Beruflich Dokumente
Kultur Dokumente
PROJECT REPORT
ON
Project Name
In partial fulfillment of
B Tech VII Semester (Computer Science & Engg.)
Session 20xx-20xx
Submitted To:
Submitted by:
Name of faculty
Designation
Name of Student
VII Semester, B Tech
Certificate
This is to certify that the Project entitled PROJECT TITLE has been carried
out by the student/team of college Jodhpur Institute of Engineering and
Technology, Jodhpur under my guidance and supervision in partial fulfillment
of the degree of Bachelor of Technology in Computer Engineering of Rajasthan
Technical University, Kota during the academic year 20xx-20xx.
Team:
1. Name of the student 1(RTU Roll-No)
2. Name of the student 2(RTU Roll-No)
Date:
Place: JIET, Jodhpur
Signature of Guide
----------------------------------Name of Guide
Designation
Department of CSE
JIET
Signature of H.O.D
-------------------------------------Name of H.O.D
Head Of Department,
Department of CSE,
JIET
Acknowledgment
Name of Student
Date
Abstract
Table of Contents
Certificate..................................................................................................1
Acknowledgment......................................................................................2
Abstract.....................................................................................................3
Table of Contents.....................................................................................4
1. Introduction..........................................................................................5
2. Literature Survey.................................................................................6
3. Requirement Specification..................................................................7
4. Architectural Design............................................................................8
5. Test Planning........................................................................................9
6. Work Distribution..............................................................................10
7. Results..................................................................................................11
8. Conclusion & Future Work...............................................................12
Glossary...................................................................................................13
References...............................................................................................14
1.
Introduction
This section should describe the basic introduction of the project scenario which is going to
be implemented during this lab.
This section should also cover the following points
Technology/Programming Languages/Databases Involved:[Mention the technology, programming languages and Database which you are going to use
during the implementation of the project.]
2. Literature Survey
This section should cover the complete literature details which has been referred during the
execution of the project scenario.
The literature survey should cover the following points
1. Any website which has been referred.
2. The content of the section/chapters of the book which has been referred should be
mentioned here in this section.
3. The content of the section of the papers which has been referred should be mentioned
here in this section.
3. Requirement Specification
Remove the first, second, third page (title page, version tracking, table of content) of
document, also remove references, acronyms, definition section of SRS, except all these
content. Put Complete SRS here.
The following section of SRS document will be mentioned over here.
a. Section 2.0 General Requirements
4. Architectural Design
Remove the first, second, third page (title page, version tracking, table of content) of
document, also remove references, acronyms, definition section of SDD, except all these
content.
Place those section of SDD document which are applicable to your project.
5. Test Planning
Place those section of TPD document which are applicable to your project.
6. Work Distribution
The work distribution during the implementation of the project scenario has to be mentioned
in this section. If more than one student are involved in the project, than each of the student
has to submit the individual implementation plan. Each plan should be in the following below
format.
1.
Name of function/
module
Start Date
End Date
Responsible Person
Mention
the
date
when the
implementa
tion
of
function/
module is
going to be
started.
Mention
the
completion date
for
the
implementation
of
function/
module.
7. Results
This section should contained the following points mentioned below.
Working Snapshots
<Snapshot Title>
Write 1-2 line description of snapshot the paste snapshot here.
<Snapshot Title>
Write 1-2 line description of snapshot the paste snapshot here.
<Snapshot Title>
Write 1-2 line description of snapshot the paste snapshot here.
S.No.
Write
down
the
S.No.
Module
Name
Status
(Pass/Fail)
Error Status
(Fixed/Open)
Remarks
Glossary
Write here the list of Abbreviations and Acronyms in tabular form and definitions of the
terms which need to be described.
References
Mention the reference used in the project
a. Any books which have been referred.
b. Any websites which have been referred.
c. Any source code which have been referred.
d. Any previous year project report which have been referred.
Literature References (IEEE Syntax), Examples are given as under:
a.To refer a research paper - Dinesh Birla, R. P. Maheshwari, and H. O. Gupta, A New
Non-linear Directional Overcurrent Relay Coordination Technique, and Banes and Boons of
Near-end Faults Based Approach, IEEE Transactions on Power Delivery, vol.-21,no.-3, pp.
1176-1182, July 2006
b.To refer a book - David E, Goldberg, Genetic Algorithms in Search, Optimization, and
Machine Learning, ISBN 81-7808-130-X, Pearson Education Asia Pty Ltd., 2000.
(621.381952,G47G)