Beruflich Dokumente
Kultur Dokumente
series
MS-7640 (v3.x) Mainboard
G52-76401XI
Preface
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is
given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
MSI is registered trademark of Micro-Star Intl Co.,Ltd.
NVIDIA is registered trademark of NVIDIA Corporation.
ATI is registered trademark of AMD Corporation.
AMD is registered trademarks of AMD Corporation.
Intel is registered trademarks of Intel Corporation.
Windows is registered trademarks of Microsoft Corporation.
AMI is registered trademark of American Megatrends Inc.
Award is a registered trademark of Phoenix Technologies Ltd.
Sound Blaster is registered trademark of Creative Technology Ltd.
Realtek is registered trademark of Realtek Semiconductor Corporation.
JMicron is registered trademark of JMicron Technology Corporation.
Netware is registered trademark of Novell, Inc.
Lucid is trademark of LucidLogix Technologies, Ltd.
VIA is registered trademark of VIA Technologies, Inc.
ASMedia is registered trademark of ASMedia Technology Inc.
iPad, iPhone, and iPod are trademarks of Apple Inc.
Revision History
Revision
Revision History
Date
V3.0
2010/12
V3.1
Update Spec
2011/01
V3.2
For 990FXA-GD65
2011/05
Technical Support
If a problem arises with your system and no solution can be obtained from the users
manual, please contact your place of purchase or local distributor. Alternatively, please
try the following help resources for further guidance.
Visit the MSI website for FAQ, technical guide, BIOS updates, driver updates,
and other information: http://www.msi.com/service/download/
Contact our technical staff at: http://support.msi.com/
ii
MS-7640
Safety Instructions
Always read the safety instructions carefully.
Keep this Users Manual for future reference.
Keep this equipment away from humidity.
Lay this equipment on a reliable flat surface before setting it up.
The openings on the enclosure are for air convection hence protects the equipment
from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source and adjust properly 110/220V before
connecting the equipment to the power inlet.
Place the power cord such a way that people can not step on it. Do not place anything over the power cord.
Always Unplug the Power Cord before inserting any add-on card or module.
All cautions and warnings on the equipment should be noted.
Never pour any liquid into the opening that could damage or cause electrical
shock.
If any of the following situations arises, get the equipment checked by service
personnel:
The equipment does not work well or you can not get it work according to Users
Manual.
iii
Preface
Preface
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Notice 1
The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to comply
with the emission limits.
VOIR LA NOTICE DINSTALLATION AVANT DE RACCORDER AU RESEAU.
Micro-Star International
MS-7640
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference that may
cause undesired operation.
iv
MS-7640
DEUTSCH
Hinweis von MSI zur Erhaltung und Schutz unserer Umwelt
Gem der Richtlinie 2002/96/EG ber Elektro- und Elektronik-Altgerte drfen Elektro- und Elektronik-Altgerte nicht mehr als kommunale Abflle entsorgt werden. MSI
hat europaweit verschiedene Sammel- und Recyclingunternehmen beauftragt, die in
die Europische Union in Verkehr gebrachten Produkte, am Ende seines Lebenszyklus
zurckzunehmen. Bitte entsorgen Sie dieses Produkt zum gegebenen Zeitpunkt ausschliesslich an einer lokalen Altgertesammelstelle in Ihrer Nhe.
FRANAIS
En tant qucologiste et afin de protger lenvironnement, MSI tient rappeler ceci...
Au sujet de la directive europenne (EU) relative aux dchets des quipement lectriques et lectroniques, directive 2002/96/EC, prenant effet le 13 aot 2005, que les
produits lectriques et lectroniques ne peuvent tre dposs dans les dcharges ou
tout simplement mis la poubelle. Les fabricants de ces quipements seront obligs de
rcuprer certains produits en fin de vie. MSI prendra en compte cette exigence relative
au retour des produits en fin de vie au sein de la communaut europenne. Par consquent vous pouvez retourner localement ces matriels dans les points de collecte.
MSI ,
, ....
()
( WEEE 2002/96/EC), 13
2005 , ,
, ,
. MSI
, MSI
EC, .
.
Preface
Under the European Union (EU) Directive on Waste Electrical and Electronic Equipment, Directive 2002/96/EC, which takes effect on August 13,
2005, products of electrical and electronic equipment cannot be discarded
as municipal waste anymore and manufacturers of covered electronic equipment will be obligated to take back such products at the end of their useful life. MSI will
comply with the product take back requirements at the end of life of MSI-branded products that are sold into the EU. You can return these products to local collection points.
Preface
ESPAOL
MSI como empresa comprometida con la proteccin del medio ambiente, recomienda:
Bajo la directiva 2002/96/EC de la Unin Europea en materia de desechos y/o equipos electrnicos, con fecha de rigor desde el 13 de agosto de 2005, los productos
clasificados como elctricos y equipos electrnicos no pueden ser depositados en
los contenedores habituales de su municipio, los fabricantes de equipos electrnicos,
estn obligados a hacerse cargo de dichos productos al termino de su perodo de vida.
MSI estar comprometido con los trminos de recogida de sus productos vendidos en
la Unin Europea al final de su periodo de vida. Usted debe depositar estos productos
en el punto limpio establecido por el ayuntamiento de su localidad o entregar a una
empresa autorizada para la recogida de estos residuos.
NEDERLANDS
Om het milieu te beschermen, wil MSI u eraan herinneren dat.
De richtlijn van de Europese Unie (EU) met betrekking tot Vervuiling van Electrische
en Electronische producten (2002/96/EC), die op 13 Augustus 2005 in zal gaan kunnen niet meer beschouwd worden als vervuiling. Fabrikanten van dit soort producten
worden verplicht om producten retour te nemen aan het eind van hun levenscyclus.
MSI zal overeenkomstig de richtlijn handelen voor de producten die de merknaam MSI
dragen en verkocht zijn in de EU. Deze goederen kunnen geretourneerd worden op
lokale inzamelingspunten.
SRPSKI
Da bi zatitili prirodnu sredinu, i kao preduzee koje vodi rauna o okolini i prirodnoj
sredini, MSI mora da vas podesti da
Po Direktivi Evropske unije (EU) o odbaenoj ekektronskoj i elektrinoj opremi, Direktiva 2002/96/EC, koja stupa na snagu od 13. Avgusta 2005, proizvodi koji spadaju
pod elektronsku i elektrinu opremu ne mogu vie biti odbaeni kao obian otpad i
proizvoai ove opreme bie prinueni da uzmu natrag ove proizvode na kraju njihovog
uobiajenog veka trajanja. MSI e potovati zahtev o preuzimanju ovakvih proizvoda
kojima je istekao vek trajanja, koji imaju MSI oznaku i koji su prodati u EU. Ove proizvode moete vratiti na lokalnim mestima za prikupljanje.
POLSKI
Aby chroni nasze rodowisko naturalne oraz jako firma dbajca o ekologi, MSI przypomina, e...
Zgodnie z Dyrektyw Unii Europejskiej (UE) dotyczc odpadw produktw elektrycznych i elektronicznych (Dyrektywa 2002/96/EC), ktra wchodzi w ycie 13 sierpnia
2005, tzw. produkty oraz wyposaenie elektryczne i elektroniczne nie mog by traktowane jako mieci komunalne, tak wic producenci tych produktw bd zobowizani
do odbierania ich w momencie gdy produkt jest wycofywany z uycia. MSI wypeni
wymagania UE, przyjmujc produkty (sprzedawane na terenie Unii Europejskiej) wycofywane z uycia. Produkty MSI bdzie mona zwraca w wyznaczonych punktach
zbiorczych.
vi
MS-7640
TRKE
evreci zelliiyle bilinen MSI dnyada evreyi korumak iin hatrlatr:
ESKY
Zle nm na ochran ivotnho prosted - spolenost MSI upozoruje...
Podle smrnice Evropsk unie (EU) o likvidaci elektrickch a elektronickch vrobk
2002/96/EC platn od 13. srpna 2005 je zakzno likvidovat elektrick a elektronick
vrobky v bnm komunlnm odpadu a vrobci elektronickch vrobk, na kter se
tato smrnice vztahuje, budou povinni odebrat takov vrobky zpt po skonen jejich ivotnosti. Spolenost MSI spln poadavky na odebrn vrobk znaky MSI,
prodvanch v zemch EU, po skonen jejich ivotnosti. Tyto vrobky mete odevzdat
v mstnch sbrnch.
MAGYAR
Annak rdekben, hogy krnyezetnket megvdjk, illetve krnyezetvdknt fellpve
az MSI emlkezteti nt, hogy ...
Az Eurpai Uni (EU) 2005. augusztus 13-n hatlyba lp, az elektromos s elektronikus berendezsek hulladkairl szl 2002/96/EK irnyelve szerint az elektromos
s elektronikus berendezsek tbb nem kezelhetek lakossgi hulladkknt, s az
ilyen elektronikus berendezsek gyrti kteless vlnak az ilyen termkek visszavtelre azok hasznos lettartama vgn. Az MSI betartja a termkvisszavtellel kapcsolatos kvetelmnyeket az MSI mrkanv alatt az EU-n bell rtkestett termkek
esetben, azok lettartamnak vgn. Az ilyen termkeket a legkzelebbi gyjthelyre
viheti.
ITALIANO
Per proteggere lambiente, MSI, da sempre amica della natura, ti ricorda che.
In base alla Direttiva dellUnione Europea (EU) sullo Smaltimento dei Materiali Elettrici
ed Elettronici, Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti appartenenti
alla categoria dei Materiali Elettrici ed Elettronici non possono pi essere eliminati come
rifiuti municipali: i produttori di detti materiali saranno obbligati a ritirare ogni prodotto
alla fine del suo ciclo di vita. MSI si adeguer a tale Direttiva ritirando tutti i prodotti
marchiati MSI che sono stati venduti allinterno dellUnione Europea alla fine del loro
ciclo di vita. possibile portare i prodotti nel pi vicino punto di raccolta
vii
Preface
Preface
Contents
Copyright Notice ii
Trademarks ii
Revision History ii
Technical Support ii
Safety Instructionsiii
FCC-B Radio Frequency Interference Statement iv
WEEE (Waste Electrical and Electronic Equipment) Statement v
Chapter 1 Getting Started1-1
Mainboard Specifications 1-2
Mainboard Layout 1-4
Packing Contents 1-5
Optional Accessories 1-5
viii
MS-7640
ix
Preface
RAID ConfigurationB-2
Chapter 1
Getting Started
Thank you for choosing the 990FXA-GD65 Series (MS7640 v3.X) ATX mainboard. The 990FXA-GD65 Series
mainboards are based on AMD 990FX & SB950 chipsets for optimal system efficiency. Designed to fit the
advanced AMD 64 bits PhenomTM II X6/ X4/ X3/ X2,
AthlonTM II X4/ X3/ X2 and SempronTM processor, the
990FXA-GD65 Series deliver a high performance and
professional desktop platform solution.
Getting Started
Mainboard Specifications
Processor Support
AMD PhenomTM II / AthlonTM II / SempronTM Processors with AM3/AM3+ package.
(For the latest information about CPU, please visit http://www.msi.com/service/cpusupport/)
HyperTransport
HyperTransport 3.0, supports up to 5.2 GT/s
Chipset
North Bridge: AMD 990FX chipset
South Bridge: AMD SB950 chipset
Memory Support
DDR3 2133 *(OC)/ 1866/ 1600/ 1333/ 1066/ 800 SDRAM (total 32 GB Max)
4 DDR3 DIMMs, supports Dual-Channel mode
*(OC means OverClocking, for more information on compatible components, please
visit http://www.msi.com/service/test-report/)
LAN
Supports PCIE Gb LAN (10/100/1000) by Realtek RTL8111E
Audio
HD audio codec integrated by Realtek ALC892
Flexible 8-channel audio with jack sensing
SATA
6 SATA 6Gb/s ports (SATA1~6) by AMD SB950
Supports hot plug & asynchronous notification
USB 3.0
2 USB 3.0 ports (back panel) by NEC D720200
RAID
SATA1~6 support RAID 0/ 1/ 5/ 10 mode by AMD SB950
1-2
MS-7640
Connectors
Chapter 1
Back panel
- 1 PS/2 keyboard/ mouse port
- 1 Clear CMOS button
- 1 Coaxial S/PDIF-Out port
- 1 Optical S/PDIF-Out port
- 8 USB 2.0 ports
- 2 USB 3.0 ports
- 1 LAN port
- 6 flexible audio ports
On-Board
- 2 USB 2.0 connectors
- 1 Serial port connector
- 1 Chassis Intrusion connector
- 1 S/PDIF-Out connector
- 1 Front Panel Audio connector
- 1 CD-In connector
- 1 TPM Module connector
Slots
2 PCIE x16 slots
4 PCIE x1 slots
1 PCI slot, supports 3.3V/ 5V PCI bus Interface
Form Factor
ATX (24.4cm X 30.5 cm)
Mounting
9 mounting holes
1-3
Getting Started
CPUFAN
Mainboard Layout
Top : mouse/ keyboard
Bottom:USB ports
JPWR2
Clear CMOS
Top:
Coaxial S/PDIF
Buttom:
Optical S/PDIF
USB 2.0 ports
SOCKET AM3
JPWR1
SYSFAN1
PWRCONN1
DIMM1
DIMM3
DIMM2
DIMM4
AMD
990FX
SYSFAN2
PCI_E1
PCI_E2
PCI_E3
AMD
SB950
SYSFAN3
PCI_E4
PCI_E5
BATT
+
PCI_E6
PCI1
SYSFAN4
JCI1
JBAT1
JAUD1
JCD1 JSP1
JCOM1
JUSB1
JUSB2
JTPM1
JFP2
JFP1
1-4
MS-7640
Packing Contents
Driver / Utility
DVD
User Guide
Back IO Shield
SATA Cable
Optional Accessories
USB 2.0
Bracket
USB 3.0
Bracket
S/PDIF Out
Bracket
eSATA
Bracket
V-Check
Cable
M-Connector
USB3 to USB2
Connector
SATA Power
Cable
CrossFire
Cable
SLI Cable
eSATA Power
Cable
* These pictures are for reference only and may vary without notice.
* The packing contents may vary according to the model you purchased.
* If you need to purchase the optional accessories, please visit http://www.msi.com/
index.php to inquire the part numbers or consult the dealer.
1-5
Chapter 1
Mainboard
Chapter 2
Hardware Setup
This chapter provides you with the information about
hardware setup procedures. While doing the installation, be careful in holding the components and follow the
installation procedures. For some components, if you
install in the wrong orientation, the components will not
work properly.
Use a grounded wrist strap before handling computer
components. Static electricity may damage the components.
Hardware Setup
JPWR2, p.2-9
CPU, p.2-4
CPUFAN, p.2-13
SYSFAN1,
p.2-13
DDR3, p.2-7
SOCKET AM3
Back Panel,
p.2-10
JPWR1, p.2-9
PWRCONN1,
p.2-9
SYSFAN2,
p.2-13
PCIE, p.2-18
JCI1, p.2-12
SATA1~6,
p.2-12
SYSFAN3,
p.2-13
SYSFAN4,
p.2-13
PCI, p.2-18
JBAT1, p.2-17
JCOM1,
p.2-15
JAUD1, p.2-13
JSP1, p.2-14
JCD1, p.2-15
2-2
JUSB1, JUSB2,
p.2-15
JTPM1, p.2-16
MS-7640
Screw Holes
When you install the mainboard, you have to place the mainboard into the chassis in the
correct direction. The locations of screws holes on the mainboard are shown as below.
Chapter 2
SOCKET AM3
Screw holes
Refer above picture to install standoffs in the appropriate locations on chassis and then
screw through the mainboard screw holes into the standoffs.
Important
To prevent damage to the mainboard, any contact between the mainboard circuit and
chassis or unnecessary standoffs mounted on the chassis is prohibited.
Please make sure there is no metal components placed on the mainboard or within
the chassis that may cause short circuit of the mainboard.
2-3
Hardware Setup
Important
Overheating
Overheating will seriously damage the CPU and system. Always make sure the cooling
fan can work properly to protect the CPU from overheating. Make sure that you apply
an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to
enhance heat dissipation.
Replacing the CPU
While replacing the CPU, always turn off the ATX power supply or unplug the power
supplys power cord from the grounded outlet first to ensure the safety of CPU.
Overclocking
This mainboard is designed to support overclocking. However, please make sure your
components are able to tolerate such abnormal setting, while doing overclocking. Any
attempt to operate beyond product specifications is not recommended. We do not guarantee the damages or risks caused by inadequate operation or beyond product specifications.
Gold arrow
2-4
MS-7640
2-5
Chapter 2
Hardware Setup
Important
While disconnecting the Safety Hook from the fixed bolt, it is necessary to keep an eye
on your fingers, because once the Safety Hook is disconnected from the fixed bolt, the
fixed lever will spring back instantly.
2-6
MS-7640
Memory
These DIMM slots are used for installing memory modules. For more information on
compatible components, please visit http://www.msi.com/service/test-report/
DDR3
240-pin, 1.5V
48x2=96 pin
DIMM1
DIMM3
DIMM2
DIMM4
DIMM1
DIMM3
DIMM2
DIMM4
Installed
Empty
Important
DDR3 memory modules are not interchangeable with DDR2 and the DDR3 standard
is not backwards compatible. You should always install DDR3 memory modules in
the DDR3 DIMM slots.
In Dual-Channel mode, make sure that you install memory modules of the same type
and density in different channel DIMM slots.
To enable successful system boot-up, always insert the memory modules into the
DIMM1 first.
Due to the chipset resource deployment, the system density will only be detected up
to 31+GB (not full 32GB) when each DIMM is installed with a 8GB memory module.
2-7
Chapter 2
72x2=144 pin
Hardware Setup
Notch
Volt
Important
You can barely see the golden finger if the memory module is properly inserted in the
DIMM slot.
2-8
MS-7640
Power Supply
ATX 24-pin Power Connector: JPWR1
d
n
u
ro
V
.G 5 V
4
2 3.+ +5 V
d
2 2. 5 s n d
2 1.+ Re ou un d
2 0. Gr ro un #
2 9. G o N d
1 8. Gr -O un
1 7. PS o
1 6. Gr 2V V
1 5. 1 .3
1 4.- +3
1 3.
1
V
.3
3 V
.+ 2 V
2 1 2
1 .+ +1 B OK
11 0. S R d
1 .5V W un
d
9 .P ro
8 .G 5V un
7 .+ ro nd
6 .G 5V u
5 + o V
r
.
4 .G 3.3 3V
.
3
+
.
3
2 .+
1
Important
Make sure that all the connectors are connected to proper ATX power supplies to ensure stable operation of the mainboard.
2-9
Chapter 2
This connector allows you to connect an ATX 24-pin power supply. To connect the ATX
24-pin power supply, make sure the plug of the power supply is inserted in the proper
orientation and the pins are aligned. Then push down the power supply firmly into the
connector.
You may use the 20-pin ATX power supply as you like. If youd like to use the 20-pin
ATX power supply, please plug your power supply along with pin 1 & pin 13.
Hardware Setup
Back Panel
Mouse/
Keyboard
LAN
Coaxial
S/PDIF-Out
Line-In RS-Out
Clear
CMOS
Button
Line-Out CS-Out
Optical
S/PDIF-Out
Mic
SS-Out
Mouse/ Keyboard
The standard PS/2 mouse/keyboard DIN connector is for a PS/2 mouse/keyboard.
Clear CMOS Button
There is a CMOS RAM on board that has a power supply from external battery to keep
the system configuration data. With the CMOS RAM, the system can automatically
boot OS every time it is turned on. If you want to clear the system configuration, use
the button to clear data. Press the button to clear the data.
Important
Make sure that you power off the system before clearing CMOS data.
After pressing this button to clear CMOS data in power off (G3) state, the system will
boot automatically.
Coaxial S/PDIF-Out
This SPDIF (Sony & Philips Digital Interconnect Format) connector is provided for digital
audio transmission to external speakers through a coaxial cable.
Optical S/PDIF-Out
This SPDIF (Sony & Philips Digital Interconnect Format) connector is provided for digital
audio transmission to external speakers through an optical fiber cable.
USB 2.0 Port
The USB (Universal Serial Bus) port is for attaching USB devices such as keyboard,
mouse, or other USB-compatible devices. Supports data transfer rate up to 480Mbit/s
(Hi-Speed).
2-10
MS-7640
Important
LAN
The standard RJ-45 LAN jack is for connection to
the Local Area Network (LAN). You can connect a
network cable to it.
Yellow
LED
Color
LED State
Condition
Left
Yellow
Off
On(Steady state)
Right
Green/ Orange
Green
Off
On
Orange
On
Audio Ports
These audio connectors are used for audio devices. It is easy to differentiate between
audio effects according to the color of audio jacks.
Line-In (Blue) - Line In, is used for external CD player, tape-player or other
audio devices.
Line-Out (Green) - Line Out, is a connector for speakers or headphones.
Mic (Pink) - Mic, is a connector for microphones.
RS-Out (Black) - Rear-Surround Out in 4/ 5.1/ 7.1 channel mode.
CS-Out (Orange) - Center/ Subwoofer Out in 5.1/ 7.1 channel mode.
SS-Out (Gray) - Side-Surround Out 7.1 channel mode.
2-11
Chapter 2
If you want to use a USB 3.0 device, you must use the USB 3.0 cable to connect to
the USB 3.0 port.
Hardware Setup
Connectors
Serial ATA Connector: SATA1~6
This connector is a high-speed Serial ATA interface port. Each connector can connect
to one Serial ATA device.
SATA5_6
SATA3_4
SATA1~6 (6Gb/s)
supported by SB950
SATA1_2
Important
Please do not fold the Serial ATA cable into 90-degree angle. Otherwise, data loss may
occur during transmission.
d
n
u RU
ro T
.G IN
2 .C
1
2-12
MS-7640
Chapter 2
d
o
n
u
/N
ro 2V or
.G 1 ns
1
+
e
.
2 .S
3
d
n
u
ro 2V or l
.G 1 s o
1 .+ en tr
2 .S on
3 .C
4
CPUFAN
SYSFAN1~4
U
se
Important
Please refer to the recommended CPU fans at processors official website or consult
the vendors for proper CPU cooling fan.
CPUFAN supports fan control. You can install Control Center utility that will automatically control the CPU fan speed according to the actual CPU temperature.
Fan cooler set with 3 or 4 pins power connector are both available for CPUFAN.
2-13
Hardware Setup
ch
it
Spe
E
D
Buz
zer
.+
8 .
6
+
.
4 .
2
JFP2
D D
in E LE
P rL d
o e n
.N w e d
7 .Po sp n
5 Su rou
.
3 .G
1
ch
it
w
d
e tS
rv e
D
s
E
se e
L
e R
D
.R
D
9 .+
H
7 .5
.
3 .+
1
JFP1
ake
115V
d
n
u F
ro DI
.G P
1 .S CC
2 .V
3
* The MB layout in this figure is for reference only.
2-14
MS-7640
Chapter 2
115V
d
C un +
.N o 1
0 r B 11 .G
8 S B
.U S
6 .U C
4 VC
.
2
in
P nd
o u +
.N ro 0
9 .G SB 07 U B
.
S
5 .U CC
3 .V
1
d
n
u nd
.L ro u
1 .G ro
2 G
.
3 .R
4
2-15
Hardware Setup
This connector connects to a TPM (Trusted Platform Module) module (optional). Please
refer to the TPM security platform manual for more details and usages.
TPM module is optional
115V
2-16
3
in
p 2
ta in
a p 1
d ta pin 0
n
e s & da ta pi
m s & da ta
a
ra re s
F d s & d
C ad dre ss &
P
re s
.L C d d s
3 P a d re
1 1.L C a dd et
1 .LP C a es k
9 P C R loc
L
.
7 .LP C C
5 .LP C
3 .LP
1
d
n
u d
r
ro un n r
e
.G ro Pi we Q r ow
4
1 2.G o Po IR we y p
1 0.N V ial o b
1 .5 r P nd
8 .Se 3V ta
6 .3. S
4 .3V
2
MS-7640
Jumpers
Clear CMOS Jumper: JBAT1
JBAT1
Keep Data
Clear Data
Important
You can clear CMOS by shorting 2-3 pin while the system is off. Then return to 1-2
pin position. Avoid clearing the CMOS while the system is on; it will damage the mainboard.
2-17
Chapter 2
There is a CMOS RAM onboard that has a power supply from an external battery to
keep the data of system configuration. With the CMOS RAM, the system can automatically boot OS every time it is turned on. If you want to clear the system configuration,
set the jumper to clear data.
Hardware Setup
Slots
PCIE (Peripheral Component Interconnect Express) Slot
The PCIE slot supports the PCIE interface expansion card.
PCIE x1 Slot
Important
When adding or removing expansion cards, make sure that you unplug the power supply first. Meanwhile, read the documentation for the expansion card to configure any
necessary hardware or software settings for the expansion card, such as jumpers,
switches or BIOS configuration.
2-18
Order2
Order3
Order4
INT G# INT H#
INT E#
INT F#
MS-7640
SOCKET AM3
2-19
Chapter 2
Hardware Setup
Off
CPU is in 2 phase power mode.
CPU is in 4 phase power mode.
CPU is in 6 phase power mode.
CPU is in 8 phase power mode.
2-20
Chapter 3
BIOS Setup
This chapter provides information on the BIOS Setup
program and allows you to configure the system for optimum use.
You may need to run the Setup program when:
An error message appears on the screen during
the system booting up, and requests you to run
SETUP.
You want to change the default settings for customized features.
BIOS Setup
Entering Setup
Power on the computer and the system will start POST (Power On Self Test) process.
When the message below appears on the screen, press <DEL> key to enter Setup.
Important
The items under each BIOS category described in this chapter are under continuous
update for better system performance. Therefore, the description may be slightly different from the latest BIOS and should be held for reference only.
Upon boot-up, the 1st line appearing after the memory count is the BIOS version. It is
usually in the format:
6th digit refers to the chipset as I = Intel, N = nVidia, A = AMD and V = VIA.
3-2
MS-7640
Control
Keyboard
Mouse
<><>
<><>
Description
Select Item
Chapter 3
<Enter>
Select Screen
Select Icon/ Field
<+>
<->
<F1>
General Help
<F4>
CPU Specifications
<F5>
Enter Memory-Z
<F6>
<F10>
<Esc>
Exit
Sub-Menu
If you find a right pointer symbol (as shown in the right view) appears to the left of
certain fields that means a sub-menu can be launched from this field. A sub-menu
contains additional options for a field parameter. You can use arrow keys ( ) or
mouse to highlight the field and press <Enter> or double-click the left mouse button to
enter the sub-menu. Then you can use the control keys to enter values and move from
field to field within a sub-menu. If you want to return to the previous menu, just press the
<Esc > or click the right mouse button.
3-3
BIOS Setup
Main Menu
Use this menu for basic system configurations, such as time, date etc.
Advanced
Use this menu to setup the items of the BIOS special enhanced features, integrated
peripherals, power management and PC health status.
Overclocking
Use this menu to specify your settings for frequency/voltage control and overclocking.
M-Flash
Use this menu to read/ flash the BIOS from storage drive (FAT/ FAT32 format only).
Security
Use this menu to set supervisor and user passwords.
Green Power
Use this menu to specify the power.
phase.
Boot
Use this menu to specify the priority of boot devices.
Save & Exit
This menu allows you to load the BIOS default values or factory default settings into the
BIOS and exit the BIOS setup utility with or without changes.
3-4
MS-7640
Main Menu
Chapter 3
System Date
This allows you to set the system to the date that you want (usually the current date).
The format is <day><month> <date> <year>.
[day]
Day of the week, from Sun to Sat, determined by BIOS. Readonly.
[month]
The month from Jan. through Dec.
[date]
The date from 1 to 31 can be keyed by numeric function keys.
[year]
The year can be adjusted by users.
System Time
This allows you to set the system time that you want (usually the current time). The time
format is <hour> <minute> <second>.
SATA Port1~6
Press <Enter> to enter the sub-menu. The sub-menu shows the information of installed
SATA device.
Important
SATA Port1~6 are appearing when you connect the HD devices to the SATA connectors on the mainboard.
System Information
This area shows the CPU information, BIOS version and memory status of your system
(read only).
3-5
BIOS Setup
Advanced
MS-7640
Integrated Peripherals
Press <Enter> to enter the sub-menu.
Chapter 3
USB Devices:
This item shows the type of installed USB device.
USB Controller
This item allows you to enable/ disable the USB controller.
Legacy USB Support
Set to [Enabled] if you need to use any USB 1.1/2.0 device in the operating system
that does not support or have any USB 1.1/2.0 driver installed, such as DOS and
SCO Unix. Set to [Disabled] only if you want to use any USB device other than the
USB mouse.
3-7
BIOS Setup
3-8
MS-7640
Hardware Monitor
Press <Enter> to enter the sub-menu.
EUP 2013
This item is designed for Energy Using Products Lot 6 2013 (EuP) aka Energy
Related Products (ErP). To reduce Power Consumption when system off or standby
mode.
Note: When Enabled EuP 2013 setting, system dont support RTC wake up event
function.
Restore on AC Power Loss
This item specifies whether your system will reboot after a power failure or interrupt
occurs. Settings are:
[Power Off] Always leaves the computer in the power off state.
[Power On] Always leaves the computer in the power on state.
[Last State]
Restore the system to the status before power failure or interrupt
occurred.
3-9
Chapter 3
BIOS Setup
Wake Up Event By
Setting to [BIOS] activates the following fields, and use the following fields to set the
wake up events. Setting to [OS], the wake up events will be defined by OS.
Resume By RTC Alarm
The field is used to enable or disable the feature of booting up the system on a
scheduled time/date.
Date/ HH:MM:SS
If Resume By RTC Alarm is set to [Enabled], the system will automatically resume
(boot up) on a specific date/hour/minute/second specified in these fields (using the
<+> and <-> to select the date & time settings).
Resume By PCI or PCI-E Device
When set to [Enabled], the feature allows your system to be awakened from the
power saving modes through any event on PCI or PCIE device.
Resume From S3 by USB Device
The item allows the activity of the USB device to wake up the system from S3 (Suspend to RAM) sleep state.
Resume From S3 by PS/2 Mouse/ Keyboard
These items determine whether the system will be awakened from S3 state when
input signal of the PS/2 mouse/ keyboard is detected.
3-10
MS-7640
Overclocking
Chapter 3
3-11
BIOS Setup
DRAM Frequency
This item is used to adjust the DRAM frequency. Setting to [Auto], the system will detect
the DRAM Frequency automatically.
Adjusted DRAM Frequency
It shows the adjusted Memory frequency. Read-only.
DRAM Timing Mode
This field has the capacity to automatically detect the DRAM timing.
Advanced DRAM Configuration
Press <Enter> to enter the sub-menu.
Command Rate
This setting controls the DRAM command rate.
tCL
This controls the CAS latency, which determines the timing delay (in clock cycles)
before SDRAM starts a read command after receiving it.
tRCD
When DRAM is refreshed, both rows and columns are addressed separately. This
setup item allows you to determine the timing of the transition from RAS (row address
strobe) to CAS (column address strobe). The less the clock cycles, the faster the
DRAM performance.
tRP
This setting controls the number of cycles for Row Address Strobe (RAS) to be
allowed to precharge. If insufficient time is allowed for the RAS to accumulate its
charge before DRAM refresh, refreshing may be incomplete and DRAM may fail
to retain data. This item applies only when synchronous DRAM is installed in the
system.
tRAS
This setting determines the time RAS takes to read from and write to memory cell.
tRTP
Time interval between a read and a precharge command.
3-12
MS-7640
tRC
The row cycle time determines the minimum number of clock cycles a memory row
takes to complete a full cycle, from row activation up to the precharging of the active
row.
tRRD
Specifies the active-to-active delay of different banks.
tWTR
Minimum time interval between the end of write data burst and the start of a columnread command. It allows I/O gating to overdrive sense amplifiers before read
command starts.
tRFC
This setting determines the time RFC takes to read from and write to a memory
cell.
Advanced Channel 1/ 2 Timing Configuration
Press <Enter> to enter the sub-menu. And you can set the advanced memory timing
for each channel.
3-13
Chapter 3
tWR
Minimum time interval between end of write data burst and the start of a precharge
command. Allows sense amplifiers to restore data to cells.
BIOS Setup
System restart.
Success
Fail
Important
This CPU core unlocked behavior depends on the CPU ability/ characteristic, and it
is not guaranteed.
Depend on CPUs characteristic, once you get instable scenario, please restore the
default settings for system.
You can also check the core numbers in performance tab of Windows task
manager.
OC Genie Lite
Setting this item to [Enabled] allows the system to detect the maximum FSB clock and
to overclock automatically. If overclocking fails to run, you can try the lower FSB clock
for overclocking successfully.
Spread Spectrum
When the mainboards clock generator pulses, the extreme values (spikes) of the pulses
create EMI (Electromagnetic Interference). The Spread Spectrum function reduces the
EMI generated by modulating the pulses so that the spikes of the pulses are reduced
to flatter curves.
Important
If you do not have any EMI problem, leave the setting at [Disabled] for optimal system
stability and performance. But if you are plagued by EMI, select the value of Spread
Spectrum for EMI reduction.
The greater the Spread Spectrum value is, the greater the EMI is reduced, and the
system will become less stable. For the most suitable Spread Spectrum value, please
consult your local EMI regulation.
Remember to disable Spread Spectrum if you are overclocking because even a slight
jitter can introduce a temporary boost in clock speed which may just cause your
overclocked processor to lock up.
3-14
MS-7640
OC Retry Count
When overclocking has failed, setting this item as [1, 3] will allow system to reboot
1/ 3 times with the same overclocked configuration. If overclocking has failed every
time, the system will restore the defaults.
CPU Specifications
Press <Enter> to enter the sub-menu. The submenu shows the information of installed
CPU.
3-15
Chapter 3
Overclocking Profile 1/ 2/ 3/ 4/ 5/ 6
Press <Enter> to enter the sub-menu. In the sub-menu, these items are used to save
the current settings, and you can to load the settings from the stored profile.
BIOS Setup
CPU Features
Press <Enter> to enter the sub-menu.
AMD CoolnQuiet
The CoolnQuiet technology can effectively and dynamically lower CPU speed and
power consumption.
Important
To ensure that CoolnQuiet function is activated and will be working properly, it is
required to double confirm that:
Run BIOS Setup, and select Cell Menu. Under Cell Menu, find AMD CoolnQuiet,
and set this item to Enabled.
Enter Windows, and select [Start]->[Settings]->[Control Panel]->[Power Options].
Enter Power Options Properties tag, and select Minimal Power Management under
Power schemes.
C1E
Enable this item to reduce the CPU power consumption while idle. Not all processors
support Enhanced Halt state (C1E).
SVM Mode
This item allows you to enable/disable the AMD SVM (Secure Virtual Machine)
Mode.
IOMMU Mode
This item allows you to enable/disable the IOMMU (I/O Memory Management Unit)
for I/O virtualization.
HT Link Control
Press <Enter> to enter the sub-menu.
3-16
MS-7640
M-Flash
Chapter 3
BIOS Boot Function
This allows you to enable/ disable the system to boot from the BIOS file inside USB
drive (FAT/ 32 format only).
Select one file to Boot
When the BIOS Boot function as sets to [Enabled], this item is selectable. This item
allows to select particular BIOS file from the USB/ Storage (FAT/ 32 format only) drive.
And the system will boot from selected BIOS file.
Save BIOS to storage
Please setup a specific folder in specific USB/ Storage drive to save BIOS file from
BIOS ROM chip data. Note: it only supports FAT/ 32 file system drive.
Select one file to update BIOS
This item allows you to select particular BIOS file from the USB/ Storage (FAT/ 32 format only) drive for updating BIOS.
3-17
BIOS Setup
Security
Administrator Password
This item is used to set the administrator password. When a administrator password
has been set, you will be prompted to enter it every time you try to enter BIOS Setup.
User Password
This item is used to set the user password. When a user password has been set, you
will be prompted to enter it every time you try to enter the operating system.
Important
When you select the Administrator Password / User Password item, a password box will
appear on the screen. Type the password, and press <Enter>. The password typed now
will replace any previously set password from CMOS memory. You will be prompted to
confirm the password. Retype the password and press <Enter>. You may also press
<Esc> to abort the selection and not enter a password.
To clear a set password, just press <Enter> when you are prompted to enter the
password. A message will show up confirming the password will be disabled. Once
the password is disabled, the system will boot and you can enter Setup/ OS without
entering any password.
These two items prevent an unauthorized person from changing any part of your system
configuration.
U-Key
This item is used to enable/ disable USB drive as a key.
3-18
MS-7640
Make U-Key at
When the U-Key as sets to [Enabled], this item is selectable. This item allows you to
specify the USB drive.
Chassis Intrusion Configuration
Press <Enter> to enter the sub-menu.
3-19
Chapter 3
Chassis Intrusion
This item enables or disables the feature of recording the chassis intrusion status
and issuing a warning message if the chassis is once opened. To clear the warning
message, set the field to [Reset]. The setting of the field will automatically return to
[Enabled] later.
BIOS Setup
Green Power
EUP 2013
This item is designed for Energy Using Products Lot 6 2013 (EuP) aka Energy Related
Products (ErP). To reduce Power Consumption when system off or standby mode.
Note: When Enabled EuP 2013 setting, system dont support RTC wake up event
function.
CPU Phase Control
This item allows you to select the CPU power phase mode to reach the best power
saving function.
Motherboard LED Control
This item is used to turn on (Auto)/ turn off (Disabled) the power phase LEDs of the
mainboard.
C1E
Enable this item to reduce the CPU power consumption while idle. Not all processors
support Enhanced Halt state (C1E).
3-20
MS-7640
Boot
Chapter 3
Full Screen Logo Display
This item enables this system to show the company logo on the boot-up screen. Settings are:
[Enabled]
Shows a still image (logo) on the full screen at boot.
[Disabled]
Shows the POST messages at boot.
== Boot Option Priorities ==
1st~9th Boot
You can select the boot priorities in these Boot Option items.
USB KEY Drive/ UEFI Boot Drive BBS Priorities
Boot Option
You can select the USB KEY Drive/ UEFI Boot priorities in these Boot Option
items.
3-21
Appendix A
Realtek Audio
The Realtek audio provides 10-channel DAC that simultaneously supports 7.1 sound playback and 2 channels
of independent stereo sound output (multiple streaming)
through the Front-Out-Left and Front-Out-Right channels.
Realtek Audio
For Windows XP, you must install Windows XP Service Pack3 or later before installing
the driver.
The following illustrations are based on Windows 7 environment and could look slightly
different if you install the drivers in different operating systems.
1. Insert the application DVD into the DVD-ROM drive. The setup screen will automatically appear.
2. Click Driver tab.
3. Click AUDIO button.
Click here
Important
The HD Audio Configuration software utility is under continuous update to enhance audio applications. Hence, the program screens shown here in this section may be slightly
different from the latest software utility and shall be held for reference only.
A-2
MS-7640
Software Configuration
After installing the audio driver, the Realtek HD Audio Manager icon will appear at the
notification area (lower right of the screen). You may double click the icon and the GUI
will pop up accordingly.
Appendix A
It is also available to enable the audio driver by clicking the Realtek HD Audio Manager
from the Control Panel.
Volume Adjustment
Application Enhancement
A-3
Realtek Audio
Device Selection
Here you can select a audio output source to change the related options. The check
sign (in orange) indicates the devices as default.
Volume Adjustment
You can control the volume or balance the right/left side of the speakers that you
plugged in front or rear panel by adjust the bar.
Application Enhancement
The array of options will provide you a complete guidance of anticipated sound effect for
both output and input device.
Jack status panel
This panel depicts all render and capture devices currently connected with your computer.
As you know, each jack corresponds to its default setting, you can refer to the next section Hardware Default Setting.
A-4
MS-7640
Appendix A
Fro
nt
nt
Rea
A-5
Realtek Audio
nt
Cen
ter
ubw
Rea
oof
er
nt
Cen
ter
S id
A-6
&S
&S
eS
ubw
urro
Rea
oof
er
und
Appendix B
AMD RAID
The integrate one SATA host controller separately, and
support RAID function for performance and reliability.
SB950 SATA RAID provides support for RAID 0 (Striping), RAID 1 (Mirroring), RAID 10 (Striping & Mirroring)
& RAID 5 (striping with parity). RAID 0 greatly improves
hard disk I/O performance by concurrently striping data
across multiple drives. RAID 1 makes sure data is not
lost if a drive fails as data is simultaneously written to
two drives. Drives configured for RAID Striping are said
to form a RAID 0 set, while drives configured for RAID
Mirroring are said to form a RAID 1 set. RAID 10 is implemented as a mirrored array whose segments are RAID
0 arrays. RAID 10 has same fault tolerance as mirroring
and reduces overhead by striping. It needs at least four
drives to form a RAID 10. RAID 5 defines techniques for
parity data.
AMD RAID
RAID Configuration
Creating and deleting RAID set and performing other RAID setting up operations are
done in the RAID BIOS. During bootup, a screen similar to the one below will appear for
about few seconds. Press <Ctrl-F> to enter RAID Option ROM utility.
Important
Be sure to enable the RAID function for SATA device in BIOS before configuring the
RAID Option ROM Utility.
The RAID Option ROM utility menu screen will appear. The Main Menu is used to
choose the operation to be performed.
B-2
MS-7640
Appendix B
B-3
AMD RAID
2. And then press [Ctrl + C] keys to enter the LD Define Menu. Use the space key
to choose a RAID mode (RAID 0/ 1/ 10/ 5) and use the arrow key to move to the
Drives Assignments window.
B-4
MS-7640
Stripe Block Size, the default 64KB is best for most applications. RAID 0 or 10
only.
Gigabyte Boundary, allows use of slightly smaller replacement drives.
4. A message will show, press [Ctrl + Y] to input a LD name as your desire or press
any key to save default LD name.
5. Another message will show, press [Ctrl-Y] if you are sure to erase the MBR data of
the disk. Or press any key to ignore this option.
B-5
Appendix B
3. On the Drives Assignments window, use the arrow key to choose the hard drives
which you want to make part of the LD, use the space key to change the assignment
to Y. Then press [Ctrl+Y] to save the configuration.
AMD RAID
6. The message will show up on the bottom, press any key to use maximum capacity
or press [Ctrl-Y] to modify array capacity manually.
Important
The default capacity is the full capacity of the selected hard drives.
If you allocate the first LD capacity manually, you can create second LD with remaining capacity of the selected hard drives.
7. The LD creation is done, the screen shows the LD information as below.Press ESC
key to the main screen.
8. Press ESC key to exit the utility, a message System is going to REBOOT! Are You
Sure? will display, answer Y to exit it and the system will reboot.
B-6
MS-7640
Appendix B
3. On the next screen, a message will display to inform you, press Ctrl+Y to delete
the RAID set or other key to abort it. Press Ctrl+Y to complete the deletion.
B-7
AMD RAID
Important
Please follow the instruction below to make a SATA RAID driver for yourself.
Insert the MSI DVD into the DVD-ROM drive.
Click the Browse CD on the Setup screen.
Copy all the contents in the : \\ChipSet\AMD\Packages\Drivers\SBDrv\SB9xx\RAID\
(and then, please select a folder which was classified according to OS.)
The driver disk for RAID controller is done.
4. When prompted, insert the medium disk and press Enter.
For Windows Vista/ Windows 7:
During the Operating system installation, after selecting the location to install Vista/
Windows 7 click on Load Driver button to load RAID drive.
5. You should be shown a list of available RAID controller(s).
6. Select the compatible RAID controller for 32-bit/ 64-bit version system and then
press ENTER.
7. The next screen should confirm that you have selected the RAID controller. Press
ENTER again to continue.
8. You have successfully installed the RAID driver, and Windows setup should continue.
9. Leave the medium until the system reboots itself. Windows setup will need to copy
the files from the medium again after the RAID volume is formatted, and Windows
setup starts copying files.
B-8
MS-7640
B-9
Appendix B
3. Under the Driver tab, click on AMD chipset drivers by your need. The AMD chipset
drivers includes RAID Driver.