Beruflich Dokumente
Kultur Dokumente
Hardware Description
5-1
5-2
Issue 03 (2007-10-25)
Appearance
The C-type PDU is front accessible, used in the DC-powered front-access cabinet. Figure 5-1
shows the C-type PDU.
Figure 5-1 C-type PDU
Function
The PDU provides four 48 VDC output ports.
Issue 03 (2007-10-25)
5-3
SW1
NEG2 (-)
1
1
SW2
1
SW3
RTN1 (+)
1
1
2
RTN2 (+)
2
2
2
2
2
3
3
3
3
Front Panel
Figure 5-3 shows the front panel of the C-type PDU.
Figure 5-3 Front panel of the C-type PDU
Output terminal
ON
ON
ON
OFF
OFF
OFF
SW1
SW2
NEG1()
RTN1(+)
SPD
INPUT
MONITOR PORT
Monitoring parameter
output terminal
SW3
PGND
PGND terminal
RTN2(+)
NEG2(-)
Channel 2 input
terminal
Surge protection
board
Input Terminal
Figure 5-4 shows the input terminals of the C-type PDU.
5-4
Issue 03 (2007-10-25)
The C-type DC PDU provides two 48 VDC inputs or one 48 VDC input.
When the PDU provides two 48 VDC inputs, the input terminals are connected as follows:
l
When the PDU provides one 48 VDC input, the input terminals are connected as follows:
l
When the PDU provides one 48 VDC input, input terminals NEG1 (-) and NEG2 (-) shall be connected
with the short-circuit piece. You can select any input terminal to connect to the power input.
Output Terminal
Figure 5-5 shows the output terminals of the C-type PDU.
Issue 03 (2007-10-25)
5-5
ON
ON
ON
OFF
OFF
OFF
SW1
SW2
NEG1(-)
RTN1(+)
SPD
INPUT
MONITOR PORT
ESC(-) ESC(+)
1-
SW3
1+
2-
PGND
RTN2(+)
2+
3-
NEG2(-)
3+
In Figure 5-5:
l
Output terminals "ESC (-)" and "ESC (+)" provide power directly to the ESC.
ON
ON
ON
OFF
OFF
OFF
SW1
SW2
SW3
Table 5-1 shows the mapping between the output tributary switches and the output terminals.
Table 5-1 Mapping between the output tributary switches and the output terminals
5-6
Terminal Tributary
SW1
SW2
SW3
Issue 03 (2007-10-25)
NOTE
"ESC (-)" and "ESC (+)" have no corresponding output tributary switches.
LED
The LED of the PDU is on the lightning proof board, as shown in Figure 5-8.
Figure 5-8 LED on the lightning proof board
Issue 03 (2007-10-25)
Area
Silk
Screen
Meaning
Color
Status Description
Lightning
proof board
SPD
INPUT
Working status
of the lightning
proof board
Red
5-7
Specifications
Table 5-3 lists the specifications of the C-type PDU.
Table 5-3 Specifications of the C-type PDU
Item
Specifications
Dimensions (W x D x H)
80 A
Appearance
Figure 5-9 shows the H-type PDU.
Figure 5-9 H-type PDU
Function
The PDU has the following functions:
5-8
Issue 03 (2007-10-25)
Display the status of four power inputs and the status of the lightning arrester.
NEGA (-)
Upper
half
SW1
SW2
NEGB (-)
NEG11
NEG12
RTN11
RTN12
NEG21
NEG22
RTN21
Lower
half
NEGC (-)
Input D
SW3
NEG31
SW4
NEGD (-)
RTN22
NEG32
RTN31
RTN32
NEG41
Return A
Return D
NEG42
RTNA/B (+)
RTN41
RTNC/D (+)
RTN42
Figure 5-11 Power supply principles (four inputs) of the H-type PDU
Input A
Input B
NEG11
NEGA (-)
Upper
half
SW1
RTN11
SW2
NEGB (-)
NEG12
RTN12
NEG21
NEG22
RTN21
Input C
Input D
Lower
half
NEGC (-)
SW3
NEG31
SW4
NEGD (-)
RTN22
NEG32
RTN31
RTN32
NEG41
Return A and B
Return C and D
Issue 03 (2007-10-25)
RTNA/B (+)
RTNC/D (+)
NEG42
RTN41
RTN42
5-9
Front Panel
Figure 5-12 shows the front panel of the H-type PDU.
Figure 5-12 Front panel of the H-type PDU
Monitoring parameter
Output terminals
output terminal
Input Terminal
Figure 5-13 shows the input terminals of the H-type PDU.
Figure 5-13 Input terminals of the H-type PDU
5-10
Input Terminal
Meaning
Two inputs
Issue 03 (2007-10-25)
Input Terminal
Meaning
Four inputs
PGND terminal
NOTE
Distributed power supply: Each power input serves part of the shelves in the cabinet. For example,
input 1 powers shelves 1 and 2; while input 2 powers shelf 3.
A, B, C and D stands for NEGA (-), NEGB (-), NEGC (-) and NEGD (-) respectively.
Output Terminal
The PDU provides eight outputs, as shown in Figure 5-14.
Table 5-5 shows the mapping between the output terminals, control switches and service shelves.
Figure 5-14 Power output terminals on the H-type PDU
NEG11 (-)
NEG22(-)
NEG31 (-)
NEG32(-)
NEG22(-)
NEG42(-)
NEG41(-) NEG42(-)
5-11
Table 5-5 Mapping between the 48 V output terminals, tributary switches and service shelves
Terminal Silk Screen
Meaning
Control Switch
SW1
NEG41(-), RTN41(+)
SW2
SW3
SW4
5-12
Issue 03 (2007-10-25)
Meaning
Status Description
PWRA
PWRB
PWRC
PWRD
Issue 03 (2007-10-25)
5-13
Silk Screen
Meaning
Status Description
SPD
Specifications
Table 5-7 lists the specifications of the H-type PDU.
Table 5-7 Specifications of the H-type PDU
Item
Specifications
Dimensions (W x D x H)
483 mm x 380 mm x 87 mm
120 A (48 V)
Function
The AC-powered cabinet uses the Mini4820 AC power module to convert the 220/110 VAC
into 48 VDC and then distribute the power to each load.
Appearance
Figure 5-18 shows the Mini4820 AC power module.
Figure 5-18 Appearance of the Mini4820 AC power module
Input Terminals
Figure 5-19 shows the input terminals of the Mini4820 AC power module.
5-14
Issue 03 (2007-10-25)
Output Terminals
Figure 5-20 shows the output terminals of the Mini4820 AC power module.
Figure 5-20 AC output terminals of the Mini4820 AC power module
Communication
connection terminal
Battery connection
terminal
Table 5-8 describes the output terminals of the Mini4820 AC power module.
Table 5-8 Output terminals of the Mini4820 AC power module
Terminal Silk
Screen
Meaning
Remarks
LOAD 1
LOAD 2
BATT
Battery connection
terminal
COM
Communication
connection terminal
Specifications
Table 5-9 lists the power specifications of the Mini4820 AC power module.
Table 5-9 Power specifications of the Mini4820 AC power module
Issue 03 (2007-10-25)
Power Module
Item
Specification
Mini4820 power
module
Power supply
AC power supply
Rated voltage
220 V
5-15
Power Module
Item
Specification
Voltage range
Maximum input
current
10 A
Frequency range
50 Hz (45 Hz to 65 Hz)
Appearance
The J1-type PDU is rear accessible, used in the DC-powered rear access cabinet. Figure 5-21
shows the J1-type PDU.
Figure 5-21 J1-type PDU
Function
The J1-type PDU is used in the DC-powered J1 cabinet to distribute 48 VDC.
5-16
Issue 03 (2007-10-25)
-48V3
BGND1
NEG2(-)
-48V2
BGND1
DCSW1
-48V1
BGND1
RTN1(+)
RTN2(+)
PGND
Front Panel
Figure 5-23 and Figure 5-24 shows the panels of the J1-type PDU.
Figure 5-23 Front panel of the J1-type PDU
DC DC
SW2 SW1
RTN1(+)
NEG2(-)
RTN2(+)
Input terminal
PGND
PGND terminal
5-17
Meaning
Input Terminals
PGND terminal
Output Terminals
Input Terminal
Figure 5-25 shows the input terminals of the J1-type PDU.
Figure 5-25 Input terminals of the J1-type PDU
The J1-type DC PDU supports one 48 VDC input. Its connections are as follows:
l
In Figure 5-25, NEG1(-) and NEG2(-) are connected internally, and so are RTN1(+) and RTN2(+). You
can select any input terminal to connect to the power input.
Output Terminal
Figure 5-26 shows the output terminals of the J1-type PDU.
5-18
Issue 03 (2007-10-25)
DCSW1
Table 5-11 shows the mapping between the output tributary switches and the loading tributaries.
Table 5-11 Mapping between the output tributary switches and the loading tributaries
Output Tributary Switch
Loading Tributary
SW1
48V1/BGND, 48V2/BGND
SW2
48V3/BGND, 48V4/BGND
Specifications
Table 5-12 shows the specifications of the J1-type PDU.
Issue 03 (2007-10-25)
5-19
Specification
Dimensions (W x D x H)
436 mm x 310 mm x 86 mm
80 A
Overview
The rear access EMU monitors the environment parameters of the overall system (smoke, water,
door-status, MDF, temperature, and humidity), and provide extension monitoring ports.
Front Panel
Figure 5-28 shows the front panel of the rear access EMU.
Figure 5-28 Front panel of the rear access EMU
ESC ALARM BOX
RUN
ON
OFF
NOTE
The rear access EMU can use H303ESC or H304ESC as the environment monitoring board. In Figure
5-28, the environment monitoring board is H303ESC.
Figure 5-29 shows the rear panel of the rear access EMU.
Figure 5-29 Rear panel of the rear access EMU
H301ESIB
JTA2
JTA1
JTA4
JTA3
JTA6
JTA5
JTD4
JTD3
JTD2
SIO1
JTD1
JTD8
JTD7
JTD6
JTD5
JTD12
JTD11
JTD10
JTD9
RSP/PV8
JP2
JC2
JC1
JC4
JC3
JP1
JP3
JAK1 JAK2 JAB1JAK4 JAC1 JAC2 JTM1 JTP1 JTD17
Issue 03 (2007-10-25)
Status Description
RUN
Blinking at an interval of 1s
Function Description
Buzzer switch
ON
OFF
Terminal Blocks
Table 5-15 describes the terminal blocks of the rear access EMU.
Table 5-15 Terminal blocks of the rear access EMU
Identification
H303ESC
Function
H304ESC
Function
Remarks
JTD1JTD12
Used to monitor
the PDU, fan tray
and other digital
parameters.
Connected to the
monitored devices
according to the
application
scenarios.
For H304ESC,
JTD13 connects
with the water
sensor.
JTD13
Issue 03 (2007-10-25)
5-21
5-22
Identification
H303ESC
Function
H304ESC
Function
Remarks
JTD14JTD16
Not available in
H304ESC (reserved
for special usage)
Not availabel in
H304ESC.
JTD17JTD20
Connected to the
detected -48 V power
supply.
JAC1
Relay output
JAC2
Relay output
Reserved.
JAK1, JAK2
Connected to the
alarm components,
such as the row,
column alarm LEDs.
JAK4
JTM1
Connected to the
door-status sensor.
JAB1
Connected to the
buzzer on the
cabinet.
JTP1
Connected to the
alarm unit on the
MDF.
JTA1JTA3
Connected to the
external sensor,
and outputs the 4
20 mA current or
the 05 V voltage.
Issue 03 (2007-10-25)
Identification
H303ESC
Function
H304ESC
Function
Remarks
JTA4JTA6
Not availabel in
H304ESC
Connected to the
external sensor,
and outputs the 4
20 mA current or
the 05 V voltage.
In H303ESC,
JTA4JTA6 are
connected to the
analog sensors.
Not availabel in
H304ESC.
FAN
Connected to the
power port on the
controlled fan.
BGND, 48 V
Power input
Power input
Connected to the DC
busbar.
GND
Communication
ground
Communication
ground
RSP/PV8
RJ-45 port.
Connected with
the
communication
port on the active
control board.
RJ-45 port.
Connected with
the
communication
port on the
standby control
board.
RJ-45 port.
Connected to the
supported primary
power supply
device.
Transparent
transmission port,
working in the
RS-232 or RS-422
mode.
Transparent
transmission port,
working in the
RS-232 or RS-422
mode.
RJ-45 port.
Connected to the
device that needs
transparent
transmission.
SIO2
SIO1
SIO3
Issue 03 (2007-10-25)
5-23
Specifications
The dimensions of the EMU are 436 mm (W) x 296.7 mm (D) x 86.1 mm (H).
Overview
The front access EMU monitors the environment parameters of the overall system (smoke, water,
door-status, MDF, temperature, and humidity), and provide extension monitoring ports.
Front Panel
Figure 5-30 shows the front panel of the front-access EMU.
Figure 5-30 Front panel of the front-access EMU
NOTE
The front access EMU can use H303ESC or H304ESC as the environment monitoring board. In Figure
5-30, The environment monitoring board is H303ESC.
The front panel has one running LED and one buzzer switch.
Table 5-16 describes the running LED.
Table 5-16 Description of the running LED
Item
Status Description
RUN
Blinking at an interval of 1s
5-24
Item
Function Description
Buzzer switch
ON
Item
Function Description
OFF
Terminal Blocks
Table 5-18 describes the terminal blocks of the front access EMU.
Table 5-18 Terminal blocks of the front access EMU
Identification
H303ESC
Function
H304ESC
Function
Remarks
JTD1JTD12
Used to monitor
the PDU, fan tray
and other digital
parameters.
Connected to the
monitored devices
according to the
application
scenarios.
For H304ESC,
JTD13 connects
with the water
sensor.
Not availabel in
H304ESC.
JTD13
JTD14JTD16
Issue 03 (2007-10-25)
Not available in
H304ESC (reserved
for special usage)
JTD17JTD20
Connected to the
detected -48 V power
supply.
JAC1
Relay output
JAC2
Relay output
Reserved.
5-25
Identification
H303ESC
Function
H304ESC
Function
Remarks
JAK1, JAK2
Connected to the
alarm components,
such as the row,
column alarm LEDs.
JAK4
JTM1
Connected to the
door-status sensor.
JAB1
Connected to the
buzzer on the
cabinet.
JTP1
Connected to the
alarm unit on the
MDF.
JTA1JTA3
Connected to the
external sensor,
and outputs the 4
20 mA current or
the 05 V voltage.
Connected to the
external sensor,
and outputs the 4
20 mA current or
the 05 V voltage.
In H303ESC,
JTA4JTA6 are
connected to the
analog sensors.
Not availabel in
H304ESC.
JTA4JTA6
5-26
Not availabel in
H304ESC
FAN
Connected to the
power port on the
controlled fan.
BGND, 48 V
Power input
Power input
Connected to the DC
busbar.
Issue 03 (2007-10-25)
Identification
H303ESC
Function
H304ESC
Function
Remarks
GND
Communication
ground
Communication
ground
RSP/PV8
RJ-45 port.
Connected with
the
communication
port on the active
control board.
RJ-45 port.
Connected with
the
communication
port on the
standby control
board.
RJ-45 port.
Connected to the
supported primary
power supply
device.
Transparent
transmission port,
working in the
RS-232 or RS-422
mode.
Transparent
transmission port,
working in the
RS-232 or RS-422
mode.
RJ-45 port.
Connected to the
device that needs
transparent
transmission.
SIO2
SIO1
SIO3
Issue 03 (2007-10-25)
5-27
S6
ON
S5
OFF
123
1234
S7
S1
S2
S10
S3
S8
ON
S11
OFF
D1
The DIP switch S6 is used to set the types of external analog sensors. Table 5-19 describes the
meanings and settings of S6.
Table 5-19 Meanings and settings of H303ESC S6
DIP Switch
Setting
Meaning
Default
Settings
S6-1 to S6-6
ON
ON
OFF
Reserved
No meaning
S6-7 to S6-8
The DIP switch S7 is used to set the reporting mode and ratio. Table 5-20 describes the meanings
and settings of S7.
Table 5-20 Meanings and settings of H303ESC S7
DIP Switch
Setting
Meaning
Default
Settings
S7-1
ON
ON
OFF
ON
OFF
Reserved
No meaning
S7-2
S7-3
5-28
ON
ON
Issue 03 (2007-10-25)
DIP Switch
Setting
Meaning
Default
Settings
S7-4
ON
ON
OFF
Jumpers S1, S2, S3, S8 and S10 are used to set the type of the serial port, and their settings are
described in Table 5-21.
Table 5-21 Settings of H303ESC S1S3, S8 and S11
Jumper
Setting
Meaning
Default
Settings
S1
12 connected
2-3 connected
2-3 connected
1-2 connected
2-3 connected
23 of S2 connected; 12 of
S8 and S10 connected
S2
S3, S8,
S10
2-3 connected
12 of all
jumpers
connected
S11 is used to set whether the running LED on the front panel is valid, as described in Table
5-22.
Table 5-22 Settings of H303ESC S11
Issue 03 (2007-10-25)
Jumper
Setting
Meaning
Default
Settings
S11
1-2
connected
1-2
connected
2-3
connected
5-29
S9
12 3 4
S2
S4
S5
S6
S7
S8
O N
12345678
OFF
12 3
D6
O N S3 OFF
The DIP switch S2 is used to set the types of external analog sensors. Table 5-23 describes the
meanings and settings of S2.
Table 5-23 Setting of H304ESC S2
DIP Switch
Setting
Meaning
Default
Settings
S2-1
ON
OFF
OFF
ON
OFF
ON
OFF
Reserved
No meaning
S2-2
S2-3
S2-4
OFF
OFF
The DIP switch S3 is used to set the reporting mode and ratio. Table 5-24 describes the settings
of S3.
5-30
Issue 03 (2007-10-25)
Setting
Meaning
Default
Settings
S3-1
ON
ON
OFF
ON
OFF
S3-3
Reserved
No meaning
S3-4
ON
OFF
OFF
Reserved
No meaning
S3-2
S3-5 to S3-8
OFF
Jumpers S4S8 are used to set the type of the serial port, and their settings are described in
Table 5-25.
Table 5-25 Settings of H304ESC S4S8
Jumper
Setting
Meaning
Default
Settings
S4
1-2 connected
1-2 connected
2-3 connected
1-2 connected
2-3 connected
23 of S7 connected; 12 of S6
and S8 connected
23 of S7 and S8 connected; 1
2 of S6 connected
S5
S6S8
Issue 03 (2007-10-25)
1-2 connected
23 of S7
connected; 1
2 of S6 and S8
connected
5-31
Specifications
The dimensions of the EMU are 436 mm (W) x 307 mm (D) x 42 mm (H).
Function
The AC-powered cabinet uses the GEPS4845 AC power module to convert the 220/110 VAC
into 48 VDC and then distribute the power to each load. The GEPS4845 AC power module
can connect to two sets of batteries.
NOTE
Both the rectifier units of GEPS4845 and the two sets of batteries work in the loading sharing mode, hot
backup with each other.
Front Panel
Figure 5-33 shows the front panel of the GEPS4845.
Figure 5-33 Front panel of the GEPS4845 AC power module
AC input switch
Battery
control switch
AC INPUT
COM
B1 B2
MS
++
PSM-B9
AC-L AC-N
BATT.(-)
LOAD(-)
BATT.(+)
HRS1150-9000
HRS1150-9000
HRS1150-9000
LOAD(+)
Monitoring unit
Rectifier unit
Table 5-26 describes the front panel of the GEPS4845 AC power module.
Table 5-26 Front panel of the GEPS4845 AC power module
5-32
Item
Description
Issue 03 (2007-10-25)
Item
Description
Monitoring unit
Rectifier unit
Input Terminals
Figure 5-34 shows the input terminals of the GEPS4845 AC power module.
Figure 5-34 Input terminals of the GEPS4845 AC power module
ALM
BA
TT
AC INPUT
LOAD1
LOAD2
LOA
D3
RUN
ALM
FAN-ALM
RUN
ALM
FAN-ALM
RUN
ALM
FAN-ALM
RUN
LOAD
4
COM
B
1
B
2
MS
+ +
B
AC-L
PSM-B5
AC-N
BATT.
(-)
AC-L
LOAD
(-)
BATT.(
+)
HRS850-9000C
HRS850-9000C
HRS850-9000C
LOAD(
+)
AC-N
The GEPS4845 AC power module supports one 220/110 VAC input and the connection of the
power module is as follows:
l
Output Terminals
Figure 5-35 shows the output terminals of the GEPS4845 AC power module.
Issue 03 (2007-10-25)
5-33
BA
TT
AC INPUT
LOAD1
LOAD2
LOA
D3
RUN
ALM
FAN-ALM
RUN
ALM
FAN-ALM
RUN
ALM
FAN-ALM
RUN
LOAD
4
COM
B
1
B
2
MS
+ +
B
AC-L
HRS850-9000C
PSM-B5
AC-N
BATT.
(-)
LOAD
(-)
BATT.(+
)
1- 2- 3B1
HRS850-9000C
HRS850-9000C
LOAD(+
)
B2
4-
4-
B 2- 3-
BATT.(-)
LOAD(-)
BATT.(+)
LOAD(+)
Figure 5-36 shows the output tributary switches of the GEPS4845 AC power module.
Figure 5-36 Output tributary switches of the GEPS4845 AC power module
ALM
BA
TT
AC INPUT
LOAD1
LOAD2
LOA
D3
RUN
ALM
FAN-ALM
RUN
ALM
FAN-ALM
RUN
ALM
FAN-ALM
RUN
LOAD
4
COM
B
1
B
2
MS
+ +
B
AC-L
HRS850-9000C
PSM-B5
AC-N
BATT.
(-)
LOAD
(-)
BATT.(
+)
HRS850-9000C
HRS850-9000C
LOAD(+
)
AC INPUT
BATT
LOAD1
LOAD2
LOAD3
LOAD4
5-34
Issue 03 (2007-10-25)
Table 5-27 Mapping between the output tributary switches and the loading tributaries
Output Tributary Switch
Loading Tributary
BATT
LOAD1
LOAD2
LOAD3
LOAD4
Specifications
Table 5-28 lists the specifications of the GEPS4845 AC power module.
Table 5-28 Specifications of the GEPS4845 AC power module
Item
Specification
Dimensions (W x D x H)
Output current
BATT: 63 A
LOAD1: 10 A
LOAD2: 20 A
LOAD3: 20 A
LOAD4: 50 A
Function
The AC-powered cabinet uses the GEPS4860 AC power module to convert the 220 VAC into
48 VDC and then distribute the power to each load. The GEPS4860 AC power module can
connect to two sets of batteries.
Front Panel
Figure 5-37 shows the front panel of the GEPS4860 AC power module.
Issue 03 (2007-10-25)
5-35
AC input switch
Battery
control switch
AC INPUT
COM
B1 B2
MS
++
PSM-B9
AC-L AC-N
BATT.(-)
LOAD(-)
BATT.(+)
HRS1150-9000
HRS1150-9000
HRS1150-9000
LOAD(+)
Monitoring unit
Rectifier unit
Table 5-29 describes the front panel of the GEPS4860 AC power module.
Table 5-29 Front panel of the GEPS4860 AC power module
Item
Description
Monitoring unit
Rectifier unit
Input Terminals
Figure 5-38 shows the input terminals of the GEPS4860 AC power module.
5-36
Issue 03 (2007-10-25)
AC INPUT
COM
B1 B2
B
AC-L
MS
++
HRS1150-9000
PSM-B9
AC-N
BATT.(-)
LOAD(-)
BATT.(+)
HRS1150-9000
HRS1150-9000
LOAD(+)
AC-L AC-N
The GEPS4860 AC power module supports one 220 VAC input and the connection of the power
module is as follows:
l
Output Terminals
Figure 5-39 shows the output terminals of the GEPS4860 AC power module.
Figure 5-39 Output terminals of the GEPS4860 AC power module
ALM RUN
AC INPUT
COM
B1 B2
AC-L
MS
++
PSM-B9
AC-N
BATT.(-)
LOAD(-)
BATT.(+)
B1 B2
1- 2- 3B 2- 3-
BATT.(-)
HRS1150-9000
HRS1150-9000
HRS1150-9000
LOAD(+)
+ + +
4- 4-
LOAD(-)
+ + +
BATT.(+)
+ +
LOAD(+)
Figure 5-40 shows the output tributary switches of the GEPS4860 AC power module.
Issue 03 (2007-10-25)
5-37
AC INPUT
COM
B1 B2
AC-L
MS
++
HRS1150-9000
PSM-B9
AC-N
BATT.(-)
LOAD(-)
BATT.(+)
HRS1150-9000
HRS1150-9000
LOAD(+)
AC INPUT
Loading Tributary
BATT
LOAD1
LOAD2
LOAD3
LOAD4
Specifications
Table 5-31 shows the specifications of the GEPS4860 AC power module.
Table 5-31 Specifications of the GEPS4860 AC power module
5-38
Item
Value
Dimensions (W x D x H)
Issue 03 (2007-10-25)
Item
Value
Output current
BATT: 63 A
LOAD1: 10 A
LOAD2: 20 A
LOAD3: 20 A
LOAD4: 50 A
Function
The SPD27SZ lightning arrester has the over-voltage protection function against lightning. It
can protect the power supply device and the powered device. The SPD27SZ lightning arrester
is used in the 220 VAC-powered outdoor cabinet.
Front Panel
Figure 5-41 shows the front panel of the SPD27SZ lightning arrester.
Figure 5-41 Front panel of the SPD27SZ lightning arrester
HUAWEI
SPD27SZ-MH
Single Phase Lightning Protection Box
Work indicator
Failure indicator
L/PE
N/PE
L/N
!
Danger! High Voltage
LEDs
Table 5-32 describes the LEDs on the front panel of the SPD27SZ lightning arrester.
Issue 03 (2007-10-25)
5-39
Table 5-32 LEDs on the front panel of the SPD27SZ lightning arrester.
LED
Status Description
All green
All red
Failure
LED
Green
Red
Green
Red
Green
Red
L/PE
N/PE
L/N
NOTE
When the mains over-voltage protection circuit is started for the lightning arrester, the lightning protection
function of the lightning arrester still works and the green working LED is still on. Replace the whole
lightning arrester if any of the three failure LEDs turns red.
Electrical Connections
Figure 5-42 shows the electrical connections of the SPD27SZ lightning arrester.
5-40
Issue 03 (2007-10-25)
N out
L out
N in
Lin
LED PCB
SPD
Alarm
Grounding bar
Contaction
Alarm
PE
RELAY
N out
Lout
Input terminal
Nin L in
Output terminal
Specifications
Table 5-33 shows the specifications of the SPD27SZ lightning arrester.
Table 5-33 Specifications of the SPD27SZ lightning arrester
Issue 03 (2007-10-25)
No.
Item
Input
feature
Technical Requirement
Input rated voltage
220 VAC
47 Hz to 53 Hz
220 V50 V
30 A
Output
feature
Output voltage
220 V50 V
Lightning
protection
index
Normal nominal
discharge current In
40 kA
Maximum impact
throughput capacity Imax
65 kA
5-41
No.
Item
Technical Requirement
Residual voltage Ur (8/20
s, 20 kA)
1200 V
Overvoltage
protection
Over-voltage protection
point
277.5 V2.5 V
Return difference
5 V to 10 V
Alarm
function
Function
The SPD28SZ lightning arrester has the over-voltage protection function against lightning. It
can protect the power supply device and the powered device. The SPD28SZ lightning arrester
is used in the 220 VAC-powered indoor cabinet.
Front Panel
Figure 5-43 shows the front panel of the SPD28SZ lightning arrester.
5-42
Issue 03 (2007-10-25)
HUAWEI
SPD28SZ-LA
Single Phase Lightning Protection Box
working indicator
failure indicator
!
Danger! High Voltage
Green=normal Red=fault
LEDs
Table 5-34 describes the LEDs on the front panel of the SPD28SZ lightning arrester.
Table 5-34 LEDs on the front panel of the SPD28SZ lightning arrester.
LED
Status Description
Working LED
Green
Red
OFF
Red
Failure LED
NOTE
When the mains over-voltage protection circuit is started for the lightning arrester, the lightning protection
function of the lightning arrester still works and the green working LED is still on. When the failure LED
is red, replace the lightning arrester in time.
Electrical Connections
Figure 5-44 shows the electrical connections of the SPD28SZ lightning arrester.
Issue 03 (2007-10-25)
5-43
PE
Grounding
bar
Input terminal
Output terminal
SPD
Alarm
SPD
Specifications
Table 5-35 shows the specifications of the SPD28SZ lightning arrester.
Table 5-35 Specifications of the SPD28SZ lightning arrester
No.
Item
Input feature
220 VAC
50 Hz 3 Hz
220 x (130%) V
30 A
Output feature
Output voltage
220 x (130%) V
Lightning
protection index
20 kA
Maximum impact
throughput capacity Imax
40 kA
1300 V
Over-voltage protection
point
275 V5 V
Return difference
5 V to 10 V
5-44
Technical Requirement
Over-voltage
protection
Issue 03 (2007-10-25)
No.
Item
Technical Requirement
Alarm function
Function
The SPD32SZ lightning arrester has the over-voltage protection function against lightning. It
can protect the power supply device and the powered device. The SPD32SZ lightning arrester
is used in the 110 VAC-powered indoor cabinet.
Front Panel
Figure 5-45 shows the front panel of the SPD32SZ lightning arrester.
Figure 5-45 Front panel of the SPD32SZ lightning arrester
HUAWEI
SP D32S Z
Single Phase Lightning Protection Box
OPEN
N/-L-PE
L/N-PE
L/N
ON
OFF
LEDs
Table 5-36 describes the LEDs on the front panel of the SPD32SZ lightning arrester.
Issue 03 (2007-10-25)
5-45
Table 5-36 LEDs on the front panel of the SPD32SZ lightning arrester.
LED
Status Description
Working LED
Green
Red
OFF
Red
Failure LED
NOTE
When the mains over-voltage protection circuit is started for the lightning arrester, the lightning protection
function of the lightning arrester still works and the green working LED is still on. When the failure LED
is red, replace the lightning arrester in time.
Electrical Connections
Figure 5-46 shows the electrical connections of the SPD32SZ lightning arrester.
Figure 5-46 Electrical connections of the SPD32SZ lightning arrester
Output terminals
Nout LoutNinLinNinLin
Public
electricity
Private
electricity
Input terminals
Nout Lout
SPD Contaction
Alarm
Alarm
Nin
Lin
SPD
PCB
Grounding
bar
PE
PE
Specifications
Table 5-37 shows the specifications of the SPD32SZ lightning arrester.
5-46
Issue 03 (2007-10-25)
Item
Input
feature
110 VAC
47 Hz to 63 Hz
110 x (130%) V
60 A
Output
feature
Output voltage
110 x (130%) V
Lightning
protection
index
Normal nominal
discharge current In
40 kA
Maximum impact
throughput capacity
Imax
65 kA
Residual voltage Ur
(8/20 s, 40 kA)
1.3 kV
Issue 03 (2007-10-25)
Technical Requirement
Alarm
function
5-47