Beruflich Dokumente
Kultur Dokumente
EQUIPMENT DESCRIPTION
It consists of two Catridge Filters with jet pulse cleaning system and
high pressure centrifugal fan.
Equipment manufactured in steel plate, which has an income of dirty
air, dirty chamber where the Cartridge, a clean chamber where the
air filter, where the automatic cleaning system and an air outlet filter
is reached are located.
FAN
MANOMETER
FILTERS
COMPRESSOR
FAN
Model
Type
Flow rate
Engine power
Transmission
: IV-15-L/B
: CBM T/4-270/200 CV.
: 1500 Mt3/hr
: 1 HP
: direct transmission.
FILTER
Use
COMPRESSOR
Work pressure
Engine power
Electrical feeding
: 6 Bar
: 3 HP.
: 380 Volt 60hz
MANOMETER
Housing: Die cast aluminum case and bezel, with acrylic cover.
Exterior finish is coated gray to withstand 168 hour
salt spray corrosion test.
Accuracy: 2% of full scale (3% on - 0, -100 Pa, -125 Pa,
10MM and 4% on - 00, -60 Pa, -6MM ranges),
throughout range at 70F (21.1C).
Pressure Limits: -20 Hg. to 15 psig. (-0.677 bar to 1.034
bar);MP option: 35 psig (2.41 bar), HP option:80
psig (5.52 bar).
Overpressure: Relief plug opens at approximately 25 psig
(1.72 bar), standard gages only.
Temperature Limits: 20 to 140F.* (-6.67 to 60C).
Process Connections: 1/8 female NPT duplicate high and low
pressure taps - one pair side and one pair back.
Weight: 1 lb 2 oz (510 g), MP & HP 2 lb 2 oz (963 g)
VALVES
Model
Work Pressure
Electrical Feeding:
: AE 1440 R 225:
:90 PSI
:220V
Pressure Differential
Service: Air and non-combustible, compatible gases
Temperature Limits: Process and ambient temperature from -4
to 185F (-20 to 85C)
Pressure Limits: Max. Operating Pressure: 40' w.c. (10 kPa)
for all pressure ranges
Switch Type: Single-pole double-throw (SPDT)
Electrical Rating: Max., 1.5A/250 VAC, max. switching rate: 6
cycles/min.; Gold Contact Option: 0.4 A/ 250 VAC
Electrical Connections: Push-on screw terminals. M20x1.5
with cable strain relief or optional 1/2' NPT connection
Process Connections: 5/16' (7.94 mm) outside diameter
tubing, 1/4' (6.0 mm) inside diameter tubing
Enclosure Rating: NEMA 13, IP54
Mounting Orientation: Vertically, with pressure connections
pointing downwards
Mechanical Working Life: Over 106 switching operations
Weight: 5.6 oz (160 g)
Control System
It has a control system which through a pressure differential
marker actuates the valves, in order to clean the filter catridge.
MANUFACTURER: INGECOAT
PRESSURIZER INSTRUCTIONS
FC-2/200 PRESSURIZER
For the proper functioning of the FC-2/200, is recommended that the air
injection is made to the enclosure through an injection grid double deflection
(horizontal and vertical), with control damper to compensate manually last
air resistance increased by filters. A second control can made by opening
the damper, located off the pipeline of FC-2/200. This damper has been
factory-set to 55 open, suitable for use with completely clean filters.
The pressurizer FC- 2/200 is fully automatic in function of purifying and
pressurizing. Cleaning of filters is performed through a discharge of
compressed air, for which has its own air compressor.
It has 2 electric motors protected by thermal overload relays.
The starting and stopping is done by activating the command switch "A",
black, opening the door panel. The "B" button, green, can run a manual
download each time it is pressed, for voluntary cleaning cartridge filters.
The operation of the pressurizer FC- 2/200 is managed by a small PLC,
brand Lobato. With an open program that can be changed according to the
user's convenience, for which simply seek Ingecoat permission.
For the command cleaning, FC - 2/200 has a DIFFERENTIAL PRESSURE,
identified with the letter "C" in the board. This switch has been set at 2.5 "
wg , or 63 mm water column , so that when the pressure drop of the filter
reaches the specified value , the switch will give way to regular cleaning of
the filters through pulse of
18
17
19
20
14
15
7
13
12
11
10
Equipo Jetpulse
Equipo Aire
Acondicionado Marvair
Retorno de Aire
WWW.INGECOAT.CL
Saturno 1490, Quinta Normal, Santiago - (+56 2) 27271442 - ventas@ingecoat.cl