Beruflich Dokumente
Kultur Dokumente
METHOD STATEMENT
PERMANENT NON REMOVABLE GROUND ANCHOR
PROYEK NORMALISASI KALI CILIWUNG
WASKITA HUTAMA JO
Revision 01
May 2014
L &M
PT. L&M SYSTEMS INDONESIA
JL. JUANDA III No. 8
KEBON KELAPA GAMBIR, JAKARTA 10120
TELP : 021 - 345 8568
FAX : 021 - 345 4044
1
TABLE OF CONTENT
1. GENERAL..3
2. TENDON ASSEMBLY..3
3. SEQUENCE OF INSTALLATION4
4. STRESSING4
5. GROUT MIX PROPORTION.5
6. MATERIAL SPECIFICATION..6
7. QUALITY CONTROL6
8. RECORDING..7
9. EQUIPMENT..7
APPENDIX A
APPENDIX B
LIST OF EQUIPMENT
APPENDIX C
APPENDIX D
APPENDIX E
ILLUSTRATION DRAWINGS
METHOD STATEMENT
PERMANENT NON REMOVABLE GROUND ANCHOR
I. GENERAL
This method statement is
prepared to state the proposed
construction method for Permanent Non
Removable Ground Anchor Work and
shall be after approval is given by the
engineer, distributed to all parties
concerned so that the Ground Anchor
Works work may be carried out with the
same information.
The NORMALISASI KALI CILIWUNG
Project requires a Permanent Non Removable
Ground Anchor as a part of Sheet Pile structure
to execute the river excavation.
This method statement describes the step
by step sequential order of the operation
entailed in :
1. Fabrication / Assembly
2. Drilling, Installation and Grouting
3. Stressing
4. Remove / Releasing
II. TENDON ASSEMBLY AND
CONFIGURATION
The effective strands shall comprise of
12.7 mm diameter uncoated 7-wire Low
Relaxation PC Strand in compliance wiyh
ASTM A-416 Grade 270 Low Relaxation with
minimum breaking strength of 183.7 kN (UTS).
As the system was Permanent Ground
Anchor, the tendons configuration as follow :
1. They are fully greased and sheated
with HDPE hose as specified
2. At end node of tendon detailed with
looping 600 mm pitch 2 stagings 3
number of strands each loop.
3. To binding strands into tendons each
1.00 m pitch to be spaced plastic
I. UMUM
spacer and centralizer in order to
keep tendon cnter to drilling hole.
Metode Pelaksanaan ini disiapkan
sebagai proporsal metode konstruksi untuk
pekerjaan Permanent Non Removable Ground
Anchor dan setelah disetujui oleh konsultan,
didistribusikan kepada semua pihak yang
terlibat agar pekerjaan Ground Anchor ini dapat
dilaksanakan dengan informasi yang sama.
Proyek NORMALISASI CILIWUNG
ini memerlukan Permanent Non Removable
Ground Anchor sebagai bagian dari strutur
Sheet Pile untuk pelaksanaan normalisasi
sungai.
Metode kerja ini menggambarkan
langkah demi langkah urutan kerja sebagai
berikut :
1. Fabrikasi
2. Pengeboran,
Pemasangan
dan
Grouting.
3. Penarikan
4. Pembongkaran.
II. PERAKITAN TENDON DAN
KONFIGURASI
Strand yang dipakai adalah diameter
12.7 mm type uncoated 7-kabel sesuai standar
ASTM A-416 Grade 270 Low Relaxation
dengan kekuatan putus minimal 183.7 kN
(UTS).
Sesuai dengan sistem Permanent
Ground Anchor konfigurasi tendon adalah
sebagai berikut :
1. Seluruh permukaan PC Strand dilapisi
gemuk dan dibungkus dengan pipa
HDPE sebagaimana yang disyaratkan.
Water
Cement
Add. Tricosal
W/C Ratio
Strength 7 d
Strength 28 d
= 21 22.5 ltr
= 50 kg
= 500 grams
= 0.42 0.45
= 30 N/mm2
= 40 N/mm2
additive
below :
TABLE 1 :
ACCEPTANCE TEST LOAD CYCLE
10
50
100
125
100
50
10
1
1
1
15
1
1
1
V.
Air
= 21 22.5 ltr
5
Semen
= 50 kg
Add. Tricosal = 500 grams
W/C Ratio
= 0.42 0.45
Kuat Tekan 7d = 30 N/mm2
Kuat Tekan 28d = 40 N/mm2
Item
Materials
Water
1
2
3
4
5
6
Position
Alignement
Inclination
Drill Length
Anchor Tendon Installed Length
Grout Strength
Specification Code
Specification Code
Item
be
1. Daily Report
2. Ground Anchor Installation Record
3. Groung Anchor Stressing Records
Sample of the above recording forms is
attached.
IX. EQUIPMENTS
The following are the main equipment that will
be used for this project.
1. Drill Rig
2 Nos
2.
3.
4.
5.
2 Sets
2 Nos
2 Nos
2 Nos
Grout Mixer
Grout Pump
Stressing Jack 200 T
Twin Hydraulic Pump
1. Laporan harian
2. Rekaman Pemasangan Ground Angkur
3. Rekaman Stressing Ground Angkur
2 unit
2.
3.
4.
5.
2 Set
2 unit
2 unit
2 unit
Grout Mixer
Grout Pump
Stressing Jack 200 T
Twin Hydraulic Pump