Beruflich Dokumente
Kultur Dokumente
Abstract
Despite major concern of industries on profitability, there has been growing awareness
on the importance of considering environmentally conscious design of new processes.
Consideration of environmental, health and safety aspects in the initial stages of
chemical process design will not only lead to safer and environmentally benign plants,
but overall cost reduction. The interest of this paper is on methods that consider
environmental impacts as part of chemical process hazards. Eight methods are reviewed
for their goal and scope, developer and considered aspects. The methods differ
significantly in the considered aspects and parameters, which consequently influencing
the way data is processed. The applicability of the methods with the environmental
friendliness definition from chemical process stand point is also explained. The paper
provides a reference for the comparison of the existing environmental assessment
methods targeting various stages of chemical process design. The review finds that
despite all the advantages of each of the methods, none is able to address all the
environmental aspects of a process. Also none provides assessment approach for
different plant stages. Therefore, further improvement of the assessment methods is
needed.
Keywords: Environmental assessment;
Environmentally benign process.
Design
stage;
Chemical
process;
1. Introduction
Chemical processes offer a varied collection of important products and materials
categorized from health care to transportation and food processing. Chemical industry is
an essential key to nations economic health and modern societies. However, the
industry is also a main source of pollution since it generates considerable amount of
waste and emissions to the environment (Pereira, 1999). The effort of incorporating
pollution prevention techniques into process design is not something new and dated
back to the 1970s. Till date, the most widely adopted strategy by process industries for
environmental protection is the end-of-pipe pollution control techniques, which revolve
around waste treatment, toxicity diminution and industrial discharge volume reduction.
264
S.Abbaszadeh et al.
By using these add-on systems, hazards however still remain in the process and the
associated risks to the receptors can only be reduced through add-on counter measures
(Hassim and Hurme, 2010). Such strategy is costly as industries need to try different
new technologies to cope with the regulations (especially on discharges and emissions),
which are continuously getting stricter and stricter. Besides as mentioned earlier, the
strategy does not get rid of the problems at the root cause through hazards elimination
or reduction, but focuses on minimizing the impacts and probability of the unwanted
events. In contrary, the new pollution prevention techniques (known as clean
technology) have been later introduced to increase the environmental friendliness of
processes through prevention or elimination of intrinsic hazards arising from a process.
Such concept may offer more cost-effective and sustainable solutions compared to endof-pipe control methods.
Plenty of major decisions on process including raw materials, technologies and
operations, are made during the process development and conceptual design phase.
Based on the concept of inherent safety (Kletz, 1991), the best approach towards
designing an environmentally benign process is to consider the environmental aspect
early when developing a new process or retrofitting an existing one.
Inherent environmentally friendlier processes are those that have reduced or even
avoided hazards as well as inherently low levels of operational impacts (Gunasekera and
Edwards, 2006). Early hazards assessment poses a lot of advantages in a way that
inherent environmental friendly features can be adopted into the process with larger
degree of freedom and at lower costs. Despite the complications encountered due to
limited data availability, abundance of qualitative and quantitative methods have been
introduced for assessing the aspect at early process lifecycle phase. A number of
attempts have been made to analyze and classify the large variety of methods for
environmental assessment of chemical processes i.e. by Hertwich et al. (1997), Koller et
al. (2001) and Adu et al. (2008). The methods were reviewed from different viewpoints
including design and optimization of process, substance ranking, life cycle assessment
and environmental footprint. Even though extensive reviews have been done on
environmental assessment methods, similar works focusing on environmental safety are
still lacking. In this paper, environmental safety refers to the environmental- related
properties of chemical substances and process conditions (e.g. waste emissions and
discharges) due to normal, day-to-day operations. The focus of assessing such
properties is on chemical processes during the early design stage. This is the same as
inherent safety (Kletz, 1984) and inherent occupational health concepts (Hassim and
Hurme, 2010).
In this paper, eight of the existing methods for environmental assessment of chemical
process design are reviewed, critically summarized and compared qualitatively. The
methods are categorized based on several aspects including the specific aim and target
stage of assessment, set of environmental impact categories, considered parameters,
assessment approach as well as results presentation. The objective of this study is to
compare the applicability of the previous methodologies to assess environmental
friendliness of a process inherent level during early stages of design phase. The same
attempts have been done before for inherent safety and occupational health criteria.
2. Methodology
2.1. Selection of methods
The index-based methods for environmental assessment during conceptual process
design were mostly developed based on the inherent safety concept and within the
limited data availability. Based on the criteria above, eight methods have been selected
and summarized in Table 1. The methods are mostly for early design stage i.e. R&D,
the rest are applicable for retrofitting of the existing plants i.e. GERA, MBEI. The main
interest here is on the former ones since those methods have higher application for
designing process with inherent environmentally friendliness features.
Table 1. Reviewed environmental assessment methodologies applicable in design stage.
Method
Year
Author/s
Aim
Design
stage
Environmental
hazard index (EHI)
Waste reduction
(WAR) algorithm
1997
R&D
1999
Atmospheric hazard
index (AHI)
2003
Gunasekera and
Edwards
R&D
Integrated
environmental index
(IEI)
Global
environmental risk
assessment index
(GERA)
Inherent
environmental
toxicity index (IETI)
2004
Jia et al.
2004
Archour et al.
2006
Gunasekera and
Edwards
R&D
2009
Li et al.
Flowsheeting
stage
Flowsheeting
stage
Flowsheeting
stage
R&D
To estimate environmental impacts as a
result of total loss of inventories
2011
Torres et al.
To estimate environmental impacts as a
result of total loss of inventories
R&D and
preliminary
stages
266
S.Abbaszadeh et al.
Moreover, four of the reviewed methods are computer-based approaches like WAR,
GERA, IEI, TOPSIS, MBEI. For instance, the WAR algorithm used Chemcad III
process simulator and the IEI used PRO/II simulator. Electronic chemical property
database as well as computer-aided tools are highly in need especially for assessment at
early design stage since abundant of processes need to evaluated within a very limited
time.
Different methods have their own unique consideration of assessment parameters.
Among the most common impacts evaluated are ozone depletion, global warming as
well as aquatic, terrestrial, and atmospheric toxicities.
The WAR algorithm offers minimization of environmental footprint in chemical
process. Despite offering a strong methodology for environmental evaluation, it is not
applicable in the R&D stage since a large amount of data is needed (i.e. mass balance).
The EHI on the other hand utilizes very limited data of raw material and reaction
chemistry only to rank the alternative routes by the environmental impact level. The
method considers terrestrial and aquatic ecosystems only due to total loss of
contaminant.
Even though the AHI method does not cover soil and water media, it does consider all
the typical five impact categories of toxicity, acidification, photochemical smog, ozone
depletion and global warming. Despite the advantages of the AHI and EHI methods,
their applicability to chemical process design is actually quite limited since they are
complicated and protracted. Later, the IETI as a combination of the AHI and EHI is
proposed to estimate inherent environmental friendliness of chemical plant more
comprehensively by including all the environmental media. Besides all the advantages
introduced by IETI it still needs improvements to include also the environmental
impacts due to daily routine operation in the plant.
The IEI method as a multi-criteria decision-making tool was developed in three steps 1) process environmental performance assessment (PEPA), 2) integrated environmental
index development and 3) analytic hierarchy process (AHP). The GERA utilizes data
from material safety data sheet (MSDS) and design principles of unit operations. In
addition, it also uses the same material scoring system as used in the national fire
protection association (NFPA) and hazardous material identification system (HMIS)
ratings. The TOPSIS as a decision making tool identified a set of optimal parameters for
designing an environmentally conscious design of chemical process at initial stage of
design. It comprises of three steps of model construction, model solution and model
strategy for design and optimization of chemical process based on green chemical
principles. MBEI framework evaluates environmental performance of a process based
on materials flows data. It can be used for both new processes at any stage of design as
well as retrofitting the existing plants.
References
C.M. Torres, M.A. Gadalla, J.M. Mateo-sanz, and L.J. Esteller, 2011, Evaluation tool for the
environmnetal design of chemical processes, Industrial and engineering Chemistry Research,
50, 13466-134774.
268
S.Abbaszadeh et al.
C.J.Pereira, 1999, Environmentally friendly processes, Chem. Eng. Sci., 54, 13-14, 1959-1973.
Ch. Li, X. Zhang and S. Suzuki, 2009, Environmentally consious design of chemical process and
products: multi-optimization method, Chemical engineering research and design, 87, 233-243.
D. Mackay and S.Peterson, 1990, Fugacity models in practical applications of quantitative
structure activity relationship (QSAR). Environmental Chemistry and Technology, 433-460.
G. Koller, U. Fischer, Hungerbuhler, 2000, Comparisons of methods for assessing human health
and environmental impact in early phases of chemical process development. ESCAPE10(10th European Symposium on Computer Aided Process Engineering), Florence, Italy,
931-936.
H. Cabezas, J.C. Bare, S.K. Mallick, 1999, Pollution prevention with chemical process
simulators: the generalized waste reduction (WAR) algorithm-full version. Computers and
Chemical Engineering, 23, 623-634.
H. Chen, Y. Wen, M.D. Waters, D.R. Shonnard, 2002, Design guidance for chemical process
using environmental and economic assessment. Ind. Eng. Chem. Res., 41, 4503-4513.
H. Sugiyama, U. Fischer, K. Hungerbuhler, M. Hiro, 2008, Decision framework for chemical
process design industry different stage of environmental, health and safety assessment. J
AICHE, 54 (4), 1037-1053.
I. K. Adu, H. Sugiyama, U. Fischer, K. Hungerbuhler, 2008, Comparisons of methods for
assessing environmental, health and safety (EHS) hazards in early phases of chemical process
design. Process Safety and Envionmental Protection, 86, 77-93.
M.H. Archour, A.E. Haroun, C.J. Schult, K.A.M. Gasem, 2004, A new method to assess the
environmental risk of a chemical process. Chemical Engneering and Processing: Process
Intensification, 44 (8), 901-909.
M.H. Hassim, M. Hurme, 2010, Inehernt occupational health assessment during process resaerch
and development stage. Journal of Loss Prevention in the Process Industries, 23, 127-138.
M.Y. Gunasekera, D.W. Edwards, 2003, Estimating the environmental impact of catastrophic
chemical release to the atmospheric and index method for ranking alternative chemical
process route. Journal of Process Safety and Environmental Protection, 81(6), 463-474.
M.Y. Gunasekera, D.W. Edwards, 2006, Chemical process route selection based upon the
potential toxic impact on the aquatic, terresterial and atmospheric environments. Journal of
Loss Prevention in the Process Industries, 19, 60-69.
T.A. Kletz, 1984, Cheaper, safer plants, or wealth and safety at work: notes on inherently safer
and simpler plants. Institution of chemical engineers, Rugby, ISBN 0-85295-167-1.
T.A. Kletz, 1991, Plant design for safety: A user friendly approach. New York: Hemisphere p.
140.
S.R. Cave, D.W. Edwards, 1997, Chemical process route selection based in assessment of
inherent environmental hazard. Computers and Chemical Engineering, 21, S965-S970.
X. Jia, F.Y. Han, X.S. Tan , 2004, Integrated environmental performance assessment of chemical
processes. Computers and Chemical Engineering, 23,243-247.