Beruflich Dokumente
Kultur Dokumente
B ENGINE
A
SECTION
ACC
CONTENTS
PRECAUTIONS .......................................................... 2
Precautions for Supplemental Restraint System
(SRS) AIR BAG and SEAT BELT PRE-TENSIONER .................................................................. 2
ACCELERATOR CONTROL SYSTEM (KA24DE) ..... 3
Removal and Installation .......................................... 3
REMOVAL ............................................................. 3
INSTALLATION ..................................................... 3
INSPECTION AFTER INSTALLATION ................. 4
ADJUSTING ACCELETOR WIRE ........................ 4
ACC-1
PRECAUTIONS
PFP:00001
PRECAUTIONS
Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT
BELT PRE-TENSIONER
EBS009TB
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow harness connectors.
ACC-2
PFP:00001
A
EBS009PC
ACC
I
KBIA0871E
Accelerator pedal
Accelerator cable
Adjust nut
Rock nut
E-ring
Return spring
Return spring
REMOVAL
CAUTION:
When removing accelerator wire, make a mark to indicate lock nut's initial position.
1. Remove RH front seat. Refer to SE-4, "FRONT SEAT" .
2. Remove engine room RH cover. Refer to EM-12, "ENGINE ROOM COVER" .
3. Loosen accelerator cable lock nut at throttle body , and disconnect accelerator cable at throttle drum.
4. Disconnect accelerator cable at accelerator pedal and bracket.
5. Remove accelerator cable.
6. Remove accelerator pedal and bracket assembly.
7. Remove accelerator pedal from accelerator pedal bracket.
INSTALLATION
Install in reverse order of removal, paying attention to the points below.
CAUTION:
When assembling, always apply oil to each part, except to inside of cable.
Check if accelerator pedal is free from contact with other parts, and releases smoothly.
ACC-3
Check if throttle drum opens fully when accelerator pedal is fully depressed to the floor, and operates
smoothly in all process.
PBIC0406E
ACC-4
PFP:00001
A
EBS009NM
ACC
I
KBIA0872E
Accelerator pedal
Accelerator cable
Adjusting nut
Lock nut
Bracket
E-ring
Return spring
REMOVAL
CAUTION:
When removing accelerator wire, make a mark to indicate lock nut's initial position.
1. Remove accelerator cable from accelerator pedal and bracket.
2. Loosen accelerator pedal bracket lock nut, and remove accelerator pedal and bracket assembly.
3. Remove accelerator pedal from accelerator pedal.
CAUTION:
Do not remove accelerator switch (F/C).
4. Remove accelerator work unit together with accelerator cable in the following procedure.
a. Remove fuse box cover.
NOTE:
This is to check positions of mounting nuts to accelerator work unit.
b. Remove mounting nuts.
c. Disconnect harness connector to remove accelerator work unit.
5. Remove accelerator cable from accelerator work unit.
6. Remove accelerator work unit from bracket.
CAUTION:
Do not disassemble accelerator work unit.
ACC-5
When assembling, always apply oil to each part, except inside of cable.
Check if accelerator pedal is free from contact with other parts, and releases smoothly.
Check if throttle drum opens fully when accelerator pedal is fully depressed to the floor, and operates
smoothly in all process.
PBIC0406E
ACC-6
PFP:00030
A
EBS00907
ACC
Tightening torque
KA24DE
ZD30DD
EBS00908
ACC-7
ACC-8