Sie sind auf Seite 1von 20

Featured Products

Third Generation SATA-to-Dual


eSATA Storage Processor

The SteelVine® Series 3 Core storage


processor features a 3Gbps SATA host
interface and two eSATA capable device
ports. The SiI5923 features Silicon Image
performance RAID, which allows users to
easily speed up or add automatic back up
by adding additional drives as needed...
more on page 6

In This Issue:

April 2010
GS2994/GS2993…these are not just any
SD/HD/3G-SDI Adaptive Equalizers
Audio / Video

These are Gennum’s 4th-generation SD/HD/3G adaptive cable equalizers

The GS2994 and GS2993 are high-speed BiCMOS integrated circuits designed to equalize and restore signals received over 75Ω coaxial cable. The devices
are designed to support SMPTE 424M, SMPTE292M and SMPTE 259M, and is optimized for performance at 270Mb/s, 1.485Gb/s and 2.97Gb/s. The GS2994
and GS2993 feature DC restoration to compensate for the DC content of SMPTE pathological test patterns.

The Carrier Detect output pin (CD) indicates whether a valid input signal has been detected. It can be connected directly to the SLEEP pin to enable automatic
power-down upon loss of carrier. A voltage programmable threshold, which can be changed via the SQ_ADJ pin, forces CD high when the input signal
amplitude falls below the threshold. This allows the GS2994 and GS2993 to distinguish between low-amplitude SDI signals and noise at the input of the
device.

The equalizing and DC restore stages are disengaged when the BYPASS pin is HIGH. No equalization occurs in Bypass mode. The GS2994 and GS2993 include
a gain selection pin (GAIN_SEL) which, when tied HIGH, compensates for 6Db flat attenuation. The differential outputs can be DC-coupled to Gennum 3.3V
cable drivers and reclockers and to industry-standard 1.2V, 2.5V and 3.3V using the VCC_O pin for the GS2994 and the OP_CTL pins for the GS2993.

Features
 SMPTE 424M, SMPTE 292M and SMPTE 259M compliant
 Automatic cable equalization
 Multi-standard operation from 143Mb/s to 2.97Gb/s
 Performance optimized for 270Mb/s, 1.485Gb/s and 2.97Gb/s. Typical
equalized length of Belden 1694A cable:
 140m at 2.97Gb/s
 200m at 1.485Gb/s
 400m at 270Mb/s
 Supports DVB-ASI at 270Mb/s
 Manual bypass (useful for low data rates with slow rise/fall times)
 Programmable carrier detect with squelch threshold adjustment
 Automatic power-down on loss of signal
 Standby power <30mW (typical)
 Differential outputs support DC-coupling to 1.2V, 2.5V and 3.3V CML logic
 0/6 dB gain boost selection pin
 Selectable de-emphasis: 2dB, 4dB and 6dB
 Standard EIA/JEDEC logic control and status signal levels
 Single 3.3V power supply operation
 Power consumption is typically 160mW
 Wide operating temperature range of -40ºC to +85ºC
 Small footprint 16 pin QFN package (4mm x 4mm)

Applications
 Serial routing switchers
 Professional video editing equipment
 Production and master control switchers
 Distribution amplifiers
 Broadcast video to Fiber Channel or Gigabit Ethernet transport linecards
 Camera control units for medical imaging equipment

2 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
B attery Management
LTC4425 - Linear SuperCap Charger with Current-
Limited Ideal Diode and V/I Monitor
Programmable 2A 2-Cell Supercap Charger with Automatic Cell Balancing
in a Compact 9mm2 Package
The LTC®4425 is a constant-current/constant-voltage linear charger
designed to charge a 2-cell supercap stack from either a Li-Ion/
Polymer battery, a USB port, or a 2.7V to 5.5V current-limited supply.
The part operates as an ideal diode with an extremely low 50mΩ
on-resistance making it suitable for high peak-power/low average
power applications. The LTC4425 charges the output capacitors to
an externally programmed output voltage in LDO mode at a constant
charge current, or to VIN in normal mode with a smart charge current
profile to limit the inrush current until the VIN to VOUT differential is
less than 250mV. In addition the LTC4425 can be set to clamp the
output voltage to 4.9V or 5.4V.

Charge current (VOUT current limit) is programmed by connecting


a resistor between PROG and GND. The voltage on the PROG pin
represents the current flowing from VIN to VOUT for current monitoring. An internal active balancing circuit maintains equal voltages across each supercapacitor
and clamps the peak voltage across each cell to a pin-selectable maximum value. The LTC4425 operates at a very low 20μA quiescent current (shutdown
current <3μA) and is available in a low profile 12-pin 3mm × 3mm DFN or a 12-lead MSOP package.

Charging 2-Cell Series Supercapacitor from Li-Ion Source Features Charge Current vs VIN to VOUT
 50mΩ
0.6 Ideal Diode from VIN to VOUT
VOUT VIN FULL CHARGE CURRENT VFB = VIN
VIN TO HIGH PEAK  Smart Charge Current Profile Limits Inrush Current
POWER LOAD 0.5
Li-Ion
 Internal Cell Balancer (No External Resistors)
1F
CHARGE CURRENT (A)

1.5M
VMID  Programmable
0.4 Output Voltage (LDO Mode)
PFI 1F  Programmable VIN to VOUT Current Limit
0.3 CURRENT LIMITED
+ – VIN
BY Monitoring
PMOS RDSONof V to V
FB  Continuous IN OUT Current via PROG Pin
1.2M
 Low0.2Quiescent Current: 20μA 1/10 CHARGE
470k CURRENT
PFI_RET LTC4425 PFO
 VIN Power Fail, PGOOD Indicator
0.1
PROG  2.45V/2.7V IDEAL DIODE
Cell Protection Shunts
IMONITOR FORWARD VOLTAGE = 15mV
SEL 2.45V/2.7V (4.9V/5.4V
0 SuperCap Max Top-Off Voltage)
0 0.2 0.4 0.6 0.8 1
2k
EN  3A Peak Current Limit,
VINThermal
– VOUT (V)Limiting
GND
 Tiny Application Circuit, 3mm × 3mm × 0.75mm DFN and
12-Lead MSOP Packages

ource Charge Current vs VIN to VOUT


0.6 Applications
FULL CHARGE CURRENT VFB = VIN
O HIGH PEAK  High Peak Power Battery/USB Powered Equipment
OWER LOAD 0.5
 Industrial PDAs
CHARGE CURRENT (A)

0.4  Portable Instruments/Monitoring Equipment


 Power Meters, SuperCap Backup Circuits
0.3 CURRENT LIMITED
BY PMOS RDSON  PC Card/USB Modems
0.2
1/10 CHARGE
CURRENT
0.1
IDEAL DIODE
ITOR FORWARD VOLTAGE = 15mV
0
0 0.2 0.4 0.6 0.8 1
VIN – VOUT (V)

3
SP336 - Ultra-Versatile 3.3V/5.0V Single-Chip
RS-232/RS-485/RS-422 Serial Transceiver
B us I nterface

Advanced Features Deliver Maximum Design Flexibility for Rugged Industrial Markets

The SP336 is a highly integrated multiprotocol serial transceiver that contains both
RS-232 and RS-485/422 drivers and receivers. The SP336 can be configured into eight
operating modes including RS-232-only (4Tx/4Rx), RS-485/RS-422-only (2Tx/2Rx) full
or half duplex, two RS-232/RS-485/RS-422 mixed-modes, two shutdown modes and a
diagnostic loop-back mode. All RS-485 receivers feature high input impedance, which
allows up to 256 transceivers on a shared bus. All bus input and output pins are ESD
protected up to +/-15kV IEC 61000-4-2 air-gap and +/-8kV IEC 61000-4-2 contact
discharge.

Features Benefits
 Operates from a Single 3.3V or 5V Supply Voltage  Best-in-Class 15kV ESD (Air gap) for Rugged Applications in Industrial
Environments
 Up to 10 Mbps for RS-485/422 and Up to 1Mbps for RS-232
 Slew Rate Control Feature - Up to 250kbps
 Re-Configurability into Five Serial Protocol Modes - RS-232 Mode,
 +/- 15kV ESD Protection (IEC 61000-4-2, Air-Gap) Full or Half Duplex RS-485/RS-422 Modes, Two Mixed-Modes,Enables
 +/- 8kV ESD Protection (IEC 61000-4-2, Contact) Customers to Configure the Serial Port to Meet Many Application Needs
 1/8th Load in RS-485 Mode (Max. 256 Transceivers on
the Communication Bus)  Selectable Slew Rate Controlled Outputs Minimize Problems with
Reflections and Ringing on Long or Un-Terminated Cables
 Advanced Failsafe Feature (RS-485/422 mode)
 Diagnostic Loop Back Function
 Driver Short-Circuit Protection Thermal Shutdown Overload
Protection

PART NUMBER PACKAGE OPERATING TEMPERATURE RANGE DEVICE STATUS


SP336ECT-L 28-pin WSOIC 0°C to +70°C Active
SP336ECY-L 28-pin TSSOP 0°C to +70°C Active
SP336EET-L 28-pin WSOIC -40°C to +85°C Active
SP336EEY-L 28-pin TSSOP -40°C to +85°C Active

Applications
 Factory Automation Equipment
 Security Networks
 Industrial/Process Control Networks
 Point-of-Sales Equipment
 Gaming Machines
 Serial Protocol Translators (ex. RS-232 to RS-485/422)
 Embedded Industrial PC’s
 Building Environmental Control Systems (ex. HVAC)
 Cable Repeaters / Port Extenders/ Hubs

4 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
LTC3865 - Dual, 2-Phase Synchronous DC/DC

D C /D C C ontroller
Controller with Pin Selectable Outputs
1% Accurate Pin-Selectable Output Voltages

The LTC®3865/LTC3865-1 are high performance dual


synchronous step-down DC/DC switching regulator controllers
that drive all N‑channel synchronous power MOSFET stages.
A constant frequency current mode architecture allows a
phase-lockable frequency of up to 770kHz. Power loss and
noise are minimized by operating the two controller output
stages out of phase.

OPTI-LOOP® compensation allows the transient response


to be optimized over a wide range of output capacitance
and ESR values. Independent track/soft-start pins for each
controller ramp the output voltage during start-up. Current
foldback limits MOSFET heat dissipation during short-
circuit conditions. The MODE/PLLIN pin selects among Burst
Mode® operation, pulse-skipping mode, and continuous
inductor current mode. The output voltages can be precisely
programmed by pin strapping or external resistors.

The LTC3865/LTC3865-1 are available in low profile (5mm ×


5mm) 32-pin QFN and 38-Lead thermally enhanced TSSOP
packages.

High Efficiency 1.5V/15A, 1.2V/15A Step-Down Converter


VIN
+ 22µF
4.5V TO 24V
2.2
50V Efficiency and Power Loss
1µF vs Load Current
100 10
VIN = 12V
4.7µF 90 VOUT = 1.5V
VIN INTVCC
TG1 TG2 80
0.1µF 0.1µF
70
1

POWER LOSS (W)


0.47µH BOOST1 BOOST2 0.47µH EFFICIENCY
EFFICIENCY (%)

60
SW1 SW2 POWER LOSS
LTC3865 50
BG1 BG2
40
PGND 0.1
30
100 FREQ 100
SENSE1+ SENSE2+ 20
2m 1000pF 1000pF 2m 10
SENSE1– SENSE2– 0 0.01
100 VID11 VID21 100 0.01 0.1 1 10 100
VOUT1 VID12 VID22 VOUT2 LOAD CURRENT (A)
1.5V VOSENSE1 VOSENSE2 1.2V
15A + ITH1 ITH2 + 15A
COUT2,3 1000pF TK/SS1 SGND TK/SS2 1000pF COUT5,6

100µF 10k 100pF 0.1µF 0.1µF 162k 15k 100pF 100µF

Features Applications
 Dual, 180° Phased Controllers  DC Power Distribution Systems
 2-Pin VID Output Voltage Programming from 0.6V to 5V
 High Efficiency: Up to 95%
 RSENSE or DCR Current Sensing
 Phase-Lockable Fixed Frequency 250kHz to 770kHz
 Adjustable Current Limit
 Dual N-Channel MOSFET Synchronous Drive
 Wide VIN Range: 4.5V to 38V Operation
 Adjustable Soft-Start Current Ramping or Tracking
 Output OV Protection With Reverse Current Limit
 Power Good Output Voltage Monitor
 32-Pin 5mm × 5mm QFN and 38-Lead TSSOP Packages

5
SiI5923 - Third Generation SATA-to-Dual eSATA
D isk / I nterface

Storage Processor
The SteelVine® Series 3 Core storage processor is a low-cost, single chip solution
designed to be built into PC motherboards, DVRs and consumer electronics devices.

The SteelVine® Series 3 Core storage processor features a 3Gbps SATA data repair to provide higher levels of protection for your customer’s critical
host interface and two eSATA capable device ports. The SiI5923 features data. Management parameters can be customized using the Manufacturing
Silicon Image performance RAID, which allows users Utility or through customer applications built using the
to easily speed up or add automatic back up by adding SiI5923 Software Development Kit. SiI5923 storage
additional drives as needed. processor supports JBOD and the following RAID modes:
FAST (RAID 0) and SAFE (RAID 1). RAID mode configuration
The SteelVine Series 3 Core storage processor extends can be accomplished through a System Management
the capabilities of PC motherboards, DVR devices, and Bus (SMBus)-based GUI or strap pins for true software-
consumer electronics by adding eSATA and advanced free implementation. The SiI5923 reduces your power
storage features on a single chip that easily integrates budget by entering aggressive power-down modes when
with existing designs via a SATA connection. Advanced drive(s) are idle or not present. The economical 40-pin
features include enhanced sector recovery and automatic QFN package offers a small footprint implementation.

SiI5923 System Diagram

SiI5923 Block Diagram Key Features


 Storage Offload Engine (100%)
 eSATA Capable Device Ports
 RAID 1 Performance (Racing)
 RAID 1 Rebuild Boost
 Easy to Use Auto Mirror / Failover
 High Performance - Hardware Acceleration
 RAID 0 Striping

Applications
 PC Motherboards
 DVR Motherboards
 CE Motherboards
 SSD Drives Accelerator
 USB 3.0 Bridge Accelerator

6 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
MIC3201 - High Brightness LED Driver
The MIC3201 is a hysteretic step-down, constant-current, High-Brightness LED

LED D rivers
(HB LED) driver with High-Side Current Sense
The MIC3201 is a hysteretic step-down, constant-current, High-Brightness LED (HB LED) driver capable
of driving up to four, 1A LEDs. It provides an ideal solution for interior/exterior lighting, architectural and
ambient lighting, LED bulbs, and other general illumination applications.

The MIC3201 operates with an input voltage range from 6V to 20V. The hysteretic control gives good supply
rejection and fast response during load transients and PWM dimming. The high-side current sensing and
on-chip current sense amplifier delivers LED current with ±5% accuracy. An external high-side current
sense resistor is used to set the output current.

The MIC3201 offers a dedicated PWM input (DIM) which enables a wide range of pulsed dimming. A high
switching frequency operation up to 1MHz allows the use of smaller external components minimizing
space and cost.

The MIC3201 operates over a junction temperature range of -40°C to +125°C and is available in an 8-pin
ePad SOIC package.

Features Benefits
 6.0V to 20V input voltage range  The first in a family of HB LED Driver products spanning a variety of
 High efficiency (>90%) current ranges
 ± 5% LED current accuracy  Provides Constant Current even with changes in input voltage and
 High-side current sense output load (diff. # of LEDs)
 Dedicated dimming control input  Input Voltage range from 6V to 20V
 Hysteretic control (no compensation!)
 Switching Frequency adjustable upto 1MHz
 1A internal power switch
 Up to 1MHz switching frequency  Integrated 1A (Current limit at 1.2A) Power Switch
 Adjustable constant LED current  PWM Dimming
 5V on board regulator  Efficiency > 90%
 Over temperature protection
 High side current sense capability
 –40°C to +125°C Junction temperature range
 Thermally enhanced SOIC package  Ease of use with no compensation and low parts count

Applications
 Broad range of Applications for all regions
 MR-16 Bulbs
 Garden Pathway Lighting
 Under Cabinet Lighting
 Street Lighting
 Emergency Vehicle Lighting and Signals
 Loosely regulated 12V Systems
 Channel Letters
 Constant Current Power Supplies

7
LT3032 - Dual 150mA Positive/Negative Low Noise
Linear R egulator

Low Dropout Linear Regulator


Dual Positive/Negative ±20VIN ±150mA LDO Offers 20µVRMS
The LT®3032 is a dual, low noise, positive and negative low dropout
voltage linear regulator. Each regulator delivers up to 150mA with a
typical 300mV dropout voltage. Each regulator’s quiescent current is
low (30μA operating and <3μA in shutdown) and well-controlled in
dropout, making it an excellent choice for battery-powered circuits.

Another key feature of the LT3032 is low output noise. Adding an


external 10nF bypass capacitor to each regulator reduces output
noise to 20μVRMS/30μVRMS over a 10Hz to 100kHz bandwidth. The
LT3032 is stable with minimum output capacitors of 2.2μF. The
regulators do not require the addition of ESR as is common with
other regulators.

Internal protection circuitry includes reverse output protection,


current limiting, and thermal limiting. Each regulator is offered as an
adjustable output device with an output voltage down to the ±1.22V
reference voltages.

The LT3032 is available in a unique low profile 14-lead 4mm × 3mm × 0.75mm DFN package with exposed backside pads for each regulator, allowing
optimum thermal performance.

Features
Dual Polarity Low Noise 150mA Power Supply 10Hz
 Low Noise: 20μV to 100kHz Output Noise
RMS (Positive) and 30μVRMS (Negative)
 Low Quiescent Current: 30μA/Channel
LT3032 5V OUT AT 150mA
INP OUTP 20µVRMS NOISE  Wide Input Voltage Range: ±2.3V to ±20V
5.4V TO 768k OUTP 20µVRMS
20V ADJP 0.01µF  Output Current: ±150mA
100µV/DIV
10µF 10µF  Low Shutdown Current: <3μA Total (Typical)
<0.25V = OFF 249k
SHDNP
>2V = ON
BYPP
 Low Dropout Voltage: 300mV/Channel
GND  Adjustable
OUTN Outputs from ±1.22V to ±20V 30µVRMS
BYPN 100µV/DIV
 No Protection Diodes Needed
SHDNN
10µF 249k 10µF  Stable with 2.2μF Output Capacitors
ADJN 1mS/DIV 3032 TA02a

–5.4V TO 0.01µF  Stable with Ceramic, Tantalum or Aluminum Capacitors


–20V 768k
–5V OUT AT –150mA  Starts into Reverse Output Voltage
INN OUTN 30µVRMS NOISE
 Current Limit and Thermal Limit
 Low Profile 14-Lead 4mm × 3mm × 0.75mm DFN Package

upply 10Hz to 100kHz Output Noise


Applications
 Battery-Powered Instruments
5V OUT AT 150mA
 Bipolar Power Supplies
20µVRMS NOISE
OUTP 20µVRMS
100µV/DIV
 Low Noise Power Supplies
10µF

OUTN 30µVRMS
100µV/DIV

10µF
1mS/DIV 3032 TA02a

–5V OUT AT –150mA


30µVRMS NOISE
8
SigmaQuad-IITM and SigmaDDR-IITM SRAMs
GSI Technology now offers the highest density Type-II+
devices designed for higher speeds

Mem ory
By offering a 144Mbit density SRAM, GSI provides a memory upgrade path for 72Mbit designs. Existing SRAM memory
controllers can be reused with 144Mbit densities, which make for an easy design decision. With the simple addition of
an address signal you get double the density. The same package is used for both the 72Mbit and 144Mbit—15 mm x 17
mm 165 FBGA—which eliminates any footprint issue.

The 144Mbit family of SigmaQuad-II+ and SigmaDDR-II+ SRAMs achieve higher operating frequencies, in part, because they are designed with a longer
read pipeline. When described in terms of cycles of latency, Type-II SRAMs demonstrate a 1.5 cycle read latency, while Type-II+ SRAMs are offered with read
latencies of either 2.0 or 2.5 cycles. The multiple read latency selections allow designers more flexibility to optimize SRAM performance in their particular
applications. Type-II+ SRAMs also offer optional On-Die Termination (ODT) to improve signal integrity. ODT can be enabled or disabled via the ODT pin—a low
(0) disables ODT while a high (1) enables ODT.
Density Type Burst RL Speed Width Part Number
GSI offers both leaded packages for those designs that
8 GS81302D07E/GE-xxx
have not transferred to green manufacturing processes and
RoHS-compliant packages for applications that demand 9 GS81302D10E/GE-xxx
SigmaQuad-II+ 4 2.0 400–300
environmentally friendly products. All devices are offered in 18 GS81302D19E/GE-xxx
Industrial temperature and Commercial temperature ranges. 36 GS81302D37E/GE-xxx
Special testing is available for applications that require wider
8 GS81302T07E/GE-xxx
temperature and voltage limits. For more information, please
visit www.gsitechnology.com. 9 GS81302T10E/GE-xxx
SigmaDDR-II+ 2 2.0 400–300
18 GS81302T19E/GE-xxx

Features 144Mbit
36 GS81302T37E/GE-xxx
8 GS81302D06E/GE-xxx
 Highest densities—144Mbit 9 GS81302D11E/GE-xxx
 Broadest range of organizations—x8, x9, x18, x36 SigmaQuad-II+ 4 2.5 450–300
18 GS81302D20E/GE-xxx
 Highest speeds—up to 333 MHz for Type–II and
450 MHz for Type–II+ 36 GS81302D38E/GE-xxx
 On-Die Termination and two Read Latency 8 GS81302T06E/GE-xxx
offerings for Type–II+ products 9 GS81302T11E/GE-xxx
SigmaDDR-II+ 2 2.5 450–300
18 GS81302T20E/GE-xxx
36 GS81302T38E/GE-xxx
Benefits
 Focused SRAM supplier providing one stop Density Type Burst Speed Width Part Number
shopping with over 9000 different products 8 GS81302D08E/GE-xxx
 ExactPreferenceTM Master die design methodology 9 GS81302D09E/GE-xxx
 Short lead times SigmaQuad-II 4 333–167
18 GS81302D18E/GE-xxx
 Minimum 7-year product life cycle
 FLXDrive-II output impedance control 36 GS81302D36E/GE-xxx
 Custom products for application specific designs 8 GS81302Q08E/GE-xxx
9 GS81302Q09E/GE-xxx
SigmaQuad-II 2 250–167
Applications 18 GS81302Q18E/GE-xxx
36 GS81302Q36E/GE-xxx
 Networking and Telecom infrastructure
 Switches 8 GS81302R08E/GE-xxx
 Routers 9 GS81302R09E/GE-xxx
 Base stations 144Mbit SigmaDDR-II 4 333–167
18 GS81302R18E/GE-xxx
 Common Uses
36 GS81302R36E/GE-xxx
 Table look-ups
 Statistics accumulation 8 GS81302T08E/GE-xxx
 Military 9 GS81302T09E/GE-xxx
 Test and Measurement SigmaDDR-II 2 333–167
18 GS81302T18E/GE-xxx
 Medical Imaging
36 GS81302T36E/GE-xxx
8 GS81302S08E/GE-xxx

SigmaSIO 9 GS81302S09E/GE-xxx
2 333–167
DDR-II 18 GS81302S18E/GE-xxx
36 GS81302S36E/GE-xxx

9
New STM32 Value Line extends choice for Cost
Microcontrollers

Sensitive Applications
Available in devices priced under $1 the STM32 Value Line delivers 32-bit MCU
performance and advanced feature set
The new STM32 Value Line (STM32F100) combines a 24 MHz Cortex-M3
core with a feature set optimized for applications previously supported by
16-bit MCUs. Delivering 30 DMIPS yet available in devices priced below $1
the STM32 Value Line brings new levels of performance and affordability
to this class of applications. Application-focused features include up to 12
16-bit timers (including a PWM timer for motor-control applications), 12-
bit high speed ADC, 12-bit DAC and CEC for consumer applications.

The STM32 Value Line is fully pin-and-software compatible with the


existing STM32 product lines and takes advantage of the available broad
ecosystem of STM32 development tools and firmware libraries.

Features Benefits
 24 MHz Cortex-M3 and 7-channel DMA  Industries broadest range of fully compatible Cortex-M3 MCUs
 16 – 128 KB Flash and 4 – 8 KB SRAM  Value Line offers 16-bit pricing with 32-bit MCU performance
 Seven PWM 16-bit timers including motor control timer and advanced feature set
 Advanced analog 12-bit ADC and 12-bit DAC
 3-Mbit/s USART, 12-Mbit/s SPI, 400-kHz I²C, CEC STM32 Value Line Devices:
 Built-in reset, watchdog, PLL, oscillator, RTC  STM32F100C4T6B  STM32F100R6T6B 
 STM32F100C6T6B  STM32F100RBH6B
 STM32F100C8T6B  STM32F100RBT6B
 STM32F100CBT6B  STM32F100V8T6B
 STM32F100R4T6B  STM32F100VBT6B

Development Tools Applications


 STM32100B-EVAL  Factory Automation
 STM32 Development Tools  Industrial networks
http://www.st.com/mcu/inchtml-pages-stm32_tools.html  PLC
 Security and Surveillance
 Alarm panels
 Building automation
 Aftermarket automotive
 Diagnostics
 Consumer audio
 Communication serial protocol
 Gateways
 Office phones
 Portable medical

10 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
PowerXR - Evolutionary Solutions for Multi Channel

Power Management
Digital PWM Step Down Controllers
The XRP7704, XRP7708, XRP7713, XRP7714, and
XRP7740, members of the Power XR family, are pulse-
width modulated (PWM) step-down DC-DC controllers
with a built-in LDO for standby power and GPIOs.
The devices provide a complete power management
solution in one IC and are fully programmable via the
included I²C serial interface. Independent Digital Pulse
Width Modulator (DPWM) channels regulate output
voltages and provide all required protection functions Features
such as current limiting and over-voltage protection.
 Pin/Function Compatible 4-Channel  On Board Standby Power LDO
PWM Controllers  On Board Gate Drivers
Each output voltage can be programmed from 0.9V to
 XRP7704: 4 x 5A Channels
5.1V without the need of an external voltage divider.  Up to 25V Single Input Voltage
 XRP7708: 2 x 5A and 2 x 8A Channels
The wide range of the programmable DPWM switching  0.9V Min. Programmable Output Voltage
 XRP7713: 3 x 5A Channels
frequency (from 300 KHz to 1.5 MHz) enables the user  Independent Channel (re)Configurability
to optimize between efficiency and component size. An  XRP7714: 4 x 5A Channels
 I²C Controlled
I²C bus interface is provided to program the ICs as well  XRP7740: 2 x 5A and 2 x 15A Channels
 40-pin QFN and 32-pin QFN (XRP7713 only)
as to communicate with the host for fault reporting  Digital Loop Control packages
and handling, power rail parameters monitoring, etc.
The start-up delay and ramp of each PWM regulator Applications
can be independently controlled and offers a complete
 Multi Channel Power Supplies
solution for programmable soft-start and soft-stop.
 Programmable Power Supplies
Additional information on Exar’s Digital Power  Audio- Video Equipments
solutions can be found at www.exar.com/digitalpower  Processors and DSP based
or by contacting digitalpower@exar.com. Applications

XRP7704 / XRP7740
Single Input
Voltage Clock
OTP LDO 3.3V/5V LDO
OSC
GPIOs

Port
Digital Gate
FETS

Expansion Supply 1
PWM Driver
I2C I2C
Interface Digital Gate
FETS

Supply 2
Registers

PWM Driver
Power Good
OCP-UVLO

Digital Gate
FETS

Supply 3
PWM Driver

Digital Gate
FETS

Supply 4
PWM Driver

11
XXXXXXXXXX

Setting New Standards for Signal Integrity


Solve your signal integrity issues with Vitesse’s advanced IC solutions. With Vitesse’s VScope™
embedded waveform viewing technology, the power to take signals farther, faster is yours.

Visit us at NAB, Booth #N5921 or online at www.vitesse.com/nuho.

12
Wireless LAN SPI/SDIO modules for industrial
applications - OWL221a and OWL222a

Wireless
Fully radio type approved, dual-band Wireless LAN modules supporting 802.11abgn

The OEM Wireless LAN Modules OWL221a and OWL222a


from connectBlue has been developed for integration in high
demanding industrial devices providing state of the art low power
features, reliability and compatibility.

Using these modules minimize the work needed to implement


Wireless LAN (IEEE 802.11a/b/g/n) in a device as it provides
all hardware, EMC certifications and radio type approvals such
as R&TTE, FCC and IC. This lowers the time-to-market, the
requirements of in-house radio knowledge and any design
uncertainties.

The accompanying software driver works as the interface


between the TCP/IP stack in the host device and the module, is
available for Linux, WinCE and embedded systems and may be
adapted for any micro controller.
Features
The interface to the module is either SPI (up to 80 MHz) or
 Supports 802.11a/b/g/n
SDIO (v2.0 up to 50 MHz). For easiest integration a version with
 Dual band 2.4GHz/5GHz
integrated antenna is available, but a version with connectors for
 802.11n single-stream
external antennas is also available to allow for the module to be
 802.11n space time block code for extended range and throughput
mounted inside metal enclosures. To improve the radio properties
 SPI (80MHz) or SDIO (50MHz) Host interface
even further you can also connect dual external antennas for
 Software driver available and adaptable for any device
diversity support.
 Radio type approved for Europe, US and Canada (R&TTE, FCC, IC)
 Compliant with EMC standards
As with all connectBlue modules the form factor, interface and
 Industrial temperature range (-30 to +85°C)
connectors layout is kept the same over time and over radio
 Small size (23x36 mm)
technologies. This means that a product can be designed for
 Internal or dual external antennas (diversity support)
using different radio technologies like Bluetooth or Wireless LAN,
 Wide range of development/evaluation kits available
but also be prepared for using upcoming modules when new
 Bluetooth coexistence protocol
modules implementing new features are available.
 Hardware support for IEEE 802.15.2 Packet Traffic Arbitration
 Support of 802.11e (WMM Quality of Service)
To accelerate the customer’s evaluation, product design,
 Support of 802.11i (MAC security enhancements)
development and delivery a wide range of Wireless LAN
 WEP64, WEP128
development kits are available. The kits collection spans over a
 TKIP, AES (CCMP)
wide variety of customer development needs. For instance, there
 PEAP
are choices of complete out-of-the-box test system, or software
 WPA-EAP-TLS, WPA-PSK
kits for integration into one’s own existing system for evaluation.
 WPA2-EAP-TLS, WPA2-PSK
 Advanced power save mode
 Infrastructure/Ad-hoc modes
 Wide range of radio approved antennas Applications
 Hardware accelerators for WEP, TKIP, and AES
 Industrial control systems
 Hardware accelerators for IPSec and TCP/IP checksum offloading
 Medical devices
 Point of Sale payment systems
Benefits  Data acquisition instruments
 Network connectivity
 Radio type approved for shortened time-to-market  Mobile internet access
 5GHz support for wider selection of available radio channels  Portable printing devices
 Dual band support for compatibility with the installed base of  Ethernet cable replacement
802.11a and 802.11bgn devices  Warehouse management systems
 Increased throughput using 802.11n
 Environmental friendly by low power consumption
 External antenna option for mounting in metal enclosures
 Minimal host processor load
 Compatible with other connectBlue radio modules
 Compatible with upcoming connectBlue modules
 RoHS compliant

13
Display Technologies available from Nu Horizons
Cable Solutions LCD Controller Solutions
Quadrangle Amulet Technologies
Digital View
Display Enhancement Solutions Digitron
Landmark Estecom-USA
Nu Horizons Custom Solutions Kordis
Spectrah
Displays URT
Emerging Display Technologies (EDT)
HT Displays Open Frame/Panel PC Solutions
T E C H N O L O G Y I N C.

Optrex Aaeon
OSD Displays Axiom Tek
Sharp Digitron
Tianma Estecom-USA
United Radiant Technology Corp. (URT) IEI Technology
Nu Horizons Custom Solutions
Inverters Slimage
Applied Concepts Spectrah
ERG
Microsemi Touchscreens
Zippy Hantouch
Touch International
LCD Monitors
Axiom Tek
Digitron
Estecom-USA
IEI
Slimage

Embedded Solutions available from Nu Horizons

Offering Embedded Computing Platforms so that


customers have a single, reliable, cost-effective source
to a wide array of CE, FCC & UL certified products.
These products include single board computers,
embedded systems and barebone systems, panel
computers, medical PC, human machine interfaces, and
network security appliances.

Embedded Solutions / Single Board Computers


Aaeon
Amulet Technologies
Axiom Tek
Connect Tech
Digi International
IEI Technology
Reach Technology

T E C H N O L O G Y I N C.
LED Lighting available from Nu Horizons

LED lighting systems are composed of LEDs


OSRAM
multiple subsystems: LEDs, LED drivers,
Sharp
thermal management, and optics; each

interacting with the other to affect the Optics


LEDIL
system’s overall performance. We’ve

put together a concise team of industry Thermal Management


Cooler Master
veterans from each of the LED lighting

disciplines. Working together, the Integrated Solutions


LED Specialists
team offers comprehensive, cross-
OptoElectronix
discipline design tools and educational

opportunities. LED Driver Suppliers


Allegro Microsystems
Exar
IXYS
Linear Technology
Micrel
Sharp
STMicroelectronics
Supertex

Power Solutions available from Nu Horizons

Manufacturing Services
45,000 square-foot facility in North America

 ISO 9001 : 2000 certified
 Facility is safety certified by UL, CSA, VDE and TUV
 Product tested to comply with every known safety standard
 ATE data retention
 Expert power integration

Design Services
Modified standard product

 Add bracket / cover / cable assembly to power supply or fan
 Modular products

Standard product in custom enclosure



 Switch / circuit breakers / fuse / fans / blowers /
heat sinks / connectors / EMI filter / wire harnesses
 Simple pcb interface

Complete custom design using DC/DC modules



 Printed circuit boards design and assembly
 Built in features including: control and/or alarm circuits / monitoring /
redundancy / digital interface / hotswap
Nu Horizons Line Card

• Wireless (Bluetooth modules, ZigBee modules,
802.11 modules) • Power (MOSFET, IGBT, Diodes, Thyristors, DC/DC,
• Military Discretes (Switching Diodes - JAN, JANTX, JANTXV) PWM Control, LED/Lamp/Display Drivers)
• RF Power (FETs, Drivers, Amplifiers, Microwave
modules, RF Modules)
• Solar Devices (Solar Cells, Solar Bits, Solar Die,
Solar Battery Chargers)

• Audio (DAC’s, ADC’s, Codec’s, SPDIF, Sample Rate
Conv., DSP, USB) • Device Server Modules
• Memory (EEPROM, DAC + EEPROM) • Embedded MCU / MPU (ARM7TDMI, ARM9926EJ)
• Networking (T1/E1/T3/E3 xcvr, PCM) • Networking Modules (Wired/Wireless 802.3 /
• Sensors (Hall Effect Sensor, 3d Compass) 802.11bg / 802.15.4
• Video (NTSC/PAL Encoder/Decoder, A/V Switches, • Data Converters (Delta Sigma, SAR, Voltage DAC,
Video Gain Amp) Current DAC)
• Frequency Control (Silicon Timing)
• Interface (RS-232, 422/485, CAN PHY)
• Power Management (Switching Regulators, Linear
Regulators, DC/DC µModules, LED Drivers, Hot
Swap, PoE)
(Formerly Astec / Artesyn)
• Signal Conditioning (Amplifiers, Comparators,
• Discrete (Transistors, FET arrays, Thyristors, Triacs) Filters, Voltage References, Thermal Couple
• Display (Vacuum – Fluorescent Display Drivers) • AC-DC Switchers
- Low Power (LP, NT, DA, DP, SSL) 25W-350W Compensators)
• LED Drivers (Constant Current Drivers) • Wireless / RF (I/Q Modulators – Demodulators,
• Motor Control (Brushless DC, Bi-Polar Stepper) - Medium Power (MP) Up to 1200W
• Power (Linear Regulators, Buck/Boost/Fly back DC- - High Power (VS) Up to 2500W Up & Down Converting Mixers, IF Amplifiers, PA, RF
DC, Charge Pumps) - Intelligent High Power (iVS) Up to 4860W Log Detectors, RF Power Detector)
• Sensors (Hall Effect) • DC-DC Modules (1/16 Brick, 1/8 Brick, ¼ Brick, ½
Brick, RF Power Brick)
• Industry Standard - Non Isolated Point-of-Load
(C-Class, E-Class, F-Class)
• Power Systems Engineering Services
• Data Communications (10/100/1G/10G Ethernet
• Analog (Data Conversion, Power Management)
• Communications (Bluetooth, LIN, CAN, POTS, Switches, 10/100/1000/10G PHYs)
GPS, RF, Zigbee) • Embedded MCU / MPU (ARM V5TE, PXA
• Memory (Flash, EEPROM, Modules) StrongARM, PPC & MIPS Systems Controller)
• Microcontrollers (8051, AVR, ARM7TDMI, • Power Management (POLA)
ARM926EJ, Cortex M3) • Data Converters (ADC, DAC) • Storage (FAS/SATA/PATA, SAS/Fiberchannel,
• Multimedia & Imaging (IR, Video) • Interface (PLB / PCI / I2C / SPI / USB UARTs, Storage Processors)
• Network Storage (Data Storage) RS232/485/422 Transceivers) • Video (Format Converter)
• Programmable Logic (FPGA, SPLD/CPLD) • Power (Buck/Boost Regulator’s, Charge Pumps, • Wireless / RF (802.11 Modules)
• Sensors (Biometrics, RF, Smart Cards)
LDO’s, Supervisors, PWM, Programmable Power)
• Storage (Data Reduction, Data Security)
• Telecom (T1/E1/DS1/DS3/E3 LIU’s, Carrier ETH
SONET/SDH Framers, Mappers & Aggregators)

• Analog (Drivers / Voltage & uC Supervisors /
• Fiber Optic Devices (10G FP TOSA & MM PIN Filters / Switches / Regulators)
ROSA, OTDR FP Lasers, 2.5G DWDM DML, DFB (Fiber Optics Division) • Bus Device ICs (USB / PC / PCMCIA / SMBus)
TOSA & APD ROSA) • Ethernet (10/100/1000 PHYs, Controllers, Switches)
• Optocouplers (Transistor Output, High Speed, Solid • Optical Components (WDM Management, 850nm • Linear ICs (Active Filters / Comparators /
State Relays) VCSELs & Detectors, 1310nm Lasers & Detectors, Op Amps / References / Timers)
• RF Modules (Zigbee) CML Transmitters,WSS) • Power Management ICs (Battery, Display, Hot-
• RF Semiconductors (RFIC Switch, GaAs FET, • Optical Transceivers (GBIC, XFP, MSA300, SFP, Swap, PCI/PCIX/PCIE, High Side, LDOs, DDR)
GaAs PA, Si LD-MOSFET, CATV Hybrid, Si RFIC) • Precision Edge ICs (Clock distribution, generation,
SFP+)
• Passive Optics (WDM networks) synthesizers / Multiplexers, PLLs, buffers, CDRs)
• RF (290 – 980 ISM band / ASK/FSK / 200kbps max
data rate, RF Modules)
• System Management ICs (Fan Control / Thermal
Supervisor I2C)

• Embedded Array ( 0.13µ - 0.5µ / 6K – 10.7M
Gates / 50 – 300 MHz)
• IP Repository ( ARM926EJ, 8051, USB, PCIE, • Audio (Embedded/De-Embed)
DDR2, 10/100 MAC, Mil-STD-1553, UART, DMA, • Datacom (CDRs, Laser Drivers, TIAs, Limiting Amps,
Timer, GPIO) • DRAM (DDR3 SDRAM, DDR2 SDRAM, DDR
• Standard Cell ( 0.13µ - 0.25µ / 5M – 12M Gates / ROSA, PCIe Retimers/Redrivers/Bridges, Optical
Modules (SFP), Backplane SerDes) SDRAM, SDRAM, RLDRAM, PSRAM)
150 – 333 MHz) • DRAM Modules (FBDIMM, RDIMM, SODIMM,
• Structured ASIC ( 0.13µ - 0.35µ / 21K – 1.7M • Video (CDRs, Laser Drivers, TIAs, Limiting Amps,
Gates / 50 – 250 MHz) ROSA, PCIe Retimers/Redrivers/Bridges, Optical UDIMM)
Modules (SFP), Backplane SerDes) • Mobil DRAM (Mobil SDRAM, Mobil DDR SDRAM)
• Multichip Packages (MobilDRAM & NAND Flash
Combinations)
• NAND Flash Memory (Managed NAND, High
Speed NAND, Solid State Storage, Embedded USB)

• Power and Battery Management (IGBT and
MOSFET gate drivers)
• Sensor and Imaging Arrays (Hall Effect Sensors) • Memory (QDR/DDR SRAM, Zero-Wait SRAM
• Signal Conditioning (Solid State Relays, (NBT), Sync Burst SRAM, Specialty Sync-SRAM)
Optocouplers) (Formerly C&D Technologies)
• Telecom (Embedded Modem, MF Trunk signaling,
DTMF) • AC/DC Power Supplies (200 – 2000 Watts,
2.5VDC to 48 VDC Out – PCI Modules)
• Data Acquisition (Electronic Imaging, A/D
Converters, D/A Converters, Sample/Hold Amplifier,
Multiplexers)
• Memory (DDR DRAM,SDRAM, EDO & FPO DRAM, • DC/DC Converters (0.25 to 340 Watts, 0.02 to 80
• Imaging Solutions (Fax Modems, Fax and MFP E2PROM, PSRAM, SRAM, DDR II Synchronous Amps, 1.2 to 48 VDC Out; 3 to 75 VDC In)
System Solutions, Digital Photo Frames) SRAM, Asynchronous SRAM) • Digital Panel Meters (Voltmeters, Wire Meters,
• Audio (Speakers-on-a-Chip, PC HD-Audio, PC HD- • Smart Card (Two-Wire Serial EEPROM, Secure, Process Monitors, AC/DC Ammeters)
Audio Modem Combo) MCU Based, ICs) • Magnetics (Inductors & Transformers, Differential
• Video (MPEG Encoders/Codecs, Video Decoders, common-mode filters, Databus Isolators)
Demodulators, Surveillance / Security)
• Dial-Up Access Modems (PC Dial-Up Modems,
Embedded Dial-Up Modems)
Nu Horizons Line Card
• Power Management (AC/DC, Battery
• AC-DC Power Supplies (125W-375W, 3.3vdo to • Frequency Control (Oscillators, Crystals, VCXO, Management, DC/DC, LDO, MPU - Supervisor, PoE,
56vdo, 90-264vao in, 3”, 3.3” x 5” format) TCXO, OCXO, Sine Wave Oscillator) VDC References, AC Switches)
• DC-DC Open Frame Power Supplies (125W, • Discretes (Thyristors, Diodes, FETs, Transistors)
160W, 3.3-48vdo 3” X 5” format)
• Signal Conditioning (Comparators, Op-Amps,
Clamp Diode Arrays, Crowbar Diodes, EMI Filtering)
• Power Systems Engineering Services • Logic (3.3V, 5V, Translators, Gates, Switches, Port -
Expansion)
• Communications (CAN, LIN, ZigBee) • Sensors (Accelerometers, Proximity, Thermal, Touch)
• Discrete (Diodes, Power MOSFETS, Thyristors, • Interface (Smartcard)
Triacs, Transistors) • Wireless (Bluetooth, ZigBee, GPS, RFID)
• Embedded MCU / MPU (8/16/32 Bit MCUs) • Audio (Decoders, Power Amps, Analog CPU, Digital
• Logic (Standard – High/Low Voltage, Interface, CPU, Radio)
• Wireless/RF (2.4G / 900M / 433M Transceiver, Multi-Purpose) • Image Sensor (Camera Modules, Imaging Signal
MCU based RF, Audio streaming) • Memory (Fast Flash, Low Power SRAM, EEPROM) Processor, CMOS Arrays)
• Video (Demodulator, Decoders)
• Motor Control (Controllers, Drivers, MCU’s)
• Microcontrollers (8-bit, 16-bit, ARM7TDMI,
ARM926E, Cortex M3)
®
• Communications (Voice & Audio CODECs, Pro-X
SLICs, USB Audio Codec) • Frequency Control (Oscillators, Optical Timing
• Logic ICs (I/O Controllers, ISA Bridge, Power Clocks, Sine Wave Oscillator)
Management, Hardware Monitors, Clock Generators, • RF Components (SAW Resonators, SAW RF & IF • Optoelectronics (LED Drivers, EL Lamp Drivers)
Power I/C, Card Reader IC’s, IEEE1394) Filters, RFIC Transceivers) • Power (Switching, Automotive, PFC, Backlight,
• MPU (8-bit 80C51 based, 32-bit ARM7TDMI) • RF Modules (ZigBee, 802.15.4, UHF Mesh, FHSS LDO, High Voltage Interface / Driver’s, PoE)
• Power (ACPI Controller, PWM, DDR Bus Term, ISM, Bluetooth, 802.11b) • Transducers (Ultrasound)
Power Switch) • Standalone RF modules (FHSS, 802.15.4,
• Voice Solutions (Record & Playback ICs) 802.11b, and Bluetooth)


• AC/DC Power Supplies (Industrial and Medical -
300W - 1500W)
• DC/DC Converters
(Rohm Semiconductor is the official sales channel for Oki • Power (High Reliability Transistors) - Industry Standard (1/8-Brick, 1/4-Brick, 1/2-
Semiconductor products) Brick, Full Brick)
- Non-Isolated Point of Load
• Audio (CODECs, DACs, Amplifiers ) - Intermediate Bus Converters (1/8-Brick, 1/4-
• Display Drivers (LCD / VFD Driver / Controllers) Brick, 1/2-Brick)
• Embedded MCU / MPU (4-Bit NX 63K /
ARM7TDMI / ARM946E / Biometrics)
• Memory (P2ROM, DRAM )
• Speech (BGM Mixer - ADPCM & ADPCM2, Voice • Flat Panel Displays (LCD – 2” to 65”)
Synthesizers & Recorders, Audio Codec) • Memory (Flash – NOR)
• Telecom (ADPCM – Linear – PCMA-Law - VoIP • Data Interconnect (Signal Conditioners and
• Optoelectronics (LEDs, LED Modules, Laser Diode, Retimers, Crosspoint Switches, Backplane, Switch
Codec’s, Echo Cancellers, Transceivers) Photocoupler, IrDA, photo interrupters, Emitters/
• Video (NTSC / PAL / SECAM Encoders – Fabrics)
Detectors, Sensors) • Ethernet (10/100/1G/10G PHYs, 10/100/1G/10G
Decoders, NR-FIFO) • Power (LDO / Switching Regulators, LED Drivers, MACs, Switches, Transceivers)
Solid State Relays) • Storage (FC, SerDes, Transceivers, SAS
Controllers, SATA Controls)
• Transport Physical Layer (TIAs, Amplifiers,
Photodiodes, CDR, MUX, DEMUX, Transceivers,
PON)
• Analog Image Sensor (NTSC/PAL) • Transport Processing (VC, FEC, Network
• Digital Image Sensor (CIF, VGA, 1.3M / 2.0M / Processors, TSI, Pointer Processors)
3.2M / 5.17M Pixel)
• Image Processors • Digital Video Processors
• Storage Products (Serial ATA - Parallel ATA,
Parallel ATA Controller, RAID Storage Processors,
SATA Controllers, SATA Port Multipliers)
• Video Transport (HDMI, DVI and iTMDS Products - • Memory (SDRAM / DDR1, Pseudo SRAM, Serial
Receivers, Transmitters, Switches, PHYs) Flash, Parallel Flash)

• High-Power Laser Diodes (Single, Laser Bar /
Stacks)
• Infrared (Photo detectors, Emitters, Sensors)
• Intelligent Displays (Self-Contained LED Displays)
• LED’s (Side / Radial / Top Emitters, Arrays, High • Controllers (Flash Memory Card Controller, USB
Power) Flash Controller) • Filters
• Embedded Graphics (128-bit 2D/3D mobile • Inductors
graphics engine, Mobile Graphics Coprocessor) • Isolators
• Mobile Communication (Mobile Satellite TV Tuner • Transformers (Modem, Analog/Voice Switching,
(Including SaRonix) IC) DSL, Cable Modem, RJ45, PoE)
• Multimedia SoC (MP3/WMA Digital Audio Player,
USB 2.0 Megapixal Image Controller)
• Analog Switches (3-17V SPDT-SPST-DPST-MUX,
Custom HDMI/DVI-PCI-USB-LAN)
• Bridges (PCI, PCIX, PCI Express – 32/64Bit –
66/133MHz)
• Clock ICs ( VCXOs, Buffers, Drivers, Generators,
Skew Controllers)
• Crystals & Oscillators (Quartz Crystal Resonators) • Advanced I/O Controllers (USB-ATA, Southbridge)
• Digital Switches (2-Port, Bus, Crossbar, DDR, • Data Communications (10/100 MAC/PHY
Mux/DeMux, Low Voltage Translator) Controller, 10/100PHY, Multimedia Processors,
• Interface (Re-Drivers, Buffers, Flip-Flops, Gates, ArcNET, CircNET, USB Ethernet)
Latches, Registers, Transceivers, Voltage Translators) • Environmental (Temperature Sensors, Fan Control)
• Logic (ALVC, FCT, LCX, LPT) • USB Solutions (Card Reader, Flash Drive, Disk
• PCI Express Solutions (Packet/Signal Switches, Drive, Hub, PHY)
Bridge, PHY, Signal Conditioning, Clock-Buffers/
Generators/Crystals)
• Translators (Voltage, I/O Signal)
POWER & BATTERY MANAGEMENT SYSTEM MONITORING
Battery Management Linear Regulators & Power Management Linear Technology ST
Allegro Microsystems References Exar
Linear Technology IXYS Micrel Vitesse
Allegro Microsystems
Micrel Atmel Linear Technology SMSC
ST Exar Marvell
Linear Technology Micrel
Discretes Marvell (modules) Murata Power Solutions
Aeroflex Metelics (military) Micrel ST
Allegro Microsystems
IXYS
Oki
Sharp TIMING
Murata Power Solutions ST Power Modules
Emerson Network Power Crystals, Oscillators, Drivers, Buffers, PLLs
Renesas Supertex Linear Technology
Semicoa
ST Marvell Clock Distribution Clock Generation
Supertex Motor Control Murata Power Solutions Exar AKM Semiconductor
Allegro Microsystems SynQor Micrel Exar
Wurth Midcom
ST Pericom Linear Technology
ST Micrel
Hot Swap Switching Pericom / SaRonix
Linear Technology POE Allegro Microsystems Pletronics
Micrel Linear Technology Exar RFM
Supertex ST Linear Technology
Supertex Marvell
Micrel
Oki
ST
Supertex

POWER SUPPLIES
AC-DC DC-DC CONVERTERS CENTRAL
Low Power Industrial Isolated / Industry
Emerson Network Power Standard Bricks / A/D 8-Bit
Murata Power Solutions Non-Isolated Point of Load AKM Semiconductor Atmel
N2Power Exar ISSI
Emerson Network Power
Murata Power Solutions Linear Technology Nordic
Medium Power SynQor Murata Power Solutions Nuvoton
Emerson Network Power Nuvoton Oki
Murata Power Solutions ST Renesas
N2Power Open Frame ST
SynQor N2Power
D/A
AKM Semiconductor 16-Bit
Front End
Emerson Network Power Board Level Modules Linear Technology
Murata Power Solutions
Renesas
ST
Murata Power Solutions Intermediate Bus Converters ST
Emerson Network Power
High Power Murata Power Solutions
Emerson Network Power SynQor

Medical Memory & Processor Power


Emerson Network Power
Emerson Network Power
SynQor Murata Power Solutions SIGNAL CONDITIONING
Power Systems Engineering Services Discretes Isolation
ST CEL
Emerson Network Power
Murata Power Solutions Clare
N2Power Drivers Pericom
Nu Horizons Value-Add Micrel Sharp
ST ST
Supertex
Comparators
Amplifiers Linear Technology
OPTOELECTRONICS Linear Technology Micrel
ST
Micrel
Infrared LED Arrays / Modules ST
OSRAM OSRAM Filters
Sharp Sharp Linear Technology
Micrel
LEDs / Laser Diodes ST
Lasers OSRAM
Finisar Sharp
Optical Systems
LED Displays CEL
OSRAM Finisar
Optrex
Murata Power Solutions OptoCouplers
CEL SENSORS AND IMAGING ARRAYS
Sharp
Allegro Microsystems Omnivision
AKM Semiconductor OSRAM
Atmel Sharp
Clare SMSC
Nuvoton ST
Oki
MEMORY TELECOM WIRELESS
Non-Volatile Volatile Modem Central Office ISM ZigBee
Conexant (CODECs, SLICs, Atmel Atmel
EPROM DRAM ST Micrel CEL
Atmel
DAA, xDSL) Nordic ConnectBlue
ISSI Atmel
Oki Micron RFM Oki
VoIP Clare ST Renesas
ST Oki Conexant
Winbond Marvell RFM
Nuvoton Exar RFID ST
E2PROM Oki Nuvoton Atmel
AKM Semiconductor Oki Discretes (RF)
Atmel SRAM Renesas ST
Renesas AKM Semiconductor
ISSI Atmel ST
GSI Technology 802.11 a/b/g/n Atmel
Renesas Vitesse ConnectBlue CEL
ST ISSI Transceivers
Renesas Clare Digi IXYS
Sharp Exar Marvell LTC
Flash ST Finisar RFM Micrel
Atmel Switching Sharp RFM
Winbond Gennum Exar
ISSI Marvell ST ST
Micron Vitesse
ST
Renesas FIFO Vitesse Microwave GPS
Sharp Oki CEL Atmel
Winbond IXYS ST

Storage Controllers Bluetooth WiMax


Silicon Motion ConnectBlue Sharp
SMSC RFM

PROCESSOR DATACOM PHYSICAL LAYER


32-Bit Ethernet MAC Ethernet Switching Ethernet
Atmel Marvell Marvell Marvell
Digi Micrel Vitesse Micrel
Marvell SMSC SMSC
Nuvoton ST USB ST
Oki Renesas Vitesse
Renesas Silicon Motion
ST WAN / Transport SMSC
Exar Transformers / Isolators
Gennum Optical Wurth Midcom
Marvell Conexant
Vitesse Finisar
Gennum

BUS INTERFACE
Parallel High Speed Serial
LOGIC Nuvoton
Pericom
(above 1 MB/sec)
Gennum
Marvell
ASIC SPLD Micrel
Atmel Atmel Pericom
Chip-X Low Speed Serial
Renesas
(under 1 MB/sec) SMSC
Standard Exar
CPLD Murata Power Solutions ST
Linear Technology
Atmel Pericom Micrel
Renesas Oki
ST Renesas Level Translators
FPGA SMSC Atmel
Atmel ST Linear Technology
Micrel
DISK / INTERFACE Pericom
ST
SAS/SCSI FibreChannel
Marvell Marvell
Vitesse Vitesse
SATA/ATA
AUDIO / VIDEO Atmel
Solid State
Micron
AKM Semiconductor Oki Exar Silicon Motion
Conexant Omnivision Marvell SMSC
Gennum Silicon Image Silicon Image
Marvell Silicon Motion SMSC
Nuvoton ST Vitesse
Enhance Your Design...
With Nu Horizons Education and Development Solutions

Portal is a monthly publication containing new products, technologies and development tools
available from Nu Horizons leading suppliers. Portal is availabe both in print and on the web.
Sign up online to receive your copy, be notified of upcoming issues or to request samples of
the products found inside.
www.nuhorizons.com/portal

LabCam delivers online training opportunities in a way that recognizes the value of engineers’
time. As easily as You Tube® videos, engineers can quickly load and watch videos from industry
leaders consisting of insights on products, evaluation kit overviews, end-user applications and
more. Each tutorial is up to ten minutes in length and features technology experts, CEOs and/
or peers introducing new solutions or explaining integral aspects of an important product,
solution or application. This free value-added program is packaged for short, informative and
high quality distance learning.
www.nuhorizons.com/labcam

Nu Horizons is proud to present our education and training program, which offers engineers
the opportunity to participate in technical seminars conducted by experts focused on the
latest technologies from our leading suppliers. This program provides higher velocity
learning to help minimize start-up time to quickly begin your design process utilizing the latest
development tools, software and products. Check online for the latest seminar schedule.
www.nuhorizons.com/xpresstrack

Online Learning Nu Horizons Online Learning Center is designed to provide a complete training experience
for engineers — without having to leave the office. New supplier trainings are posted twice

Center a month and range from new product overviews to in-depth technical training and potential
design implementations. These live trainings are recorded and archived for your viewing
convenience.
www.nuhorizons.com/olc

In order to simplify the design process, Nu Horizons has created a series of application notes
Application designed to guide engineers through the process of interfacing different devices together.
Using a detailed step-by-step approach, these design guides identify key elements in the design
process. Topics in the application notes are organized by design task and each topic is a
Notes stand-alone section, with a short introduction or overview, followed by the step-by-step design
guidelines. All steps include a sufficient level of detail to provide the designer with relevant
information to proceed quickly and easily from start to finish.
www.nuhorizons.com/appnotes

Development Nu Horizons offers a wide range of development / evaluation boards, tools and kits featuring
the latest technology from the most trusted suppliers in the industry. Visit the development
Tools tool section of our website for a variety of solutions all aimed at providing a low-cost solution
for designers to accelerate a product’s time-to-market.

www.nuhorizons.com/devtools

Das könnte Ihnen auch gefallen