Sie sind auf Seite 1von 13

PRODUCT PROFILE

BIANCO RAINSAVER MK5


RS5-INOX60PC2 - 800400

The RAINSAVERMK5 is an Automatic Rainwater / Mains Water


Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 400C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 Warranty, see installation and operating
JH754M
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if there is a
power failure.
BIA-INOX60PC

50
40

Head (m)

30
20
10
0

10

20

30

Flow (L/min)

40

50

The RS5-INOX60PC2 Package:


Bianco INOX60PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains
Changeover Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specifications BIA-INOX60PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and
constant pressure at low flows. Automatic electronic control has
built-in check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-INOX60PC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
330W
Current: 2.3 amps
Capacitor:
12 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP54
Insulation class:
F
Power cable length:
1.2 m
Net weight:
9.2 kg
Performance:
Maximum flow:
36 litres per minute (4 taps)
Maximum pressure:
320 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body
Stainless steel
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALLINOX60PC2 - 800408

The RAINSAVERMK5 is an Automatic Rainwater / Mains Water


Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart. No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 40 C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
JH754M
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if there is a
power failure.

BIA-INOX60PC

50
40

Head (m)

30
20
10
0

10

20

30

Flow (L/min)

40

50

The RS5-INOX60PC2 Package:


Bianco INOX60PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains
Changeover Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved flexible hoses
x2
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specifications BIA-INOX60PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and
constant pressure at low flows. Automatic electronic control has
built-in check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-INOX60PC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
330W
Current: 2.3 amps
Capacitor:
12 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP54
Insulation class:
F
Power cable length:
1.2 m
Net weight:
9.2 kg
Performance:
Maximum flow:
36 litres per minute (4 taps)
Maximum pressure:
320 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body
Stainless steel
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-MULTI900PC2 - 800401

The RAINSAVERMK5 is an Automatic Rainwater / Mains Water


Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 400C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an automatic back up should rain water level be too low, or if there is a
power failure.
BIA-MULTI900PC

40

Head (m)

30
20
10
0

10

20

30

40

50

Flow (L/m)

60

70

80

90

The RS5-MULTI900PC2 Package:


Bianco MULTI900PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specifications BIA-MULTI900PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-MULTI900PC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
585W
Current:
3.4 amps
Capacitor:
16 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP54
Insulation class:
F
Power cable length:
1.2 m
Net weight:
11.7 kg
Performance:
Maximum flow:
80 litres per minute (9 taps)
Maximum pressure:
352 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body
Stainless steel
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALLMULTI900PC2 - 800409

The RAINSAVERMK5 is an Automatic Rainwater / Mains Water


Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 400C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an automatic back up should rain water level be too low, or if there is a
power failure.
BIA-MULTI900PC

40

Head (m)

30
20
10
0

10

20

30

40

50

Flow (L/m)

60

70

80

90

The RS5-MULTI900PC2 Package:


Bianco MULTI900PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved flexible hoses
x2
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specifications BIA-MULTI900PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-MULTI900PC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
585W
Current:
3.4 amps
Capacitor:
16 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP54
Insulation class:
F
Power cable length:
1.2 m
Net weight:
11.7 kg
Performance:
Maximum flow:
80 litres per minute (9 taps)
Maximum pressure:
352 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body
Stainless steel
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-40UP037PC2 - 800402

The RAINSAVERMK5 is an Automatic Rainwater / Mains Water


Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 400C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an automatic back up should rain water level be too low, or if there is a
power failure.
60
50
40
30

Head (m)

20

UP-40UP037

10
0

10
0.6
Flow

20
1.2

30
1.8

40
2.4

50
3 .0

60
3.6

70
4.2

80
4.8

l/min
m3/h

The RS5-40UP037PC2 Package:


Universal 40UP037PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specifications BIA-40UP037PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-40UP037PC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
370W
Current: 2.2 amps
Capacitor:
10 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP55
Insulation class:
F
Power cable length:
1.2 m
Net weight:
7.0 kg
Performance:
Maximum flow:
50 litres per minute (5 taps)
Maximum pressure:
370 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body
Stainless steel
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALL40UP037PC2 - 800410

The RAINSAVERMK5 is an Automatic Rainwater / Mains Water


Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 400C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an automatic back up should rain water level be too low, or if there is a
power failure.
60
50
40
30

Head (m)

20

UP-40UP037

10
0

10
0.6
Flow

20
1.2

30
1.8

40
2.4

50
3 .0

60
3.6

70
4.2

80
4.8

l/min
m3/h

The RS5-40UP037PC2 Package:


Universal 40UP037PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved flexible hoses
x2
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specifications BIA-40UP037PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-40UP037PC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
370W
Current: 2.2 amps
Capacitor:
10 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP55
Insulation class:
F
Power cable length:
1.2 m
Net weight:
7.0 kg
Performance:
Maximum flow:
50 litres per minute (5 taps)
Maximum pressure:
370 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body
Stainless steel
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-60UP075PC2 - 800403

The RS5-60UP075PC2 Package:


Universal 60UP075PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 400C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an automatic back up should rain water level be too low, or if there is a
power failure.
Performance Curve
60
50
40
30

UP-60U075

Head (m)

20
10
0

10
0.6
Flow

20
1.2

30
1.8

40
2.4

50
3 .0

60
3.6

70
4.2

80
4.8

l/min
m3/h

Pressure System Pump Specifications BIA-60UP075PC2


The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-60UP075PC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
750W
Current:
4.8 amps
Capacitor:
20 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP55
Insulation class:
F
Power cable length:
1.2 m
Net weight:
11.0 kg
Performance:
Maximum flow:
60 litres per minute (6 taps)
Maximum pressure:
450 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body
Stainless steel
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALL60UP075PC2 - 800411

The RAINSAVERMK5 is an Automatic Rainwater / Mains Water


Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 400C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating manual
for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an automatic back up should rain water level be too low, or if there is a
power failure.
Performance Curve
60
50
40
30

UP-60U075

Head (m)

20
10
0

10
0.6
Flow

20
1.2

30
1.8

40
2.4

50
3 .0

60
3.6

70
4.2

80
4.8

l/min
m3/h

The RS5-60UP075PC2 Package:


Universal 60UP075PC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved flexible hoses
x2
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specifications BIA-60UP075PC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-60UP075PC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
750W
Current:
4.8 amps
Capacitor:
20 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP55
Insulation class:
F
Power cable length:
1.2 m
Net weight:
11.0 kg
Performance:
Maximum flow:
60 litres per minute (6 taps)
Maximum pressure:
450 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body
Stainless steel
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

MAX
W

,0

,0

,7

,7

,6

,6

,2

,2

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-JETCOM82MPC2 - 800404

JET - JETINOX - JETCOM

SELF-PRIMING CENTRIFUGAL PUMPS

JET 200-300

JET 151-251

ELECTRICAL DATA

The RAINSAVERMK5
is an Automatic Rainwater
/ Mains Water
P2 NOMINAL
CAPACITOR
In
Changeover Device designed to
provide automatic mains backup for
A
kW
HP
F
Vc
Pressure
Pump supply
systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
1,5
2
9
31,5
450
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
6,8-3,9
hour1,5auto restart.2
No need for float switch.
2,2

12

40

450

RainsaverMK5 General Specifications:


Maximum water temperature (mains + pump): 400C
2,2
3
8,5-4,9
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1,5
7,2
31,5
450
10001,1kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual
1,1 for details1,5
5,2-3
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
1,85

2,5

10

40

450

Operation:
The1,85
RAINSAVERMK5
supplies
clean rainwater
from a rainwater
tank
2,5
6,9-4
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if there is a
power JET
failure.
82 - JETINOX 82 - JETCOM 82
0

P
kPa

H
m

10

12

14

10

Q US gpm

16

12

Q IMP gpm
H
ft

14

50

400

300

200

160
40
120

JET 82
JET
82
JETINOX 82
JETCOM 82

30

100
80

Hs 9

20

60

8
100

10

0
0
0

0,5

1,5
0,4

0,2
10

20

2,5
0,6

30

40

3
0,8

40

50

20
3,5
1
60

Q m /h
Q l/s
Q l/min

The RS5-JETCOM82MPC2 Package:


DAB JETCOM82MPC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specifications
DAB-JETCOM82MPC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
DAB-JETCOM82MPC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
600W
Current: 3.8 amps
Capacitor:
12.5 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP55
Insulation class:
F
Power cable length:
2m
Net weight:
9.7 kg
Performance:
Maximum flow:
60 litres per minute (6 taps)
Maximum pressure:
460 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body Technopolymer
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-ALLJETCOM82MPC2 - 800412

JET - JETINOX - JETCOM

SELF-PRIMING CENTRIFUGAL PUMPS

JET 200-300

JET 151-251

ELECTRICAL DATA

P1 MAX
kW
2,0
2,0
2,7
2,7
1,6
1,6
2,2
2,2

The RAINSAVERMK5
is an Automatic RainwaterCAPACITOR
/ Mains Water
P2 NOMINAL
Changeover Device designed to InAprovide automatic mains backup for
kW
HP
F
Vc
Pressure
Pump supply
systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
1,5
2
9
31,5
450
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
1,5 restart. 2
6,8-3,9
hour auto
No need for float switch.
2,2

12

40

450

1,85

2,5

10

40

450

RainsaverMK5 General Specifications:


Maximum water temperature (mains + pump): 400C
2,2
3
8,5-4,9
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1,1
1,5
7,2
31,5
450
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual1,1for details 1,5
5,2-3
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5
clean rainwater
tank
1,85
2,5 supplies 6,9-4
- from a rainwater
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if there is a
power failure.
JET 82 - JETINOX 82 - JETCOM 82
0

P
kPa

H
m

10

12

14

10

Q US gpm

16

12

Q IMP gpm
H
ft

14

50

400

160
40

300

30

200

20

120

JET 82
JET
82
JETINOX 82
JETCOM 82

100
80

Hs 9

60

8
100

10

0
0
0

0,5

1,5
0,4

0,2
10

20

2,5
0,6

30

40

3
0,8

40

50

20
3,5
1
60

Q m /h
Q l/s
Q l/min

The RS5-JETCOM82MPC2 Package:


DAB JETCOM82MPC2 pressure system pump with auto-restart
pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Pump Stand and Cover to protect the pump from the elements
Stainless Steel 3/4 x 600mm WaterMark approved flexible hoses
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
Pressure System Pump Specifications
DAB-JETCOM82MPC2
The pump is a self-priming pressure system pump supplied wired and
ready to install. The self-priming ability provides excellent suction
capacity. Used especially for supplying water to domestic installations.
The pump is characterised by:
Automatic electronic pump control fitted and wired
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
DAB-JETCOM82MPC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
600W
Current: 3.8 amps
Capacitor:
12.5 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP55
Insulation class:
F
Power cable length:
2m
Net weight:
9.7 kg
Performance:
Maximum flow:
60 litres per minute (6 taps)
Maximum pressure:
460 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body Technopolymer
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-JH8003PMPC2 - 800405

The RS5-JH8003PMPC2 Package:


Bianco JH8003PMPC2 submersible pressure system pump with
auto-restart pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 400C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an automatic back up should rain water level be too low, or if there is a
power failure.
BIA-JH8003P

30
25

Head (m)

20
15
10
5
0

25

50

Flow (L/m)

75

100

Pressure System Pump Specifications BIA-JH8003PMPC2


The pump is a submersible pressure system pump supplied wired
and ready to install. The submersible pump is mounted inside the rain
water tank for silent operation. Used especially for supplying water to
domestic installations.
The pump is characterised by:
Automatic electronic pump control, plug and play
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
BIA-JH8003PMPC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
800W
Current:
4.0 amps
Capacitor:
16 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP68
Insulation class:
F
Power cable length:
10 m
Net weight:
5.3 kg
Performance:
Maximum flow:
80 litres per minute (8 taps)
Maximum pressure:
295 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body Treated Aluminium
Diffuser and impeller
Technopolymer
Mechanical seal Carbon/Ceramic/Nitrile

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-B42AMPC2 - 800406

The RS5-B42AMPC2 Package:


Bianco B42AMPC2 submersible pressure system pump with
auto-restart pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover Device
Bianco RAINSAVERMK5 to operate with mains pressure up to
1000 kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town
water supplies. Safe against waterborne bacteria, dezincification
and lead poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against
voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and
can be located any distance from the pump, and even inside the
rain water tank.
The RAINSAVERMK5 is an Automatic Rainwater / Mains Water
Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump): 400C
Maximum recommended continuous pump flow: 120 l/m
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
2 year Rainsaver MK5 warranty, see installation and operating
manual for details
WaterMark approved components
AS/NZS 4020 Approved for Drinking Water
Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an
automatic back up should rain water level be too low, or if there
is a power failure.
BIA-B42A

35
30

Head (m)

25
20
15
10
5
0

20

40

60

Flow (L/min)

80

100

120

Pressure System Pump Specifications BIA-B42AMPC2


The pump is a submersible pressure system pump supplied wired
and ready to install. The submersible pump is mounted inside the rain
water tank for silent operation. Used especially for supplying water to
domestic installations.
The pump is characterised by:
Automatic electronic pump control, plug and play
Automatic electronic control provides run dry protection and constant pressure at low flows. Automatic electronic control has built-in
check valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Mechanical shaft seal.
240V single phase TEFC motor with in-built auto reset thermal
overload
83mm elevated suction with algae proof slotted strainer
BIA-B42AMPC2 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
550W
Current:
4.0 amps
Capacitor:
20 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP68
Insulation class:
F
Power cable length:
10 m
Net weight:
12 kg
Performance:
Maximum flow:
105 litres per minute (10 taps)
Maximum pressure:
320 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body
Technopolymer
Diffuser and impeller
Technopolymer
Dual Mechanical seals
Carbon/Ceramic/Nitrile on motor side

Silicon Carbide/Ceramic/Nitrile on

pump side (Both in oil bath)

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

PRODUCT PROFILE
BIANCO RAINSAVER MK5
RS5-DIVERTRON1200 - 800407

The RAINSAVERMK5 is an Automatic Rainwater / Mains Water


Changeover Device designed to provide automatic mains backup for
Pressure Pump supply systems.
The RAINSAVERMK5 is designed to be installed in conjunction with
a Pressure Pump supply system that is fitted with an independent
pressure and flow controller with loss of prime protection and 24
hour auto restart.
No need for float switch.
RainsaverMK5 General Specifications:
Maximum water temperature (mains + pump):
400C
DIVERTRON
Maximum recommended
continuous
pump
flow:
120PUMPS
l/m
6 ELECTRONIC MULTISTAGE SUBMERSIBLE
Maximum recommended mains inlet pressure or pump pressure:
1000 kPa
DOMESTIC
WATER
SUPPLY
2 year Rainsaver MK5 warranty, see
installation
and
operating
manual for details
High reliability.
Submersible pressure pumps with built-in integrated
WaterMark approved components
Available with 3 or 4 impellers.
electronics, designed to automatically start and stop the pump.
Supplied Water
with 15 m power cord.
Built-in electronic
board,4020
pressure switch
and flow sensor.
AS/NZS
Approved
for Drinking
Available with screen filter or stainless steel ring for use
of suction kit.

Equipped with dry-run protection.


Built-in non return valve.
Easy to use.

Operation:
The RAINSAVERMK5 supplies clean rainwater from a rainwater tank
via an automatic pressure system pump to toilets, laundry and garden
taps in a household.
Mains water is also connected to the RAINSAVERMK5 as an automatic back up should rain water level be too low, or if there is a
power failure.

NOMINAL
HP

CABLE
LENGTH
m.

0,88

15

0,88

15

15

15

1000

1200

The RS5-DIVERTRON1200 Package:


DAB DIVERTRON1200 submersible pressure system pump with internal auto-restart pump controller
Bianco RAINSAVERMK5 automatic Rainwater / Mains Changeover
Device
Bianco RAINSAVERMK5 to operate with mains pressure up to 1000
kPa (145 psi)
Suits pump flows to 100 litres per minute
Incorporates a 24 hour automatic pump restart
WaterMark approved components for connection to town water
supplies. Safe against waterborne bacteria, dezincification and lead
poisoning
Australian owned and designed
The pump regulates flow and pressure and protects itself against voltage fluctuations and loss of water
The Bianco RAINSAVERMK5 can operate without power and can be
located any distance from the pump, and even inside the rain water
tank.
Pressure System Pump Specifications DAB-DIVERTRON1200
The pump is a submersible pressure system pump supplied wired
and ready to install. The submersible pump is mounted inside the rain
water tank for silent operation. Used especially for supplying water to
domestic installations.
The pump is characterised by:
Internal Automatic electronic pump control
Automatic electronic control provides run dry protection and constant
pressure at low flows. Automatic electronic control has built-in check
valve and auto restart.
Corrosion resistant pump body, diffuser and impeller.
Shaft seal with sand protection boot.
240V single phase TEFC motor with in-built auto reset thermal overload
DAB-DIVERTRON1200 Electrical data:
Rated Voltage:
240V
Mains frequency:
50 Hz
Power output:
750W
Current:
4.8 amps
Capacitor:
20 uF
Motor duty:
Continuous
Motor type:
Asyncronous, TEFC
Motor protection:
In-built thermal overload
Ingress protection:
IP68
Insulation class:
F
Power cable length:
15 m
Net weight:
11 kg
Performance:
Maximum flow:
95 litres per minute (9 taps)
Maximum pressure:
470 kPa
General:
Clean water temperature range:
2 350C
Materials:
Pump body Technopolymer
Diffuser and impeller
Technopolymer

Distributed by White International Pty Ltd


A.B.N. 48 000 119 380
PO BOX 304 MILPERRA LPO NSW 2214
Ph: 02 9783 6000 Fax: 02 9783 6001
HOTLINE: 1300 783 601 FAXLINE: 02 9783 6003

Distributed by White International NZ Ltd


Eastfield Estate, 15G Kerwyn Ave EAST TAMAKI
PO BOX 12704, PENROSE, AUCKLAND
Ph: 09 579 9777 Fax: 09 579 7775
HOTLINE: 0800 509 506 FAXLINE: 0800 804 344

Das könnte Ihnen auch gefallen