Beruflich Dokumente
Kultur Dokumente
Welcome to Jeppesens ShipReportXL vessel reporting utility. ShipReportXL is a utility designed to be loaded on your
ships computer without the need to install any software, and to facilitate creating, submitting and organizing accurate
and complete daily At Sea and In Port reports. ShipReportXL works in conjunction with an existing installation of
Microsoft Office 2003, 2007, 2010 or 2013 on Windows XP, Vista and 7 operating systems.
When prompted to confirm that you want to paste the new files into that folder and overwrite the existing
files, confirm this action.
Select the old ShipReport application file (For example, ShipReportXL_1.5.xls) and delete this file.
Launch ShipReportXL by double-clicking on the file, ShipReportXL_1.5.3.xls.
TIP: You can create a shortcut for your desktop by right clicking on the ShipReportXL_1.5.3 file, selecting the
Create shortcut option and dragging that shortcut to your desktop.
If prompted to enable macros, click the Option button, select Enable this content and click OK.
Click the Settings button to open the Settings window.
Review the information shown and click Save & Close.
Jeppesen Proprietary
October 2014
NOTE: You must always click Save & Close when closing the Settings file for the changes you have
made to be saved. If you do not click the Save & Close button, your changes will be lost.
NOTE: This version of ShipReportXL is digitally signed. You can modify your MS Office settings to allow
for digitally signed files to enable macros automatically. Please refer to instructions in the FAQ guide if
you wish to modify your settings.
Jeppesen Proprietary
October 2014
When first using ShipReportXL, please click on the Settings button to review your setup and settings. For more
information on the Settings screen, please refer to that section at the end of this document.
NOTE: This version of ShipReportXL is digitally signed. You can modify your MS Office settings to allow
for digitally signed files to enable macros automatically. Please refer to instructions in the FAQ guide if
you wish to modify your settings.
Jeppesen Proprietary
October 2014
Jeppesen Proprietary
October 2014
NOTE: If your destination is not a port, but a location at sea, please choose the At Sea location from
the Arrival Port destination list. Kindly add additional information about your destination to the
Comments field, if desired. Please DO NOT create a new port for your location, as this will cause your
reports to fail in our shore-side system and we will need to ask for you to correct and resubmit your
report.
GENERAL INFORMATION:
At the top of each report is the GENERAL INFORMATION section. This section contain important base information about
the report, such as the event date and time plus UTC Offset (which very important), the Voyage ID, the names of the
Master and others, and general comments. You have the option of reporting all events in UTC, in which case you can set
the Offset to +0.
Jeppesen Proprietary
October 2014
Some fields are required, (denoted by an asterisk and pink colored field), and some are optional.
The Event Date & Time refer to exactly when the information recorded in this report is for. This may vary from the
actual date and time when the report is created. The ZD / UTC offset is a critical part of this report. Your reports may be
setup to capture ZD or UTC, depending on how your Settings screen is configured. The UTC time of the report is
always shown to the right of the Event Date / Time line and is an important check for you to validate that your event
date and time are correct. If in doubt about ZD / UTC offset, you can simply report the event time as UTC, and set the
Offset to +0. See Note below.
NOTE: You can leave the ZD or UTC offset to +0 if you prefer to report in UTC. Jeppesen accepts local
Date/Time with proper time zone offset or UTC reporting equally. Please utilize the method that works
best for your vessel and please be consistent and accurate with whichever method you chose.
Jeppesen Proprietary
October 2014
The actual Start of Sea Passage End of Sea Passage dates and time are set by the Event Date / Time (local) field of the
Start Sea Passage and End Sea Passage reports, respectively. The End Sea Passage date & Time should be changed
only if the scheduled arrival date & time changes. Once selected, subsequent reports for this passage will use the same
Start Sea Passage and End Sea Passage dates & times until an Arrival report is submitted). Both of these fields are
required.
The Current ETA to Next Port field is optional and is intended to capture the ETA the vessel believes it will have when
it differs from the Ordered ETA to Next Port date & time. This can be updated as often as the Master deems
appropriate, (on each report).
The Request Routing Support field is for those clients leveraging Jeppesens FleetManager toolset to facilitate
forwarding your requests for routing support to our Routing Services team. On each new report this field defaults to
No. If routing support is desired, change to Yes each time you submit a report. If your company utilizes this
functionality, your vessel management team will inform you that this is to be used. Otherwise, you can ignore this field.
DECK Tab:
The DECK tab collects information about vessel movements associated with that report. There are sections on this
screen for vessel position at the event time of the report (the date and time in the GENERAL INFORMATION section),
progress since the last report, progress since start of sea passage, balances of the passage remaining, weather and sea
conditions since the last report, and loading conditions. While many fields are not required by ShipReport, please follow
company policies when determining which fields must be completed.
Jeppesen Proprietary
October 2014
Watch Detail:
Some companies opt to use ShipReportXLs Watch Detail screen, which capture weather and sea conditions every four
hours, rather than once for each reporting period. If Watch Detail functionality is enabled for your ShipReportXL
installation, you will see that fields for entering daily weather and sea values are colored and not editable, and a Watch
Detail button is present in the WEATHER & SEA CONDITIONS and SINCE LAST EVENT sections.
NOTE: ShipReportXL supports the addition of custom fields at the bottom of certain tabs, including the
DECK tab. You may see some additional fields at the bottom of your DECK tab, if your company has
requested those fields.
Jeppesen Proprietary
October 2014
ENGINEERING Tab:
The ENGINEERING tab houses fields pertaining to vessel performance such as power, RPM and slip. While these fields
are not required by ShipReportXL, please follow company policies when determining which fields must be completed.
NOTE: ShipReportXL supports the addition of custom fields to the bottom of certain tabs, including the
ENGNEERING tab. You may see some additional fields at the bottom of your ENGINEERING tab, if your
company has requested those fields be added to your report.
Jeppesen Proprietary
October 2014
To capture fuel consumption, click on the Edit Fuel button, enter your values and click OK.
IMPORTANT NOTE: Fuel consumption is for daily consumption (since last report) only and is NOT for capturing passage
total consumption.
Jeppesen Proprietary
October 2014
TERMS Tab:
The TERMS tab is for capturing warranted performance for daily fuel and speed, as well as defining good weather
thresholds for seas and wind. After submitting terms at the beginning of a passage, these values do not need to be filled
in again for the remainder of the passage - unless they change.
CUSTOM Tab:
The CUSTOM tab may contain custom fields that have been setup for your vessel or company. Alternatively, such
custom fields may be located at the bottom of other tabs, leaving no fields to be displayed on this tab.
Jeppesen Proprietary
October 2014
EVENTS Tab:
The EVENTS tab is for recording various events at any point in a vessels operations. This section is designed to
capture spanning and single-point events, and their associated fuel consumption for both At Sea and In Port
periods. You may create multiple events on any report; however, events that span more than one reporting
period are captured on the report of the day in which the events ends.
Jeppesen builds and maintains the list of events you will see in the Event Type list. If there are events you do
not see listed that you would like to see, please contact Jeppesen to request their addition In the Events list you
will find a generic event: Other. If you must report an event that is not in the list, please use the Other
event, and in the comments section of the Add Event window, describe the nature of the event.
Jeppesen Proprietary
October 2014
Events are always recorded on the report spanning when an event ends. For example, if an event begins 6 hours
before the end of day 1 and concludes 12 hours after the start of day 2, add an event to the day 2 report, and
attribute all 18 hours of time, as well as all distance and fuel associated with the whole event on the day 2
report.
Submitting Reports:
To submit, click the Send Report button. ShipReportXL will perform a check of all fields. Some fields will not allow you
to proceed with sending the report if critical errors or omissions are detected. Some fields will warn you that the entry
fails the check but you can proceed if you insist. The No Corrections Continue button will be disabled if any critical
errors or omissions exist.
From the Send Report screen you can review and edit the list of recipients to receive XML and text based reports. Any
changes you make to the recipient list on this screen will be for this report only. If you want to make permanent
changes to the default recipient lists, please do so in the EMAIL tab of the Settings screen.
Your email settings will have been configured on the Settings screen. If ShipReportXL is configured to interface with
your email system, simply confirm the email recipient lists and press the Send Email button to submit your report. This
will submit your report in both XML and text formats, confirm submission, then save and close this report.
IMPORTANT NOTE: Microsoft Outlook must be open and running when you submit a report through
ShipReportXL.
Jeppesen Proprietary
October 2014
For users with older operating systems, you may be prompted to approve sending ShipReportXL reports through
Outlook. If so, please click Allow for each report type you submit, (text and XML):
NOTE: ShipReportXL submits each of your reports in both XML and text formats. It is essential to submit every
report in both XML and text formats.
Jeppesen Proprietary
October 2014
NOTE: If you are mid way through filling out a report and need to save the report to return to later, click
the Save & Close button. The report will be saved to the Edit Event page.
Jeppesen Proprietary
October 2014
Settings:
The Settings section contains configuration and validation information for your ShipReportXL utility. Static
information for your vessel such as vessel name, MMSI and company name, are included on every report.
The EMAIL tab is where your ShipReportXL utility is configured to submit reports by email.
On this screen you can chose whether to send emails through SMTP or MS Outlook. If you have Outlook running
and open on the computer with ShipReportXL installed, you can set this to Outlook. To use with nearly any
email system, you can configure for SMPT, select the security and port settings, and enter your SMTP service
username and password.
NOTE: If you have Outlook installed and running on the computer with ShipReportXL, you do not need to
enter the Login name and password information at the bottom of the Email tab. If you are using SMTP
and have email security enabled, then you must enter this information. You may need your
Administrator or IT support to assist with this step.
The UNITS tab allows for configuration of UOMs and formatting for position, time zone offset and other fields.
NOTE: BF is for Beaufort scale. DSS is for Douglas Sea State. Please enter BF of DSS as numbers, not
descriptions, in this field.
The VALIDATION tab is for setting acceptable ranges for some values such as speed over ground, power, fuel
consumption, and distances traveled. Setting these ranges will prompt an alert to check the values outside
specified ranges when you prepare to submit your reports.
Jeppesen Proprietary
October 2014
The LISTS tab is for configuring fuel & fluids and machinery types for capturing fuel consumption.
The ADMIN tab is for enabling special features and functionality in ShipReport. On this tab you can
find an option to enable Watch Detail, which is for reporting weather conditions every four hours,
(rather than once per reporting day).
Jeppesen Proprietary
October 2014
Solution
For Excel 2007, 2010 and 2013:
1. Click on the Office button (File in 2010).
2. Click on the Excel Options button.
3. Click on the Trust Center link in the left column.
4. Click on the Trust Center Settings button
5. Select the option to disable all macros except digitally signed macros.
6. Save and close.
For Excel 2003:
1. Click on the Office button.
2. Click on the Excel Options button.
3. In the Popular category, under Top options for working with Excel, click Show Developer tab
in the Ribbon.
4. In the Macro Settings category under Macro Settings, select the option to disable all macros
except digitally signed macros.
5. Save and close.
Question
I see the Ports file opening when I launch ShipReportXL. Is this a
problem?
Solution
This is normal behavior when using Microsoft Excel 2013. The Ports file may open, but you cannot
access it from your Windows toolbar. Please ignore this spreadsheet. When you close when you close
ShipReportXL, this spreadsheet will close too.
Question
I do not see the Port I need in the Ports list. What can I do to add it?
Solution
This is normal behavior ShipReportXL uses a standard global port list, but it does not have every
commercial port in the world, nor does it have company specific locations like lightering areas. You can
add these to your Ports list through ShipReportXL via the Ports screen button on the main
ShipReportXL screen. Use the Add window to create a new port entry by filling in all fields as
accurately as you can. Jeppesen services and products will reply on the record you create to identify
Jeppesen Proprietary
October 2014
that port for your ship and others in your fleet once you submit a report with the new port. If your
company uses a specific port code identify a missing port, please use that exact code when you create
the port entry.
Question
There is a field I would like to report that I do not see in ShipReportXL.
How do I add new fields?
Solution
Jeppesens ShipReportXL utility can be configured to include additional custom fields. Please contact
your office to put in a request for Jeppesens Professional Services team to add those fields to your
ShipReportXL utility.
Question
There is an Event I would like to report that I do not see in ShipReportXL.
How do I add new fields?
Solution
Jeppesens ShipReportXL utility can be configured to include additional events. Please contact your
office to put in a request for Jeppesens Professional Services team to add those events to your
ShipReportXL utility.
Question
I need to report an event that is not in the Events list. What can I do to
report that event immediately?
Solution
In the Events list you will find an event: Other. If you must report an event that is not in the list,
please use the Other event, and in the comments section of the Add Event window, describe the
nature of the event.
Question
I have a support / usage question not covered in this User Guide. How do I
reach Jeppesens Commercial Marine support group?
Solution
Jeppesens Commercial Marine support group is located in North America. Should you have any
technical or usage questions, you can reach Jeppesen any time at support.mps@jeppesen.com. This
way we can ensure our support team receives your inquiry and can respond in the timeliest fashion.
Jeppesen Proprietary
October 2014