
I
112
Modbus TCP
Modbus RTU
L
N
PE
Modbus
RTU
112
Modbus RTU
UV2
UV1
PEM3xx
PEM3xx
I
Modbus RTU
RCMS
U
I
Modbus RTU
PEM533_D00013_00_D_XXEN/06.2013 3
Wiring diagram
4
DO13
DO14
DO23
DO24
US
2
DI1
DI2
DI3
DI4
DI5
DI6
AC 400 V/230 V
DIC
Power
A1 A2
RS-485
D+ D- SH
L1
l11
l12
I12
L1
L2
L3
l21
l22
l31
l32
I22
L3
Ri
PEM
I32
I21
I11
L2
I31
L1
L2
L3
AC 400 V
L1
L2
L3
L1
L2
L3
Ri
PEM
L1
Ri
PEM
4 PEM533_D00013_00_D_XXEN/06.2013
L2
L3
Technical data
Insulation co-ordination
Interface
Measuring circuit
Rated insulation voltage
Overvoltage category
Pollution degree
Supply circuit
Rated insulation voltage
Overvoltage category
Pollution degree
Interface/protocol
Baud rate
Cable length
Shielded cable (shield connected to terminal SH on one side)
300 V
III
2
300 V
II
2
Supply voltage
Rated supply voltage US
Frequency range of US
Power consumption
95250 V
DC, 44440 Hz
4 VA
Measuring circuit
Measuring voltage inputs
UL1-N,L2-N,L3-N
230 V
UL1-L2,L2-L3,L3-L1
400 V
Measuring range
10 120 % UN
Rated frequency
4565 Hz
Internal resistance (L-N)
> 500 k
Measuring current inputs
External measuring current transformer
should at least comply with accuracy class 0.5 S
Burden
n.A., internal current transformers
Measuring range
0.1 120 % IN
PEM533/PEM533-455
IN
5A
Measuring current transformer ratio
16000
PEM533-251/PEM533-451
IN
1A
Measuring current transformer ratio
130000
Accuracies (of measured value/of full scale value)
Phase voltage UL1-N, UL2-N, UL3-N
0.2 % of measured value
Current
0.2 % of measured value + 0.05 % of full scale value
Neutral current I4
1 % of full scale value
Frequency
0,02 Hz
Phase position
1
Active energy measurement according to
DIN EN 62053-22 (VDE 0418 Part 3-22)
r.m.s. voltage measurement according to
DIN EN 61557-12 (VDE 0413-12), chapter 4.7.6
r.m.s. phase current measurement according to DIN 61557-12 (VDE 0413-12), chapter 4.7.5
Frequency measurement according to
DIN EN 61557-12 (VDE 0413-12), chapter 4.7.4
RS-485/Modbus/RTU
1.219.2 kbits/s
01200 m
recommended: J-Y(St)Y min. 2 x 0.8
Switching elements
Outputs
2 N/O contacts
Operating principle
N/O operation
Rated operational voltage AC 230 V DC 24 V A C 110 V DC 12 V
Rated operational current
5A 5A 6A
5A
Minimum contact rating
1 mA at AC/DC 10 V
Inputs
6 electrically separated digital inputs
Imin
2.4 mA
UDI
DC 24 V
Environment/EMC
EMC
Operating temperature
Climatic class acc. to DIN EN 60721
Stationary use
Classification of mechanical conditions acc. to DIN EN 60721
Stationary use
DIN EN 61326-1
-25+55 C
3K5
3M4
Connection
Connection
screw-type terminals
Other
Degree of protection, front
Operating manual
Weight
IP54
TGH1476
1100 g
PEM533_D00013_00_D_XXEN/06.2013 5
Ordering information
Interface
RS-485
3(N)AC 690/400 V
Current input
Type
Art. No.
5A
1A
5A
1A
PEM533
PEM533-251
PEM533-455
PEM533-451
B 9310 0533
B 9310 0534
B 9310 0535
B 9310 0536
Dimension diagram
Panel cut-out
Dimensions in mm
Dimensions in mm
106
88
91
92
96
92
96
91
88
18
Subject to change! PEM533_D00013_00_D_XXEN/06.2013 / Schw / Bender GmbH & Co. KG, Germany
18
96
BENDER Group