Beruflich Dokumente
Kultur Dokumente
Sound
DESIGN
Production
of Design
Jehnert
Sound
Car-Audio-Systems
development and
production of
Porsche
Str. 15
Car-Audio-Systems
70794 Filderstadt
part-no. 75145
BMW 3 E 46
instal.instr..part-no. 75145/FH09/03
sedan / Touring
Installation instructions
Heinrich-Hertz-Str. 11
Tel. 00 49 71 58 / 9 56 99-0
70794 Filderstadt
Fax 00 49 71 58 / 9 56 99-10
e-mail: sounddesign@jehnert.de
Tel.: 0711-77 97 87- 87
www.jehnert.com
Fax: 0711-77 78 921
e-mail: sounddesign@jehnert.de
www.jehnert.com
Contents
page
Packing list .......................................................................... 2
1. Disassembly of the door lining .............................................. 3
2. Tweeter installation / see page 7 ........................................ .... 4
3. Panel alignment / reference points ........................................ 5
4. Handling of door lining / Panel installation - Fastening ........... 6
5. Tweeter installation / Loudspeaker cables ............................... 7
6. Insulation of the door lining / car doors ................................. 8
7. Installation of the door lining ................................................ 9
8. Crossover circuit - Speaker connection .................................. 10
Loudspeaker wiring diagram ................................................. 11
9. Installation of the speaker-grills ............................................. 12
Technical information ........................................................... 13
Service / fault diagnoses ....................................................... 14
Guarantee ........................................................................... 15
-1-
Check list
Crossover
(right / left)
Midrange 100 mm Q
Woofer 160 mm
(right / left)
2
2
8
(right / left)
(right / left)
Spax-Screws, 5,0 x 50
Spax-Screws 5,0 x 60
Spax-Screws 5,0 x 70
Hex nut M 4
12
12
Washer 12mm
Washer 20mm
4
16
(f. woofer)
(reserve)
Preassembled hardware:
Velcro fastener plus strips
12
(f. woofer)
16
(8xMR+12xvelcro.)
20
The product was carefully packed and checked for its completeness. If you find anything missing, damaged or
defective, please notice our guarantee services on the back of these assembly instructions.
-2-
B1
B2
A1
A2
-3-
2 . installation of tweeter
- see page 7 -
-4-
3 . Panel alignment
3.1. Place the door lining on a plane surface.
3.2. Dismount the loudspeakers attached to the panel for transport protection.
Retain the screws for later assembly.
3.3. Place the panel without loudspeakers and grill on the door lining and align it:
Check for precise fit of the panel and remove overlapping parts if necessary.
ref.point 1B:
align the cut-out of
the door handle in the
panel exactly (!) below
the door handle
ref.point 1A:
upper edge of the door handle cutout has to be aligned exactly (!) to
the upper and side edge of the door
handle
enlargement
door handle alignment
upper edge of the panel
ref.point 2:
align the back upper edge of the
panel exactly (!) to the moulding of
the side edge of the door-lining
fig.3:
ref.point 3:
enlargement
back side edge of the panel
and side edge of the door-lining
- 5-
Ausschnitt
Mitteltner
CAUTION !
5. Check again for precise fit and remove overlapping parts of the door-lining
all cutting edges of the panel must fit to the door lining snugly
all around without gap
6. screw in the M4 screws supplied with as per 1-6 (see fig.). Screw only hand-tight.
Affix the panel to the door-lining. Secure all screws with washers and nuts
(hexagonal and sheet metal nuts).
7. check again for precise fit ( see page no.5) and tighten the screws.
1
2
M4 x 40
10
see page 9
9
8
M4 x 40
M4 x 50
see page 9
see page 9
M4 x 40
M4 x 40
see page 9
M4 x 50
-6-
5.1. tweeter-installation:
tweeter installation in the original mount mirror triangle:
5.1.1. dismount the original tweeter and unplug the connection cable
5.1.2. install the JEHNERT tweeter with washer and hexagon head
screw M4x8 on the perforated sheet metal
5.1.3. connect tweeter and lead the cable to the cross-over
(length: cross-over in the door build above the
two woofer in the middle - see page10)
5.1.4. Affix perforated sheet metal with the wired tweeter to the
door metal. Screw in the fastening screws of the original tweeter.
-7-
attention danger !!
No insulation behind the
side-airbags (fig. B)
Important:
No insulation material behind
- loudspeaker
- door latch lever
- (fig. A): drill a hole for the
installation clip
fig.: backside of the door lining insulation with our article no.: 27000
Important tip:
the use of 2x16mm mid-woofer /side may cause vibrations which lead to
annoying rattle noises in the car door
open
affix the *backside of the inner door metal with self-adhesive asphalt mats (see fig. * )
by knocking on the car door, vibrations caused by mechanic parts (e.g. Bowden pull wire etc. )
and wiring harness may be found out. Cover these parts with foamed material, felt or
something like that
cut off overlapping cable tie (rattle noise)
adhere felt or foamed material under the original wiring harness
front side of
inner door metal
* door metal outside
= back side of the
inner door metal
-8-
in order to prevent damages of mechanic parts of the car doors, please check
once again the length of all bolts and screws on the back side of the door
lining! No touch with any mechanic parts of the car doors !
(please shorten if necessary).
7.4. carefully screw in the SPAX screws 7-10 through the door panel and
the door lining to the door metal.
observe cables and mechanic parts !
Spax 5,0 x 60
Spax 5,0 x 50
10
Spax 5,0 x 70
7.5. cut out the moisture protection foil (u-form) and stabilize the lateral cutting
edges in order to avoid vibration noise ( e.g. use a packing tape)
-9-
*Important: protect the sheet bar against humidity and observe that the
sheet bar does not touch any metal parts danger of short circuit!
Notice: You
You should
should check
of all
checkthe
thepolarity
polarity
of subwoofers
all woofers after having
before connecting
to crossover
the crossover
circuit
connected
them them
to the
circuit
with a 9 volt battery
with a 9cable
volt battery:
(input
on the side of the amplifier
to
of a 9 Volt battery
of a 9 Volt battery
- 10 -
JEHNERT
DESIGN
midrange
Hig
erform
MADE IN GERMANY
Speaker
DESIGN
Sound
JEHNERT
Tw e e t e r
Hig
Pe
rform
MADE IN GERMANY
Speaker
DESIGN
Sound
JEHNERT
M i d r a n g e
erform
erform
erform
erform
MADE IN GERMANY
Speaker
DESIGN
Sound
JEHNERT
W O O F E R
MADE IN GERMANY
Speaker
JEHNERT
ce
DESIGN
Sound
W O O F E R
MADE IN GERMANY
Speaker
JEHNERT
DESIGN
Sound
W O O F E R
MADE IN GERMANY
Speaker
JEHNERT
DESIGN
Sound
W O O F E R
Hig
Hig
Hig
Hig
input
- 11 -
tweeter
woofer
amplifier
Sound
recommended power
B M W 3 E 4 6 s e d a n / To u r i n g - 7 5 1 4 5
ce
ce
ce
ce
ce
Solution:
grill
2 self-adhesive Velcro-strip
1 Velcro fastener
3 Washer M4 20 as spacer
doorpanel
- 12 -
Te c h n i c a l i n f o r m a t i o n
Equipment:
Model/ year
4-doors
Insulation:
Recommended
amplifier power :
Metal cutwork :
not necessary
3-ways
4 x 160 mm woofer/ side
1 x 100 mm midrange / side
1 x 26 mm tweeter / side
car-customized crossover network
max.continuous Watt/RMS:
car specific frequency range:
Total impedance:
2 x 300/500Watt
49-22.000 Hz
4 Ohm
- 13 -
Dear customer,
We have taken great care to explain the procedures in our installation instructions
more detailed and step by step.
Your tips and suggestions help us for the future to eliminate uncertainties and
misinterpretation.
Therefore, please
inform us. 0049-711-77
what you would like97
to be87-87
improved
Technical questions
Hotline:
page 13)
Development
Mirko Schwarz
amplifier connection
We have taken great care to explain the procedures in our installation instructions
page 8)
detailed
and step by step.
...itmore
doesnt
fit correctly.
door panel customization (
.....grills
dowe
not
hold.still change.
observe notes on
or what
should
page 12!
and
fault
diagnosis
75145Self-help
- BMW 3 E 46
sedan
/ Touring
- 14 -
The following notes serve to help troubleshoot and eliminate faults or malfunctions
on your own. If the following measures are not effective, please call us.
page 13)
page 8)
observe notes on
vibrations
- 14 -
page 12!
7
Guarantee
We grant a manufacturers guarantee of 2 years starting from the date of purchase
of the door panels or sound system from the dealer.
Within this guarantee period to our choice we either repair or replace free of
charge all defects due to material or workmanship.
Exempt from this guarantee are damages due to improper use, wear and tear or
damages which have to be led back on wear or interventions by third parties.
The guarantee does not cover subsequent damages or such defects that only
insignificantly impair the value or the usability of the panels/sound system.
The guarantee does not cover damages due to external influences.
2003/by.AJ/FH
- 15 -