Beruflich Dokumente
Kultur Dokumente
Edward Valves
Edward Valves
Edward Valves
1900 South Saunders Street
Raleigh, North Carolina 27603 USA
US Sales Offices
Phone:
919- 832- 0525
Facsimile: 919- 831- 3369
Facsimile: 919- 831- 3376
Visit Our Website
www. edwardvalves. com
While the information and specifications contained in this literature are believed to be accurate, they are supplied for informative purposes only and should not be
considered certified or as a guarantee of satisfactory results by reliance thereon. Nothing contained herein is to be construed as a warranty or guarantee, express
or implied, regarding any matter with respect to this product. Because Flowserve is continually improving and upgrading its product design, the specifications,
dimensions and information contained herein are subject to change without notice. Should any question arise concerning these provisions, the purchaser/user
should contact Flowserve Corporation at any one of its worldwide operations or offices.
Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this Flowserve product is
designed to perform its intended function safely during its useful life. However, the purchaser or user of Flowserve products should be aware that Flowserve
products might be used in numerous applications under a wide variety of industrial service conditions. Although Flowserve can (and often does) provide general
guidelines, it cannot provide specific data and warnings for all possible applications. The purchaser/user must therefore assume the ultimate responsibility for the
proper sizing and selection, installation, operation, and maintenance of Flowserve products. The purchaser/user should read and understand the Installation
Operation Maintenance (IOM) instructions included with the product, and train its employees and contractors in the safe use of Flowserve products in connection
with the specific application.
Edward Valves
EV100
5th Edition
FLOWSERVE CORPORATION
FLOW CONTROL DIVISION
Edward Valves Operations
1900 South Saunders Street
Raleigh, North Carolina 27603
USA
Phone:
919- 832- 0525
Facsimile: 919- 831- 3369
Facsimile: 919- 831- 3376
www. edwardvalves. com
Edward Valves
2002 Flowserve Corporation, Irving, Texas, USA. Flowserve and Edward Valves are registered trademarks of Flowserve Corporation.
Edward Valves
EV100
5th Edition
Introduction
Accessories/Actuators
Technical
Maintenance
Edward Valves
Table of Contents
Introduction
History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page No.
A-2
Accessories/Acutators
B-2
B-6
B-8
B-11
B-15
B-18
B-21
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Blow Off Valves. . . . . . . . . . . . . . . . . . . . . . . . . .
Elbow Down Valves . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Valves . . . . . . . . . . . . . . . . . . . . . . . . .
Series 1500 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Strainers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flanged 1500 Univalves . . . . . . . . . . . . . . . . . . . .
PressurCombo . . . . . . . . . . . . . . . . . . . . . . . . . .
Hermavalve (Commercial) . . . . . . . . . . . . . . . . . .
F-2
F-5
Technical Section:
1.0
1.1
1.2
1.3
C-2
C-4
C-5
C-6
C-8
C-11
C-17
C-20
C-28
C-31
C-40
C-43
C-53
C-56
C-59
C-68
C-71
1.4
D-2
D-4
D-9
D-10
D-12
D-18
D-19
D-20
D-24
Page No.
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.0
2.1
G-4
G-4
G-10
G-14
G-19
Flow Performance . . . . . . . . . . . . . . . . . . . .
Choose the Best Valve Size for Your
Service Conditions . . . . . . . . . . . . . . . . . . .
Basic Calculations. . . . . . . . . . . . . . . . . . . .
Corrections Required with
Large Pressure Drops . . . . . . . . . . . . . . . . .
Check Valve Sizing . . . . . . . . . . . . . . . . . . .
Pipe Reducer Coefficients . . . . . . . . . . . . . .
G-26
G-28
G-30
3.1
3.2
3.3
3.4
3.5
G-59
G-59
G-59
G-60
G-61
G-61
4.0
G-62
2.2
2.3
2.4
2.5
3.0
G-23
G-23
G-23
G-58
H-2
H-3
H-29
Maintenance
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nuclear
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hermavalve . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Univalve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bolted Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas-Hydraulic Actuators . . . . . . . . . . . . . . . . . . . .
Controlled Closure. . . . . . . . . . . . . . . . . . . . . . . .
J-2
E-2
E-4
E-8
E-10
E-13
E-14
Page No.
ii
III
Forged Steel
Availability Chart
IV
Description of Figure
Number System
VI
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
158
158Y
160
160Y
238
238Y
303
303Y
304
304Y
318
318Y
319
319Y
329
329Y
338
338Y
391
391Y
394
394Y
393
393Y
602
602Y
604
604Y
605
605Y
606
606Y
607
607Y
614
614Y
616
616Y
617
617Y
618
618Y
619
619Y
670Y
690
690Y
691
691Y
692
692Y
694
694Y
695
695Y
702Y
706Y
707Y
714Y
716Y
717Y
770Y
792Y
794Y
795Y
828
829
832
832Y
PAGE NO.
D-10
D-10
D-11
D-11
D-18
D-18
C-13
C-13
C-13
C-13
C-11
C-11
C-11
C-11
C-11
C-11
D-18
D-18
C-15
C-15
C-15
C-15
C-15
C-15
C-25
C-25, 29
C-24
C-24
C-24
C-24
C-24
C-24
C-24
C-24
C-21
C-21, 28
C-20
C-20
C-20
C-20
C-20
C-20
C-20
C-20
C-26, 27
C-26
C-26
C-26
C-26
C-26, 27
C-26, 27, 30
C-26
C-26
C-26
C-26
C-25, 29
C-24
C-24
C-21, 28
C-20
C-20
C-26, 27
C-26, 27, 30
C-26
C-26
B-8
B-8
B-14
B-14
FIGURE NO.
838
838Y
846
847
848
848Y
849
849Y
858
868
868Y
869
869Y
970Y
1028
1029
1032
1032Y
1038
1038Y
1046
1047
1048
1048Y
1049
1049Y
1058
1068
1068Y
1069
1069Y
1302
1302Y
1314
1314Y
1324
1324Y
1390
1390Y
1392
1392Y
1441
1441Y
1443
1443Y
1570Y
1611
1611BY
1611Y
1641
1641Y
1643
1643Y
1711BY
1711Y
1911
1911BY
1911Y
2002Y
2006Y
2007Y
2014Y
2016Y
2017Y
2070Y
2092Y
2094Y
2095Y
2570Y
PAGE NO.
B-13
B-13
B-9
B-9
B-11
B-11
B-11
B-11
B-10
B-12
B-12
B-12
B-12
C-37, 38
D-12
D-12
D-17
D-17
D-16
D-16
D-14
D-14
D-13
D-13
D-13
D-13
D-16
D-15
D-15
D-15
D-15
C14
C14, 18
C-12
C-12, 17
C-12
C-12
C-16
C-16
C-16
C-16, 19
D-4, 5
D-4, 5
D-4, 5
D-4, 5
C-52
C-22, 23
C-22, 23
C-22, 23
D-6, 7
D-6, 7
D-6, 7
D-6, 7
C-22, 23
C-22, 23
C-33
C-33, 34
C-33
C-47, 48, 54
C-47
C-47, 48
C-43, 44, 53
C-43
C-43, 44
C-52
C-49, 51, 55
C-49, 50
C-49, 50
C-62, 64
FIGURE NO.
3902Y
3906
3906Y
3907
3907Y
3914Y
3916
3916Y
3917
3917Y
3992Y
3994
3994Y
3995
3995Y
4002
4002Y
4006
4006Y
4007
4007Y
4014
4014Y
4016
4016Y
4017
4017Y
4092
4092Y
4094
4094Y
4095
4095Y
4302Y
4306Y
4307Y
4314Y
4316Y
4317Y
4370Y
4392Y
4394Y
4395Y
4402Y
4406Y
4407Y
4414Y
4416Y
4417Y
4448Y
4470Y
4492Y
4494Y
4495Y
4498Y
4502Y
4514Y
4570Y
4592Y
5002Y
5014Y
5070Y
5092Y
5158
5160
7502Y
7506
7506Y
7507
PAGE NO.
C-60, 61, 66
C-60
C-60
C-60, 61
C-60, 61
C-56, 57, 65
C-56
C-56
C-56, 57
C-56, 57
C-62, 63, 67
C-62
C-62
C-62, 63
C-62, 63
C-35, 36
C-35, 36, 41
C-35
C-35
C-35, 36
C-35, 36
C-31, 32
C-31, 32, 40
C-31
C-31
C-31, 32
C-31, 32
C-37, 39
C-37, 39, 42
C-37
C-37
C-37, 38
C-37, 38
C-35, 36, 41
C-35
C-35, 36
C-31, 32, 40
C-31
C-31, 32
C-37, 38
C-37, 39, 42
C-37
C-37, 38
C-60, 61, 66
C-60
C-60, 61
C-56, 57, 65
C-56
C-56, 57
D-9
C-62, 64
C-62, 63, 67
C-62
C-62, 63
D-9
C-69
C-68
C-71
C-70
C-69
C-68
C-71
C-70
D-10
D-11
C-47, 48, 54
C-47
C-47
C-47, 48
FIGURE NO.
7507Y
7514Y
7516
7516Y
7517
7517Y
7548Y
7592Y
7594
7594Y
7595
7595Y
7598Y
9158
9160
11511
11511Y
11511BY
12011Y
12011BY
12511
12511Y
12511BY
14311Y
14311BY
14411BY
14411Y
15004
15008
15014
15018
15104
15108
15114
15118
16004
16008
16014
16018
35125
35129
35225
35229
36120
36122
36124
36125
36128
36129
36160
36164
36165
36168
36169
36170
36174
36175
36178
36179
36220
36222
36224
36225
36228
36229
36260
36264
36265
36268
PAGE NO.
C-47, 48
C-43, 44, 53
C-43
C-43
C-43, 44
C-43, 44
D-9
C-49, 51, 55
C-49, 50
C-49, 50
C-49, 50
C-49, 50
D-9
D-10
D-11
C-45
C-45
C-45, 46
C-45
C-45, 46
C-58
C-58
C-58, 59
C-33
C-33, 34
C-58, 59
C-58
E-6
E-6
E-6
E-6
E-6
E-6
E-6
E-6
D-27
D-27
D-27
D-27
D-28
D-28
D-28
D-28
B-15
D-19
B-15 & D-8
B-24
B-15 & D-8
B-24
B-16
B-16
B-25
B-16
B-25
B-17
B-17
B-26
B-17
B-26
B-15
D-19
B-15 & D-8
B-24
B-15 & D-8
B-24
B-16
B-16
B-25
B-16
FIGURE NO.
36269
36270
36274
36275
36278
36275
36279
66120
66124
66125
66128
66129
66160
66164
66165
66168
66169
66170
66174
66175
66178
66179
66220
66224
66225
66228
66229
66260
66264
66265
66268
66269
66270
66274
66275
66278
66279
96124
96128
96164
96168
96174
96178
96224
96228
96264
96268
96274
96278
A1611
A1611Y
A1911
A1911Y
DSXXXX
DEXXXX
DCXXXX
PAGE NO.
B-25
B-17
B-17
B-24
B-17
B-26
B-26
B-18
B-18 & D-8
B-27
B-18 & D-8
B-27
B-19
B-19
B-28
B-19
B-28
B-20
B-20
B-29
B-20
B-29
B-18
B-18 & D-8
B-27
B-18 & D-8
B-27
B-19
B-19
B-28
B-19
B-28
B-20
B-20
B-29
B-20
B-29
B-21
B-21
B-22
B-22
B-23
B-23
B-21
B-21
B-22
B-22
B-23
B-23
C-22
C-22
C-33
C-33
D-21, 22, 23
D-21, 22, 23
D-21, 22, 23
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
iii
Edward Valves
PRESSURE RATING*(1)
SIZE(1)
ANSI 600(110)
Flanged
ENDS
PAGE NO.
B-8
ANSI 800(130)
Threaded, Socket
B-11
Series 1500
D-12 & 13
B-15
Univalve
Globe Stop Valves
Hermavalve
Globe Stop Valves
ANSI to 1690(290)
& 4500(760)
B-18
B-21
1/2(15) thru
Socket, Buttwelding
2-1/2(65)
D-27
E-6
& 600(110)
1-1/2(40) thru
2-1/2(65)
ANSI 600(110)
Flanged
B-9
ANSI 800(130)
Threaded, Socket
B-12
Series 1500
D-14 & 15
B-16
Univalve Globe
Stop-Check Valves
&4500(760)
B-19
B-22
ANSI 600(110)
Flanged
B-10
ANSI 800(130)
Threaded, Socket
B-13
Series 1500
B-22
B-17
Univalve
Piston Check Valves
Hydraulic Check
Valves
Ball Check Valves
& 4500(760)
5,000 PSI CWP
B-23
1/4(6) thru 2(50)
Threaded, Socket
D-11
Strainers
B-20
ANSI 800(130)
B-14
D-17
Threaded, Socket
D-18
Series 1500
Flanged Univalve
Class 1500
Flanged
Univalve Angle
Stop, Stop-Check
& Check Valves
ANSI 1690
ANSI 2680
Socket, Buttwelding
D-19
B-24 thru
B29
See paragraph 3.2, page G-59 or definition of various pressure ratings available.
(1) Metric equivalent values for ratings and sizes are in parentheses.
iv
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Flite-Flow
Piston Check Valves
Tilting Disk
Check Valves
Nuclear Valves
Special Application Valves
PRESSURE RATING*(1)
ANSI 300(50)
SIZE(1)
2-1/2(65) thru 12(300)
ENDS
ANSI 600(110)
ANSI 600(110)
ANSI 900(150)
ANSI 600(110)
ANSI 900(150)
ANSI 1500(250) & 2500(420)
ANSI 600(110) & 900(150)
ANSI 1500(260) & 2500(420)
ANSI 300(50)
ANSI 400(68)
ANSI 600(110)
ANSI 700(120)
ANSI 900(150)
ANSI 1100(190)
Buttwelding
C-38, 52, 64
Class 4500(760)
Thru ANSI 2500(420)
Thru ANSI 2500(420)
Buttwelding
As Required
C-71
E-2 thru 14
D-3 & 9
Buttwelding
or Flanged
Buttwelding
or Flanged
Buttwelding
or Flanged
Buttwelding
or Flanged
Buttwelding
or Flanged
Buttwelding
or Flanged
PAGE NO.
C-11, 13 & 15
C-20, 24, 26
C-20, 24
C-31, 32, 35, 36
C-43, 44, 47, 48, 56,
57, 60, 61
C-26
C-37
C-49, 50, 62, 63
C-22, 23, 33, 34
C-45, 46, 58, 59
C-12 & 14
C-17 & 18
C-21, 25
C-28, 29
C-32, 35, 36
C-40, 41
C-43, 44, 47, 48,
56, 57, 60, 61
C-53, 54, 65, 66
C-68, 69
C-16
C-19
C-27
C-30
C-37, 39
C-42
C-49, 51, 62, 63
C-55, 67
C-70
C-27
* See paragraph 3.2, page G-59 for definition of various pressure ratings available.
(1) Metric equivalent values for ratings and sizes are in parentheses.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
F11 -
F22 -
F91 -
F347H LF2 -
BC-
FF -
M - Motor actuated.
ML - Valve less actuator but with motor
actuator mounting equipment.
MM -
N-
plating.
R-
S-
XY-
T1 T2 T3 T4 -
T5 -
LD - Impactorgear or Impactodrive.
WCC -
C12A -
XX
1 Alpha Digit Indicates Design Revision if Applicable.
2 Alpha Digits Indicates Style of Pressure Combo Valve
(See Page D20).
XXXXX
3-5 Digits Figure Number
(XXX)
3-4 Digits Body Material Designation
Unless otherwise specified when ordering Edward valves, the standard material of construction for
Forged products is A105 Carbon Steel, and for Cast products is A216 Grade WCB Carbon Steel.
Listed below are the letter suffixes used to indicate variations from standard construction, or special
features (Ex. 618K, 7506 [WC6]Y, and 847 AH.)
When two or more suffixes follow a figure number a definite suffix sequence is to be used.
The sequence is:
1) Special material (if applicable)
2) All other applicable feature suffixes in alphabetical order.
Except T1-T5 which are listed last.
XXXXXXX
1 or more Digits As Required Suffixes (See List)
vi
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
EV100
5th Edition
Introduction
Edward Valves
High Performance
For Critical Service
Temperatures that can exceed 1000 F. Pressures
surpassing 10,000 psi. In critical service conditions, you
cant take chances. You dont just meet standards, you
exceed them. Thats how Edward forged and cast steel
valves have become the specified choice for power plants,
process facilities, and other high-temperature, highpressure services.
Conservative Design
Edward Valves takes a conservative approach
to valve design. We meet all applicable codes
and standards, but we go beyond that...with
finite element stress analysis of critical areas
and rigorous proof testing. Edward valves are
built to take punishment!
And our extensive testing has also allowed us
to develop extremely high flow efficiencies in
all our valves.
Precision Manufacturing
Edward Valves also exceeds industry
standards on the factory floor. Our forged
valves are produced on a fully automated line,
with CNC machining centers providing precise
process control. And we maximize cast steel
quality by producing our valve body castings
using a directional solidification process from
patterns designed by our own technicians.
This process assures high strength void free
castings for uncompromised quality.
A2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
A3
Edward Valves
A History of Firsts
A4
Feature
Benefit
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
EV100
5th Edition
A
Forged Steel Valves
Edward Valves
8.
9.
10.
2.
3.
11.
12.
4.
5.
6.
2. Yoke bushing material has low coefficient of friction which substantially reduces torque and stem
wear and eliminates galling. Mechanical upset locks
yoke bushing to yoke.
B2
8. Threaded bonnet has ACME threads for resistance to galling and ease of disassembly. Unwelded
models utilize a graphitic gasket for dependable
sealing. Welded models employ a fillet weld (canopy
weld on stainless steel valves) for absolute protection from body-bonnet leakage.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
ASTM NO.
ASTM NO.
ASTM NO.
ASTM NO.
A-105
A-182
A-182
A-182
Grade F-22
Grade F-316/F-347*
Grade F91
A-696
A-739
A-479
A-182
Grade C
Grade B-22
T-316/347
Grade F91
A-479
A-479
A-638
A-638
T-410CL3
T-410CL3
Grade 660
Grade 660
A-732
A-732
A-732
A-732
Grade 21
Grade 21
Grade 21
Grade 21
Body Seat
Stellite 21
Stellite 21
Stellite 21
Stellite 21
Junk Ring
A-732
Grade 21
Stem
Disk
Packing Rings
Gland
Gland Adjusting Screw
Yoke
Yoke Bushing
Yoke Bolt
Yoke Nut
A-668
A-668
A-182
A-668
Grade 4140
Grade 4140
Grade F6a
Grade 4140
A-582
A-582
A-582
A-582
T-416
T-416
T-416
T-416
A-181
A-181
A-181
A-181
Class 70
Class 70
Class 70
Class 70
A-307
A-307
A-307
A-307
Grade A
Grade A
Grade A
Grade A
A-563 Grade A
A-563 Grade A
A-563 Grade A
A-563 Grade A
Malleable or
Malleable or
Malleable or
Malleable or
Adapter
Ductile Iron
Ductile Iron
Ductile Iron
Ductile Iron
Mild Steel
Mild Steel
Mild Steel
Mild Steel
Plated
Plated
Plated
Plated
Flexible
Flexible
Flexible
Flexible
Graphite
Graphite
Graphite
Graphite
A-582
A-582
A-479
A-582
T-416
T-416
T-316
T-416
Locking Collar
Carbon
Carbon
Carbon
Carbon
Steel
Steel
Steel
Steel
Spring
A-313
A-313
A-313
INCONEL
T-302
T-302
T-302
X-750
Handwheel/Impactor Handle
Stem Nut/Washer
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B3
Edward Valves
B4
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A
B
Figure 1
First, a Stellite wire is inserted into a hole in a
Univalve body guided disk.
Figure 2
Next, the Stellite wire is fed around circular
grooves, adjacent to one another, on the inside
bore of the disk and outside diameter of the stem.
Figure 3
Finally the hole through which the wire was fed is
welded closed.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B5
Edward Valves
B6
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
DESCRIPTION
Body/Bonnet
Disk
Body Seat
Stem
Cap Screws
Gasket
Packing
Gland
Yoke Bushing
Handwheel/Handle
Stem Nut
Eye Bolt
Eye Bolt Nut
Eye Bolt Pin
Spring**
Ball**
BOLTED BONNET
ASTM NO.
ASTM NO.
A-105
A-182
Grade F11
AISI 615
AISI 615
Stainless Steel
Stainless Steel
Stellite 21
Stellite 21
A-582
A-582
T-416
T-416
A-193
A-193
Grade B-7
Grade B-7
Spiral Wound
Spiral Wound
Non Asbestos
Non-Asbestos
A-536
A-536
GR. 80-55-06
GR. 80-55-06
Malleable or
Malleable or
Ductile Iron
Ductile Iron
Mild Steel-Plated
Mild Steel-Plated
A-582
A-582
T-416
T-416
A-563
A-563
Grade A
Grade A
AISI
AISI
Grade 4140
Grade 4140
A-313
A-313
T302
T302
A-276
A-276
T440 C
T440 C
A
B
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B7
Edward Valves
Stop Valves Class 600 1480 PSI @ 100F (102.1 BAR @ 38C)
Standard Features
B8
FIG. NO.
828
829
TYPE
Globe
Angle
ENDS
Flanged
Flanged
NPS (DN)
1/2 (15) thru
2 (50)
NPS
DN
1/2
15
6.5
165
3.3
84
6.1
155
5.7
145
3.8
97
7.5
3.4
7
3.2
3/4
20
7.5
191
3.8
97
6.9
175
6.4
163
4.3
109
12
5.4
11
5
1
25
8.5
216
4.3
109
7.7
196
7.1
180
4.8
122
16
7.2
15
6.8
1-1/4
32
9.5
241
4.8
122
11.1
282
10.2
259
7.1
180
27
12.2
26
11.7
1-1/2
40
9.5
241
4.8
122
11.1
282
10.2
259
7.1
180
32
14.4
31
14
2
50
11.5
292
5.8
147
12.1
307
11.0
279
8.5
216
38
17.1
36
16.2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop-Check Valves Class 600 1480 PSI @ 100F (102.1 BAR @ 38C)
A
B
Standard Features
FIG. NO.
846
847
TYPE
Globe
Angle
ENDS
Flanged
Flanged
NPS (DN)
1/2 (15) thru
2 (50)
NPS
DN
1/2
15
6.5
165
3.3
84
6.1
155
5.7
145
3.8
97
7.5
3.4
7
3.2
3/4
20
7.5
191
3.8
97
6.9
175
6.4
163
4.3
109
12
5.4
11
5
1
25
8.5
216
4.3
109
7.7
196
7.1
180
4.8
122
16
7.2
15
6.8
1-1/4
32
9.5
241
4.8
122
11.1
282
10.2
259
7.1
180
27
12.2
26
11.7
1-1/2
40
9.5
241
4.8
122
11.1
282
10.2
259
7.1
180
32
14.4
31
14
2
50
11.5
292
5.8
147
12.1
307
11.0
279
8.5
216
38
17.1
36
16.2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B9
Edward Valves
Piston Check Valves Class 600 1480 PSI @ 100F (102.1 BAR @ 38C)
Standard Features
B10
FIG. NO.
858
TYPE
Globe
ENDS
Flanged
NPS (DN)
1/2 (15) thru 2 (50)
Dimensions - Globe
Figure No. 858
NPS
DN
1/2
15
6.5
165
2.3
58
6.5
2.9
3/4
20
7.5
191
2.7
69
11
5
1
25
8.5
216
3.1
79
13
5.9
1-1/4
32
9.5
241
4.2
107
21
9.5
1-1/2
40
9.5
241
4.2
107
26
11.7
2
50
11.5
292
4.7
119
29
13.1
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves Class 800 2000 PSI @ 100F (137.9 BAR @ 38C)
A
B
Standard Features
ENDS
Threaded
Socket Welding
Threaded
Socket Welding
NPS (DN)
1/4 (8)
thru
2 (50)
TYPE
Y-Pattern
Y-Pattern
Angle
Angle
NPS
DN
1/4
8
3
76
1.5
38
6
152
5.7
145
3.8
97
4
1.8
4
1.8
3/8
10
3
76
1.5
38
6
152
5.7
145
3.8
97
4
1.8
4
1.8
1/2
15
3
76
1.5
38
6
152
5.7
145
3.8
97
4
1.8
4
1.8
3/4
20
3.6
91
1.8
46
6.8
173
6.4
163
4.3
109
5.5
2.5
5.5
2.5
1
25
4.3
109
2
51
7.6
193
7.1
180
4.8
122
7.5
3.4
7
3.2
1-1/4
32
5.8
147
2.9
74
10.9
277
10.2
259
7.1
180
16
7.2
17
7.7
1-1/2
40
5.8
147
2.9
74
10.9
277
10.2
259
7.1
180
16
7.2
17
7.7
2
50
6.5
165
3.3
84
12.1
307
11
279
8.5
216
23
10.4
24
10.8
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B11
Edward Valves
Stop-Check Valves Class 800 2000 PSI @ 100F (137.9 BAR @ 38C)
Standard Features
B12
NPS
DN
ENDS
Threaded
Socket Welding
Threaded
Socket Welding
NPS (DN)
1/4 (8)
thru
2 (50)
TYPE
Y-Pattern
Y-Pattern
Angle
Angle
1/4
8
3
76
1.5
38
6
152
5.7
145
3.8
97
4
1.8
4
1.8
3/8
10
3
76
1.5
38
6
152
5.7
145
3.8
97
4
1.8
4
1.8
1/2
15
3
76
1.5
38
6
152
5.7
145
3.8
97
4
1.8
4
1.8
3/4
20
3.6
91
1.8
46
6.8
173
6.4
163
4.3
109
5.5
2.5
5.5
2.5
1
25
4.3
109
2
51
7.6
193
7.1
180
4.8
122
7.5
3.4
7
3.2
1-1/4
32
5.8
147
2.9
74
10.9
277
10.2
259
7.1
180
16
7.2
17
7.7
1-1/2
40
5.8
147
2.9
74
10.9
277
10.2
259
7.1
180
16
7.2
17
7.7
2
50
6.5
165
3.3
84
12.1
307
11
279
8.5
216
23
10.4
24
10.8
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A
B
Standard Features
A - End to End
E - Center to Top
Weight
ENDS
Threaded
Socket Welding
NPS (DN)
1/4 (8) thru
2 (50)
Dimensions - Globe
Figure No. 838/838Y
TYPE
Y-Pattern
Y-Pattern
NPS
DN
1/4
8
3
76
2.8
71
2
.9
3/8
10
3
76
2.8
71
2
.9
1/2
15
3
76
2.8
71
2
.9
3/4
20
3.6
91
3.3
84
3.5
1.6
1
25
4.3
109
3.8
97
5
2.3
1-1/4
32
5.8
147
4.6
117
11
5
1-1/2
40
5.8
147
4.6
117
10
4.5
2
50
6.5
165
5.1
130
14
6.3
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B13
Edward Valves
Standard Features
A - End to End
E - Center to Top
Weight
B14
ENDS
Threaded
Socket Welding
NPS (DN)
1/4 (8) thru
2 (50)
Dimensions - Globe
Figure No. 832/832Y
TYPE
Y-Pattern
Y-Pattern
NPS
DN
1/4
8
3
76
2.8
71
2
.9
3/8
10
3
76
2.8
71
2
.9
1/2
15
3
76
2.8
71
2
.9
3/4
20
3.6
91
3.3
84
3.5
1.6
1
25
4.3
109
3.8
97
5
2.3
1-1/4
32
5.8
147
4.6
117
11
5
1-1/2
40
5.8
147
4.6
117
10
4.5
2
50
6.5
165
5.1
130
14
6.4
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A
B
Standard Features
Available Body Materials
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or welded bonnet.
OS & Y.
Y-Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Integral backseat.
Asbestos free graphitic packing.
UNWELD.
36120
36124
36128
36220
36224
36228
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
B - Center to End
E - Center to Top, (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
* Impactor Handle
ENDS
NPS (DN)
Y-Pattern
Y-Pattern
Y-Pattern
Threaded
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. 36120, 36124, 36128
36220,36224,36228
TYPE
NPS
DN
1/2
15
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
3/4
20
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
1
25
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
1-1/4
32
6.7
170
3.20
81
11.0
279
4.8
122
15.9
404
14.3*
363*
36
16
38
17
1-1/2
40
6.7
170
3.20
81
11.0
279
4.8
122
15.9
404
14.3*
363*
36
16
38
17
2
50
8.2
208
3.64
92
11.6
295
6.1
155
17.7
450
14.3*
363*
57
26
59
27
2-1/2
65
10.7
272
4.00
102
12.5
318
7.1
180
19.6
498
16.0**
406**
100
46
104
47
3
80
10.7
272
4.00
102
12.5
318
7.1
180
19.6
498
16.0**
406**
100
46
104
47
4
100
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
138
63
142
64
**Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B15
Edward Valves
Standard Features
Available Body Materials
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or welded bonnet.
OS & Y.
Y-Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Integral backseat.
Asbestos free graphitic packing.
UNWELD.
36160
36164
36168
36260
36264
36268
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
B - Center to End
E - Center to Top, (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
* Impactor Handle
B16
ENDS
NPS (DN)
Y-Pattern
Y-Pattern
Y-Pattern
Threaded
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. 36160, 36164, 36168,
36260, 36264, 36268
TYPE
NPS
DN
1/2
15
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
3/4
20
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
1
25
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
1-1/4
32
6.7
170
3.20
81
11.0
279
4.8
122
15.9
404
14.3*
363*
36
16
38
17
1-1/2
40
6.7
170
3.20
81
11.0
279
4.8
122
15.9
404
14.3*
363*
36
16
38
17
2
50
8.2
208
3.64
92
11.6
295
6.1
155
17.7
450
14.3*
363*
57
26
59
27
2-1/2
65
10.7
272
4.00
102
12.5
318
7.1
180
19.6
498
16.0**
406**
100
46
104
47
3
80
10.7
272
4.00
102
12.5
318
7.1
180
19.6
498
16.0**
406**
100
46
104
47
4
100
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
138
63
142
64
**Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
B
Standard Features
Available Body Materials
A105 carbon steel.
Pressure Class 1690
F22 alloy steel.
F91 alloy steel.
FIG. NO.
TYPE
WELDED UNWELD.
F316, F347 stainless steel.
36170
36270
Y-Pattern
Other material on application.
36174
36274
Y-Pattern
Unwelded (graphitic seal) or welded cover.
36178
36278
Y-Pattern
Y-Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Stainless steel spring. (Optional without springs, see page G-14.)
A - End to End
AA - End Hub Diameter
B - Center to End
E - Center to Top
Weight
ENDS
NPS (DN)
Threaded
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. 36170, 36174, 36178,
36270, 36274, 36278
(PN 290)
NPS
DN
1/2
15
6.0
152
2.30
58
4.0
102
3.9
99
14
6
3/4
20
6.0
152
2.30
58
4.0
102
3.9
99
14
6
1
25
6.0
152
2.30
58
4.0
102
3.9
99
14
6
1-1/4
32
6.7
170
3.20
81
4.8
122
5.0
127
22
10
1-1/2
40
6.7
170
3.20
81
4.8
122
5.0
127
22
10
2
50
8.2
208
3.64
92
6.1
155
5.8
147
31
14
2-1/2
65
10.7
272
4.00
102
7.1
180
7.2
183
44
20
3
80
10.7
272
4.00
102
7.1
180
7.2
183
44
20
4
100
12.8
325
4.80
122
8.8
224
7.8
198
86
39
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B17
Edward Valves
Univalve Stop Valves Class 2680 6700 PSI @ 100F (462.1 BAR @ 38C)
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or welded bonnet.
OS & Y.
Y-Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Integral backseat.
Asbestos free graphitic packing.
UNWELD.
66120
66124
66128
66220
66224
66228
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
B - Center to End
E - Center to Top, (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
* Impactor Handle
B18
NPS
DN
ENDS
NPS (DN)
Y-Pattern
Y-Pattern
Y-Pattern
Threaded*
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. 66120, 66124, 66128,
66220, 66224, 66228
TYPE
1/2
15
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
3/4
20
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
1
25
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
** Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A
B
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application
Unwelded (graphitic seal) or welded bonnet.
OS & Y.
Y-Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Integral backseat.
Asbestos free graphitic packing.
UNWELD.
66160
66164
66168
66260
66264
66268
TYPE
ENDS
NPS (DN)
Y-Pattern
Y-Pattern
Y-Pattern
Threaded*
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. 66160, 66164, 66168,
66260, 66264, 66268
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
B - Center to End
E - Center to Top, (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
* Impactor Handle
NPS
DN
1/2
15
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
3/4
20
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
1
25
6.0
152
2.30
58
7.5
191
4.0
102
11.5
292
8.5
216
19
9
20
9
1-1/4
32
6.7
170
3.20
81
9.8
249
4.8
122
14.6
371
11.0*
279*
34
16
36
17
1-1/2
40
6.7
170
3.20
81
9.8
249
4.8
122
14.6
371
11.0*
279*
34
16
36
17
2
50
10.7
272
4.00
102
11.6
295
7.1
180
18.6
472
14.3*
363*
79
36
83
38
2-1/2
65
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
142
65
146
66
3
80
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
142
65
146
66
4
100
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
142
65
146
66
**Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B19
Edward Valves
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or welded cover.
Y-Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Stainless steel spring.
(Optional without springs, see page G14.)
UNWELD.
66170
66174
66178
66270
66274
66278
A - End to End
AA - End Hub Diameter
B - Center to End
E - Center to Top, (Open)
Weight
B20
ENDS
NPS (DN)
Y-Pattern
Y-Pattern
Y-Pattern
Threaded*
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. 66170, 66174, 66178,
66270, 66274, 66278
TYPE
NPS
DN
1/2
15
6.0
152
2.30
58
4.0
102
3.9
99
14
6
3/4
20
6.0
152
2.30
58
4.0
102
3.9
99
14
6
1
25
6.0
152
2.30
58
4.0
102
3.9
99
14
6
1-1/4
32
6.7
170
3.20
81
4.8
122
5.0
127
22
10
1-1/2
40
6.7
170
3.20
81
4.8
122
5.0
127
22
10
2
50
10.7
272
4.00
102
7.1
180
7.0
178
52
24
2-1/2
65
12.8
325
4.80
122
8.8
224
7.8
198
86
39
3
80
12.8
325
4.80
122
8.8
224
7.8
198
86
39
4
100
12.8
325
4.80
122
8.8
224
7.8
198
86
39
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
=
B
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or welded bonnet.
OS & Y.
Y-Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Integral backseat.
Asbestos free graphitic packing.
UNWELD.
96124
96128
96224
96228
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
B - Center to End
E - Center to Top, (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
ENDS
NPS (DN)
Y-Pattern
Y-Pattern
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. 96124, 96128
96224, 96228
TYPE
NPS
DN
1/2
15
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
3/4
20
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
1
25
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
1-1/4
32
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
1-1/2
40
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
2
50
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
158
72
162
74
2-1/2
65
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
158
72
162
74
3
80
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
158
72
162
74
4
100
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
158
72
162
74
** Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B21
Edward Valves
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or welded bonnet.
OS & Y.
Y-Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Integral backseat.
Asbestos free graphitic packing.
UNWELD.
96164
96168
96264
96268
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
B - Center to End
E - Center to Top, (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
ENDS
NPS (DN)
Y-Pattern
Y-Pattern
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. 96164, 96168,
96264, 96268
TYPE
NPS
DN
1/2
15
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
3/4
20
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
1
25
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
1-1/4
32
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
1-1/2
40
8.2
208
3.64
92
7.3
185
6.1
155
13.4
340
8.5
216
43
20
45
21
2
50
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
158
72
162
74
2-1/2
65
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
158
72
162
74
3
80
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
158
72
162
74
4
100
12.8
325
4.80
122
11.2
284
8.8
224
20.0
508
16.0**
406**
158
72
162
74
** Impactor Handwheel
B22
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or welded cover.
Y-Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Stainless steel spring.
(Optional without springs, see page G14.)
B
Pressure Class 4500 (PN 760)
FIG. NO.
WELDED
UNWELD.
96174
96178
96274
96278
TYPE
ENDS
NPS (DN)
Y-Pattern
Y-Pattern
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. 96174, 96178,
96274, 96278
A - End to End
AA - End Hub Diameter
B - Center to End
E - Center to Top
Weight
NPS
DN
1/2
15
8.2
208
3.64
92
6.1
155
5.4
137
35
16
3/4
20
8.2
208
3.64
92
6.1
155
5.4
137
35
16
1
25
8.2
208
3.64
92
6.1
155
5.4
137
35
16
1-1/4
32
8.2
208
3.64
92
6.1
155
5.4
137
35
16
1-1/2
40
8.2
208
3.64
92
6.1
155
5.4
137
35
16
2
50
12.8
325
4.80
122
8.8
224
7.9
201
92
42
2-1/2
65
12.8
325
4.80
122
8.8
224
7.9
201
92
42
3
80
12.8
325
4.80
122
8.8
224
7.9
201
92
42
4
100
12.8
325
4.80
122
8.8
224
7.9
201
92
42
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B23
Edward Valves
AA
B
Standard Features
UNWELD.
36125
36129
36225
36229
AA - Hub Diameter
B - Center to End
E - Center to Top (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
* Impactor Handle
B24
ENDS
NPS (DN)
Angle
Angle
Socket Welding
Buttwelding
Dimensions - Angle
Figure No. 36125, 36129,
36225, 36229
TYPE
NPS
DN
1/2
15
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
3/4
20
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
1
25
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
1-1/4
32
3.8
97
3.6
91
14.9
378
14.3*
363
40
18.1
42
19.1
1-1/2
40
3.8
97
3.6
91
14.9
378
14.3*
363
40
18.1
42
19.1
2
50
3.6
91
4.1
104
17.3
439
14.3*
363
60
27.2
62
28.1
2-1/2
65
4.0
102
4.5
114
19.1
485
16.0**
406
103
46.7
107
48.5
3
80
4.0
102
4.5
114
19.1
485
16.0**
406
103
46.7
107
48.5
4
100
4.8
122
5.3
135
19.7
500
16.0**
406
139
63.0
143
64.9
**Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A
AA
B
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or Welded Bonnet.
OS&Y.
Angle Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Integral Backseat.
Asbestos free graphitic packing.
UNWELD.
36165
36169
36265
36269
AA - Hub Diameter
B - Center to End
E - Center to Top (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
* Impactor Handle
TYPE
ENDS
NPS (DN)
Angle
Angle
Socket Welding
Buttwelding
Dimensions - Angle
Figure No. 36165, 36169,
36265, 36269
NPS
DN
1/2
15
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
3/4
20
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
1
25
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
1-1/4
32
3.8
97
3.6
91
14.9
378
14.3*
363
40
18.1
42
19.1
1-1/2
40
3.8
97
3.6
91
14.9
378
14.3*
363
40
18.1
42
19.1
2
50
3.6
91
4.1
104
17.3
439
14.3*
363
60
27.2
62
28.1
2-1/2
65
4.0
102
4.5
114
19.1
485
16.0**
406
103
46.7
107
48.5
3
80
4.0
102
4.5
114
19.1
485
16.0**
406
103
46.7
107
48.5
4
100
4.8
122
5.3
135
19.7
500
16.0**
406
139
63.0
143
64.9
**Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B25
Edward Valves
E
AA
B
B
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or Welded Cover.
Angle Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Stainless steel spring.
(Optional without spring, see page G14.)
UNWELD.
36175
36179
36275
36279
TYPE
ENDS
NPS (DN)
Angle
Angle
Socket Welding
Buttwelding
Dimensions - Angle
Figure No. 36175, 36179,
36275, 36279
AA - Hub Diameter
B - Center to End
E - Center to Top
Weight
B26
NPS
DN
1/2
15
2.3
58
2.5
64
4.6
117
8
3.6
3/4
20
2.3
58
2.5
64
4.6
117
8
3.6
1
25
2.3
58
2.5
64
4.6
117
8
3.6
1-1/4
32
3.8
97
3.6
91
5.7
145
21
9.5
1-1/2
40
3.8
97
3.6
91
5.7
145
21
9.5
2
50
3.6
91
4.1
104
6.2
157
30
13.6
2-1/2
65
4.0
102
4.5
114
7.2
183
41
18.6
3
80
4.0
102
4.5
114
7.2
183
41
18.6
4
100
4.8
122
5.3
135
7.8
198
76
34.5
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A
AA
B
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or Welded Bonnet.
OS&Y.
Angle Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Integral Backseat.
Asbestos free graphitic packing.
UNWELD.
66125
66129
66225
66229
AA - Hub Diameter
B - Center to End
E - Center to Top (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
* Impactor Handle
ENDS
NPS (DN)
Angle
Angle
Socket Welding
Buttwelding
Dimensions - Angle
Figure No. 66125, 66129,
66225, 66229
TYPE
NPS
DN
1/2
15
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
3/4
20
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
1
25
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
1-1/4
32
3.8
97
3.6
91
14.9
378
11.0*
279
38
17.2
40
18.1
1-1/2
40
3.8
97
3.6
91
14.9
378
11.0*
279
38
17.2
40
18.1
2
50
4.0
102
4.5
114
18.2
462
14.3*
363
76
34.5
80
36.3
2-1/2
65
4.8
122
5.3
135
19.7
500
16.0**
406
139
63.0
143
64.9
3
80
4.8
122
5.3
135
19.7
500
16.0**
406
139
63.0
143
64.9
4
100
4.8
122
5.3
135
19.7
500
16.0**
406
139
63.0
143
64.9
**Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
B27
Edward Valves
AA
B
B
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal)or Welded Bonnet.
OS&Y.
Angle Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Integral Backseat.
Asbestos free graphitic packing.
UNWELD.
66165
66169
66265
66269
AA - Hub Diameter
B - Center to End
E - Center to Top (Open)
G - Handwheel/Handle Diameter
Weight, Welded
Weight, Unwelded
* Impactor Handle
B28
ENDS
NPS (DN)
Angle
Angle
Socket Welding
Buttwelding
Dimensions - Angle
Figure No. 66165, 66169,
66265, 66269
TYPE
NPS
DN
1/2
15
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
3/4
20
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
1
25
2.3
58
2.5
64
11.7
297
8.5
216
18
8.2
19
8.6
1-1/4
32
3.8
97
3.6
91
14.9
378
11.0*
279
38
17.2
40
18.1
1-1/2
40
3.8
97
3.6
91
14.9
378
11.0*
279
38
17.2
40
18.1
2
50
4.0
102
4.5
114
18.2
462
14.3*
363
76
34.5
80
36.3
2-1/2
65
4.8
122
5.3
135
19.7
500
16.0**
406
139
63.0
143
64.9
3
80
4.8
122
5.3
135
19.7
500
16.0**
406
139
63.0
143
64.9
4
100
4.8
122
5.3
135
19.7
500
16.0**
406
139
63.0
143
64.9
**Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
E
AA
B
A
B
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316, F347 stainless steel.
Other material on application.
Unwelded (graphitic seal) or Welded Cover.
Angle Pattern.
Body-guided investment cast Stellite disk.
Integral Stellite seat.
Stainless steel spring.
(Optional without spring, see page G14.)
UNWELD.
66175
66179
66275
66279
AA - Hub Diameter
B - Center to End
E - Center to Top
Weight
ENDS
NPS (DN)
Angle
Angle
Socket Welding
Buttwelding
Dimensions - Angle
Figure No. 66175, 66179,
66275, 66279
TYPE
NPS
DN
1/2
15
2.3
58
2.5
64
4.6
117
8
3.6
3/4
20
2.3
58
2.5
64
4.6
117
8
3.6
1
25
2.3
58
2.5
64
4.6
117
8
3.6
1-1/4
32
3.8
97
3.6
91
5.7
145
23
10.4
1-1/2
40
3.8
97
3.6
91
5.7
145
23
10.4
2
50
4.0
102
4.5
114
7.2
183
46
20.9
2-1/2
65
4.8
122
5.3
135
7.8
198
76
34.5
3
80
4.8
122
5.3
135
7.8
198
76
34.5
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
4
100
4.8
122
5.3
135
7.8
198
76
34.5
B29
Edward Valves
EV100
5th Edition
Edward Valves
11. Disk piston is body guided to eliminate misalignment, galling and stem bending.
7. Yoke bushing material has low coefficient of friction which substantially reduces torque and thread
wear and eliminates galling.
8. Stem has ACME threads, is machined to a fine finish and is heat treated for improved strength and
hardness to resist wear.
14. Body utilizes optimized flow passages to minimize flow direction changes and reduce pressure
drop.
C2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Body/Bonnet*
Disk
Body-Guided Disk Nut
Stem
Yoke Bushing
ASTM NO.
A-216
Grade WCB
A-105
A-216
Grade WCB
A-182
Grade F6a
B-148
Alloy 95400
Packing Rings
Junk Rings
AISI 1117
Cad. Plated
ASTM NO.
ASTM NO.
ASTM NO.
A-217
A-217
A-217
Grade WC6
Grade WC9
Grade C12A
A-182
A-182
A-182
Grade F11
Grade F22
Grade F91
A-217
A-217
A-217
Grade WC6
Grade WC9
Grade C12A
A-182
A-565
A-565
Grade F6a
Grade 616 HT
Grade 616 HT
B-148
B-148
B-148
Alloy 95400
Alloy 95400
Alloy 95400
Flexible Graphite inner rings and suitable anti-extrusion rings.
AISI 1117
AISI 1117
AISI 1117
Cad. Plated
Cad. Plated
Cad. Plated
Composite Pressure Seal Gasket.
A-668 Grade 4140
A-668 Grade 4140
A-668 Grade 4140
Cad. Plated
Cad. Plated
Cad. Plated
A-182
A-565
A-565
Grade F6 CL4
Grade 616 HT
Grade 616 HT
A-216
A-216
A-216
Grade WCB
Grade WCB
Grade WCB
A-193
A-193
A-193
Grade B7
Grade B7
Grade B7
A-194
A-194
A-194
Grade 2H
Grade 2H
Grade 2H
A-148
A-148
A-148
Grade 90-60
Grade 90-60
Grade 90-60
A-193
A-193
A-193
Grade B7/Cad. Plated
Grade B7/Cad. Plated
Grade B7/Cad. Plated
A-194
A-194
A-194
Grade 2/Cad. Plated
Grade 2/Cad. Plated
Grade 2/Cad. Plated
A-182
A-182
A-182
Grade F6a
Grade F6a
Grade F6a
Class 4
Class 4
Class 4
A-515
A-515
A-515
Grade 70
Grade 70
Grade 70
A-331
A-331
A-331
Grade 4140 HT
Grade 4140 HT
Grade 4140 HT
A-216
A-216
A-216
Grade WCB
Grade WCB
Grade WCB
A-216
A-216
A-216
Grade WCB
Grade WCB
Grade WCB
A-193
A-193
A-193
Grade B7
Grade B7
Grade B7
A-194
A-194
A-194
Grade 2H
Grade 2H
Grade 2H
A-126
A-126
A-126
Class A
Class A
Class A
A-536
A-536
A-536
Grade 65-45-12
Grade 65-45-12
Grade 65-45-12
A-536
A-536
A-536
Grade 65-45-12
Grade 65-45-12
Grade 65-45-12
A-182
A-565
A-565
Grade F6a
Grade 616 HT
Grade 616 HT
ASTM NO.
A-351
Grade CF8M
A-182
Grade F316
A-182
Grade F316
A-638
Grade 660 T2
B-148
Alloy 95400
A-182
Grade F316/Stellite I.D.
A-182
Grade F6 CL4
A-638
Grade 660 T2
A-216
Grade WCB
A-193
Grade B7
A-194
Grade 2H
A-148
Grade 90-60/Chrome Plated
A-193
Grade B7/Cad. Plated
A-194
Grade 2/Cad. Plated
A-182
Grade F6a
Class 4
A-515
Grade 70
A-331
Grade 4140 HT
A-216
Grade WCB
A-216
Grade WCB
A-193
Grade B7
A-194
Grade 2H
A-126
Class A
A-536
Grade 65-45-12
A-536
Grade 65-45-12
A-638
Grade 660 T2
(1) Through Class 2500, for Series 4500 valves, some construction differences exist. Contact your Edward Valves sales representative for more information.
*
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C3
Edward Valves
Flite-Flow
Angle
Globe
Equalizer
All Edward cast steel stop-check valves are equipped with an Equalizer pipe. Acting as an
external pressure balancing pipeline, the Equalizer connects the zone above the disk with
the lower pressure area in the valve outlet (see drawing above). This reduces pressure
above the disk, and as a result, causes the higher pressure below the disk to raise the disk
to full lift. The Equalizer helps reduce pressure drop and disk-piston movement and wear.
Elbow Down
All other features are the same as those defined on page C-2 for stop valves.
C4
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Flite-Flow
Angle
Globe
Elbow Down
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C5
Edward Valves
C6
5. Springs insure quick closing of the disk by providing a positive seating force to speed closing.
6. Hinge pin provides a disk pivot point close to its
center of gravity for fast response to flow reversals
which minimizes water hammer effects.
7. Hinge pin gasket is spiral wound, coated steel, or
flexible graphite for long reliable service.
8. Body features a straight thru compact design for low
pressure drop.
9. Disk assembly is dome shaped and counterweighted for fast response to flow reversals.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Disk
ASTM NO.
ASTM NO.
Gasket Retainer
Cover Retainer
Cover Retainer
ASTM NO.
ASTM NO.
A-216
A-217
A-217
A-217
A-351
Grade WCB
Grade WC6
Grade WC9
Grade C12A
Grade CF8M
A-105
A-182
A-182
A-182
A-182
Grade F11
Grade F22
Grade F91
Grade F316
ASTM NO.
Grade 182
Cad. Plated
Cad. Plated
Cad. Plated
Cad. Plated
Grade F6 CL4
A-182
A-182
A-565
A-565
A-638
Grade F6 CL4
Grade F6 CL4
Grade 616 HT
Grade 616 HT
Grade 660 T2
A-216
A-216
A-216
A-216
A-216
Grade WCB
Grade WCB
Grade WCB
Grade WCB
Grade WCB
A-193
A-193
A-193
A-193
A-193
Capscrews or Studs
Grade B7
Grade B7
Grade B7
Grade B7
Grade B7
A-194
A-194
A-194
A-194
A-194
Grade 2H
Grade 2H
Grade 2H
Grade 2H
Grade 2H
Spiral Wound
Spiral Wound
Spiral Wound
Spiral Wound
Spiral Wound
Gasket
Gasket
Gasket
Gasket
Gasket
(Asb. Free)
(Asb. Free)
(Asb. Free)
(Asb. Free)
(Asb. Free)
Graphite Gasket
A-182
A-182
A-565
A-565
A-638
Grade F6aCL4
Grade F6aCL4
Grade 616 HT
Grade 616 HT
A-193
A-193
A-193
A-453
A-453
Grade B7
Grade B16
Grade B16
Grade 660B
Grade 660B
A-105
A-182
A-182
A-182
A-182
Grade F11
Grade F22
Grade F91
Grade F316
A-313
A-313
A-313
A-313
A-313
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C7
Edward Valves
C8
12. Stem - has ACME threads, is machined to a fine finish and is heat treated for
improved strength and hardness to resist wear.
13. Packing gland - made of alloy steel, and retained against the stuffing box
pressure by an easy-to-maintain stud and heavy hex nut assembly.
14. Bonnet retaining ring - assures an effective, tight seal by pulling the bonnet
and gasket together at the pressure seal.
15. Yoke lock ring - permits easier field maintenance of upper structure without
disturbing pressure containing parts. Valves in smaller sizes utilize a wishbone
yoke design. Class 600 valves utilize a bolted pressure seal bonnet.
16. Bonnet backseat - especially hard faced to assure long-term sealability.
17. Hemispherical-type bonnet - reduces valve body height and provides weight
savings. Hemispherical-type design results in better pressure distribution across
the bonnet area.
18. Two-piece wedge assembly - allows each wedge half to flex and adjust independently to compensate for body distortions caused by thermal changes or pipe
bending stresses. (see pg. C-10)
19. Welded-in seat ring with hardfaced seat - assures better wear and longer
valve life. Seat ring is welded into the valve body to prevent leakage.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
DESCRIPTION(1)
Body/Bonnet*
Gate 2-1/2-6
Gate 8 and up*
Stem
Yoke Bushing
ASTM NO.
Gasket Retainer
Bonnet Retainer
Bonnet Retainer Studs
Bonnet Retainer Nuts
Gland
Gland Studs
Gland Nuts
Yoke
Yoke Lock Ring
Yoke Lock Ring Studs
Yoke Lock Ring Nuts
Handwheel
ASTM NO.
ASTM NO.
A-216
A-217
A-217
A-217
A-351
Grade WC6
Grade WC9
Grade C12A
Grade CF8M
A-743
A-743
A-743
A-732
A-732
Grade 21
Grade 21
A-216
A-217
A-217
A-217
A-351
Grade WCB
Grade WC6
Grade WC9
Grade C12A
Grade CF8M
A-182
A-182
A-565
A-565
A-638
Grade F6 CL4
Grade F6 CL4
Grade 616 HT
Grade 616 HT
Grade 660 T2
B-148
B-148
B-148
B-148
B-148
Alloy 95400
Alloy 95400
Alloy 95400
Alloy 95400
Alloy 95400
AISI 1117
AISI 1117
AISI 1117
AISI 1117
A-182
Cad. Plated
Cad. Plated
Cad. Plated
Cad. Plated
ASTM NO.
Grade WCB
Packing Rings
Junk Rings
ASTM NO.
A-182
Cad. Plated
Cad. Plated
Cad. Plated
Cad. Plated
Grade F6 CL4
A-182
A-182
A-565
A-565
A-638
Grade F6 CL4
Grade F6 CL4
Grade 616 HT
Grade 616 HT
Grade 660 T2
A-515
A-515
A-515
A-515
A-515
Grade 70
Grade 70
Grade 70
Grade 70
Grade 70
A-193
A-193
A-193
A-193
A-193
Grade B7
Grade B7
Grade B7
Grade B7
Grade B7
A-194
A-194
A-194
A-194
A-194
Grade 2H
Grade 2H
Grade 2H
Grade 2H
Grade 2H
A-148
A-148
A-148
A-148
A-148
Grade 90-60
Grade 90-60
Grade 90-60
Grade 90-60
A-193
A-193
A-193
A-193
A-193
A-194
A-194
A-194
A-194
A-194
A-216
A-216
A-216
A-216
A-216
Grade WCB
Grade WCB
Grade WCB
Grade WCB
Grade WCB
A-216
A-216
A-216
A-216
A-216
Grade WCB
Grade WCB
Grade WCB
Grade WCB
Grade WCB
A-193
A-193
A-193
A-193
A-193
Grade B7
Grade B7
Grade B7
Grade B7
Grade B7
A-194
A-194
A-194
A-194
A-194
Grade 2H
Grade 2H
Grade 2H
Grade 2H
Grade 2H
A-126
A-126
A-126
A-126
A-126
Class A
Class A
Class A
Class A
Class A
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C9
Edward Valves
Guiding System
Body Grooves
Wedge Halves
Body
Groove
Body
Body
Hardfaced
Wedge Seat
Hardfaced
Wedge Guide Rails
Welded-in
Seat Ring
Figure 1
Figure 2
Wedge Half
Captured Stem
Stem Seating
Shoulder
Non-revolving
Stem
Wedge Half
Spacer Ring
Stem
Backseat
Wedge Half
Figure 3
Figure 4
C10
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
NPS
DN
2-1/2
65
5.75
146
13.6
345
11
279
ENDS
Flanged
Buttwelding
Flanged
Buttwelding
Threaded
Socket Welding
NPS (DN)
3 (80)thru
12 (300)
2-1/2 (65)
thru 12 (300)
2-1/2 (65)
TYPE
Globe
Globe
Angle
Angle
Angle
Angle
65
29
55
25
3
80
12.5
318
6.25
159
16.2
411
14.4
366
11.5
292
100
45
80
36
94
43
70
32
4
100
14
356
7
178
16.7
424
14.6
371
11.5
292
193
88
95
43
126
57
85
39
5
125
15.76
400
7.88
200
20.1
510
17.7
450
15
381
226
103
172
78
210
95
152
69
6
150
17.5
445
8.75
222
24.8
630
21.4
544
18
457
370
168
295
134
300
136
225
102
8
200
22
559
11
279
28.4
721
24.2
615
22
559
525
238
400
181
425
193
325
147
10
250
24.5
622
12.25
310
34.3
871
28.8
731
22
559
895
406
720
327
710
322
530
240
12
300
28
711
14
356
39.7
1008
32.9
836
26
660
1520
689
1270
576
1250
561
970
440
* Regular handwheel standard on all sizes except size 12 has an impactor handwheel and size 2-1/2 has an impactor handle.
Center to end or end to end dimensions for welding end valves same as center to contact face or contact face to contact face dimensions for flanged
end valves.
# Long Terne Steel is a product coated by immersion in molten terne metal.
Terne Metal is an alloy of lead and a small amount (about 3%) of tin.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C11
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel (WCB, WC6).
Bolted or OS & Y.
Y-Pattern.
Integral Stellite seat, disk and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Gasket:
Size 2-1/2 6 asbestos free, spiral wound.
All others Long Terne# steel.
ENDS
Flanged
Buttwelding
NPS (DN)
2-1/2 (65)
thru 16 (400)
* Size 3&4 Buttweld Valves are Class 400. See page C17.
1324
1324Y
Flite-Flow
Flite-Flow
Threaded
Socket Welding
2-1/2 (65)
Dimensions - Flite-Flow
Figure No. 1314/1314Y
1324/1324Y
TYPE
Flite-Flow
Flite-Flow
NPS
DN
2 1/2
65
3
80
4
100
6
150
8
200
10
250
12
300
14
350
16
400
11.5
292
11.5
292
16
406
11
279
56
25
70
32
13
330
16
406
17.2
437
11.5
292
100
45
130
59
15.5
394
20.25
514
22
559
15
381
150
68
200
91
20
508
23.75
603
29
737
22
559
300
136
380
173
26.5
673
29
737
35
889
22
559
575
261
700
318
31
787
34.75
883
41
1041
26
660
1030
468
1200
545
40
1016
43
1092
47.8
1213
30
762
1500
682
1750
795
40
1016
43.25
1099
47.8
1213
30
762
1525
693
1850
841
42
1067
44
1118
47.8
1213
30
762
1575
716
1950
886
Long Terne Steel is a product coated by immersion in molten terne metal. Terne Metal is an alloy of lead and a
small amount (about 3%) of tin.
**Impactor handwheel standard on 10" and larger Flite-Flow Valves. Impactor handle standard on 2-1/2 valve.
C12
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
304
Standard Features
NPS
DN
2-1/2
65
5.75
146
13.6
345
11
279
5.9
150
TYPE
Globe
Globe
Angle
Angle
ENDS
Flanged
Buttwelding
Flanged
Buttwelding
NPS (DN)
3 (80) thru
12 (300)
2-1/2 (65) thru
12 (300)
66
29
51
23
3
80
12.5
318
6.25
159
16.2
411
14.4
366
11.5
292
8.7
221
100
45
75
34
100
45
70
32
4
100
14
356
7
178
16.7
424
14.6
371
11.5
292
8.5
216
110
50
95
43
130
59
90
41
5
125
15.76
400
7.88
200
20.1
510
17.7
450
15
381
10
254
230
104
175
79
200
91
152
69
6
150
17.5
445
8.75
222
24.8
630
21.4
544
18
457
9.6
244
370
168
295
134
300
136
215
98
8
250
22
559
11
279
28.4
721
24.2
615
22
559
11
279
525
238
400
181
450
204
325
147
10
250
24.5
622
12.25
310
34.3
871
28.8
731
22
559
13.7
348
920
417
765
327
700
318
560
254
12
300
28
711
14
356
39.7
1008
32.9
836
26
660
15
381
1525
692
1365
619
1250
567
970
440
* Regular handwheel standard on all sizes except size 12 has an impactor handwheel and size 2-1/2 has an impactor handle.
Center to end or end to end dimensions for welding end valves same as center to contact face or contact face to contact face dimensions for
flanged end valves.
# Long Terne Steel is a product coated by immersion in molten terne metal.
Terne Metal is an alloy of lead and a small amount (about 3%) of tin.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C13
Edward Valves
Standard Features
ENDS
Flanged
Buttwelding
NPS (DN)
2-1/2 (65) thru
16 (400)
* Size 3&4 Buttweld Valves are Class 400. See page C18.
Dimensions - Flite-Flow
Figure No. 1302/1302Y
TYPE
Flite-Flow
Flite-Flow
NPS
DN
2-1/2
65
11.5
292
11.5
292
16
406
11
279
56
25
70
32
3
80
13
330
16
406
17.2
437
11.5
292
100
45
130
59
4
100
15.5
394
20.25
514
22
559
15
381
150
68
200
91
6
150
20
508
23.75
603
29
737
22
559
300
136
380
173
8
200
26.5
673
29
737
35
889
22
559
575
261
700
318
10
250
31
787
34.75
885
41
1041
26
660
1030
468
1200
545
12
300
40
1016
43
1092
47.8
1213
30
762
1500
682
1750
795
14
350
40
1016
43.25
1099
47.8
1213
30
762
1525
693
1850
841
16
400
42
1067
44
1118
47.8
1213
30
762
1575
716
1950
886
Long Terne Steel is a product coated by immersion in molten terne metal. Terne Metal is an alloy of lead and a small amount
(about 3%) of tin.
** Impactor handwheel standard on 10 NPS & larger Flite-Flow Valves. 2-1/2 NPS has impactor handle.
#
C14
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
394
Standard Features
NPS
DN
2-1/2
65
5.75
146
3.88
99
5.9
150
ENDS
Threaded
Socket Welding
Flanged
Buttwelding
Flanged
Buttwelding
NPS (DN)
2-1/2 (65)
3 (80) thru
12 (300)
2-1/2 (65) thru
12 (300)
TYPE
Angle
Angle
Globe
Globe
Angle
Angle
49
22
35
16
3
80
12.5
318
6.25
159
6.58
167
4.82
122
8.7
221
85
39
60
27
78
35
53
24
4
100
14
356
7
178
7.08
180
4.96
126
8.5
216
120
54
85
39
108
49
70
32
5
125
15.76
400
7.88
200
8.88
226
6.44
164
10
254
195
88
141
64
175
79
121
55
6
150
17.5
445
8.75
222
11.4
290
8.04
204
9.6
244
320
145
250
113
250
113
260
118
8
200
22
559
11
279
13.1
333
8.9
226
11
279
470
213
350
159
375
170
250
113
10
250
24.5
622
12.25
310
15.9
405
10.5
267
13.7
348
835
379
620
281
600
272
430
195
12
300
28
711
14
356
18.5
470
11.7
297
15
381
1280
581
1050
476
980
445
820
372
Center to end or end to end dimensions for welding end valves same as center to contact face to contact face dimensions for flanged end valves.
Long Terne Steel is a product coated by immersion in molten terne metal. Terne Metal is an alloy of lead and a small amount (about 3%) of tin.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C15
Edward Valves
Check Valves
Standard Features
ENDS
Flanged
Buttwelding
NPS (DN)
2-1/2 (65)
16 (400)
* Size 3&4 Buttweld Valves are Class 400. See page C18.
1390
1390Y
Flite-Flow
Flite-Flow
Threaded
Socket Welding
2-1/2 (65)
Dimensions - Flite-Flow
Figure No. 1392/1392Y
TYPE
Flite-Flow
Flite-Flow
NPS
DN
2-1/2
65
11.5
292
11.5
292
7
178
40
18
54
25
3
80
13
330
16
406
8
203
70
32
100
45
4
100
15.5
394
20.25
514
11
279
105
48
150
68
6
150
20
508
23.75
603
13.5
343
210
95
290
132
8
200
26.5
673
29
737
17
432
400
182
520
236
10
250
31
787
34.75
883
20
508
700
318
875
398
12
300
40
1016
43
1092
25.5
648
1050
477
1300
591
14
350
40
1016
43.25
1099
25.5
648
1075
489
1400
636
16
400
42
1067
44
1118
25.5
648
1125
511
1500
682
Long Terne Steel is a product coated by immersion in molten terne metal. Terne Metal is an alloy of lead and a small amount (about 3%) of tin.
C16
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
TYPE
ENDS
1314Y
Flite-Flow
Buttwelding
NPS (DN)
3 (80)
thru 4 (100)
Dimensions - Flite-Flow
Figure No. 1314Y
A1- End to End (Welding)
E - Center to Top (Open)
G - Handwheel Diameter
Weight (Welding)
#
NPS
DN
3
80
14
356
16
406
11.5
292
100
45
4
100
15.5
394
22
559
16
406
150
68
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C17
Edward Valves
Standard Features
TYPE
ENDS
1302Y
Flite-Flow
Buttwelding
NPS (DN)
3 (80)
thru 4 (100)
Dimensions - Flite-Flow
Figure No. 1302Y
A - End to End (Welding)
E - Center to Top (Open)
G - Handwheel Diameter
H - Equalizer Clearance
Weight (Welding)
#
C18
NPS
DN
3
80
14
356
16
406
11.5
292
8.0
203
100
45
4
100
15.5
394
22
559
16
406
9.5
241
150
68
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
Standard Features
TYPE
ENDS
1392Y
Flite-Flow
Buttwelding
NPS (DN)
3 (80)
thru 4 (100)
Dimensions - Flite-Flow
Figure No. 1392Y
A - End to End (Welding)
E - Center to Top/Check Valve
H - Equalizer Clearance
Weight (Welding)
#
NPS
DN
3
80
14
356
8
203
8.0
203
70
32
4
100
15.5
394
11
279
9.5
241
105
48
Long Terne Steel is a product coated by immersion in molten terne metal. Terne Metal
is an alloy of lead and a small amount (about 3%) of tin.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C19
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A).
Bolted or pressure-seal bonnet, OS & Y.
Globe or angle.
Integral Stellite seat, disk and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Long Terne# steel or composite
pressure-seal gasket.
SPL CL
616
616Y
617
617Y
618
618Y
619
619Y
716Y
717Y
TYPE
ENDS
BONNET
NPS (DN)
Globe
Globe
Angle
Angle
Globe
Globe
Angle
Angle
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding
NPS
DN
2-1/2
65
13
330
6.5
165
16.2
411
14.4
366
12
305
110
50
90
41
100
45
100
45
3
80
14
356
7
178
16.7
424
14.6
371
12
305
135
61
110
50
122
55
125
57
4
100
17
432
8.5
216
20.1
511
17.7
450
14
356
245
111
180
82
228
103
170
77
5
125
20
508
10
254
24.8
630
21.4
544
16
406
425
193
315
143
355
161
245
111
6
150
22
559
11
279
28.4
721
24.2
615
16
406
525
238
400
181
460
209
350
159
8
200
26
660
13
330
34.3
871
28.8
731
20
508
900
408
750
340
730
331
540
245
10
250
31
787
15.5
394
39.7
1008
32.9
836
26
660
1550
703
1200
544
1230
558
950
431
12
300
33
838
16.5
419
43.6
1107
36.1
917
30
762
2200
998
1850
839
1790
812
1450
658
14
350
35
889
17.5
445
47
1194
38.8
986
30
762
2640
1198
2250
1021
2120
962
1760
798
* Angle valves only, are also available in Sizes 24, 28, and 30. Dimensions available upon request.
** Impactor handwheel is standard on all size valves.
Center to end or end to end dimensions for welding and valves same as center to contact face or contact face to contact face dimensions for flanged
end valves.
C20
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A).
Pressure-seal bonnet, OS & Y.
Y-Pattern.
Integral Stellite seat, disk and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphite packing.
Spiral wound or composite
pressure-seal gasket.
C
Pressure Class 600 (PN 110)*
FIG. NO.
STD CL
614***
614Y
SPL CL
714Y
TYPE
ENDS
BONNET
NPS (DN)
Flite-Flow
Flite-Flow
Flanged
Buttwelding
*Pressure Seal
*Pressure Seal
3 (80)
thru 32 (800)
Dimensions - Flite-Flow
Figure No. 614Y/714Y
614***
NPS
DN
3
4
80
100
13
15.5
330
394
16.75 21.25
425
540
17.5 21.5
445
546
12
14
305
356
110
150
50
68
150
240
68
109
6
150
20
508
29
737
28.5
724
16
406
450
204
570
259
8
200
26
660
33
838
34
864
20
508
850
385
1000
454
10
12
14
250
300 250
31
38
38
788
965 965
39
43
43
991 1092 1092
42
49
49
1067 1245 1245
26
30
30
660
762 762
1400 2050 2050
635
930 930
1800 2450 2550
816 1111 1157
16
400
41
1041
52
1321
74
1880
48
1219
5500
2495
6500
2948
20
500
60
1524
*
71
1803
48
1219
9200
4173
*
24
26
600 650
66
70
1676 1778
28
32
700 800
81.5
90
2070 2286
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C21
Edward Valves
Stop Valves
Standard Features
SPL CL
1611*
1611Y
1711Y
1611BY
1711BY
A1611
A1611Y
TYPE
ENDS
BONNET
NPS (DN)
Equiwedge Gate
Equiwedge Gate
Venturi Pattern
Equiwedge Gate
Equiwedge Gate
Equiwedge Gate
Flanged
Buttwelding
Pressure-Seal
Pressure-Seal
Buttwelding
Pressure-Seal
Flanged
Buttwelding
Bolted
NPS
DN
2-1/2
65
10
254
13
330
22.25
565
14
356
81
37
22.5
572
130
59
3
80
10
254
14
356
22.25
565
14
356
81
37
22.5
572
130
59
4
100
12
305
17
432
25.5
648
14
356
175
79
24
610
175
79
6
150
18
457
22
559
31.75
806
24
610
372
169
27.38
695
390
177
8
200
23
584
26
660
39.75
1010
24
610
667
303
10
250
28
711
31
787
48
1219
30
762
1050
476
12
300
32
813
33
838
54
1372
30
762
1623
738
14
350
35
889
35
889
58.5
1486
36
914
2345
1066
C22
NPS
DN
16
400
39
991
39
991
67
1702
36
914
2950
1338
18
450
43
1092
43
1092
76
1930
36
914
3600
1633
20
500
47
1194
47
1194
82.75
2102
36
914
5000
2268
22
550
51
1295
51
1295
89
2261
48
1219
5700
2585
24
600
55
1397
55
1397
96
2438
48
1219
6500
2948
26
650
57
1448
57
1448
101
2565
48
1219
8000
3628
28
700
61
1549
61
1549
110.5
2807
48
1219
10,000
4535
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
C
Bold face numerals are in inches and pounds.
Blue numerals are in millimeters and kilograms.
NPS
DN
8x6x8
200
18
457
31.75
806
24
610
372
169
10x8x10
250
23
584
39.75
1010
24
610
610
277
12x10x12
300
28
711
48
1219
30
762
1114
506
14x12x14
350
32
813
54
1372
30
762
1623
738
NPS
DN
20x18x20
500
43
1092
76
1930
36
914
3600
1633
22x20x22
550
47
1194
82.75
2102
36
914
5000
2268
18x16x18
450
39
991
67
1702
36
914
2950
1338
16x14x16
400
35
889
58.5
1486
36
914
2345
1066
24x20x24
600
47
1194
82.75
2102
48
1219
5700
2585
26x22x26
650
51
1295
89
2261
48
1219
6500
2948
28x24x28
700
55
1397
96
2438
48
1219
7000
3175
30x26x30
750
57
1448
101
2565
48
1219
8500
3855
32x28x32
800
61
1549
110.5
2807
48
1219
10,500
4762
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C23
Edward Valves
SPL CL
604
604Y
605
605Y
606
606Y
607
607Y
706Y
707Y
TYPE
ENDS
BONNET
Globe
Globe
Angle
Angle
Globe
Globe
Angle
Angle
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding
Bolted
Bolted
Bolted
Bolted
Pressure-Seal
Pressure-Seal
Pressure-Seal
Pressure-Seal
NPS
DN
NPS (DN)
2-1/2
65
13
330
6.5
165
16.2
411
14.4
366
12
305
8.7
221
110
50
84
38
105
48
80
36
3
80
14
356
7
178
16.7
424
14.6
371
12
305
8.5
216
135
61
110
50
125
57
90
41
4
100
17
432
8.5
216
20.1
511
17.7
450
14
356
10
254
220
112
185
84
225
102
168
76
5
125
20
508
10
254
24.8
630
21.4
544
16
406
9.6
244
425
193
335
152
325
147
245
111
6
150
22
559
11
279
28.4
721
24.2
615
16
406
11
279
540
245
410
186
460
209
350
159
8
200
26
660
13
330
34.3
871
28.8
731
20
508
11.8
300
960
435
750
340
750
340
560
254
10
250
31
787
15.5
394
39.7
1008
32.9
836
26
660
13
330
1540
699
1270
596
1200
544
950
431
12
300
33
838
16.5
419
43.6
1107
36.1
917
30
762
13.7
348
2200
998
1850
839
1790
812
1450
667
14
350
35
889
17.5
445
47
1194
38.8
986
30
762
15.7
399
2680
1216
2250
1021
2150
975
1760
798
* Angle valves only, are also available in Sizes 24, 28, and 30. Dimensions available upon request.
** Center to end or end to end dimensions for welding and valves same as center to contact face or contact face to contact face dimensions for flanged end valves.
# Impactor handwheel is standard on all size valves.
C24
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A).
Bolted or pressure-seal
bonnet, OS & Y.
Y-Pattern.
Integral Stellite seat, disk
and backseat.
Body-guided disk piston.
13% chromium stainless
steel stem.
Asbestos free graphitic packing.
Spiral wound or composite
pressure seal gasket.
Equipped with equalizer.
SPL CL
***602
602Y
702Y
TYPE
ENDS
BONNET
NPS (DN)
Flite-Flow
Flite-Flow
Flanged
Buttwelding
Pressure-Seal*
Pressure-Seal*
3 (80) thru
32 (800)
* Size 3&4 - Bolted bonnet with asbestos free spiral wound gasket.
* Size 3&4 Buttweld Valves are Class 700. See page C28.
Dimensions - Flite-Flow
Figure No. 602Y/702Y
***602
A1 - End to End, (Welding)
A2 - Face to Face, (Flanged)
E - Center to Top, (Open)
G - Handwheel Diameter
H - Equalizer Clearance
Weight, (Welding)
Weight, (Flanged)
NPS
DN
3
80
13
330
16.75
425
17.5
445
12
305
7
178
110
50
150
68
4
100
15.5
394
21.25
540
21.5
546
14
356
9
229
150
68
240
109
6
150
20
508
29
737
28.5
724
16
406
10
254
450
204
570
259
8
200
26
660
33
838
34
864
20
508
12
305
850
385
1000
454
10
250
31
787
39
991
42
1067
26
660
13
330
1400
635
1800
816
12
300
38
965
43
1092
49
1245
30
762
14
356
2050
930
2850
1293
14
250
38
965
43
1092
49
1245
30
762
14
356
2050
930
3100
1406
16
400
41
1041
52
1321
74
1880
48
1219
22
559
5500
2495
6500
2948
20
500
60
1524
24
600
66
1676
26
650
70
1778
28
700
81.5
2070
32
800
90
2286
71
1803
48
1219
24
610
9200
4173
*
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C25
Edward Valves
Check Valves
Standard Features
Bodies and covers are
cast steel (WCB, WC6,
WC9, C12A).
Bolted or pressure-seal
cover.
Y-Pattern, globe, angle,
or tilting disk.
Integral Stellite seats.
Body-guided disk
piston, globe, angle &
Flite-Flow.
Long Terne# steel or
pressure-seal gasket.
Equipped with equalizer,
globe, angle &
Flite-Flow.
SPL CL
670Y
690
690Y
691
691Y
***692
692Y
694
694Y
695
695Y
770Y
792Y
794Y
795Y
TYPE
ENDS
BONNET
NPS (DN)
Tilting Disk
Globe
Globe
Angle
Angle
Flite-Flow
Flite-Flow
Globe
Globe
Angle
Angle
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding
Bolted
Bolted
Bolted
Bolted
Bolted
*Pressure Seal
*Pressure Seal
Pressure Seal
Pressure Seal
Pressure Seal
Pressure Seal
3 (80) thru
32 (800)
8 (200) thru 14 (350)
* Size 3&4 - Bolted bonnet with asbestos free spiral wound gasket.
* Size 3&4 Buttweld Flite-Flow Valves are Class 700. See page C29.
NPS
DN
2-1/2
65
13
330
6.5
165
6.6
168
4.8
122
8.7
221
80
36
60
27
72
33
50
23
3
80
14
356
7
178
7.1
180
5.0
127
8.5
216
110
50
80
36
95
43
70
32
4
100
17
432
8.5
216
8.9
226
6.4
163
10
254
210
95
140
64
184
84
124
56
5
125
20
508
10
254
11.4
290
8.0
203
9.6
244
360
163
250
113
290
132
180
82
6
150
22
559
11
279
13.1
333
8.9
226
11
279
460
209
325
147
380
172
250
113
8
200
26
660
13
330
17.3
439
11.9
302
11.8
300
815
370
620
281
590
268
400
181
10
250
31
787
15.5
394
20.2
513
13.4
340
13
330
1290
585
1040
472
990
449
710
322
12
300
33
838
16.5
419
23.2
589
15.5
394
13.7
348
1870
848
1550
703
1490
676
1170
531
14
350
35
889
17.5
445
25.1
638
16.6
422
15.7
399
2320
1052
1930
875
1830
830
1440
653
Center to end or end to end dimensions for welding end valves same as center to contact face or contact face to contact face dimensions for flanged end valves.
Long Terne Steel is a product coated by immersion in molten terne metal. Terne Metal is an alloy of lead and a small amount (about 3%) of tin.
***Flanged valves available in sizes 3 to 16.
#
C26
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
692Y
Standard Features
Bodies and covers are cast steel (WCB, WC6, WC9, C12A).
Bolted or pressure-seal cover.
Y-Pattern, globe, angle, or tilting disk.
Integral Stellite seats.
Body-guided disk piston, globe, angle & Flite-Flow.
Gasket: Sizes 3 & 4 asbestos free, spiral wound.
All others: composite pressure seal.
Equipped with equalizer, globe, angle & Flite-Flow.
C
Bold face numerals are in inches and pounds.
Blue numerals are in millimeters and kilograms.
Dimensions - Flite-Flow
Figure No.692Y/792Y
***692
NPS
DN
3
80
13
330
16.75
425
7
178
7
178
80
35
120
54
4
100
15.5
394
21.5
540
11
279
9
229
125
55
200
90
6
150
20
508
29
737
15.75
400
10
254
375
170
520
236
8
200
26
660
33
838
17.75
451
12
305
575
261
750
340
10
250
31
787
39
991
21.25
540
13
330
1000
454
1250
567
12
300
38
965
43
1092
25.25
641
14
356
1450
658
1900
862
14
250
38
965
43
1321
25.25
641
14
356
1450
658
2150
975
16
400
41
1041
52
1321
31.5
800
22
559
3300
1497
4300
1950
20
500
60
1524
*
*
36.0
914
24
610
*
24
600
66
1676
*
*
*
26
650
70
1778
*
*
*
28
700
81.5
2070
*
32
800
90
2286
*
*
*
*
*
*
*
*
*
*
*
*
*
*
E, H and other dimensions and information supplied upon request.
*** Flanged valves available in sizes 3 thru 16.
Note: Size 3&4 Buttweld Class 600 Flite-Flow valves are Class 700. See page C30.
NPS
DN
6
150
19.5
495
9.5
241
15.25
387
300
136
8
200
22
559
10.5
267
17.5
445
500
225
10
250
28.5
724
13.5
343
21
533
950
428
12
300
34.5
876
15.5
394
25
635
1450
653
14
350
34.5
876
15.5
394
25
635
1550
698
16
400
43.25
1099
20.5
521
32.25
819
2550
1148
18
450
48.25
1226
22.5
572
34
864
3550
1598
20
500
53.5
1359
23.75
603
38.5
978
5650
2543
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C27
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A).
Bolted bonnet, OS & Y.
Y-Pattern.
Integral Stellite seat, disk and
backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Asbestos free spiral wound gasket.
614Y
SPL CL
714Y
TYPE
ENDS
BONNET
NPS (DN)
Flite-Flow
Buttwelding
Bolted
Dimensions - Flite-Flow
Figure No.614Y**
714Y**
A - End to End (Welding)
E - Center to Top, (Open)
G - Handwheel Diameter
Weight (Welding)
NPS
DN
3
80
14
356
16
406
11
279
110
50
4
100
15.5
394
21.5
546
14
356
150
68
C28
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A).
Bolted bonnet, OS & Y.
Y-Pattern.
Integral Stellite seat, disk
and backseat.
Body-guided disk piston.
13% chromium stainless
steel stem.
Asbestos free graphitic
packing.
Asbestos free spiral wound gasket.
Equipped with equalizer.
C
Pressure Class 700 (PN 120)
FIG. NO.
STD CL
602Y
SPL CL
702Y
TYPE
ENDS
BONNET
NPS (DN)
Flite-Flow
Buttwelding
Bolted
Dimensions - Flite-Flow
Figure No.602Y/702Y
A - End to End (Welding)
E - Center to Top, (Open)
G - Handwheel Diameter**
H - Equalizer Clearance
Weight (Welding)
NPS
DN
3
80
14
356
16
406
11
279
7
178
110
50
4
100
15.5
394
21.5
546
14
356
9
229
150
68
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C29
Edward Valves
Check Valves
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9, C12A).
Bolted cover.
Y-Pattern.
Integral Stellite seat and disk.
Body-guided disk piston.
Asbestos free spiral wound gasket.
Equipped with equalizer.
SPL CL
692Y
792Y
TYPE
ENDS
BONNET
NPS (DN)
Flite-Flow
Buttwelding
Bolted
Dimensions - Flite-Flow
Figure No.692Y/792Y
A - End to End (Welding)
E - Center to Top
H - Equalizer Clearance
Weight (Welding)
C30
NPS
DN
3
80
14
356
8
203
7
178
80
35
4
100
15.5
394
11
279
9
229
125
55
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel (WCB, WC6,
WC9, C12A, CF8M, or CF8C).
Pressure-seal Bonnet, OS & Y.
Y-Pattern, globe & angle design.
Integral Stellite seat, disk and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Yoke bushing thrust bearings size 5 and larger.
SPL CL
4016
4016Y
4017
4017Y
4014
4014Y
4316Y
4317Y
ENDS
NPS (DN)
Globe
Globe
Angle
Angle
Flite-Flow
Flite-Flow
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding*
3 (80)
thru 14 (350)
3 (80)
thru 24 (600)
3 (80)
thru 16 (400)
* Size 3&4 Buttweld Flite-Flow Valves are Class 1100 - see page C40.
4314Y
TYPE
NPS
DN
3
80
15
381
7.5
190
15
381
7.5
190
22.5
572
20.4
518
16
406
210
95
175
79
206
93
150
68
4
100
18
457
9
229
18
457
9
229
26.25
667
23.75
603
16
406
310
141
235
107
284
129
210
95
5
125
22
559
11
279
22
559
11
279
30.6
777
28.25
718
20
508
610
277
500
227
540
245
410
185
6
150
24
610
12
305
24
610
12
305
37
940
34.25
870
20
508
800
363
620
281
710
322
552
250
8
200
29
737
14.5
368
29
737
14.5
368
46
1168
43.4
1102
28
711
1570
712
1390
630
1360
612
1035
466
10
250
33
838
16.5
419
33
838
16.5
419
54.75
1391
49.25
1251
28
711
2410
1093
2300
1043
2103
946
1690
761
12
300
38
965
19
483
38
965
19
483
64.75
1645
60
1524
36
914
3700
1665
3100
1395
3010
1365
2555
1159
14
350
40.5
1029
19
483
40.5
1029
21.75
552
71.25
1810
60
1524
36
914
4600
2086
3850
1746
3060
1388
2580
1170
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C31
Edward Valves
Stop Valves
Dimensions - Angle
16
400
26
660
78.5
1994
48
1219
4440
2014
18
450
**
**
**
**
20
500
32.5
825
95
2413
72
1829
8150
3697
24
600
39
991
102
2591
72
1829
13,750
6237
Dimensions - Flite-Flow
Figure No. 4014/4014Y, 4314Y
A1 - End to End, (Welding)
A2 - Face to Face, (Flanged)
E - Center to Top, (Open)
G - Handwheel Diameter*
Weight, (Welding)
Weight, (Flanged)
NPS
DN
3
80
17
432
22.25
565
20
508
16
406
190
86
250
113
4
100
18.5
479
23.75
603
25
635
16
406
275
125
370
168
6
150
20
508
30
762
35
889
20
508
550
249
775
352
8
200
26
660
38
965
44
1118
28
711
1150
522
1550
703
10
250
31
787
44
1118
51
1295
28
711
2100
953
2650
1202
12
300
38
965
50
1270
60
1524
36
914
3400
1542
4150
1882
14
350
38
965
51
1295
60
1524
36
914
3400
1542
4550
2064
16
400
44.5
1130
58
1473
73
1854
48
1219
5550
2517
6950
3152
C32
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel (WCB, WC6, WC9, C12A, CF8M or CF8C).
Bolted or pressure-seal bonnet, OS & Y.
Integral Stellite seat, disk and backseat.
Two-piece body-guided wedge.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Available in standard or venturi pattern.
Yoke bushing thrust bearings.
Long Terne# steel or composite pressure seal gasket.
SPL CL
1911
1911Y
14311Y
1911BY
14311BY
A1911
A1911Y
TYPE
ENDS
BONNET
NPS (DN)
Equiwedge Gate
Equiwedge Gate
Venturi Pattern
Equiwedge Gate
Equiwedge Gate
Equiwedge Gate
Flanged*
Buttwelding
Pressure-Seal
Pressure-Seal
Buttwelding
Pressure-Seal
Flanged
Buttwelding
Bolted
2-1/2 (65)
thru 28 (700)
8 (200)
thru 32 (800)
2-1/2 (65)
thru 4 (100)
NPS
DN
2-1/2
65
12
305
16.5
419
21.25
540
14
356
95
43
22.5
572
130
59
NPS
DN
4
100
14
356
18
457
24.5
622
18
457
165
75
24
610
190
86
6
150
20
508
24
610
33.5
851
24
610
380
172
8
200
26
660
29
737
40
1016
24
610
690
313
10
250
31
787
33
838
46.75
1187
36
914
1523
692
12
300
36
914
38
965
54.5
1384
36
914
2118
963
14
350
39
991
40.5
1029
59
1499
36
914
2805
1275
3
80
12
305
15
381
21.25
540
14
356
125
57
22.5
572
130
59
16
400
43
1092
44.5
1130
68
1727
36
914
4150
1882
18
450
48
1291
48
1291
73.75
1873
36
914
4300
1950
20
500
52
1321
52
1321
82
2083
48
1219
5800
2631
22
550
57
1448
57
1448
89.25
2267
48
1219
7500
3402
24
600
61
1549
61
1549
95
2413
48
1219
9600
4355
26
28
650
700
64
68
1626
1727
Available
Upon Request
102
109
2591
2769
60
60
1524
1524
12,000
5443
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C33
Edward Valves
Stop Valves
NPS
DN
8x6x8
200
20
508
33.5
851
24
610
530
241
10x8x10
250
26
660
40
1016
24
610
891
405
C34
NPS
DN
20x18x20
500
48
1219
73.75
1873
36
914
4500
2041
22x20x22
550
52
1321
82
2083
48
1219
6970
3162
14x12x14
350
36
914
54.5
1384
36
914
2118
963
16x14x16
400
39
991
59
1499
36
914
2805
1275
18x16x18
450
43
1092
68
1727
36
914
4150
1882
26x22x26
650
57
1448
89.25
2267
48
1219
8000
3629
28x24x28
700
61
1549
95
2413
48
1219
10,000
4536
30x26x30
750
64
1626
102
2591
60
1524
12,500
5670
32x28x32
800
68
1727
109
2769
60
1524
15,000
6804
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Standard Features
Bodies and bonnets are cast steel (WCB,
WC6, WC9, C12A, CF8M or CF8C).
Pressure-seal Bonnet, OS & Y.
Y-Pattern, globe & angle design.
Integral Stellite seat, disk and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Equipped with equalizer.
Yoke bushing thrust bearings.
SPL CL
4006
4006Y
4007
4007Y
4002
4002Y
4306Y
4307Y
4302Y
NPS
DN
ENDS
NPS (DN)
Globe
Globe
Angle
Angle
Flite-Flow
Flite-Flow
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding*
3 (80)
thru 14 (350)
3 (80)
thru 24 (600)
3 (80)
thru 16 (400)
* Size 3&4 Buttweld Flite-Flow Valves are Class 1100 - see page C41.
TYPE
3
80
15
381
7.5
190
15
381
7.5
190
22.5
572
20.38
518
16
406
7.5
190
220
100
175
79
206
93
150
68
4
100
18
457
9
22
18
457
9
229
26.25
667
23.75
603
16
406
7.63
194
314
142
245
111
284
129
215
98
5
125
22
559
11
279
22
559
11
279
30.63
778
28.25
718
20
508
9.75
248
615
279
500
227
540
245
410
186
6
150
24
610
12
305
24
610
12
305
37
940
34.25
870
20
508
10.75
273
800
363
642
291
690
313
552
250
8
200
29
737
14.5
368
29
737
14.5
368
46
1168
43.38
1102
28
711
12.5
318
1570
712
1400
635
1360
617
1035
469
10
250
33
838
16.5
419
33
838
16.5
419
54.75
1391
49.25
1251
28
711
12.88
327
2425
1100
2300
1043
2103
954
1600
725
12
300
38
965
19
483
38
965
19
483
64.75
1645
60
1524
36
914
14.75
375
3700
1665
3100
1406
3010
1365
2555
1159
14
350
40.5
1029
19
483
40.5
1029
21.75
552
71.25
1810
62.75
1594
36
914
17.38
441
4600
2087
4750
2155
3060
1388
2580
1170
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C35
Edward Valves
Dimensions - Angle
NPS
DN
16
400
26
660
78.5
1994
48
1219
20
50.8
4960
2250
18
450
**
**
**
**
**
20
500
32.5
825
95
2413
72
1829
21.5
546
8150
3697
24
600
39
991
102
2591
72
1829
30
762
13,750
6237
Dimensions - Flite-Flow
Figure No. 4002/4002Y, 4302Y
A1 - End to End (Welding)
A2 - Face to Face (Flanged)
E - Center to Top (Open)
G - Handwheel Diameter*
H - Equalizer Clearance
Weight (Welding)
Weight (Flanged)
NPS
DN
3
80
17
432
22.25
565
20
508
16
406
9
229
190
86
250
113
4
100
18.5
470
23.75
603
25
635
16
406
9.3
236
275
125
370
168
6
150
20
508
30
762
35
889
20
508
10
254
555
252
775
352
8
200
26
660
38
965
44
1118
28
711
12.5
318
1150
522
1550
703
10
250
31
787
44
1118
51
1295
28
711
16
406
2100
953
2650
1202
12
300
38
965
50
1270
60
1524
36
914
15
381
3400
1542
4150
1882
14
350
38
965
51
1295
60
1524
36
914
15
381
3400
1542
4550
2064
16
400
44.5
1130
58
1473
73
1854
48
1219
25.75
654
5550
2517
6950
3153
C36
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
Standard Features
Bodies and Covers are cast steel (WCB, WC6,
WC9, C12A, CF8M or CF8C).
Pressure-seal Cover.
Globe, angle & tilting disk design.
Integral Stellite seats.
Body-guided disk piston. (Globe & Angle)
Equipped with equalizer. (Globe & Angle)
TYPE
ENDS
4370Y
Tilting Disk
Buttwelding
4394Y
4395Y
4392Y
Globe
Globe
Angle
Angle
Flite-Flow
Flite-Flow
Flanged
Buttwelding
Flanged
Buttwelding
Flanged
Buttwelding*
STD CL
SPL CL
970Y
4094
4094Y
4095
4095Y
4092
4092Y
*Size 3&4 Buttweld Flite-Flow Valves are Class 1100 - see page C42.
NPS (DN)
NPS
DN
3
80
15
381
7.5
190
15
381
7.5
190
11
279
9.25
235
7.5
190
140
64
108
49
134
61
115
52
4
100
18
457
9
229
18
457
9
229
12
305
10.25
260
7.63
194
246
112
160
73
217
98
131
59
5
125
22
559
11
279
22
559
11
279
13.75
349
11.25
286
9.75
248
426
193
272
123
356
161
202
92
6
150
24
610
12
305
24
610
12
305
15.63
397
12.5
318
10.75
273
550
249
400
181
485
220
290
132
8
200
29
737
14.5
368
29
737
14.5
368
18.5
470
16
406
12.5
318
1188
539
840
381
898
407
510
231
10
250
33
838
16.5
419
33
838
16.5
419
22.25
565
16.75
425
12.88
327
1310
594
1090
494
1080
490
860
390
12
300
38
965
19
483
38
965
19
483
26.25
667
21.5
546
14.75
275
2710
1229
2110
957
2165
982
1565
710
14
350
40.5
1029
20.25
514
40.5
1029
20.25
514
28.75
730
21.5
546
17.38
441
3820
1733
3070
1393
2345
1064
1860
844
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C37
Edward Valves
Check Valves
Dimensions - Angle
Figure No. 4095/4095Y, 4395Y
NPS
DN
16
400
26
660
29
737
20
508
2675
1213
18
450
29
737
32
813
21
533
3710
1682
20
500
32.5
825
32
813
21.5
546
4930
2636
24
600
39
991
36
914
30
762
8190
3714
2-1/2*
65
12
305
7.25
184
10.5
267
95
43
3*
80
12
305
7.25
184
10.5
267
95
43
4*
100
12
305
7.25
184
10.5
267
120
54
6
150
22
559
9.25
235
16.5
419
535
243
8
200
28
711
11
279
16
406
600
272
10
250
34
864
13
330
20.5
521
1010
458
16
400
47
1194
18.75
476
29
737
3260
1479
18
450
53
1346
18.75
476
29
737
3300
1497
20
500
51.5
1308
23
584
37.5
953
4510
2046
24
600
78
1981
36
914
55
1397
10,200
4627
NPS
DN
*Spiral wound hinge pin gaskets; hinge pin torsion spring not required.
C38
NPS
DN
12
300
42
1067
15.75
400
26.5
673
2090
948
14
350
40.5
1029
15.75
400
26.5
673
2090
948
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9, C12A, CF8M or CF8C).
Pressure-seal cover.
Y-Pattern.
Integral Stellite seats.
Body-guided disk piston.
Equipped with equalizer.
Dimensions - Flite-Flow
Figure No. 4092/4092Y, 4392Y
A1 - End to End (Welding)
A2 - Face to Face (Flanged)
E - Center to Top
H - Equalizer Clearance
Weight, (Welding)
Weight, (Flanged)
NPS
DN
3
80
17
432
22.25
565
10
254
9
229
130
59
190
86
4
100
18.5
470
23.75
603
11
279
9.3
236
175
79
250
113
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C39
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, CF8M, or CF8C).
Pressure-seal bonnet, OS & Y.
Y-Pattern.
Integral Stellite seat, disk and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
SPL CL
4014Y
4314Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 4014Y, 4314Y
A - End to End, (Welding)
E - Center to Top, (Open)
G - Handwheel Diameter*
Weight, (Welding)
NPS
DN
3
80
17
432
20
508
16
406
190
86
4
100
18.5
470
25
635
16
406
275
125
C40
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Standard Features
Bodies and bonnets are cast steel (WCB,
WC6, WC9, C12A, CF8M, or CF8C).
Pressure-seal bonnet, OS & Y.
Y-Pattern.
Integral Stellite seat, disk
and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Equipped with equalizer.
C
Pressure Class 1100 (PN 190)
FIG. NO.
STD CL
SPL CL
4002Y
4302Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 4002Y, 4302Y
A - End to End (Welding)
E - Center to Top (Open)
G - Handwheel Diameter*
H - Equalizer Clearance
Weight (Welding)
NPS
DN
3
80
17
432
20
508
16
406
9
229
190
86
4
100
18.5
470
25
635
16
406
10
254
275
125
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C41
Edward Valves
Check Valves
Standard Features
Bodies and covers are cast steel (WCB,
WC6, WC9, C12A, CF8M, or CF8C).
Pressure-seal cover.
Y-Pattern.
Integral Stellite seat and disk.
Body-guided disk piston.
Equipped with equalizer.
SPL CL
4092Y
4392Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 4092Y, 4392Y
A - End to End (Welding)
E - Center to Top
H - Equalizer Clearance
Weight (Welding)
C42
NPS
DN
3
80
17
432
10
254
9
229
130
59
4
100
18.5
470
11
279
10
254
175
79
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel (WCB, WC6,
WC9, C12A, CF8M or CF8C).
Pressure-seal bonnet, OS & Y.
Y-Pattern, globe & angle design.
Integral Stellite seats and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Yoke bushing thrust bearings size 5 and larger.
TYPE
ENDS
2014Y
Flite-Flow
Buttwelding*
2016Y
2017Y
Globe
Globe
Angle
Angle
Flanged
Buttwelding
Flanged
Buttwelding
STD CL
SPL CL
7514Y
7516
7516Y
7517
7517Y
3 (80) thru
24 (600)
2-1/2 (65)
thru 14 (350)
2-1/2 (65)
thru 24 (600)
*Size 3&4 Buttweld Flite-Flow Valves are Class 1800 - see page C53.
NPS (DN)
NPS
DN
2-1/2
65
13
330
6.5
165
16.5
419
8.25
210
19.25
489
18
457
14
356
167
76
90
41
153
69
80
36
3
80
15
381
7.5
190
18.5
470
9.25
235
22.5
572
20.4
518
16
406
260
118
175
79
230
104
150
68
4
100
18
457
9
229
21.5
546
10.75
273
26.25
667
23.75
603
16
406
385
175
270
122
330
150
255
116
5
125
22
559
11
279
26.5
673
13.25
337
30.63
778
28.25
718
20
508
760
345
525
238
730
331
510
231
6
150
24
610
12
305
27.75
705
13.88
353
36.5
927
34.75
883
20
508
960
435
700
317
865
392
670
304
8
200
29
737
14.5
368
32.75
832
16.38
416
48.75
1238
45.75
1162
28
711
1800
816
1620
735
1580
717
1250
567
10
250
33
838
16.5
419
39
991
19.5
495
59.5
1511
56
1422
36
914
3150
1429
2600
1179
2780
1261
2200
998
12
300
38
965
19
483
44.5
1130
22.25
565
70
1778
66.3
1684
36
914
4910
2227
3710
1683
4100
1860
2900
1315
14
350
40.5
1029
20.25
514
49.5
1257
24.75
629
70
1778
66.75
1695
48
1219
5900
2676
4850
2200
4850
2200
3800
1724
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C43
Edward Valves
16
400
23.5
597
77.5
1969
48
1219
6600
2994
18
450
23.5
597
77.5
1969
48
1219
6800
3084
20
500
28.5
724
84
2134
72
1829
9500
4309
24
600
35.5
902
103
2616
72
1829
16,200
7348
Dimensions - Flite-Flow
Figure No. 7514Y/2014Y
NPS
DN
3
80
4
100
6
150
8
200
10
250
12
300
14
350
16
400
18
450
20
500
24
600
17
432
18.5
470
27.75
705
30
762
36.25
921
43
1092
41
1041
54
1372
63
1600
54.5
1384
59.5
1511
20
508
25
635
34.25 45
870 1143
53.5
1359
60.75
1543
60.75
1543
78.5
1994
78.5
1994
96
2438
96
2438
G - Handwheel Diameter*
16
406
16
406
20
508
28
711
36
914
36
914
36
914
48
1219
48
1219
72
1829
72
1829
Weight (Welding)
210
95
300
136
700
318
1550
702
2725
1236
4220
1914
4300
1950
7650
3470
8390
3806
10,500
4763
16,800
7620
C44
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel (WCB,
WC6, WC9,C12A, CF8M or CF8C).
Pressure-seal bonnet, OS & Y.
Integral Stellite seats and backseat.
Two piece body-guided wedge.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Available in standard or venturi pattern.
Yoke bushing thrust bearings.
TYPE
ENDS
NPS (DN)
Equiwedge Gate
Equiwedge Gate
Venturi Pattern
Equiwedge Gate
Flanged*
Buttwelding
SPL CL
11511
11511Y 12011Y
11511BY 12011BY
Buttwelding
NPS
DN
NPS
DN
2-1/2
65
12
305
16.5
419
21.25
540
14
356
125
57
3
80
12
305
18.5
470
21.25
540
14
356
125
57
4
100
16
406
21.5
546
24.25
616
18
457
190
86
6
150
22
559
27.75
705
31.5
800
24
610
490
222
8
200
28
711
32.75
832
40
1016
36
914
675
306
10
250
34
864
39
991
48.25
1226
36
914
1730
785
12
300
39
991
44.5
1130
55.25
1403
36
914
2725
1236
16
400
47
1194
54.5
1384
68.75
1746
48
1219
4450
2019
18
450
53
1346
60.5
1537
73.75
1873
48
1219
6000
2722
20
500
58
1473
65.5
1664
80
2032
60
1524
8000
3629
22
550
67
1702
71
1803
86.75
2203
60
1524
10,500
4763
24
600
76.5
1943
76.5
1943
93.5
2375
60
1524
13,000
5897
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C45
Edward Valves
Stop Valves
NPS
DN
8x6x8
200
22
559
31.5
800
24
610
490
222
10x8x10
250
28
711
40
1016
36
914
1082
491
C46
NPS
DN
20x18x20
500
53
1346
73.75
1873
48
1219
6200
2812
14x12x14
350
39
991
55.25
1403
36
914
2725
1236
16x14x16
400
42
1067
61
1549
48
1219
3600
1633
18x16x18
450
47
1194
68.75
1746
48
1219
4600
2087
22x20x22
550
58
1473
80
2032
60
1524
8200
3720
24x20x24
600
58
1473
80
2032
60
1524
8,500
3855
26x22x26
650
67
1702
86.75
2203
60
1524
11,000
4990
28x24x28
700
76.5
1943
93.5
2375
60
1524
13,500
6124
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Standard Features
Bodies and bonnets are cast steel (WCB, WC6,
WC9, C12A, CF8M or CF8C).
Pressure-seal bonnet, OS & Y.
Y-Pattern, globe or angle design.
Integral Stellite seats and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Equipped with equalizer.
Yoke bushing thrust bearings size 5 and larger.
TYPE
ENDS
2002Y
Flite-Flow
Buttwelding*
2006Y
2007Y
Globe
Globe
Angle
Angle
Flanged
Buttwelding
Flanged
Buttwelding
STD CL
SPL CL
7502Y
7506
7506Y
7507
7507Y
3 (80) thru
24 (600)
2-1/2 (65) thru
14 (350)
2-1/2 (65) thru
24 (600)
*Size 3&4 Buttweld Flite-Flow Valves are Class 1800. See page C54.
NPS (DN)
NPS
DN
2-1/2
65
13
330
6.5
165
16.5
419
8.25
210
19.25
489
18
457
14
356
6.75
171
167
76
90
41
153
69
77
35
3
80
15
381
7.5
190
18.5
470
9.25
235
22.5
572
20.38
518
16
406
7.75
197
270
122
180
82
230
104
160
73
4
100
18
457
9
229
21.5
546
10.75
273
26.25
667
23.75
603
16
406
7.75
197
385
175
270
122
330
149
255
116
5
125
22
559
11
279
26.5
673
13.25
337
30.63
778
28.25
718
20
508
10
254
770
349
570
258
730
331
510
231
6
150
24
610
12
305
27.75
705
13.88
353
36.5
927
34.75
883
20
508
10.75
273
960
435
710
322
865
392
585
265
8
200
29
737
14.5
368
32.75
832
16.38
416
48.75
1238
45.75
1162
28
711
12.75
324
1800
816
1470
667
1580
717
1250
567
10
250
33
838
16.5
419
39
991
19.5
495
59.5
1511
56
1422
36
914
14
356
3150
1429
2600
1179
2780
1261
2200
998
12
300
38
965
19
483
44.5
1130
22.25
565
70
1778
66.3
1684
36
914
15
381
4910
2227
3710
1683
4100
1860
2900
1315
14
350
40.5
1029
20.25
514
49.5
1257
24.75
628
70
1778
66.75
1695
48
1219
17.38
441
5900
2676
4850
2200
4850
2200
3800
1724
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C47
Edward Valves
Dimensions - Angle
NPS
DN
18
450
23.5
597
77.5
1969
48
1219
19.5
495
6800
3084
20
500
28.5
724
84
2134
72
1829
23
584
9500
4309
24
600
35.5
902
103
2616
72
1829
28.5
724
16,200
7348
Dimensions - Flite-Flow
Figure No. 7502Y, 2002Y
16
400
23.5
597
77.5
1969
48
1219
19.5
495
6600
2994
3
80
17
432
20
508
16
406
9
229
210
95
4
100
18.5
470
25
635
16
406
10
254
300
136
6
150
27.75
705
34.25
870
20
508
10.75
273
720
327
8
200
30
762
45
1143
28
711
12.75
324
1600
726
10
250
36.25
921
53.5
1359
36
914
15.75
400
2820
1279
12
300
43
1092
60.75
1543
36
914
16.5
419
4260
1932
14
350
41
1041
60.75
1543
36
914
16.5
419
4280
1941
16
400
54
1372
78.5
1994
48
1219
19.5
495
8450
3833
18
450
63
1600
78.5
1994
48
1219
19.5
495
8400
3810
20
500
54.5
1384
96
2438
72
1829
28
711
10,500
4763
24
600
59.5
1511
96
2438
72
1829
28
711
11,500
5216
C48
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
Standard Features
Pressure Class 1500 (PN 260)*
FIG. NO.
STD CL
SPL CL
7594
7594Y
7595
7595Y
7592Y
2094Y
2095Y
2092Y
ENDS
NPS (DN)
Globe
Globe
Angle
Angle
Flite-Flow
Flanged
Buttwelding
Flanged
Buttwelding
Buttwelding*
*Size 3&4 Buttweld Flite-Flow Valves are Class 1800. See page C55.
TYPE
NPS
DN
2-1/2
65
13
330
6.5
165
16.5
419
8.25
210
9.25
235
8.25
210
6.75
171
125
57
65
29
107
49
57
26
3
80
15
381
7.5
190
18.5
470
9.25
235
11
279
9.25
235
7.75
197
195
88
115
52
186
84
94
43
4
100
18
457
9
229
21.5
546
10.75
273
12
305
10.25
260
7.75
197
320
145
180
82
290
132
152
69
5
125
22
559
11
279
26.5
673
13.25
337
13.75
349
11.25
286
10
254
534
242
308
140
350
159
260
118
6
150
24
610
12
305
27.75
705
13.88
353
15
381
13
330
10.75
273
684
310
470
213
470
213
340
154
8
200
29
737
14.5
368
32.75
832
16.38
416
18.75
476
15.75
400
12.75
324
1390
631
960
435
1070
485
680
308
10
250
33
838
16.5
419
39
991
19.5
495
20.75
527
17.25
438
14
356
2360
1070
1530
694
1060
481
1230
558
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C49
Edward Valves
Check Valves
C50
NPS
DN
12
300
38
965
19
483
44.5
1130
22.25
565
24.25
616
20.5
521
15
381
3100
1406
2310
1040
2320
1044
1530
686
14
350
40.5
1029
20.25
514
49.5
1257
24.75
629
30
762
25
635
17.38
441
4400
1995
3300
1497
3900
1769
2060
927
16
400
18
450
20
500
24
600
23.5
597
28.5
724
35.5
902
24.5
622
19.5
495
42
1067
23
584
51
1295
28.5
724
4880
2213
6820
3093
11,600
5261
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
C
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9, C12A, CF8M or
CF8C).
Pressure-seal cover.
Y-Pattern.
Integral Stellite seats.
Body-guided disk piston.
Equipped with equalizer.
Dimensions - Flite-Flow
Figure No. 2092Y, 7592Y
A - End to End
E - Center to Top
H - Equalizer Clearance
Weight
NPS
DN
3
80
17
432
10
254
9
229
140
64
4
100
18.5
470
11
279
10
254
200
91
6
150
27.75
705
16
406
10.75
273
480
218
8
200
30
762
20.75
527
12.75
324
900
408
10
250
36.25
921
25.5
648
15.75
400
1750
794
12
300
43
1092
29.25
743
16.5
419
2525
1145
14
350
41
1041
29.25
743
16.5
419
2525
1145
16
400
54
1372
34
864
19.5
495
5550
2517
18
450
63
1600
34
864
19.5
495
5850
2654
20
500
54.5
1384
43
1092
28
711
6700
3039
24
600
58
1478
43
1092
28
711
11,200
5080
Note: Size 3&4 Buttweld Class 1500 Flite-Flow Valves are Class 1800. See page C55.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C51
Edward Valves
Check Valves
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9, C12A, CF8M or CF8C).
Pressure-seal cover.
Y-Pattern.
Integral Stellite seats.
Body-guided disk piston.
SPL CL
1570Y
2070Y
ENDS
NPS (DN)
Tilting Disk
Buttwelding
TYPE
NPS
DN
2-1/2*
65
12
305
7.25
184
10.5
267
90
41
3*
80
12
305
7.25
184
10.5
267
90
41
4*
100
12
305
7.25
184
10.5
267
95
43
6
150
22
559
9.25
235
16.5
419
460
209
8
200
28
711
11
279
16.75
425
600
272
10
250
34
864
13
330
20.5
521
1005
456
* Spiral wound hinge pin gaskets; hinge pin torsion spring not required.
C52
NPS
DN
12
300
42
1067
15.75
400
26.5
673
1520
689
14
350
40.5
1029
15.75
400
26.5
673
1550
703
16
400
47
1194
18.75
476
29
737
3280
1487
18
450
53
1346
18.75
476
29
737
3590
1628
20
500
51.5
1308
23
584
37.5
953
4600
2087
24
600
58
1473
36
914
55
1397
10,300
4672
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A,
CF8M or CF8C).
Pressure-seal cover, OS & Y.
Y-Pattern.
Integral Stellite seats.
Body-guided disk piston.
13% chromium stainless
steel stem.
SPL CL
7514Y
2014Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 7514Y, 2014Y
A - End to End
E - Center to Top (Open)
G - Handwheel Diameter*
Weight (Welding)
NPS
DN
3
80
17
432
20
508
16
406
210
95
4
100
18.5
470
25
635
16
406
300
136
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C53
Edward Valves
7502Y
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A,
CF8M or CF8C).
Pressure-seal bonnet, OS&Y.
Y-Pattern.
Integral Stellite seats.
Body-guided disk piston.
Equipped with equalizer.
13% chromium stainless
steel stem.
Asbestos free graphitic packing.
SPL CL
7502Y
2002Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 7502Y, 2002Y
A - End to End
E - Center to Top (Open)
G - Handwheel Diameter*
H - Equalizer Clearance
Weight (Welding)
C54
NPS
DN
3
80
17
432
20
508
16
406
9
229
210
95
4
100
18.5
470
25
635
16
406
10
254
300
136
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9, C12A, CF8M,
or CF8C).
Pressure-seal cover.
Y-Pattern.
Integral Stellite seat and disk.
Body-guided disk piston.
Equipped with equalizer.
SPL CL
7592Y
2092Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 7592Y, 2092Y
A - End to End
E - Center to Top (Open)
H - Equalizer Clearance
Weight (Welding)
NPS
DN
3
80
17
432
10
254
9
229
140
64
4
100
18.5
470
11
279
10
254
200
91
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C55
Edward Valves
Stop Valves
2214Y
2214Y
Standard Features
Bodies and bonnets are cast
steel (WCB, WC6, WC9, C12A,
CF8M or CF8C).
Pressure-seal cover, OS & Y.
Y-Pattern.
Integral Stellite seat, disk and
backseat.
Body-guided disk piston.
13% chromium stainless
steel stem.
Asbestos free graphitic packing.
SPL CL
2214Y
3214Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 2214Y, 3214Y
A - End to End
E - Center to Top (Open)
G - Handwheel Diameter*
Weight (Welding)
C56
NPS
DN
12
300
39
991
58
1473
48
1219
4300
1950
14
350
39
991
58
1473
48
1219
4300
1950
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
2202Y
2202Y
Standard Features
SPL CL
2202Y
3202Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 2202Y, 3202Y
A - End to End
E - Center to Top (Open)
G - Handwheel Diameter*
H - Equalizer Clearance
Weight
NPS
DN
12
300
39
991
58
1473
48
1219
18
457
4300
1950
14
350
39
991
58
1473
48
1219
18
457
4300
1950
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C57
Edward Valves
Check Valves
2292Y
2292Y
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9, C12A, CF8M,
or CF8C).
Pressure-seal cover.
Y-Pattern.
Integral Stellite seat and disk.
Body-guided disk piston.
Equipped with equalizer.
SPL CL
2292Y
3292Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 2292Y, 3292Y
A - End to End
E - Center to Top
H - Equalizer Clearance
Weight
C58
NPS
DN
12
300
39
991
24
610
18
457
2900
1315
14
350
39
991
24
610
18
457
2900
1315
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A, CF8M or
CF8C).
Pressure-seal bonnet, OS & Y.
Vertical, Y-Pattern & angle design.
Integral Stellite seat, disk and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Yoke bushing thrust bearings size 5
and larger.
TYPE
ENDS
4414Y
Flite-Flow
Buttwelding*
4416Y
4417Y
Globe
Globe
Angle
Angle
Flanged
Buttwelding
Flanged*
Buttwelding
STD CL
SPL CL
3914Y
3916
3916Y
3917
3917Y
3 (80) thru
24 (600)
2-1/2 (65) thru
12 (300)
2-1/2 (65) thru
24 (600)
NPS (DN)
NPS
DN
2-1/2
65
13
330
6.5
165
20
508
10
254
19.63
499
18
457
14
356
158
72
95
43
150
68
82
37
3
80
15
381
7.5
190
22.75
578
11.38
289
22.38
568
20
508
16
406
330
150
165
75
255
115
148
67
4
100
18
457
9
228
26.5
673
13.25
337
25.25
572
22.5
641
16
406
442
200
255
115
490
222
220
100
5
125
22
559
11
279
31.25
794
15.63
397
28.25
718
25
635
20
508
890
404
560
254
830
376
465
211
6
150
24
610
12
305
36
914
18
457
37.63
955
33.75
857
28
711
1586
719
900
408
1466
665
780
354
8
200
29
737
14.5
368
40.25
1022
20.13
511
47.25
1200
42.25
1073
28
711
2370
1075
1610
730
2120
961
1450
657
10
250
33
838
16.5
419
50
1270
25
635
55.25
1403
48.75
1238
36
914
3160
1433
2440
1107
3320
1505
2110
957
12
300
38
965
19
483
56
1422
28
711
72.5
1842
69.5
1765
48
1219
5050
2290
3400
1542
4650
2109
3000
1360
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C59
Edward Valves
Stop Valves
Dimensions - Angle
NPS
DN
14
350
20.25
514
67
1701
48
1219
5350
2427
16
400
20.25
514
67
1701
48
1219
5410
2454
18
450
23.5
597
92
2300
72
1829
10,460
4745
NPS
DN
22
550
26
660
89.5
2238
72
1829
14,350
6509
24
600
28.5
724
96
2438
72
1829
18,200
8255
Dimensions - Flite-Flow
Figure No. 3914Y, 4414Y
20
500
23.5
597
92
2300
72
1829
10,540
4781
3
80
17
432
20
508
16
406
230
104
4
100
18.5
470
25
635
16
406
325
147
6
150
24
610
37.5
953
28
711
875
397
8
200
30
762
41.75
1060
28
711
1610
730
10
250
36
914
50
1270
36
914
2750
1247
12
300
41
1041
65
1651
48
1219
4600
2087
14
350
48.75
1238
69
1753
48
1219
6990
3171
16
400
48.75
1238
69
1753
48
1219
7010
3180
18
20
24
450
500
600
58
58
68
1473
1473
1727
93.8
93.8
113
2382
2382
2870
72
72
72
1829
1829
1829
12,700 12,790 16,570
5761
5802
7516
C60
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A, CF8M
or CF8C).
Pressure-seal bonnet, OS & Y.
Integral Stellite seat and
backseat.
Two piece body-guided wedge.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Available in standard or venturi
pattern.
Yoke bushing thrust bearings.
TYPE
ENDS
NPS (DN)
Equiwedge Gate
Equiwedge Gate
Venturi Pattern
Equiwedge Gate
Flanged*
Buttwelding
2-1/2 (65)
thru 24 (600)
8 (200)
thru 28 (700)
SPL CL
12511
12511Y 14411Y
12511BY 14411BY
Buttwelding
NPS
DN
NPS
DN
2-1/2
65
13
330
20
508
21.5
546
24
610
126
57
3
80
14.5
368
22.75
578
21.5
546
24
610
126
57
4
100
18
457
26.5
673
22
559
24
610
318
144
G - Handwheel Diameter
Weight (Welding)
8
200
30
762
40.25
1022
36.75
933
36
914
1245
565
10
250
36
914
50
1270
49.25
1251
36
914
2130
966
12
300
41
1041
56
1422
56
1422
48
1219
3557
1613
16
400
49
1245
18
450
55
1397
6
150
24
610
36
914
31.75
806
30
762
715
324
20
500
62
1575
22
550
64
1626
24
600
66
1676
75.5
1918
60
1524
11,400
5171
87.25
2116
72
1829
13,000
5897
88.75
2254
72
1829
15,000
6804
N/A
56.75
1441
48
1219
5167
2349
66
1676
48
1219
6600
2994
71
1803
60
1524
8600
3901
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C61
Edward Valves
Stop Valves
NPS
DN
8x6x8
200
24
610
31.75
806
30
762
715
325
10x8x10
250
30
762
36.75
933
36
914
1245
566
C62
NPS
DN
18x16x18
450
49
1245
66
1676
48
1219
6600
2994
14x12x14
350
41
1041
56
1422
48
1219
3557
1617
16x14x16
400
44
1118
56.75
1441
48
1219
5167
2349
20x18x20
500
55
1397
71
1803
60
1524
8600
3901
22x20x22
550
62
1575
75.5
1918
60
1524
11,400
5171
24x20x24
600
62
1575
75.5
1918
60
1524
13,000
5900
26x22x26
650
64
1626
87.25
2116
72
1829
15,000
6800
28x24x28
700
66
1676
88.75
2254
72
1829
15,000
6800
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Standard Features
Bodies and bonnets are cast
steel (WCB, WC6, WC9, C12A,
CF8M or CF8C).
Pressure-seal bonnet, OS & Y.
Y-Pattern, globe & angle design.
Integral Stellite seat, disk and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Equipped with equalizer.
Yoke bushing thrust bearings size 5
and larger.
TYPE
ENDS
4402Y
Flite-Flow
Buttwelding*
4406Y
4407Y
Globe
Globe
Angle
Angle
Flanged
Buttwelding
Flanged*
Buttwelding
STD CL
SPL CL
3902Y
3906
3906Y
3907
3907Y
3 (80) thru
24 (600)
2-1/2 (65) thru
12 (300)
2-1/2 (65) thru
24 (600)
NPS (DN)
NPS
DN
2-1/2
65
13
330
6.5
165
20
508
10
254
19.63
499
18
457
14
356
7.25
184
160
73
95
43
152
69
84
38
3
80
15
381
7.5
190
22.75
578
11.38
289
22.38
568
20
508
16
406
8
203
350
159
169
77
260
118
150
68
4
100
18
457
9
229
26.5
673
13.25
337
25.25
641
22.5
572
16
406
8.5
216
520
236
263
119
420
191
228
103
5
125
22
559
11
279
31.25
794
15.63
397
28.25
718
25
635
20
508
8.5
216
900
408
570
259
840
381
475
215
6
150
24
610
12
305
36
914
18
457
37.63
956
33.75
857
28
711
11
279
1600
726
915
415
1480
671
795
361
8
200
29
737
14.5
368
40.25
1022
20.13
511
47.25
1200
42.25
1073
28
711
11.5
292
2400
1089
1730
785
2150
975
1480
671
10
250
33
838
16.5
419
50
1270
25
635
55.25
1403
48.75
1238
36
914
14
356
3200
1452
2480
1125
3360
1524
2140
971
12
300
38
965
19
483
56
1422
28
711
72.5
1842
69.5
1765
48
1219
16
406
5100
2313
3450
1565
4700
2132
3050
1383
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C63
Edward Valves
Dimensions - Angle
Figure No. 3907/3907Y, 4407Y
NPS
DN
14
350
20.25
514
67
1702
48
1219
18.5
470
5390
2445
NPS
DN
18
450
23.5
597
92
2337
72
1829
22
559
10,540
4781
20
500
23.5
597
92
2337
72
1829
22
559
10,620
4817
22
550
26
660
89.5
2273
72
1829
23
584
14,470
6564
24
600
28.5
724
96
2438
72
1829
24
610
18,340
8319
Dimensions - Flite-Flow
Figure No. 3902Y, 4402Y
16
400
20.25
514
67
1702
48
1219
18.5
470
5450
2472
3
80
17
432
20
508
16
408
9
229
230
104
4
100
18.5
470
25
635
16
406
10
254
325
147
6
150
24
610
37.5
953
28
711
11
279
890
404
8
200
30
762
41.75
1060
28
711
11.5
292
1610
730
10
250
36
914
50
1290
36
914
15.75
400
2750
1247
12
300
41
1041
65
1651
48
1219
17.5
445
4600
2087
14
350
48.75
1238
69
1753
48
1219
20.25
514
6990
3170
16
400
48.75
1238
69
1753
48
1219
20.25
514
7010
3179
18
20
24
450
500
600
58
58
68
1473
1473
1727
93.8
93.8
113
2383
2383
2870
72
72
72
1829
1829
1829
23.5
23.5
32
591
591
813
12,700 12,790 16,570
5760
5802
7516
C64
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9,
C12A, CF8M or CF8C).
Pressure-seal cover.
Integral Stellite seats.
Body-guided disk piston.
Equipped with equalizer.
TYPE
ENDS
4492Y
Flite-Flow
Buttwelding*
4494Y
4495Y
4470Y
Globe
Globe
Angle
Angle
Tilting Disk
Flanged
Buttwelding
Flanged*
Buttwelding
Buttwelding
STD CL
SPL CL
3992Y
3994
3994Y
3995
3995Y
2570Y
NPS (DN)
3 (80) thru
24 (600)
2-1/2 (65) thru
12 (300)
2-1/2 (65) thru
24 (600)
2-1/2 (65) thru 24(600)
NPS
DN
2-1/2
65
13
330
6.5
165
20
508
10
254
9.25
235
7.63
194
7.25
184
120
54
65
29
112
51
57
26
3
80
15
381
7.5
190
22.75
578
11.38
289
10.38
264
8.38
213
8
203
200
91
108
49
185
84
92
42
4
100
18
457
9
229
26.5
673
13.25
337
11.25
286
8.5
216
8.5
216
290
131
185
84
275
124
155
70
5
125
22
559
11
279
31.25
794
15.63
397
12.25
311
9
229
8.5
216
670
304
318
144
610
277
263
119
6
150
24
610
12
305
36
914
18
457
14
356
10.25
260
11
279
900
408
490
222
820
372
372
169
8
200
29
737
14.5
368
40.5
1022
20.13
511
17
432
12
305
11.5
292
1760
798
1010
458
1610
730
827
375
10
250
33
838
16.5
419
50
1270
25
635
19.25
489
12.75
324
14
356
2920
1324
1690
766
2520
1143
1284
582
12
300
38
965
19
483
56
1422
28
711
23
584
20
508
16
406
4070
1846
2420
1098
3860
1751
2210
1002
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C65
Edward Valves
Check Valves
Dimensions - Angle
Figure No. 3995/3995Y,
4495Y
NPS
DN
14
350
20.25
514
21.75
552
18.5
470
3210
1456
16
400
20.25
514
21.75
552
18.5
470
3270
1483
18
450
23.5
597
26.5
673
22
559
5570
2527
20
500
23.5
597
26.5
673
22
559
5650
2562
NPS
DN
24
600
28.5
724
33
838
24
610
10,550
4785
Dimensions - Flite-Flow
Figure No. 3992Y, 4492Y
22
550
26
660
30.5
775
23
584
8100
3674
3
80
17
432
10
254
9
229
150
68
4
100
18.5
470
11
279
10
254
225
102
6
150
24
610
14.25
362
11
279
510
230
8
200
30
762
18.75
476
11.5
292
950
431
10
250
36
914
22.25
565
15.75
400
1950
884
12
300
41
1041
26.75
679
17.5
445
2730
1238
14
350
48.75
1238
28.5
724
20.25
514
4300
1950
16
400
48.75
1238
28.5
724
20.25
514
4300
1950
18
450
58
1473
36.5
927
23.5
591
8100
3674
20
500
58
1473
36.5
927
23.5
591
8190
3715
24
600
68
1727
54
1372
32
813
12,620
5724
Note: Size 3&4 Buttweld Class 2500 Flite-Flow Valves are Class 2900. See page C67.
C66
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9, C12A, CF8M or CF8C).
Pressure-seal cover.
Integral Stellite seats.
C
Bold face numerals are in inches and pounds.
Blue numerals are in millimeters and kilograms.
NPS
DN
2-1/2*
65
12
305
7.25
184
10.5
267
95
43
3*
80
12
305
7.25
184
10.5
267
95
43
4*
100
12
305
7.25
184
10.5
267
95
43
6
150
24
610
9.5
241
15
381
435
197
8
200
30
762
10.5
267
18
457
800
363
10
250
36
914
12.5
318
20
508
1180
535
*Spiral wound hinge pin gaskets; hinge pin torsion spring not required.
NPS
DN
12
300
41
1041
15.75
400
24.25
616
2250
1021
14
350
44
1118
17.75
451
28.5
724
3200
1452
16
400
44
1118
17.75
451
28.5
724
3200
1452
18
450
55
1397
23.75
603
35
889
5580
2531
20
500
55
1397
23.75
603
35
889
5690
2581
24
600
63
1600
31
787
45
1143
13,200
5988
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C67
Edward Valves
Stop Valves
3914Y
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A,
CF8M, or CF8C).
Pressure-seal bonnet, OS & Y.
Y-Pattern.
Integral Stellite seat, disk and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
SPL CL
3914Y
4414Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 3914Y, 4414Y
A - End to End
E - Center to Top (Open)
G - Handwheel Diameter
Weight
C68
NPS
DN
3
80
17
432
20
508
16
406
230
104
4
100
18.5
470
25
635
16
406
325
147
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Standard Features
Bodies and bonnets are cast steel (WCB,
WC6, WC9, C12A, CF8M, or CF8C).
Pressure-seal bonnet, OS & Y.
Y-Pattern.
Integral Stellite seat, disk
and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Equipped with equalizer.
C
Pressure Class 2900 (PN 490)
FIG. NO.
STD CL
SPL CL
3902Y
4402Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 3902Y, 4402Y
A - End to End
E - Center to Top (Open)
G - Handwheel Diameter*
H - Equalizer Clearance
Weight
NPS
DN
3
80
17
432
20
508
16
406
9
229
230
104
4
100
18.5
470
25
635
16
406
10
254
325
147
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C69
Edward Valves
Check Valves
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9, C12A, CF8M,
or CF8C).
Pressure-seal cover.
Y-Pattern.
Integral Stellite seat and disk.
Body-guided disk piston.
Equipped with equalizer.
SPL CL
3992Y
4492Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 3992Y, 4492Y
A - End to End
E - Center to Top
H - Equalizer Clearance
Weight
C70
NPS
DN
3
80
17
432
10
254
9
229
150
68
4
100
18.5
470
11
279
10
254
225
102
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
Series 4500
THESE SERIES 4500 VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGE G59 FOR ADDITIONAL INFORMATION.
C
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A, CF8M or
CF8C).
Pressure-seal bonnet, OS & Y.
Y-Pattern.
Integral Stellite seats and backseat.
Body-guided disk piston.
13% chromium stainless steel stem.
Yoke bushing thrust bearings.
Series 4500
FIG. NO.
A - End to End
E - Center to Top, (Open)
G - Handwheel Diameter*
Weight
SPL CL
4514Y
5014Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Dimensions - Flite-Flow
Figure No. 4514Y, 5014Y
STD CL
NPS
DN
4
100
28
711
27.4
696
20
508
625
284
6
150
31
787
35
889
28
711
1360
617
8
200
31
787
48.25
1226
36
914
2510
1139
10
250
39.75
1010
52.75
1340
36
914
4020
1823
* Impactor handwheel is standard on size 4 & larger. Impactogear is available on size 6 and larger.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C71
Edward Valves
Series 4500
THESE SERIES 4500 VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGE G59 FOR ADDITIONAL INFORMATION.
Standard Features
Bodies and bonnets are cast steel
(WCB, WC6, WC9, C12A, CF8M or
CF8C).
Pressure-seal bonnet, OS & Y.
Y-Pattern.
Integral Stellite seats and backseats.
Body-guided disk piston.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Equipped with equalizer.
Yoke bushing thrust bearings.
Series 4500
FIG. NO.
A - End to End
E - Center to Top
G - Handwheel Diameter*
H - Equalizer Clearance
Weight
SPL CL
4502Y
5002Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
STD CL
NPS
DN
4
100
28
711
27.4
695
20
508
9.75
248
625
284
6
150
31
787
35
889
28
711
10.6
270
1360
617
8
200
31
787
48.25
1226
36
914
14.5
368
2510
1139
10
250
39.75
1010
52.75
1340
36
914
18.5
470
4020
1823
*Impactor handwheel is standard on size 4 & larger. Impactogear is available on size 6 and larger.
C72
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Check Valves
Series 4500
THESE SERIES 4500 VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGE G59 FOR ADDITIONAL INFORMATION.
C
Standard Features
Bodies and covers are cast steel (WCB, WC6,
WC9, C12A, CF8M or CF8C).
Pressure-seal cover.
Y-Pattern design.
Integral Stellite seats.
Body-guided disk piston.
Equipped with Equalizer.
A - End to End
E - Center to Top
H - Equalizer Clearance
Weight
FIG. NO.
STD CL
SPL CL
4592Y
5092Y
TYPE
ENDS
NPS (DN)
Flite-Flow
Buttwelding
Series 4500
NPS
DN
4
100
28
711
14
356
9.75
248
415
188
6
150
31
787
18
457
10.6
269
800
360
8
200
31
787
20
508
14.5
368
1500
675
10
250
39.75
1010
26
660
18.5
470
2300
1035
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
C73
Edward Valves
Check Valves
Standard Features
Bodies and covers are cast steel
(WCB, WC6, WC9, C12A,
CF8M or CF8C).
Pressure-seal cover.
Tilting Disk design.
Integral Stellite seats.
SPL CL
4570Y
5070Y
TYPE
ENDS
NPS (DN)
Tilting Disk
Buttwelding
C74
NPS
DN
6
150
20
508
10.25
260
17.5
445
520
234
8
200
24
610
11.375
289
19
483
1330
599
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
EV100
5th Edition
Edward Valves
NACE VALVES
(NATIONAL ASSOCIATION OF CORROSION ENGINEERS)
Edward can provide valves constructed of materials that meet NACE standard MR-01-75 for
sour service.
This standard entitled Sulfide Stress Cracking Resistant Metallic Materials For Oil Field Equipment
covers material requirements for production, drilling, gathering and flow line equipment used in
hydrogen sulfide bearing hydrocarbon service.
SPECIAL TRIM
Edward Valves provides a standard valve trim this is
compatible with the valve body chemistry, pressure
class, operating temperature, and fluid. However, on
application special trim materials to meet specific customer needs can be provided. Edward also can provide
cobalt free trim for nuclear applications.
NON-STANDARD ENDS
Most Edward forged and cast steel valves can be provided with welding ends or flanged ends (small forged
valves with threaded or socket weld ends also). On
special order non-standard ends can be furnished to
meet specific customer requirements. A partial list of
available options include:
GRAYLOC hubs.
Special flange facings.
Non-standard end-to-end lengths - most
Edward valves are manufactured to ANSI B16.10 criteria however, non- standard ends are available as a
special order.
Venturi ends.
Flanged by buttweld.
Blank ends.
Others as required.
D2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D3
Edward Valves
Blow-Off Valves
Class 300
Figure 1443
ANGLE
BLOW-OFF VALVE
Figure 1441
STRAIGHTWAY
BLOW-OFF VALVE
Standard Features
Size 1-1/2 and 2 bodies &
bonnets are forged steel (A105).
Size 2-1/2 bodies and bonnets are
cast steel (WCB).
Bolted bonnet, OS & Y.
Straightway and angle design.
Size 1-1/2 and 2 have hardened stainless steel disk.
Size 2-1/2 has Stellite faced disk.
Integral Stellite seat.
Integral backseat.
13% chromium stainless steel stem.
Asbestos free spiral wound
bonnet gasket.
Impactor handle.
1443/1441
D
Pressure Class 300 (PN 50)
FIG. NO.
1441
1441Y
1441Y
1443
1443Y
1443Y
TYPE
Globe
Globe
Globe
Angle
Angle
Angle
ENDS
Flanged
Socket Welding
Buttwelding
Flanged
Socket Welding
Buttwelding
NPS (DN)
1-1/2 (40) thru 2-1/2 (65)
1-1/2 (40) & 2 (50)
2-1/2 (65)
1-1/2 (40) thru 2-1/2 (65)
1-1/2 (40) & 2 (50)
2-1/2 (65)
Note:
D4
* This adjusted pressure rating represents the maximum allowable working pressure for this
Class valve in boiler feed and blow-off line service.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Blow-Off Valves
Class 300
NPS
DN
1-1/2
40
6.8
173
3.4
86
12
305
4.5
114
13.4
340
12.3
312
11
279
42
18.9
27
12.2
39
17.6
25
11.3
2
50
8
203
3.8
97
12.8
325
5.3
135
15.3
389
13.9
353
11
279
60
27
38
17.1
53
23.9
36
16.2
2-1/2
65
11.5
292
5.8
147
14
356
5.8
147
15.9
404
14.3
363
11
279
92
41.7
60
27
82
37.2
54
24.3
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D5
Edward Valves
Blow-Off Valves
Figure 1641
STRAIGHTWAY
BLOW-OFF VALVE
Standard Features
1643/1641
Angle
Globe
D
Pressure Class 400 (PN 68) & 600 (PN 110)
FIG. NO.
1641
1641Y
1641Y
1643
1643Y
1643Y
TYPE
Globe
Globe
Globe
Angle
Angle
Angle
ENDS
Flanged
Socket Welding
Buttwelding
Flanged
Socket Welding
Buttwelding
NPS (DN)
1-1/2 (40) thru 2-1/2 (65)
1-1/2 (40) & 2 (50)
2-1/2 (65)
1-1/2 (40) thru 2-1/2 (65)
1-1/2 (40) & 2 (50)
2-1/2 (65)
Note:
D6
* This adjusted pressure rating represents the maximum allowable working pressure for this
Class valve in boiler feed and blow-off line service.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Blow-Off Valves
1-1/2
40
6.8
173
3.4
86
12.4
315
4.8
122
13.4
340
12.4
315
11
279
44
19.8
27
12.2
41
18.5
25
11.3
2
50
8
203
3.8
97
13.1
333
5.8
147
15.3
389
13.9
353
11
279
62
27.9
38
17.1
55
24.8
36
16.2
2-1/2
65
11.5
292
5.8
147
14.4
366
6.5
165
15.9
404
14.3
363
11
279
95
43.1
76
34.2
85
38.5
66
29.7
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D7
Edward Valves
Blow-Off Valves
Standard construction Edward Class 1690 and Class 2680 carbon steel Univalves are supplied for Class 1500 and
Class 2500 Blow-Off valve applications.
Although these Univalves are manufactured and tagged to ANSI B16.34 Limited Class ratings, these valves meet and
exceed all Boiler Code criteria for boiler feed and blow-off line service.
Standard Features
Body Material is A105 carbon steel.
Unwelded (graphitic seal) or
welded bonnet.
OS & Y.
Y-Pattern.
Body-guided investment cast
Stellite disk.
Integral Stellite seat.
Asbestos free graphitic packing.
Impactor Handle/Impactor Handwheel.
UNWELD
1500
2500
1500
2500
36124
36128
66124
66128
36224
36228
66224
66228
TYPE
ENDS
NPS (DN)
Globe
Globe
Socket Welding
Buttwelding
Class 1500
Primary Service
2455 PSI
(169.3 BAR)
3705 PSI @ 100F
(255.5 BAR)
Class 2500
Primary Service
3206 PSI#
(221.1 BAR)
6170 PSI @ 100F
(425.5 BAR)
* This adjusted pressure rating represents the maximum allowable working pressure for this Class valve in boiler feed
and blow-off line service.
# Rating exceeds critical pressure of water.
Refer to Forged Steel Section, Pages B-15 and B-18 - Univalve Stop Valve, Class 1690 and 2680 for dimensions, etc.
Note:
D8
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Elbow Down
Edward Elbow Down stop-check valves are available for special service requirements.
Because they eliminate the need for a piping elbow, and at the same time offer tight shut-off with minimum
pressure drop, they are commonly used at discharge of circulating pumps on controlled circulation boilers.
Standard Features
Bodies and bonnets/covers are cast
steel (WCB or WC6).
Pressure seal bonnet/cover.
Integral Stellite seat, disk seating &
backseat.
Disk body-guided.
Impactor handwheel/impactogear.
Equipped with equalizer.
Buttwelding ends.
Asbestos free packing.
Elbow Down*
FIG. NO.
TYPE
ENDS
NPS (DN)
4448Y
4498Y
7548Y
7598Y
Stop Check
Check
Stop Check
Check
Buttwelding
Buttwelding
Buttwelding
Buttwelding
10 (250)
thru 16 (400)
10 (250)
thru 18 (450)
Dimensions
NPS
DN
10
250
23
584
12.25
311
12
300
27.56
700
14.56
370
14
350
35.06
891
18.94
481
16
400
34
864
18.56
471
Dimensions
Figure No. 7548Y, 7598Y
A - Center to End, (Inlet)
B - Center to End, (Outlet)
NPS
DN
10
250
23
584
13
330
12
300
27
675
14
356
14
350
29
737
15
381
16
400
36
914
17
432
18
450
39.25
997
21.25
540
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D9
Edward Valves
THESE HYDRAULIC VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGES G59-G60 FOR ADDITIONAL INFORMATION.
Standard Features
Body is of forged alloy steel grade F-11.
Bonnet is zinc coated for corrosion
resistance.
13% chromium stainless steel replaceable
seat.
13% chromium stainless steel stem and
swivel needle disk.
Hardfaced seat and disk standard on Figure
5158 & 9158 valves only.
Impactor handle, size 1 and
larger.
Buna-N O rings at body-bonnet and body
seat joints for leak-tight connection.
Asbestos free packing.
10,000
158
158Y
5158
ENDS
Globe
Globe
Threaded
Socket Welding
Flanged
Series 1500
Flanged
Series 6BX
Globe
9158
Globe
NPS (DN)
1/4 (6) thru 2 (50)
2 (50)
2-1/16 (52.4) only
For Pressure up to 10,000 PSI (690 BAR) - Edward high pressure forged steel hydraulic stop
valves are used in applications involving high pressures and with temperatures to 300F
(149C). They provide fast, certain shut-off or accurate pressure control, give long life, reduce
replacement costs and lower maintenance time.
Dimensions
Figure No. 158/158Y, 5158,
9158
TYPE
NPS
DN
1/4
8
3.8
97
8.4
213
5.4
134
5.1
2.3
3/8
10
3.8
97
8.4
213
5.4
137
5.1
2.3
1/2
15
3.8
97
8.4
213
5.4
137
5.1
2.3
3/4
20
4.5
114
9.6
244
6.4
163
6.8
3.1
1
25
5.1
130
12
305
11*
279
12.5
5.6
1-1/4
40
7.5
191
14.1
358
11*
279
32
14.4
1-1/2
40
7.5
191
14.1
358
11*
279
32
14.4
2
50
9
229
18
457
14*
356
53
23.9
2 (5158) 2-1/16
50
52.4
13.4
13.3
340
338
17.9
17.9
455
455
14*
14*
356
356
8.5
7.9
216
201
1.8
1.7
46
43
3-3/4-#24 BX-152
6.5
6.25
165
160
(8)-7/8 (8)-3/4
120
124
54
55.8
Flanges, Ring Joint Facings and Drilling according to A.P.I. standards. Size depicts flange size only and not port size. * Impactor Handle.
D10
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
THESE HYDRAULIC VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGES G59-G60 FOR ADDITIONAL INFORMATION.
Standard Features
TYPE
ENDS
Globe
Globe
Threaded
Socket Welding
Flanged*
Series 1500
Flanged*
Series 6BX
10,000
160
160Y
5160
Globe
9160
Globe
A - End to End
C - Contact Face to
Contact Face
E - Center to Top
T - Flange Diameter
U - Flange Thickness
Diameter of Ring Groove &
Groove Number
Diameter of Bolt Circle
Bolts
Weight
Dimensions
Figure No. 160/160Y, 5160,
9160
NPS (DN)
NPS
DN
1/4
8
3.8
97
3
76
2.6
1.2
3/8
10
3.8
97
3
76
2.6
1.2
1/2
15
3.8
97
3
76
2.6
1.2
3/4
20
4.5
114
3.3
84
4
1.8
1
25
5.1
130
4.4
112
7
3.2
1-1/4
40
7.5
191
5.2
132
19
8.6
1-1/2
40
7.5
191
5.2
132
19
8.6
2
50
9
229
7.3
185
34
15.3
2-1/16
52.4
13.3
338
6.1
155
7.9
201
1.7
43
3-3/4-#24 BX-152
95
6.5
6.25
165
159
(8)-7/8 (8)-3/4
101
105
45.5
47.3
2 (5150)
50
13.4
340
6.1
155
8.5
216
1.8
46
* Flanges, Ring Joint Facings and Drilling according to A.P.I. standards. Size depicts flange size only and not port size.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D11
Edward Valves
Stop Valves
THESE SERIES 1500 VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGES G59-G60 FOR ADDITIONAL INFORMATION.
Standard Features
Bodies and bonnets are of forged steel
(F11).
Bolted bonnet, OS & Y.
Globe or angle design.
Body-guided hardened stainless steel disk.
Integral Stellite seat.
Integral backseat.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Asbestos free spiral wound
bonnet gasket.
Knobbed handwheel.
D12
FIG. NO.
1028
1029
TYPE
Globe
Angle
ENDS
Flanged
Flanged
NPS (DN)
1/2 (15) thru
2 (50)
Series 1500
NPS
DN
1/2
15
8.5
216
4.3
109
7
178
6.6
168
4.3
109
15
6.8
15
6.8
3/4
20
9
229
4.5
114
7.7
196
7.1
180
4.8
122
19
8.6
20
9
1
25
10
254
5
127
7.7
196
7.1
180
4.8
122
26
11.7
26
11.7
1-1/4
32
12
305
6
152
11.1
282
10.2
259
7.1
180
38
17.1
41
18.5
1-1/2
40
12
305
6
152
11.1
282
10.2
259
7.1
180
47
21.2
49
22.1
2
50
14.5
368
7.3
185
12
305
11.1
282
8.5
216
77
34.7
80
36
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop Valves
THESE SERIES 1500 VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGES G59-G60 FOR ADDITIONAL INFORMATION.
Standard Features
Bodies and bonnets are of
forged steel (A105 or F11).
Bolted bonnet, OS & Y.
Y-Pattern or angle design.
Body-guided hardened stainless steel disk.
Integral Stellite seat.
Integral backseat.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Asbestos free spiral wound
bonnet gasket.
Knobbed handwheel.
FIG. NO.
1048
1048Y
1049
1049Y
TYPE
Y-Pattern
Y-Pattern
Angle
Angle
ENDS
Threaded
Socket Welding
Threaded
Socket Welding
NPS (DN)
1/4 (6)
thru
2 (50)
Series 1500
NPS
DN
1/4
8
3
76
1.5
38
6.1
155
5.8
147
3.8
97
4
1.8
4
1.8
3/8
10
3
76
1.5
38
6.1
155
5.8
147
3.8
97
4
1.8
4
1.8
1/2
15
3
76
1.5
38
6.1
155
5.8
147
3.8
97
4
1.8
4
1.8
3/4
20
3.6
91
1.8
46
6.9
175
6.6
168
4.3
109
5.5
2.5
5.5
2.5
1
25
4.3
109
2
51
7.6
197
7.1
183
4.8
122
8
3.6
7.5
3.4
1-1/4
32
5.8
147
2.9
74
10.9
277
10.2
259
7.1
183
17
7.7
17
7.7
1-1/2
40
5.8
147
2.9
74
10.9
277
10.2
259
7.1
183
17
7.7
17
7.7
2
50
6.5
165
3.3
84
12.1
307
11
279
8.5
216
24
10.8
25
11.3
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D13
Edward Valves
Stop-Check Valves
THESE SERIES 1500 VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGES G59-G60 FOR ADDITIONAL INFORMATION.
Standard Features
D14
FIG. NO.
1046
1047
TYPE
Globe
Angle
ENDS
Flanged
Flanged
NPS (DN)
1/2 (15) thru
2 (50)
Series 1500
NPS
DN
1/2
15
8.5
216
4.3
109
7
178
6.6
168
4.3
109
15
6.8
15
6.8
3/4
20
9
229
4.5
114
7.7
196
7.1
180
4.8
122
19
8.6
20
9
1
25
10
254
5
127
7.7
196
7.1
180
4.8
122
26
11.7
26
11.7
1-1/4
32
12
305
6
152
11.1
282
10.2
259
7.1
180
38
17.1
41
18.5
1-1/2
40
12
305
6
152
11.1
282
10.2
259
7.1
180
47
21.2
49
22.1
2
50
14.5
368
7.3
185
12
305
11.1
282
8.5
216
77
34.7
80
36
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Stop-Check Valves
THESE SERIES 1500 VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGES G59-G60 FOR ADDITIONAL INFORMATION.
Standard Features
Bodies and bonnets are of forged
steel (A105 or F11).
Bolted bonnet, OS & Y.
Y-Pattern or angle design.
Body-guided hardened stainless steel
disk.
Integral Stellite seat.
Integral backseat.
13% chromium stainless steel stem.
Asbestos free graphitic packing.
Asbestos free spiral wound
bonnet gasket.
Knobbed handwheel.
Stainless steel spring.
FIG. NO.
1068
1068Y
1069
1069Y
TYPE
Y-Pattern
Y-Pattern
Angle
Angle
ENDS
Threaded
Socket Welding
Threaded
Socket Welding
NPS (DN)
1/4 (8)
thru
2 (50)
Series 1500
NPS
DN
1/4
8
3
76
1.5
38
6.1
155
5.8
147
3.8
97
4
1.8
4
1.8
3/8
10
3
76
1.5
38
6.1
155
5.8
147
3.8
97
4
1.8
4
1.8
1/2
15
3
76
1.5
38
6.1
155
5.8
147
3.8
97
4
1.8
4
1.8
3/4
20
3.6
91
1.8
46
6.9
175
6.6
168
4.3
109
5.5
2.5
5.5
2.5
1
25
4.3
109
2
51
7.6
193
7.1
180
4.8
122
8
3.6
7.5
3.4
1-1/4
32
5.8
147
2.9
74
10.9
277
10.2
259
7.1
180
16
7.3
16
7.3
1-1/2
40
5.8
147
2.9
74
10.9
277
10.2
259
7.1
180
16
7.3
16
7.3
2
50
6.5
165
3.3
84
12.1
307
11
279
8.5
216
23
10.4
24
10.9
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D15
Edward Valves
THESE SERIES 1500 VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGES G59-G60 FOR ADDITIONAL INFORMATION.
Standard Features
Bodies and covers are of forged steel
(A105 or F11).
Bolted cover.
Y-Pattern or globe design.
Body-guided hardened stainless steel
disk.
Integral Stellite seat.
Asbestos free spiral wound cover
gasket.
Stainless steel spring.
D
Series 1500
FIG. NO.
1038
1038Y
1058 (F11)
ENDS
Threaded
Socket Welding
Flanged
NPS (DN)
1/4 (8) thru
2 (50)
1/2 (15) thru 2 (50)
Dimensions - Globe
Figure No. 1038/1038Y
TYPE
Y-Pattern
Y-Pattern
Globe
NPS
DN
1/4
8
3
76
2.8
71
2.5
1.1
3/8
10
3
76
2.8
71
2.5
1.1
1/2
15
3
76
2.8
71
2.5
1.1
3/4
20
3.6
91
3.3
84
3.5
1.6
1
25
4.3
109
3.8
97
5.5
2.5
1-1/4
32
5.8
147
4.6
117
11
5
NPS
DN
1/2
15
8.5
216
2.7
69
14
6.3
3/4
20
9
229
3.1
79
17
7.7
1
25
10
254
3.1
79
24
10.8
1-1/4
32
12
305
4.2
197
32
14.4
1-1/2
40
12
305
4.2
107
41
18.5
2
50
14.5
368
4.7
119
69
31.1
A - End to End
E - Center to Top
Weight
1-1/2
40
5.8
147
4.6
117
11
5
2
50
6.5
165
5.1
130
15
6.8
Dimensions - Globe
Figure No. 1058
C - Face to Face (Flanged)
E - Center to Top
Weight
D16
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
THESE SERIES 1500 VALVES ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGES G59-G60 FOR ADDITIONAL INFORMATION.
Standard Features
Bodies and covers are of forged steel
(A105 or F11).
Bolted cover.
Y-Pattern.
Integral Stellite seat.
Asbestos free spiral wound
bonnet gasket.
Stainless steel spring.
Stainless steel ball.
Series 1500
FIG. NO.
1032
1032Y
TYPE
Y-Pattern
Y-Pattern
A - End to End
E - Center to Top
Weight
NPS (DN)
1/4 (8) thru
2 (50)
Dimensions - Globe
Figure No. 1032/1032Y
ENDS
Threaded
Socket Welding
NPS
DN
1/4
8
3
76
2.8
71
2.5
1.1
3/8
10
3
76
2.8
71
2.5
1.1
1/2
15
3
76
2.8
71
2.5
1.1
3/4
20
3.6
91
3.3
84
3.5
1.6
1
25
4.3
109
3.8
97
5.5
2.5
1-1/4
32
5.8
147
4.6
117
11
5
1-1/2
40
5.8
147
4.6
117
11
5
2
50
6.5
165
5.1
130
15
6.8
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D17
Edward Valves
Strainers
THE CLASS 800 STRAINERS ARE RATED IN ACCORDANCE WITH ASME/ANSI B16.34 CRITERIA.
THE SERIES 1500 STRAINERS ARE DESIGNED AND RATED TO EDWARD VALVE STANDARDS.
SEE PARAGRAPH 3.2, PAGES G59-G60 FOR ADDITIONAL INFORMATION.
Standard Features
Bodies and covers are of forged carbon
steel.
Screen is stainless steel.
Screen specification (400,
.027 dia. holes per square inch).
Removable drain plug for easy cleaning.
A - End to End
L - Center to Bottom
Plug Size (NPT)
Weight
NPS (DN)
Threaded
Socket Welding
ENDS
NPS
DN
1/4
8
3
76
3.4
86
1/4
6
2
.9
3/8
10
3
76
3.4
86
1/4
6
2
.9
1/2
15
3
76
3.4
86
1/4
6
2
.9
3/4
20
3.6
91
4.8
122
1/4
6
4
1.8
1
25
4.3
109
6.1
155
1/2
13
6
2.7
1-1/4
32
5.8
147
10.4
264
1/2
13
13
5.9
1-1/2
40
5.8
147
10.4
264
1/2
13
13
5.9
2
50
6.5
165
12.1
307
1/2
13
20
9
Special interior surface preparation for corrosive and erosive water services available on size 1 (DN 25) only.
D18
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Standard Features
Available Body Materials
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
F316 stainless steel.
Unwelded (graphitic seal) or welded
bonnet.
OS & Y.
Y-Pattern.
Body-guided investment cast
Stellite disk.
Integral Stellite seat.
Integral backseat.
Asbestos free graphitic packing.
Dimensions - Globe
Figure No. 36122
36222
A - End to End
AB - Handwheel Clearance, (Open)
B - Center to End
E - Center to Top, (Open)
G - Handwheel/Handle Diameter
Weight, Welded & Unwelded
UNWELD.
36122
36222
TYPE
ENDS
NPS (DN)
Y-Pattern
Flanged
1/2
15
10.0
25.4
3.0
76.2
6.9
175
11.6
295
8.5
216
31
14.1
3/4
20
10.0
254
3.0
76.2
6.9
175
11.6
295
8.5
216
34
15.5
1
25
10.0
254
3.0
76.2
6.9
175
11.6
295
8.5
216
36
16.4
1-1/2
40
12.0
305
5.3
135
8.3
211
16.3
414
14.3*
363*
75
34
2
50
14.5
368
4.9
125
10.0
254
18.5
470
14.3*
363*
120
55
* Impactor Handle
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D19
Edward Valves
7.
1.
14.
1.
10.
11.
11.
10.
2.
12.
12.
2.
13.
13.
3.
3.
17.
15.
4.
4.
5.
5.
16.
6.
2. Yoke bushing material has low coefficient of friction which substantially reduces torque and stem
wear and eliminates galling. Mechanical upset locks
bushing to yoke.
15. PressurSeat features live-loaded, pressureenergized Stellite seat, providing tight shut-off under
varying pressures and temperatures.
D20
9. Threaded bonnet has ACME threads for resistance to galling and ease of disassembly.
10. Stem packing system utilizes flexible graphite
packing material with carbon fiber anti-extrusion
rings for optimum sealability and life.
11. Bonnet locking collar.
12. Bonnet seal ring is die formed flexible graphite
seated to a prescribed bonnet torque to provide reliable bonnet seal.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
PressurCombo
Standard Features
Available Body Material
A105 carbon steel.
Flow, DP
F22 alloy steel.
F91 alloy steel.
Available as tandem assembly or individual
valves.**
Unwelded (graphitic seal) or welded bonnet.
OS & Y.
Y-Pattern.
Pressure Class 1690 (PN 290)
Body-guided investment cast Stellite disk.
FIG. NO.
Investment cast Stellite seat in PressurSeat
TYPE
ENDS
WELDED UNWELD.
and PressurCombo.
**36124 **36224 Y-Pattern
Socket Welding
Integral Stellite seat in PressurEater.
**36128 **36228 Y-Pattern
Buttwelding
PressurEater & PressurCombo have outlet
** DS36xxx PressurSeat
Inv. cast Stellite seat
DE36xxx PressurEater
Integral Stellite seat, choke
choke/nozzles.
DC36xxx PressurCombo
Inv. cast Stellite seat, choke
Integral Stellite backseat.
Asbestos free graphitic packing.
PressurSeat and PressurCombo have position
indicators.
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
E - 1 Center to Top, (Open)
E - 2 Center to Top (Open)
G - 1 Handwheel/Handle Diameter
G - 2 Handwheel/Handle Diameter
Weight, Welded (Tandem DS/DE)
Weight, Unwelded (Tandem DS/DE)
* Impactor Handle
** Impactor Handwheel
Dimensions - Globe
Figure No. **36124, **36128,
**36224, **36228
NPS (DN)
NPS
DN
1/2
15
6
152
3.20
81
7.8
198
12.2
310
12.1
307
8.5
216
8.5
216
51
23
53
24
3/4
20
6
152
3.20
81
7.8
198
12.2
310
12.1
307
8.5
216
8.5
216
51
23
53
24
1
25
6
152
3.20
81
7.8
198
12.2
310
12.1
307
8.5
216
8.5
216
51
23
53
24
1-1/4
32
6.7
170
3.20
81
9.8
249
13.7
348
14.6
371
8.5
216
11.0*
279
79
36
83
38
1-1/2
40
6.7
170
3.20
81
9.8
249
13.7
348
14.6
371
8.5
216
11.0*
279
79
36
83
38
2
50
8.2
208
3.64
92
11.6
295
17.1
434
17.7
450
14.0
356
14.3*
363*
124
56
128
58
2-1/2
65
10.7
272
4.00
102
12.5
318
20.3
516
19.6
498
18.0
457
16.0**
406**
210
95
218
99
3
80
10.7
272
4.00
102
12.5
318
20.3
516
19.6
498
18.0
457
16.0**
406**
210
95
218
99
4
100
12.8
325
4.8
122
11.2
284
20.7
526
20.0
508
18.0
457
16.0**
406**
286
130
294
133
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D21
Edward Valves
PressurCombo
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
Flow, DP
F91 alloy steel.
Available as tandem assembly
or individual valves.**
Unwelded (graphitic seal) or welded bonnet.
OS & Y.
Y-Pattern.
Body-guided investment cast Stellite disk.
Investment cast Stellite seat in PressurSeat
and PressurCombo.
Integral Stellite seat in PressurEater.
PressurEater & PressurCombo have outlet
choke/nozzles.
Integral Stellite backseat.
Asbestos free graphitic packing.
PressurSeat and PressurCombo have
position indicators.
UNWELD.
**66124 **66224
**66128 **66228
** DS66xxx PressurSeat
DE66xxx PressurEater
DC66xxx PressurCombo
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
E - 1 Center to Top, (Open)
E - 2 Center to Top (Open)
G - 1 Handwheel/Handle Diameter
G - 2 Handwheel/Handle Diameter
Weight, Welded (Tandem DS/DE)
Weight, Unwelded (Tandem DS/DE)
* Impactor Handle
D22
** Impactor Handwheel
ENDS
NPS (DN)
Y-Pattern
Y-Pattern
Socket Welding
Buttwelding
Dimensions - Globe
Figure No. **66124, **66128,
**66224, **66228
TYPE
NPS
DN
1/2
15
6
152
3.20
81
7.8
198
12.2
310
12.1
307
8.5
216
8.5
216
51
23
53
24
3/4
20
6
152
3.20
81
7.8
198
12.2
310
12.1
307
8.5
216
8.5
216
51
23
53
24
1
25
6
152
3.20
81
7.8
198
12.2
310
12.1
307
8.5
216
8.5
216
51
23
53
24
1-1/4
32
6.7
170
3.20
81
9.8
249
13.7
348
14.6
371
8.5
216
11*
279*
79
36
83
38
1-1/2
40
6.7
170
3.20
81
9.8
249
13.7
348
14.6
371
8.5
216
11*
279*
79
36
83
38
2
50
10.7
272
4.00
102
11.6
295
18.5
470
18.6
472
14
356
14.3*
363*
167
76
169
77
2-1/2
65
12.8
325
4.80
122
11.2
285
20.7
526
20.0
508
18
457
16**
406**
298
135
306
139
3
80
12.8
325
4.80
122
11.2
285
20.7
526
20.0
508
18
457
16**
406**
298
135
306
139
4
100
12.8
325
4.80
122
11.2
285
20.7
526
20.0
508
18
457
16**
406**
298
135
306
139
Weights are listed for tandem assembly combo. Flow coefficients are listed on page G32.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
PressurCombo
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F91 alloy steel.
Flow, DP
Available as tandem assembly
or individual valves.**
Unwelded (graphitic seal) or
welded bonnet.
OS & Y.
Pressure Class 4500 (PN 760)
Y-Pattern.
FIG. NO.
Body-guided investment cast
TYPE
ENDS
WELDED UNWELD.
Stellite disk.
**96124 **96224 Y-Pattern
Socket Welding
Investment cast Stellite seat in PressurSeat
**96128
**96228
Y-Pattern
Buttwelding
and PressurCombo.
** DS96xxx PressurSeat
Inv. cast Stellite seat
Integral Stellite seat in PressurEater.
DE96xxx PressurEater
Integral Stellite seat, choke
PressurEater & PressurCombo have outlet
DC696xxx PressurCombo
Inv. cast Stellite seat, choke
choke/nozzles.
Integral Stellite backseat.
Asbestos free graphitic packing.
PressurSeat and PressurCombo have position indicators.
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
E - 1 Center to Top, (Open)
E - 2 Center to Top (Open)
G - 1 Handwheel/Handle Diameter
G - 2 Handwheel/Handle Diameter
Weight, Welded (Tandem DS/DE)
Weight, Unwelded (Tandem DS/DE)
** Impactor Handwheel
Dimensions - Globe
Figure No. **96124, **96128,
**96224, **96228
NPS (DN)
NPS
DN
1/2
15
8.2
208
3.64
92
7.3
185
13.1
333
13.4
340
8.5
216
8.5
216
90
41
94
43
3/4
20
8.2
208
3.64
92
7.3
185
13.1
333
13.4
340
8.5
216
8.5
216
90
41
94
43
1
25
8.2
208
3.64
92
7.3
185
13.1
333
13.4
340
8.5
216
8.5
216
90
41
94
43
1-1/4
32
8.2
208
3.64
92
7.3
185
13.1
333
13.4
340
8.5
216
8.5
216
90
41
94
43
1-1/2
40
8.2
208
3.64
92
7.3
185
13.1
333
13.4
340
8.5
216
8.5
216
90
41
94
43
2
50
12.8
325
4.80
122
11.2
284
19.1
485
20.0
508
14.0
356
16.0**
406**
320
145
328
149
2-1/2
65
12.8
325
4.80
122
11.2
284
19.1
485
20.0
508
14.0
356
16.0**
406**
320
145
328
149
3
80
12.8
325
4.80
122
11.2
284
19.1
485
20.0
508
14.0
356
16.0**
406**
320
145
328
149
4
100
12.8
325
4.80
122
11.2
284
19.1
485
20.0
508
14.0
356
16.0**
406**
320
145
328
149
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D23
Edward Valves
18.
1.
17.
2.
16.
15.
3.
4.
14.
13.
5.
12.
6.
7.
8.
9.
11.
D24
10.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
What is a Hermavalve? A Hermavalve is a hermetically sealed valve that cannot leak to the environment. The Edward Hermavalve cannot leak because it is
double seal welded:
1. The multi-ply flexible metal diaphragm is seal welded to the bonnet.
3. Needle thrust bearings minimize torque. Their upper yoke location protects
from heat and allows lubrication.
4. Yoke bushing. Revolving bushing of aluminum bronze material has low
coefficient of friction, substantially reduces torque, stem wear and eliminates galling.
5. Non-revolving stem is stainless steel. It is ground to a fine finish and keyed
to the yoke to prevent rotation and torsional stress on the diaphragm.
6. Yoke of carbon steel.
7. Diaphragm disk is a unique patented shape which maximizes diaphragm life.
8. Diaphragm of multi-ply flexible metal provides a reliable primary stem seal.
9. Body with inclined stem construction and unique flow shape minimizes
flow directional changes and cuts pressure drop.
10. Integral hardfaced seat of hard, heat resistant hardfacing material is integrally welded to the body.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D25
Edward Valves
DESCRIPTION
ASTM NO.
ASTM NO.
ASTM NO.
Body
A-105
Disk
A-732 Grade 21
Stellite 21
Stellite 21
Stellite 21
A-582 T416
A-582 T416
A-582 T416
Bonnet
A-696 Grade C
A-479 T316
Yoke Bolt
A-307 Grade A
A-307 Grade A
A-307 Grade A
A-696 Grade C
A-696 Grade C
A-696 Grade C
Body Seat
Stem
Junk Ring
Packing
Gland
Retaining Ring
Gland Adjusting Screw
A-193 Grade B6
A-193 Grade B6
A-194 Grade B6
A-563 Grade A
A-563 Grade A
A-563 Grade A
Yoke
Yoke Bushing
B-150 Alloy
C61900 or C62300
B-150 Alloy
C61900 or C62300
B-150 Alloy
C61900 or C62300
Alloy Steel
Alloy Steel
Alloy Steel
A-582 T416
A-582 T416
A-479 T316
Diaphragm Ring
A-696 Grade C
A-479 T316
Diaphragm Assembly
Diaphragm Disk
A-732 Grade 21
A-732 Grade 21
A-732 Grade 21
A-167 T316
A-167 T316
A-167 T316
A-479 T316
Inconel X-750
Inconel X-750
Inconel X-750
Steel
Steel
Steel
A-479 T316
A-479 T316
A-479 T316
Thrust Bearing
Steel
Steel
Steel
Lube Fitting
Steel
Steel
Steel
Drive Pin
Key
Spring Housing
Shims
Disk Collar
Spring
Handwheel
Handwheel Nut
Indicator
D26
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Standard Features
Available Body Material
A105 carbon steel.
F22 alloy steel.
F316 stainless steel.
Seal welded diaphragm and seal
welded body/bonnet joint.
OS & Y.
Y-Pattern.
Non-revolving stem with position
indicator.
Back-up asbestos free graphitic packing and secondary stem backseat.
Integral backseat.
Knobbed handwheel.
TYPE
ENDS
PORT
NPS (DN)
16004
16008
16014
16018
Y-Pattern
Y-Pattern
Y-Pattern
Y-Pattern
Socket Welding
Buttwelding
Socket Welding
Buttwelding
Regular
Regular
Reduced
Reduced
Dimensions
Figure No. 16004, 16008, 16014
16018
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
E - Center to Top
B - Center to End
G - Handwheel Diameter
Weight
REGULAR
NPS
DN
1/2
15
5.5
140
2.06
52
4.62
117
9.12
232
3.8
97
7.12
181
18
8
3/4
20
5.5
140
2.06
52
4.62
117
9.12
232
3.8
97
7.12
181
18
8
1
25
6.62
168
2.12
54
5.69
145
11.19
284
4.62
117
8.5
216
30
14
REDUCED
1-1/2
40
8.7
220
3.4
86
9.06
230
16
406
6
152
11.5
292
73
33
2
50
10
254
3.4
86
10.88
276
18.5
470
6.86
174
15
381
106
48
1
25
5.5
140
2.06
52
4.62
117
9.12
232
3.8
97
7.12
181
18
8
1-1/2*
40
6.62
168
2.12
54
5.69
145
11.19
284
4.62
117
8.5
216
30
14
2
50
8.7
220
3.4
86
9.06
230
16
406
6
152
11.5
292
73
33
2-1/2
65
10
254
3.4
86
10.88
276
18.5
470
6.86
174
15
381
106
48
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
D27
Edward Valves
Standard Features
AA
B
B
Orifice Number1
Orifice Size
-2
-3
-4
-5
-6
-7
-8
-10
0.12
0.18
0.25
0.31
0.38
0.44
0.50
0.62
Butt Welding
-12
-14
-16
0.75 (19)
0.88 (22)
1.00 (25)
Butt Welding
-18
-20
1.12 (29)
1.25 (32)
Welded
Bonnet
Unwelded
Bonnet
Ends
35125
35225
Socket Welding
35129
35229
Butt Welding
35129
35229
Butt Welding
35125
35225
Socket Welding3
DN 40 thru 80
35129
35229
35129
35229
(3)
(5)
(6)
(8)
(10)
(11)
(13)
(16)
1. Orifice number is added to Figure Numbers shown to form complete figure number (ie: 35125-7).
2. Valve sizes 2-1/2 and smaller are ANSI B16.34 Limited Class. Size 3&4 valves are Special Class.
3. Socket Welding ends are not available in Size 3 valves.
Dimensions
Orifice Number
Valve Sizes
AA
Hub Diameter
B
Center to Face
-2 thru -10
1 thru 2-1/2
3.0
76
1-1/4 thru 3
2-1/2 thru 4
* Impactor Handle
D28
G
Handwheel/
Handle Diameter
8.5
216
W
Weight
2.6
67
E
Center to Top
(open)
11.1
282
3.8
97
3.6
91
14.7
373
11*
279
45
20
4.8
122
5.3
135
19.7
500
16**
406
130
59
25
11
** Impactor Handwheel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
EV100
5th Edition
Edward Valves
Edward Equiwedge gate valve with an Edward gas hydraulic actuator being prepared for shipment.
All Edward valves constructed for Nuclear service can be offered for Code class 1, 2 or 3.
E2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Most Edward Forged and Cast Steel Valves can be supplied for nuclear service. The following chart summarizes past Edward
experience by Type, Size Range and Pressure Class. Consult your Edward Valves sales representative for additional information.
VALVE TYPE
SIZE
ANSI RATINGS
Bolted Bonnet
Hermavalve
Univalve
Equiwedge Gate
Flite-Flow Globe
(Stop, Stop-Check & Check)
Cast Steel
Tilting Disk
Edward Globe & Angle
(Stop, Stop-Check & Check)
Controlled Closure Check Valve
(see page E-14)
Soft-seated Check Valve
Actuators
(U stamped)
1/4 Turn Valve
Note: See page III for indicated figure numbers available for nuclear service.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
E3
Edward Valves
18.
1.
17.
2.
16.
15.
3.
4.
14.
13.
5.
12.
6.
7.
8.
9.
11.
E4
10.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
What is a Hermavalve? A Hermavalve is a hermetically sealed valve that cannot leak to the environment. The Edward Hermavalve cannot leak because it is
double seal welded:
1. The multi-ply flexible metal diaphragm is seal welded to the bonnet.
3. Needle thrust bearings minimize torque. Their upper yoke location protects
from heat and allows lubrication.
4. Yoke bushing. Revolving busing of aluminum bronze material has low coefficient of friction, substantially reduces torque, stem wear and eliminates galling.
This patented construction eliminates any potential leakage through a mechanical joint. It is more than just packless, it is hermetically sealed.
12. Disk guide assembly assures disk/seat alignment. Its completely encapsulated spring assures full disk lift.
13. Diaphragm seal weld is a unique seal weld which makes the diaphragm an
integral part of the bonnet and eliminates a potential leak path past the stem.
14. Backseat provides a secondary stem seal backup.
15. Body-bonnet seal features leak-proof seal-welded construction. The weld is
for seal only; the threaded section carries the pressure load. Canopy weld in
stainless steel; fillet weld in carbon steel.
16. Bonnet is barstock steel with gall-resistant ACME threads to insure easy disassembly from body.
17. Backup packing with OS & Y design allows for inspection or
addition of packing without disassembling valve.
18. Adjustable gland screws with OS & Y design allow for easy access to packing adjustment if necessary.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
E5
Edward Valves
Standard Features
SA105 or SA182 Grade F316 body
and bonnet.
Seal welded diaphragm and seal welded body/bonnet joint.
OS & Y.
Y-Pattern.
Non-revolving stem with position
indicator.
Back-up asbestos free graphitic packing and secondary stem backseat.
Integral hardfaced seat.
Knobbed handwheel.
MATERIAL
Carbon Steel
Carbon Steel
Carbon Steel
Carbon Steel
Stainless Steel
Stainless Steel
Stainless Steel
Stainless Steel
ENDS
Socket Welding
Buttwelding
Socket Welding
Buttwelding
Socket Welding
Buttwelding
Socket Welding
Buttwelding
PORT
Regular
Regular
Reduced
Reduced
Regular
Regular
Reduced
Reduced
NPS (DN)
1/2 (15) thru
2 (50)
1 (25) thru
2-1/2 (40)
1/2 (15) thru
2 (50)
1 (25) thru
2-1/2 (40)
Dimensions
Figure No. 15004, 15008, 15014
15018, 15104, 15108, 15114, 15118
A - End to End
AA - End Hub Diameter
AB - Handwheel Clearance, (Open)
E - Center to Top
B - Center to End
G - Handwheel Diameter
Weight
NPS
DN
1/2
15
5.5
140
2.06
52
4.62
117
9.12
232
3.8
97
7.12
181
18
8
REGULAR PORT
3/4
1
1-1/2
20
25
40
5.5
6.62
8.7
140
168
220
2.06
2.12
3.4
52
54
86
4.62
5.69
9.06
117
145
230
9.12
11.19
16
232
284
406
3.8
4.62
6
97
117
152
7.12
8.5
11.5
181
216
292
18
30
73
8
14
33
2
50
10
254
3.4
86
10.88
276
18.5
470
6.86
174
15
381
106
48
1
25
5.5
140
2.06
52
4.62
117
9.12
232
3.8
97
7.12
181
18
8
REDUCED PORT
1-1/2*
2
40
50
6.62
8.7
168
220
2.12
3.4
54
86
5.69
9.06
145
230
11.19
16
284
406
4.62
6
117
152
8.5
11.5
216
292
30
73
14
33
2-1/2
65
10
254
3.4
86
10.88
276
18.5
470
6.86
174
15
381
106
48
E6
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Construction and materials for nuclear valves may vary depending upon customer design specifications. For a complete,
accurate, and itemized description of a particular valve, contact your Edward Valves sales representative.
DESCRIPTION
ASME/ASTM NO.
Body
ASME/ASTM NO.
SA-105
Disk
A-732
Body Seat
SA-182
Grade 21
Grade F316
A-732
Stellite 21
Grade 21
Stellite 21
Stem
A-582
T-416
Junk Ring
A-582
T-416
A-582
SA-564
Bonnet
SA-696
Grade C
SA-479
T316
Yoke Bolt
A-193
Grade B6
A-564
T-630
Packing
Gland
A-582
Retaining Ring
A-193
A-696
Grade C
Drive Pin
Key
A-564
Diaphragm Assembly
Diaphragm Disk
Shims
Disk Collar
Spring
Handwheel
Handwheel Nut
Indicator
Thrust Bearing
Lube Fitting
A-582
A-696
A-732
Grade 21
A-167
A-565
T-316
Grade 616
Inconel X-750
Malleable or
Ductile Iron
T-316
T630
Grade C
A-194
A-216
Nickel Plated
Grade 8
B-150
T630
T-416
SA-696 Grade C
B-670
A-564
T630
Spring Housing
Diaphragm Ring
Nickel Plated
T-630
Grade 6F
B-150
A-564
Grade B6
A-194
A-216
T-416
A-564
T-630
SA-479
T-316
B-670
A-732
Grade 21
A-167
A-565
T-316
Grade 616
Inconel X-750
Malleable or
Ductile Iron
T-316
Steel
Steel
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
E7
Edward Valves
7.
8.
9.
1.
10.
2.
3.
11.
12.
4.
5.
6.
2. Yoke bushing material has low coefficient of friction which substantially reduces torque and stem
wear and eliminates galling. Mechanical upset locks
yoke bushing to yoke.
E8
8. Threaded bonnet has ACME threads for resistance to galling and ease of disassembly. Unwelded
models utilize a graphitic gasket for dependable
sealing. Welded models employ a fillet weld (canopy
weld on stainless steel valves) for absolute protection from body-bonnet leakage.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
OS & Y.
Y-Pattern.
Body-guided investment cast
Stellite disk.
Integral Stellite seat.
Integral backseat.
Asbestos free graphitic packing.
Parts shown are not applicable to all Univalve valves. Construction and materials for nuclear valves may vary depending
upon customer design specifications. For a complete, accurate, and itemized description of
a particular valve, contact your local Edward Valves sales representative.
DESCRIPTION
Body
Bonnet
Stem
2
Disk Size 1/2
4
Disk Size 2-1/2
Body Seat
ASME/ASTM NO.
SA-105
Grade F316
SA-696
SA-479
SA-182
Grade C
T-316
A-582
SA-564
T-416
T-630
Condition H-1100
A-732
A-732
Grade 21
Grade 21
SA-182 F316
SA-182 F316
Stellite Faced
Stellite Faced
Stellite 21
Stellite 21
A-732
Grade 21
Junk Ring
Packing Rings
ASME/ASTM NO.
A-182
A-732
Grade F6a
Grade 21
A-582
A-564
T-416
T-630
Yoke
A-181
A-181
Gland
Yoke Bushing
Yoke Bolt
Yoke Bolt Nut
Handwheel
Impactor Handle
Stem Nut
Class 70
Class 70
B150 C61900/62300
B150 C61900/62300
A-307
A-564
Grade A-Plated
T-630
A-563
A-194
Grade A-Plated
Grade 8
Malleable or
Malleable or
Ductile Iron
Ductile Iron
Mild Steel
Mild Steel
Plated
Plated
Adapter
Malleable or
Malleable or
Ductile Iron
Ductile Iron
Washer
Mild Steel
Mild Steel
Plated
Plated
Graphite
Graphite
Cast Steel
Cast Steel
A-313
A-313
T-302
T-302
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
E9
Edward Valves
1.
2.
3.
6.
4.
7.
8.
9.
5.
E10
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
This is not a complete list. Construction and materials will vary between sizes and pressure classes and may be changed without notice.
For a complete, accurate, and itemized description of a particular valve, contact your Edward Valves sales representative.
DESCRIPTION
BOLTED BONNET
ASME/ASTM NO.
Body/Bonnet
SA-105
Disk*
AISI 615
Stainless Steel
Body Seat
Stellite 21
Stem
A-582
Capscrews
SA-193
T-416
Grade B-7
Gasket
Spiral Wound
Packing
Non Asbestos
Gland
A-536
Grade 80 - 55 - 06
Yoke Bushing
Handwheel/Handle
Stem Nut
Eye Bolt
A-582
A-194
T-416
Grade 8
AISI
Grade 4140
Spring**
A-313
T-302
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
E11
Edward Valves
E12
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Edward gas-hydraulic actuator for large, fast-closing valves is subjected to seismic testing during rigorous
qualification program to provide dependability of operation under the most adverse conditions.
Standard Features
Stored energy (pressurized nitrogen)
integrally contained.
Hydraulic speed control system assures constant
valve stroking speed regardless of stem load.
Fail safe operation to either close or open valve
within an adjustable range of 3 to 10 seconds.
Self contained control system.
All safety related functional components are
duplicated for redundancy.
Exercise capability demonstrates operation of all
safety-related components.
Qualified to all applicable IEEE requirements.
All Actuators equipped with Edward IEEE
qualified AC or DC operated hydraulic
solenoid valves.
UNITS
lb.
kN
in.
mm
lb.
kg
sec.
A-100
21,000
93
6.5
165
720
325
A-180
63,000
293
12
305
1720
780
A-230
A-260
90,000
130,000
400
578
14
17.5
356
446
2270
2950
1030
1340
3 10 SECONDS (ADJUSTABLE)
A-290
160,000
712
20.5
521
3940
1790
A-330
205,000
912
24
610
5260
2390
NOTE: VALUES TABULATED ARE NOMINAL. FOR SPECIAL APPLICATIONS, OTHERWISE STANDARD ACTUATORS MAY BE MODIFIED FOR SHORTER OR LONGER TRAVEL
WITH CORRESPONDING EFFECTS ON WEIGHT. ENVIRONMENTAL TEMPERATURE RANGE OF THE APPLICATION WILL INFLUENCE THRUST.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
E13
Edward Valves
Standard Features
Minimizes water hammer effects on
postulated feedwater line break.
Computerized modeling verified by
dynamic testing.
The Edward Controlled Closure Check Valve was developed and qualified to serve a function that no other previous check valve
could handle. If a feedwater line should rupture in a nuclear power plant, the reversed flow from the reactor or steam generator out
of the containment boundary must be contained. Conventional check valves would close rapidly, but not fast enough to prevent
high reverse flow velocity; closure of the conventional valve would produce severe pressure surges due to water hammer possibly severe enough to produce rupture of other piping or equipment.
The Controlled Closure Check Valve is much like a Flite-Flow piston lift check valve, but it has an integral dashpot a plate with
a close-clearance fit around the rod connecting the disk and piston. Flow paths sized for individual applications limit the flow out of
the dashpot and consequently control the valve closing speed. See pg. G-17/G-19 for a discussion of water hammer and a comparison of the controlled closure check valve with other types.
E14
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
EV100
5th Edition
Accessories/Actuators
Edward Valves
Accessories
A
GLOBE, ANGLE, GATE
Unless otherwise specified when globe and angle valves are ordered with by-pass attached, the by-pass is attached to the left hand side of the valve
when viewed from the overseat end.
D
Edward Forged Steel Valves for use as by-passes
SOCKET WELDING ENDS ONLY
CLASS 600
CLASS 900
CLASS 1500
CLASS 2500
SERIES 4500
Fig. A848Y*
Fig. D36224
Fig. D36224
Fig. D66224
Fig. D96224
Fig. A868Y**
Fig. D36264
Fig. D36264
Fig. D66264
Fig. D96264
* ALL MOTOR ACTUATED BY-PASS VALVES WILL BE FURNISHED WITH FIG. D36224.
** ALL MOTOR ACTUATED BY-PASS VALVES WILL BE FURNISHED WITH FIG. D36264.
4
1/2
5
3/4
6
3/4
8
3/4
10 to 24
1
* By-passes are provided only when specified. Standard sizes of by-pass valves are in accordance with the table above. Larger size by-pass valves will be furnished on special
order.
Floor Stands
Chain Wheels
Valve Extension
Edward floor stands are cast iron or fabricated steel, and are designed and machined
for accurate alignment. They are regularly
furnished painted and are faced on bottom
and drilled. Two heights, 20 and 32 inches,
are available and can be furnished in indicating or non-indicating types. Spur and motor
control floor stands can be furnished to
meet special conditions.
A simple and efficient means of valve operation from a lower level is provided by the use
of chain wheels. They are fitted to the regular
valve handwheels and are furnished complete
with chain wheel and chain guide.
F2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Impactor Handwheel
Impactogear
Custom Paint
F
Flow
Automatic Center Cavity Equalizing Valve
(ACCEV)
Internal equalizer (DDI)
Drain or Vent
Internal Equalizer
All Edward Cast Steel Valves can be supplied with drains and/or vents. A standard
drain or vent pipe, six inches long, is socket
welded to the valve body, or as specified by
the customer.
External Equalizer
A pipe that connects the bonnet cavity of the
Equiwedge Gate Valve to the upstream side
of the valve. See drawing and page C-10 for
additional information.
Relief Valve
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
F3
Edward Valves
Leakoff
The left half of the schematic to the
right depicts a typical Leakoff
arrangement including lantern gland
and upper and lower packing sets.
This double packing arrangement
provides added protection against
packing leaks.
Live Loading
The right half of the schematic to the
right depicts a typical live loaded
packing assembly. The Belleville
springs provide a constant packing
load to compensate for packing consolidation and thermal effects.
Locking Devices
Edward Valves can be provided with
padlock & chain or other locking
devices as specified.
F4
Soft Seats
This option is available for both
Forged and Cast Steel Globe and
Check Valves on a limited basis.
The disk face can be fitted with a soft
seat or insert when drop tight sealing
is a must. However, some limitations
(temperature, differential pressure,
radiation) may apply. Consult your
Edward Valves representative for
more information.
Washout Connections
Edward Cast Steel Valves can be fitted
with special covers that incorporate a
pipe nipple to be used as a washout
connection to introduce cleaning solutions etc. for pipeline flushing.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Actuators
A
B
C
D
E
The most commonly used actuators are: electric, pneumatic, hydraulic, manual gear,
or a stored energy gas hydraulic used in nuclear applications. Most Edward valves
can be equipped with an actuator if required. Where specific or special customer
requirements are needed, Edward engineering and expertise with all types of actuators can be applied and adapted to meet the most rigid codes.
The following information on page F6 will allow Edward engineers to correctly size
and select the proper motor actuator for your application.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
F5
Edward Valves
1. OPERATING PRESSURES:
A) PRESSURE UNDER SEAT = _____________________________________ psig
B) PRESSURE OVER SEAT = _______________________________________ psig
C) PRESSURE DIFFERENTIAL = ____________________________________ psig
2. MOTOR POWER SUPPLY*:
A) AC = __________________V.____________________ HZ. ____________________ PH. ______________________
B) DC = __________________V.
*STANDARD VOLTAGE VARIANCE 10%, IF OTHERWISE, PLEASE INDICATE
Data in the Table above represents the minimum information that should be provided when ordering a valve equipped with a motor operator.
F6
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
EV100
5th Edition
Technical
Edward Valves
Table of Contents
Page No.
1.
1.1
1.1.1
1.1.2
1.1.3
1.1.4
1.1.5
4
4
4
7
7
8
9
10
10
13
1.3
1.4
1.4.1
1.4.2
1.4.3
1.4.4
2.
2.1
14
15
18
19
19
19
22
22
Flow Performance
Choose the Best Valve Size for
Your Service Conditions
2.1.1 Pressure Drop, Sizing and Flow Rate Calculations
Fully Open Valves All Types
23
2.2
2.2.1
2.2.2
2.2.3
2.2.4
23
24
24
25
25
Basic Calculations
Pressure Drop
Required Flow Coefficient
Flow Rate
Inlet Flow Velocity
Page No.
2.3
Corrections Required with Large Pressure Drops
2.3.1 Gas and Steam Flow
2.3.2 Liquid Flow Cavitation, Flashing and
Choking Corrections
26
26
2.4
Check Valve Sizing
2.4.1 Sizing Parameter
2.4.2 Calculations for Check Valves Less Than
Fully Open
2.4.3 Specific Sizing Guidelines
28
28
2.5
Pipe Reducer Coefficients
2.5.1 Pipe Geometry Factor
2.5.2 Other Coefficients
30
30
30
3.
3.1
3.2
3.3
3.4
3.5
59
59
59
60
61
61
4.
4.1
4.2
62
62
62
27
28
28
23
23
Equations and calculations outlined in this manual are available in a proprietary Edward Valves computer program.
Consult your Edward Valves sales representative for more information.
G2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
G14
G14
G15
G15
G15
G15
G15
G16
G20
G20
G21
G21
G26
G26
G40
G43
G46
G49
G52
G56
G56
G56
G57
G57
G57
G58
G30A
G31
G32
G33
G34
G35
G36
G37
G37
G38
G39
G41
G44
G47
G50
G53
G55
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G3
Edward Valves
Foreword
Edward stop valves are used primarily as isolation
valves in medium and high pressure piping systems.
They are offered in a broad range of sizes, pressure
ratings, and types, and they are used in an immense
array of diverse applications. Only a few are listed for
illustration:
Normally open valves in main steam lines; used
only for equipment isolation, e.g. during maintenance.
Normally open valves to provide for emergency
shutoff due to failure of downstream piping or other
equipment; closed periodically for verification of
operability.
Normally open valves that are throttled to varying
degrees during start-up or shutdown of plants or
systems.
Frequently cycled valves that are opened and
closed for control of batch processes or for start-up
and shutdown of equipment (e.g., equipment that is
on-stream daily but shut-down at night).
Normally closed valves; used only for filling or
draining systems during outages.
Edward stop valves are typically of metal-seated construction and, where necessary, use gaskets and stem
seals designed for severe high-pressure, high-temperature service. While special designs with soft
seats and O-ring seals are supplied for unique specific applications, the standard products are designed
to stand up to tough service conditions with minimum
requirements for maintenance or parts replacement.
Edward stop valves fall into two basic categories
globe valves and gate valves. The following sections of this guide will address the principal features of
each type and the design variations within the types.
Globe valves are offered in stop, stop-check, and
check versions. Stop-check valves can also be used
for isolation in unidirectional flow applications.
These valves are discussed in the Check Valves
Applications section (1.2).
The FLOW PERFORMANCE section of this catalog
provides equations and coefficients for the calculation
of pressure drop across any of these valves. This information can be used to evaluate the effects of different
valve sizes and types on system energy efficiency.
Brief notes on the advantages, disadvantages, applications and limitations of the various types of Edward
stop valves are presented in the Stop Valve
Applications Chart (section 1.1.4). Some additional
highlights of the features of these valves and some
comparisons with similar valves are presented in the
following paragraphs.
Globe Valves
A globe valve employs a poppet or disk that opens
and closes by moving linearly along the seat axis.
There are many types of globe valve bodies, seats
and methods of guiding the disk to and from the seat.
The goal of this guide is to supplement users experience with information based on decades of Edward
Valves laboratory tests and field experience.
Introduction
While many other types of valves (ball, plug, butterfly) are used as stop valves where service conditions
permit, emphasis in this guide is on selection and
application of Edward valves with forged- and caststeel bodies and bonnets. Comparisons are presented with other similar valves where appropriate.
G4
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G5
Edward Valves
G6
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Inherent Flow
Characteristics
Figure A provides typical inherent flow-characteristic curves (percent of full-open flow coefficient
versus percent opening) of the most common types
of Edward stop valves. It should be understood that
these curves are approximate, because there are
variations due to size and pressure class that cannot
be represented accurately by a single curve for each
valve type. Nevertheless, these typical curves can
provide some guidance relating to control capabilities of the various valve types.
Note the following subtle differences between the
curves in Figure A:
The conventional 90-bonnet globe valve provides a relatively steep slope at small openings
approaching a quick-opening characteristic. While
the body-guided disk in Edward globe valves moderates this effect, it makes the flow coefficient very
sensitive to small changes in stem position, so it
may prove difficult to control low flow rates.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G7
Edward Valves
Power Actuators
Where valves are inaccessible for manual operation
or where relatively fast opening or closing is
required, most Edward valves can be furnished with
power actuators. The most commonly used actuators
are electric actuators with torque- and position-control features. Users frequently have individual preferences on actuator brand names and type, so Edward
valves are furnished with Limitorque, Rotork, Auma
or other actuators to satisfy customer requirements.
Edward Valves establishes actuator sizes and switch
setting based on specific valve-application requirements, using a computer program that matches the
valve and actuator operating characteristics to the
service-pressure conditions. Unlike most valve manufacturers, Edward Valves makes this selectionnot
the actuator manufacturersince we best know the
requirements of our valve. However, we must also
know the requirements of your application. As a minimum, requests for quotation should specify:
Operating pressures under-and over-seat and
differential
Maximum valve operating temperature
Ambient conditions temperature, humidity,
radiation
Motor power supply AC voltage, frequency, and
phase or DC voltage (including variance)
NEMA rating
Closing/opening time if important. If not specified, standard nominal stem speed will be 4 inches/minute (100 mm/min) for globe valves and 12
inches/min (305 mm/min) for gate valves.
Valve-stem plane vertical (stem up or down) or
horizontal
Special accessories position indicator, etc.
Drain valves for all main valves are the same as the
by-pass valves listed for stop valves. When drains are
specified without valves, the standard drain for class
300 and 600 valves is a NPT tapped hole in the valve
body, fitted with a pipe plug. For class 900 and higher-pressure valves, the standard drain is a pipe nipple, six inches (152 mm) long, socket-welded to the
valve body.
Drain sizes are the same as by-passes. By-pass valves
are particularly useful when opened before the main
valve to permit controlled warming of the valve and
downstream line in services involving steam or other
hot fluids. By-passes also can be used to partially or
fully balance the differential pressure across the main
valve before opening where the downstream line or
system is of limited volume. This facilitates opening of
a gate valve or a glove valve with overseat pressure.
Large-volume systems may require larger by-passes for balancing in a reasonable time. If this is the
case, a special by-pass size should be specified by
the purchaser. It should be noted that actuated
Edward Equiwedge gate valves do not require bypasses to permit opening if the full differential pressure is specified for actuator sizing. See page F-2
for tables of standard sizes and pressure classes for
most applications.
G8
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
TYPE
Globe
90 Bonnet
ADVANTAGES
DISADVANTAGES
APPLICATIONS
LIMITATIONS
Compact
Easy access to
Handwheel or
Actuator
High torque
Same as Globe
High torque
Same as Globe
Same as Globe
Replaces an Elbow
Same as Globe
Fast response
Angle
Same as Angle
Longest end-to-end
length
Handwheel or
Actuator
on an Angle
Otherwise, same as
Globe
Not recommended
for throttling
Possibility of
pressure binding
Lowest torque
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G9
Edward Valves
G10
Introduction
This guide has been prepared to aid fluid-system
designers in sizing and selecting check valves for
industrial and power-piping systems. Guidance is
also provided on valve orientation (inclination from
horizontal, etc.) and on location of check valves with
respect to other flow disturbances. In addition, this
guide should aid users in planning preventive maintenance programs, performing maintenance and
repairs when necessary, and in evaluating and correcting problems.
Finally, this guide addresses check valve maintenance. History indicates that preventive maintenance
of check valves is often neglected, and this can lead
to serious valve failures which may damage other
equipment. The guidelines provided on periodic
inspection and preventive maintenance should pay
off in terms of reduced overall plant maintenance and
repair costs.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G11
Edward Valves
G12
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
TYPE
Piston Lift Check
Ball Check
Stop-Check
ADVANTAGES
DISADVANTAGES
APPLICATIONS
LIMITATIONS
Class 3004500
service.
High temperature steam
and water.
Refining, petrochemical,
chemical, etc.
Oilfield production.
Can be used in series with
Tilting Disk Check to provide maximum
line protection (advantages
of both types).
Class 6004500
service.
High temperature steam
and water.
Refining, petrochemical,
chemical, etc.
Oilfield production.
Can be used in series with
Piston Lift Check or StopCheck to provide
maximum line protection
(advantages of both types).
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G13
Edward Valves
Edward cast-steel Flite-Flow, forged-steel Univalve, and inclined-bonnet check and stop-check
valves without springs, when installed in vertical or
near vertical lines, should be oriented such that the
fluid flow is upward and the angle of incline of the
line is not more than 5 past the vertical in the direction of the bonnet. When installed in horizontal or
near horizontal lines, the valve bonnet should be up
and the angle of incline of the line should be not more
than 5 below the horizontal. See Figure 1A. Also, the
roll angle of the valve bonnet should not be more than
20 from side to side for either vertical or horizontal
installations. See Figures 1B and 1C. Consult your
Edward Valves representative concerning installation
limits of bolted-bonnet forged-steel check valves
without springs.
Edward cast-steel and forge-steel 90-bonnet
check and stop-check valves without springs should
be installed with the bonnet up, and the angle of
incline of the line should not be more than 45 form
the horizontal. Also, the roll angle of the valve bonnet
should not be more than 45 from side to side. See
Figures 2A and 2B.
Figure 2
90 Bonnet Piston Lift Check Valves
Maximum Valve Orientation Limits
Note: For piston lift check valves, any installation resulting in combined out of position orientation, such as
a valve in an inclined line with a rollover angle as well, should limit the angle of the bonnet to the following:
45 from vertical for angle and 90bonnet valves.
50 from vertical for inclined bonnet valves.
Unlike stop valves, which can be installed in any
position with little or no effect on performance, most
check and stop-check valves have limitations as to
their installed orientation. Although the normal
installation is in a horizontal or vertical line (depending on valve type), check and stop-check valves can
be installed in other orientations. It should be noted,
however, that valves installed in other than the normal
positions may exhibit a degradation of performance,
service life and resistance to sticking, depending on
the flow conditions and cleanliness of the line fluid.
For maximum reliability, it is recommended that piston-lift check valves and stop-check valves be
installed with flow axis horizontal (vertical inlet and
horizontal outlet for angle valves) with the bonnet
above the valve in a vertical plane. Following are
G14
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Figure 4
Tilting Disk Check Valves
Orientation Limits
Figure 6
Non-uniform velocity profile at blower or pump
discharge can affect stability.
Figure 5
Pipe fittings near valves may produce
instability because of velocity profile distortion
Figure 7
Elbows in two places cause swirl which can promote instability.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G15
Edward Valves
Figure 8
Size 4 Class 600 90 bonnet piston lift check valve
with two upstream elbows (out of plane). This
arrangement produces swirl as shown in Figure 7.
Figure 9
Size 10 Class 1500 Flite-Flow inclined bonnet piston lift check valve with two upstream elbows. Test
loop capacity permitted tests with line velocity over
20 ft./sec. (6 m/sec.).
In most tests, room temperature water was the flow
medium, but limited straight-pipe testing was performed with air. The valves tested included Edward
piston-lift check (inclined-bonnet, angle and 90bonnet), tilting-disk check valves and a size-4 swing
check valve manufactured by another company. The
tests were designed to evaluate the effects of flow disturbances on (1) valve stability, particularly when partially open; (2) flow rate required to open the valve
fully; and (3) the flow coefficient (CV) of the valve. The
flow disturbances evaluated included single and double (out of plane) 90 elbows in various orientations
immediately upstream of the check valves. In addi-
G16
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
opening should be assured. Valves operating at partial opening for significant periods of time should be
monitored regularly to determine if there is insta
bility or wear.
In view of uncertainties associated with longterm effects of flow disturbances, it is recommended that a minimum of 10 diameters of straight pipe
be provided between the inlet of a check valve and
any upstream flow disturbance (fittings, pumps,
control valves, etc.), particularly if calculations
indicate that the check valve will not be fully open
for a substantial portion of the valve service life.
There should be a minimum of 1 to 2 diameters of
pipe between the check valve and the nearest downstream flow disturbance.
In the specific case of upstream elbows, reasonably
successful performance should be attainable with 5
diameters of straight pipe between an upstream elbow
and a check valve if the valve will not be partially
open for a significant portion of its service life. Tests
described in EPRI Report No. NP 5479 indicate that
elbows installed 5 diameters or more upstream had a
negligible effect on swing check valves, and this is
expected to be true for other check valve types. Even
less straight pipe may be satisfactory, but such close
spacing should be reserved for applications with very
tight space constraints. More frequent inspection and
VALVE
SIZE & TYPE
SINGLE ELBOW1
AT VALVE INLET
Size 2, Inclined-Bonnet
Piston-Lift Check
NA
NA
NA
Size 4, Angle
Piston-Lift Check
No Effect
No Effect
NA
NA
NA
Size 4, 90-Bonnet
Piston-Lift Check
No Effect
NA
NA
NA
NA
Size 8, Angle
Piston-Lift Check
No Effect
NA
NA
NA
NA
Size 8, 90-Bonnet
Piston-Lift Check
NA
NA
NA
NA
No Effect
Failure to Achieve
Full Open;
Disk Flutter and Chatter
Failure to Achieve
Full Open
No Effect
No Effect
Minor Flutter
Minor Flutter
No Effect
1Tests
2One
were conducted with single 90 elbows in the horizontal plane and in the vertical plane (with flow both from above and below).
size-2 valve exhibited flutter at lower lifts; another was stable.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G17
Edward Valves
G18
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G19
Edward Valves
normal
flow
direction
G20
Dashpot Chamber
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Figure 13
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G21
Edward Valves
G22
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
2. Flow Performance
2.1 Choose the Best Valve Size for
Your Service Conditions
The most economical valve is the valve correctly
sized for the service flow conditions. Too small a
valve will have a high pressure drop and will incur
expensive energy costs in service. Too large a valve
wastes money at the time of purchase, and it may
require excessive effort or an excessively large and
expensive actuator for operation.
Piping-system designers sometimes optimize the
size of valves and piping systems to minimize the
sum of investment costs and the present value of
pumping power costs. While this may not be practical for selection of every valve, it is a goal that
should be kept in mind. This catalog provides information necessary to evaluate the various types and
sizes of Edward valves for stop (isolation), stopcheck and check valve applications.
In the case of stop-check and check valves, another
consideration is that an oversized valve may not
open completely. Obviously, if a valve is not fully
open, the pressure drop will be increased. Also, if
the disk operates too close to the seat, unsteady flow
may cause flutter that may damage valve seats, disks
or guides.
System designers should also address turndown if
service conditions involve a broad range of flow
rates (e.g., high flow in normal operation but low
flow during start-up and standby conditions). For
these reasons, selection of check valves requires
extra steps and care in calculations.
This section includes equations for the calculation of
pressure drop, required flow coefficient, flow rate or
inlet flow velocity. Procedures are also provided to
check and correct for cavitation and flow choking.
The equations in this section assume that the fluid is
a liquid, a gas or steam. Two-component flow (e.g.
slurries, oil-gas mixtures) is not covered by the
equations. Consult Edward Valves for assistance in
evaluating such applications.
Tables in this section contain performance data for
all Edward stop, stop-check and check valves. Flow
coefficients and cavitation/choked-flow coefficients
are given for all fully open Edward valves. In addition, for check and stop-check valves, the tables
provide minimum pressure drop for full lift, crackopen pressure drop, and a novel sizing parameter
that is helpful in selecting the proper valve size for
each application.
G
Note: In preliminary calculations using the following equations, a piping geometry factor, Fp =
1.0, may be used, assuming that the valve size is the same as the nominal pipe size. However, if an
application involves installing a valve in a larger-sized piping system (or piping with a lower pressure rating than the valve, which will have a larger inside diameter), determine Fp from the Pipe
Reducer Coefficients section when final calculations are made.
Equations and calculations outlined in this manual are available in a proprietary Edward Valves computer program.
Consult your Edward Valves sales representative for more information.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G23
Edward Valves
Flow rate (w or q)
Fluid specific gravity (G) or
Density ()
For water, steam or air, see
Figures 22-24
FIND:
CALCULATE:
When flow rate and fluid properties are known, determine required coefficients for a specific valve and calculate the pressure drop from the appropriate equation (see Nomenclature table for definition of terms
and symbols):
q
P = G
(F C )
P = G
(0.865F C )
(U.S.)(1a)
P V
(metric)(1b)
P V
P =
1
w
63.3F PC V
P =
1
w
27.3FPC V
(
(
(U.S.)(1c)
(metric)(1d)
Nomenclature
(Metric units in parentheses)
CV
FL
Fp
GV
Rp
R1
R2
SP
Ki
xT
p1
pV
G24
RF
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Flow rate (w or q)
Fluid specific gravity (G) or
Density ()
For water, steam or air, see
Figures 22-24
FIND:
CALCULATE:
0.409q
d2
V=
354q
d2
V=
0.0509w
d2
V=
354w
d2
(U.S.)(4a)
(metric)(4b)
(U.S.)(4c)
(metric)(4d)
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G25
Edward Valves
P
R1 =
p1
(5)
Figure 14
( )
G y = 0.467 P
kxT p1
(U.S. or metric)(6)
Note: The P in this equation is the uncorrected value from the Basic Calculations.
Values of xT are given in valve data tables,
and values of k are given in Figure 21.
Max. P/p1
Gate
0.01
Inclined-Bonnet Globe
Angle
Tilting-Disk Check
0.02
90-Bonnet Globe
0.05
Figure 15
G26
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
( )
Y= 1 0.467
(U.S. or metric)(11)
P
(p1pv)
(12)
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G27
Edward Valves
(U.S. or metric)(16)
G28
RF =
SP
SPFL
(U.S. or metric)(17)
(U.S. or metric)(18)
Values for PFL for all stop-check and check valves are
given in Valve Tables 1 to 5 and 10 to 15 with other
coefficients.
Note: The values of the various valve coefficients given in the tabulations are based on
testing of a substantial number of valves. Most
are applicable to any line fluid, but those
involving check valve lift are influenced by
buoyancy. Tabulated values are based on reference test conditions with room-temperature
water. SPFL and PFL are slightly higher in
applications involving lower-density line fluids. Considering the expected accuracy of
these calculations, the following corrections
may be considered:
For water at any temperature and other common liquids No correction required.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Disk Skirt
normal
flow
direction
Figure 15A
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G29
Edward Valves
This method is also applicable when valves are furnished with oversized ends to fit larger diameter pipe.
It should also be used to evaluate line-size valves
used in pipe with a lower pressure rating than the
valve, because such pipe may have less wall thickness and a larger inside diameter than the valve inlet
diameter given in the valve data tabulations.
This section provides equations for calculation of the
piping geometry factor, Fp, which should be used
even in Basic Calculations when there is a significant
difference between the pipe diameter and valve inlet
diameter (d).
In addition, other coefficients (K1, FL, xT) are affected
by the presence of pipe reducers. Equations are also
provided for correction of these terms, which are
required only when evaluating significant valve-topipe diameter mismatch.
Note: These equations apply only where the
valve diameter is less than the connecting
pipe diameter.
Nomenclature
CV =
K1 =
d=
K2 =
D1 =
D2 =
K = K1 + K2, dimensionless
FL =
Fp =
Ki =
incipient-cavitation coefficient,
dimensionless*
xT =
* Double subscripts (e.g., Kii) represent values corrected for effects of pipe reducers.
G30
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 1
Forged Steel Angle Univalve Flow Coefficients
CHECK VALVES*
WITH SPRINGS (STD)
CV
FL
xT
Ki
PFL
SPFL
CHECK VALVES*
WITHOUT SPRINGS
PFL
SPFL
Class 1690 (PN 290) All Stop valves, all Stop-Check valves, all Piston Check valves
0.50
15
10.5
0.68
17.3
887
101
179
468
53
165
0.75
20
10.5
0.68
17.3
1522
172
179
804
91
165
1.00
25
10.5
0.68
17.3
1522
172
179
804
91
165
1.25
32
31
1.19
30.2
5326
604
179
2810
318
164
1.50
40
31
1.19
30.2
5066
574
179
2670
303
164
2.00
50
50
1.50
38.1
8620
977
180
4550
516
166
2.50
65
90
2.00
50.8
13,916
1580
179
7360
834
165
3.00
80
90
2.00
50.8
12,715
1440
179
6690
758
165
0.80
0.41
0.16
6.0
0.41
1.5
0.103
Class 2680 (PN 460) All Stop valves, all Stop-Check valves, all Piston Check valves
0.50
15
10.5
0.68
17.3
729
83
179
385
44
165
0.75
20
10.5
0.68
17.3
625
71
179
330
37
165
1.00
25
10.5
0.68
17.3
1140
129
179
604
68
165
1.25
32
19
0.94
23.9
3120
354
177
1650
187
163
1.50
40
19
0.94
23.9
2910
330
177
1540
175
163
2.00
50
50
1.50
38.1
7290
826
180
3850
436
166
2.50
65
89
2.00
50.8
10,400
1180
179
5490
622
165
3.00
80
89
2.00
50.8
10,400
1180
179
5490
622
165
NOTES:
0.80
0.41
0.16
6.0
0.41
1.5
0.103
G
G
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G30A
Edward Valves
Table 1A
Forged Steel Univalve Flow Coefficients
CHECK VALVES*
WITH SPRINGS (STD)
CV
FL
xT
Ki
PFL
SPFL
CHECK VALVES*
WITHOUT SPRINGS
PFL
SPFL
Class 1690 (PN 290) All Stop valves, all Stop-Check valves, all Piston Check valves
0.50
15
7.0
0.464
11.8
886
100
210
443
50.2
105
0.75
20
12
0.612
15.5
1520
172
207
760
86.0
103
1.00
25
12
0.815
20.7
1520
172
117
760
86.0
58
1.25
32
42
1.160
29.5
5320
602
201
2660
301
101
1.50
40
40
1.338
34.0
5060
574
144
2530
287
72
2.00
50
68
1.687
42.8
8610
975
154
4300
488
77
2.50
65
110
2.125
54.0
13,900
1580
157
6960
789
79
3.00
80
100
2.624
66.6
12,700
1430
94
6330
717
47
4.00
100
85
3.438
87.3
10,800
1220
46
5380
609
23
0.66
0.27
0.16
4.0
0.28
1.0
0.069
Class 2680 (PN 460) All Stop valves, all Stop-Check valves, all Piston Check valves
0.50
15
7.0
0.464
11.8
886
100
210
443
50.2
105
0.75
20
12
0.612
15.5
760
86.0
103
380
43.0
52
1.00
25
11
0.599
15.2
1390
158
198
696
78.9
99
1.25
32
30
0.896
22.8
3800
430
241
1900
215
121
1.50
40
28
1.100
28.0
3540
401
149
1770
201
75
2.00
50
70
1.503
38.2
8860
1000
200
4430
502
100
2.50
65
100
1.771
45.0
12,700
1430
206
6330
717
103
3.00
80
100
2.300
58.4
12,700
1430
122
6330
717
61
4.00
100
90
3.152
80.1
11,400
1290
58
5700
645
29
0.63
0.24
0.15
4.0
0.28
1.0
0.069
Class 4500 (PN760) All Stop valves, all Stop-Check valves, all Piston Check valves
0.50
15
2.0
0.252
6.4
253
28.7
203
127
14.3
102
0.75
20
6.0
0.434
11.0
760
86.0
205
380
43.0
103
1.00
25
12
0.599
15.2
1520
172
216
760
86.0
108
1.25
32
12
0.808
20.5
1520
172
117
760
86.0
59
1.50
40
11
0.926
23.5
1390
158
82
696
78.9
41
2.00
50
48
1.156
29.4
6080
688
230
3040
344
115
2.50
65
62
1.400
35.6
7850
889
202
3920
444
101
3.00
80
60
1.700
43.2
7600
860
132
3800
430
66
4.00
100
55
2.200
55.9
6960
789
76
3480
394
37
0.64
0.25
0.15
4.0
0.28
1.0
0.069
NOTES:
G31
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 1B
Forged Steel PressurCombo Flow Coefficients
PRESSURSEAT (DS)
DN
CV
FL
xT
PRESSUREATER (DE)
Ki
CV
FL
xT
PRESSURCOMBO (DC)
Ki
CV
FL
xT
Ki
15
5.0
0.464
11.8
5.0
0.464
11.8
4.1
0.464
11.8
0.75
20
6.1
0.612
15.5
5.9
0.612
15.5
4.5
0.612
15.5
1.00
25
6.1
0.815
20.7
5.6
0.815
20.7
4.4
0.815
20.7
1.25
32
12
1.160
29.55
11
1.160
29.5
8.0
1.160
29.5
1.50
40
12
1.338
34.0
11
1.338
34.0
8.0
2.00
50
30
1.687
42.3
28
1.687
42.8
22
.85
.50
.27
.80
.45
.24
.80
.45
.24
1.338
34.0
1.687
42.8
2.50
65
53
2.125
54.0
51
2.125
54.0
39
2.125
54.0
3.00
80
51
2.624
66.6
47
2.624
66.6
37
2.624
66.6
4.00
100
49
3.438
87.3
43
3.438
87.3
35
3.438
87.3
15
5.0
0.464
11.8
5.0
0.464
5.0
4.1
0.464
11.8
0.75
20
4.6
0.612
15.5
4.5
0.612
4.5
3.8
0.612
15.5
1.00
25
6.0
0.599
15.2
5.7
0.599
5.7
4.5
0.599
15.2
1.25
32
12
0.896
22.8
12
0.896
12
8.9
0.896
22.8
1.50
40
12
1.100
28.0
11
1.100
11
8.3
2.00
50
31
1.502
38.2
30
1.502
30
23
.85
.50
.27
.80
.45
.24
.80
.45
.24
1.100
27.9
1.502
38.2
2.50
65
52
1.771
45.0
56
1.771
56
41
1.771
45.0
3.00
80
52
2.300
58.4
48
2.300
48
38
2.300
58.4
4.00
100
50
3.152
80.1
44
3.152
44
36
3.152
80.1
15
1.9
0.252
6.4
1.5
0.252
6.4
1.4
0.252
6.4
0.75
20
4.6
0.434
11.0
4.4
0.434
11.0
3.8
0.434
11.0
1.00
25
6.1
0.599
15.2
5.8
0.599
15.2
4.5
0.599
15.2
1.25
32
6.1
0.808
20.5
5.6
0.808
20.5
4.4
0.808
20.5
1.50
40
5.9
0.926
23.5
5.3
0.926
23.5
4.3
2.00
50
28
1.156
29.4
29
1.156
29.4
22
.85
.50
.27
.80
.45
.24
.80
.45
.24
0.926
23.5
1.158
29.4
2.50
65
30
1.400
35.6
30
1.400
35.6
23
1.400
35.6
3.00
80
30
1.700
43.2
28
1.700
43.2
22
1.700
43.2
4.00
100
29
2.200
55.9
25
2.200
55.9
21
2.200
55.9
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G32
Edward Valves
Table 2
Forged Steel Inclined Bonnet Valve Flow Coefficients
CHECK VALVES*
WITH SPRINGS (STD)
CV
FL
xT
Ki
PFL
SPFL
CHECK VALVES*
WITHOUT SPRINGS
PFL
SPFL
Class 800 (PN 130) Figure No. 848/848Y Stop valve, 868/868Y Stop-Check valve, 838/838Y Piston Check valve
0.25
1.4
0.364
9.2
198
22.4
76
68.6
7.77
26
0.38
10
3.3
0.493
12.5
467
52.9
98
162
18.3
34
0.50
15
3.3
0.546
13.9
467
52.9
80
162
18.3
28
0.75
20
5.7
0.742
18.8
722
81.8
67
250
28.3
23
1.00
25
13.5
0.957
24.3
1910
216
106
662
75.0
37
1.25
32
23.5
1.278
32.5
3330
377
104
1150
131
36
1.50
40
37.5
1.500
38.1
5290
600
120
1830
208
42
2.00
50
48.5
1.939
49.3
6860
778
93
2380
269
32
0.72
0.30
0.20
5.0
0.34
0.6
0.041
Series 1500 Figure No. 1048/1048Y Stop valve, 1068/1068Y Stop-Check valve, 1038/1038Y Piston Check valve
0.25
1.7
0.302
7.7
241
27.3
134
83.4
9.45
47
0.38
10
3.9
0.423
10.7
552
62.5
157
191
21.7
54
0.50
15
3.8
0.464
11.8
538
60.9
127
186
21.1
44
0.75
20
6.8
0.612
15.5
963
109
131
333
37.8
45
1.00
25
10.5
0.815
20.7
1490
168
114
515
58.3
39
1.25
32
28
1.160
29.5
3960
449
150
1370
155
52
1.50
40
26.5
1.338
34.0
3750
425
107
1300
147
37
2.00
50
41.5
1.687
42.8
5870
665
105
2030
230
36
0.75
0.34
0.20
5.0
0.34
0.6
0.041
NOTES:
G33
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 3
Forged Steel Angle Valve Flow Coefficients
CHECK VALVES*
WITH SPRINGS (STD)
CV
FL
xT
Ki
PFL
SPFL
CHECK VALVES*
WITHOUT SPRINGS
PFL
SPFL
Class 600 (PN 110) Figure No. 829 Stop valves, 847 Stop-Check valves
0.50
15
3.3
0.546
13.9
512
58.0
87
187
21.2
32
0.75
20
5.7
0.742
18.8
884
100
82
323
36.5
30
1.00
25
17.5
0.957
24.3
2710
307
151
991
112
55
1.25
32
36
1.278
32.5
5580
632
174
2040
231
64
1.50
40
35
1.500
38.1
5430
615
123
1980
224
45
2.00
50
45.5
1.939
49.3
7050
799
96
2580
292
35
0.55
0.19
0.11
6.0
0.41
0.8
0.055
Class 800 (PN 130) Figure No. 849/849Y Stop valves, 869/869Y Stop-Check valves
0.25
2.6
0.364
9.2
403
45.7
155
147
16.7
57
0.38
10
2.9
0.493
12.5
450
50.9
94
164
18.6
34
0.50
15
2.8
0.546
13.9
434
49.2
74
159
18.0
27
0.75
20
4.8
0.742
18.8
744
84.3
69
272
30.8
25
1.00
25
10.5
0.957
24.3
1630
184
91
595
67.3
33
1.25
32
31
1.278
32.5
4810
544
150
1760
199
55
1.50
40
30
1.500
38.1
4650
527
105
1700
192
38
2.00
50
38.5
1.939
49.3
5970
676
81
2180
247
30
0.64
0.25
0.16
6.0
0.41
0.8
0.055
Series 1500 Figure No. 1049/1049Y Stop valves, 1069/1069Y Stop-Check valves
0.25
1.9
0.302
7.7
295
33.4
165
108
12.2
60
0.38
10
2.9
0.423
10.7
450
50.9
128
164
18.6
47
0.50
15
2.9
0.464
11.8
450
50.9
106
164
18.6
39
0.75
20
5.0
0.612
15.5
775
87.8
105
283
32.1
39
1.00
25
7.7
0.815
20.7
1190
135
92
436
49.4
33
1.25
32
20
1.160
29.5
3100
351
117
1130
128
43
1.50
40
20
1.338
34.0
3100
351
88
1130
128
32
2.00
50
33.5
1.687
42.8
5190
588
93
1900
215
34
0.61
0.22
0.14
6.0
0.41
0.8
0.055
Series 1500 Figure No. 1029 Stop valves, 1047 Stop-Check valves
0.50
15
2.7
0.464
11.8
419
47.4
99
153
17.3
36
0.75
20
4.7
0.612
15.5
729
82.5
99
266
30.1
36
1.00
25
7.5
0.815
20.7
1160
132
89
425
48.1
33
1.25
32
21
1.160
29.5
3260
369
123
1190
135
45
1.50
40
21
1.338
34.0
3260
369
93
1190
135
34
2.00
50
31.5
1.687
42.8
4920
557
88
1790
203
32
NOTES:
0.65
0.24
0.16
6.0
0.41
0.8
0.055
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G34
Edward Valves
Table 4
Edward Forged Steel Vertical Stem Globe Valve &
90 Bonnet Piston Check Valve Flow Coefficients
CHECK VALVES*
WITH SPRINGS (STD)
CV
FL
xT
Ki
PFL
SPFL
CHECK VALVES*
WITHOUT SPRINGS
PFL
SPFL
Series 600 (PN 110) Figure No. 828 Stop valve, 846 Stop-Check valve, 858 Piston Check valve
0.50
15
2.4
0.546
13.9
430
48.7
73
166
18.8
28
0.75
20
4.2
0.742
18.8
752
85.2
70
291
33.0
27
1.00
25
13.5
0.957
24.3
2400
272
133
929
105
52
1.25
32
27.5
1.278
32.5
4920
558
154
1910
216
59
1.50
40
27
1.500
38.1
4830
548
109
1870
212
42
2.00
50
35.5
1.939
49.3
6360
720
86
2460
279
33
0.63
0.29
0.15
8.0
0.55
1.2
0.083
Series 1500 Figure No. 1028 Stop valve, 1046 Stop-Check valve, 1058 Piston Check valve
0.50
15
3.6
0.464
11.8
645
73.0
153
250
28.3
59
0.75
20
6.2
0.612
15.5
1110
126
151
430
48.7
58
1.00
25
6.2
0.815
20.7
1110
126
85
430
48.7
33
1.25
32
18
1.160
29.5
3220
365
122
1250
141
47
1.50
40
17.5
1.338
34.0
3130
355
89
1210
137
35
2.00
50
24.5
1.687
42.8
4390
497
79
1700
192
30
0.68
0.27
0.17
8.0
0.55
1.2
0.083
NOTES:
G35
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 5
Forged Steel Ball Check Valve Flow Coefficients
CHECK VALVES
WITH SPRINGS (STD)
CV
FL
xT
Ki
PFL
SPFL
Class 800 (PN 130) Figure No. 832/832Y Ball Check valve
0.25
1.5
0.364
9.2
233
26.3
89
0.38
10
3.5
0.493
12.5
543
61.5
114
0.50
15
3.5
0.546
13.9
543
61.5
93
0.75
20
6.1
0.742
18.8
946
107
88
1.00
25
14
0.957
24.3
2170
246
121
1.25
32
25
1.278
32.5
3880
439
121
1.50
40
39.5
1.500
38.1
6120
694
139
2.00
50
51.5
1.939
49.3
7990
904
108
0.53
0.16
0.11
6.0
0.41
1.1
0.302
7.7
171
19.3
95
0.38
10
2.5
0.423
10.7
388
43.9
110
0.50
15
2.4
0.464
11.8
372
42.1
88
0.75
20
4.3
0.612
15.5
667
75.5
91
1.00
25
6.6
0.815
20.7
1020
116
79
1.25
32
17.5
1.160
29.5
2710
307
103
1.50
40
17
1.338
34.0
2640
299
75
2.00
50
26.5
1.687
42.8
4110
465
74
1.502
38.2
3960
449
89
0.77
0.37
0.16
6.0
0.41
5000 CWP (345 Bar) Figure No. 5160 Hydraulic Check valve
2.00
50
14
0.96
0.57
0.24
20
1.4
10000 CWP (690 Bar) Figure No. 160/160Y Hydraulic Check valve, 9160 Hydraulic Check valve
0.25
0.40
0.133
3.4
113
12.8
326
0.38
10
0.80
0.205
5.2
227
25.7
275
0.50
15
1.3
0.252
6.4
368
41.7
295
0.75
20
3.5
0.434
11.0
991
112
268
1.00
25
2.9
0.599
15.2
821
93.0
117
1.25
32
3.5
0.808
20.5
991
112
77
1.50
40
3.5
0.926
23.5
991
112
58
2.00
50
14
1.156
29.4
3960
449
150
NOTES:
0.96
0.57
0.24
20.0
1.4
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G36
Edward Valves
Table 6
Hydraulic Stop Valve Flow Coefficients
Bold faced numerals are in U.S. customary units or dimensionless.
Brown numerals are in metric units.
SIZE
NPS
CHECK VALVES
WITH SPRINGS (STD)
CV
FL
xT
Ki
PFL
SPFL
CHECK VALVES
WITHOUT SPRINGS
PFL
SPFL
5,000 PSI (345 BAR) CWP Figure No. 158/158Y Hydraulic Stop Valves
10,000 PSI (690 BAR) CWP Figure No. 5158, 9158 Hydraulic Stop Valves
0.25
1.6
0.133
3.4
0.38
10
1.6
0.205
5.2
0.50
15
1.6
0.252
6.4
0.75
20
3.6
0.434
11.0
1.00
25
5.7
0.599
15.2
1.25
32
9.1
0.808
20.5
1.50
40
19
0.926
23.5
2.00
50
33
1.156
29.4
0.48
0.30
.024
N/A
Table 7
Inclined Bonnet Blow-Off Valve Flow Coefficients
Bold faced numerals are in U.S. customary units or dimensionless.
Brown numerals are in metric units.
SIZE
NPS
CHECK VALVES
WITH SPRINGS (STD)
CV
FL
xT
Ki
PFL
SPFL
CHECK VALVES
WITHOUT SPRINGS
PFL
SPFL
40
44
0.49
0.32
2.00
50
67
0.69
0.44
2.50
65
100
0.53
0.34
0.20
1.610
40.9
2.067
52.5
2.469
62.7
N/A
40
43
0.55
0.35
2.00
50
68
0.71
0.44
2.50
65
110
0.56
0.35
G37
0.20
1.500
38.1
1.939
49.3
2.323
59.0
N/A
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 8
Angle Blow-Off Valve Flow Coefficients
CHECK VALVES
WITH SPRINGS (STD)
CV
FL
xT
Ki
PFL
SPFL
CHECK VALVES
WITHOUT SPRINGS
PFL
SPFL
40
45
0.48
0.31
2.00
50
80
0.48
0.31
2.50
65
110
0.53
0.34
0.15
1.610
40.9
2.067
52.5
2.469
62.7
N/A
40
41
0.60
0.38
2.00
50
81
0.50
0.31
2.50
65
110
0.56
0.35
0.15
1.500
38.1
1.939
49.3
2.323
59.0
N/A
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G38
Edward Valves
Table 9
Crack-Open P for Edward Forged Steel Check Valves, PCO- PSI (BAR)
INSTALLATION
ORIENTATION
Horizontal
Bonnet up
0.7 0.9
0.05 0.06
0.1 0.5
0.007 0.03
Piston Lift
Horizontal
Bonnet sideways*
0.3 0.8
0.02 0.06
Horizontal
Bonnet down*
0.05 0.7
0.003 0.05
Vertical
Bonnet up
0.7 1.0
0.05 0.07
0.1 0.3
0.007 0.02
Vertical
Bonnet down*
0.05 0.7
0.003 0.05
Horizontal
Bonnet up
0.8 1.0
0.06 0.07
0.1 0.6
0.007 0.04
Piston Lift
Horizontal
Bonnet sideways*
0.4 0.8
0.03 0.06
Horizontal
Bonnet down*
0.05 0.6
0.003 0.04
0.4 0.8
0.03 0.06
Vertical
Inclined, Univalve
Horizontal
Bonnet up
1.0 1.5
0.07 0.10
0.4 0.8
0.03 0.06
Piston Lift
Horizontal
Bonnet sideways*
0.5 1.2
0.03 0.08
Horizontal
Bonnet down*
0.05 1.1
0.003 0.08
Vertical
Bonnet up
1.0 1.5
0.07 0.10
0.4 0.8
0.03 0.06
Vertical
Bonnet down*
0.05 1.1
0.003 0.08
Horizontal
Bonnet up
0.9 1.7
0.06 0.10
Horizontal
Bonnet sideways*
0.7 1.4
0.05 0.10
Horizontal
Bonnet down*
0.5 1.2
0.03 0.08
Vertical
Bonnet up
0.9 1.7
0.06 0.10
Vertical
Bonnet down*
0.5 1.2
0.03 0.08
G39
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Figure 16
Edward Forged Steel Check Valve Flow Performance Curves
Figure 16-A
RANGE DUE TO
VALVE-TO-VALVE
DESIGN VARIATIONS
Figure 16-B
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G40
Edward Valves
Table 10
Edward Cast Steel Globe Flow Coefficients
NPS
DN
CV
FL
xT
Ki
PCO
PFL
SPFL
PERF.
CURVES
FIG. 17
Class 300 (PN 50) Figure No. 318/318Y Stop valves, 304/304Y Stop-Check valves, 394/394Y Check valves
2.5
65
110
0.53
0.34
2.50
63.5
0.58
0.040
0.31
0.021
5630
637
46
80
84
0.80
0.43
0.20
3.00
76.2
0.79
0.054
1.3
0.088
5990
679
34
100
120
0.79
0.43
4.00
102
0.80
0.055
1.4
0.095
8980
1020
29
125
215
0.79
0.43
5.00
127
0.97
0.067
1.8
0.12
18,100
2050
37
150
335
0.80
0.44
6.00
152
1.2
0.084
2.3
0.16
31,900
3610
45
200
580
0.76
0.39
8.00
203
1.2
0.086
1.2
0.085
40,800
4620
33
10
250
1000
0.77
0.40
10.00
254
1.2
0.081
1.1
0.079
67,600
7660
34
12
300
1550
0.77
0.40
12.00
305
1.3
0.092
1.2
0.084
107,000
12,100
38
0.06
Class 600 (PN 110) Figure No. 616/616Y, 618/618Y, 716Y Stop valves, 606/604Y, 706Y Stop-Check valves,
694/694Y, 690/690Y, 794Y Check valves
2.5
65
84
0.97
0.61
80
120
0.97
0.61
2.50
63.5
0.79
0.054
1.3
0.088
5990
679
49
3.00
76.2
0.80
0.055
1.4
0.095
8980
1020
51
100
215
0.97
0.60
4.00
102
0.97
0.067
1.8
0.12
18,100
2050
58
125
335
0.97
0.61
5.00
127
1.2
0.084
2.3
0.16
31,900
3610
65
150
580
0.81
0.42
6.00
152
1.2
0.086
1.2
0.085
40,800
4620
58
200
1000
0.81
0.42
7.87
200
1.2
0.081
1.1
0.079
67,600
7660
56
10
250
1550
0.81
0.42
9.75
248
1.3
0.092
1.2
0.084
107,000
12,100
57
12
300
2200
0.81
0.42
11.75
298
1.5
0.10
1.4
0.099
169,000
19,100
62
14
350
2650
0.81
0.42
12.87
327
1.6
0.11
1.5
0.10
205,000
23,200
63
0.10
0.07
Class 900 (PN 150) Figure No. 4016/4016Y, 4316Y Stop valves, 4006/4006Y, 4306Y Stop-Check valves,
4094/4094Y, 4394Y Check valves
3
80
110
0.96
0.60
100
200
0.97
0.60
2.87
72.9
0.92
0.063
1.5
0.10
8510
964
53
3.87
98.2
1.3
0.090
2.3
0.16
19,500
2210
66
125
305
0.97
0.61
4.75
121
1.3
0.092
2.5
0.18
30,600
3470
69
150
530
0.81
0.42
5.75
146
1.2
0.085
1.5
0.10
41,500
4700
64
200
910
0.81
0.42
7.50
191
1.3
0.093
1.5
0.10
69,500
7870
63
10
250
1400
0.81
0.42
9.37
238
1.6
0.11
1.8
0.12
119,000
13,500
69
12
300
2000
0.81
0.42
11.12
282
1.8
0.12
2.1
0.14
182,000
20,600
75
14
350
2400
0.81
0.42
12.25
311
1.6
0.11
1.9
0.13
211,000
23,900
72
0.10
0.07
See note following paragraph 2.4.1, page G-28, for discussion of C factor.
G41
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 10 (cont.)
Edward Cast Steel Globe Flow Coefficients
NPS
DN
CV
FL
xT
Ki
PCO
PFL
SPFL
PERF.
CURVES
FIG. 17
Class 1500 (PN 260) Figure No. 2016, 7516/7516Y Stop valves, 2006Y, 7506/7506Y Stop-Check valves,
2094Y, 7594/7594Y Check valves
2.5
65
72
0.92
0.54
80
110
0.89
0.51
2.25
57.2
0.76
0.052
1.3
0.091
5230
592
53
2.75
69.9
0.92
0.063
1.5
0.10
8510
964
57
100
200
0.85
0.47
3.62
91.9
1.3
0.088
2.3
0.16
19,300
2190
75
125
300
0.83
0.44
4.37
111
1.2
0.080
2.2
0.15
28,600
3240
76
150
465
0.80
0.42
5.37
136
1.4
0.094
1.4
0.096
35,000
3960
62
0.08
200
790
0.81
0.42
7.00
178
1.6
0.11
1.4
0.097
59,300
6720
62
10
250
1250
0.81
0.42
8.75
222
1.5
0.10
1.4
0.100
93,900
10,600
63
12
300
1750
0.81
0.42
10.37
263
1.5
0.11
1.8
0.12
147,000
16,600
70
14
350
2100
0.81
0.42
11.37
289
1.7
0.12
2.1
0.14
190,000
21,500
75
0.07
Class 2500 (PN 420) Figure No. 3916/3916Y, 4416Y Stop valves, 3906/3906Y, 4406Y Stop-Check valves,
3994/3994Y, 4494Y Check valves
2.5
65
47
0.97
0.60
1.87
47.5
1.1
0.075
1.3
0.088
3370
382
49
80
68
0.97
0.61
2.25
57.2
1.4
0.093
1.6
0.11
5480
620
55
100
110
0.96
0.60
2.87
72.9
0.96
0.066
1.4
0.095
8280
938
51
125
175
0.97
0.60
3.62
91.9
1.4
0.097
2.2
0.15
16,600
1880
65
150
310
0.81
0.42
4.37
111
1.5
0.11
1.6
0.11
24,600
2790
66
200
530
0.81
0.42
5.75
146
2.2
0.15
2.2
0.15
49,800
5640
77
10
250
845
0.81
0.42
7.25
184
1.5
0.10
1.5
0.11
66,600
7540
65
12
300
1200
0.81
0.42
8.62
219
1.6
0.11
1.7
0.11
97,700
11,100
67
0.10
0.07
See note following paragraph 2.4.1, page G-28, for discussion of C factor.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G42
Edward Valves
Figure 17
Edward Cast Steel Globe Piston Lift Check Valve Performance Curves
Figure 17-A
Figure 17-B
G43
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 11
Edward Cast Steel Angle Valve Flow Coefficients
NPS
DN
CV
FL
xT
Ki
PCO
PFL
SPFL
PERF.
CURVES
FIG. 18
Class 300 (PN 50) Figure No. 319/319Y/329/329Y, Stop valves, 303/303Y, Stop-Check valves, 391/391Y/393/393Y Check valves
2.5
65
110
0.53
0.34
2.50
63.5
0.63
0.043
0.46
0.032
4940
559
40
80
135
0.59
0.24
0.15
3.00
76.2
0.79
0.054
0.55
0.038
6300
714
36
100
195
0.58
0.23
4.00
102
0.80
0.055
0.59
0.041
9460
1070
30
125
345
0.59
0.23
5.00
127
0.97
0.067
0.75
0.052
18,900
2140
39
150
535
0.59
0.24
6.00
152
1.2
0.084
0.96
0.066
33,200
3760
47
1
1
0.07
200
860
0.59
0.23
8.00
203
1.2
0.086
0.75
0.052
47,200
5340
38
10
250
1500
0.59
0.23
10.00
254
1.2
0.081
0.70
0.048
78,200
8860
40
12
300
2250
0.59
0.23
12.00
305
1.3
0.092
0.74
0.051
124,000
14,000
44
Class 600 (PN 110) Figure No. 617/617Y, 619/619Y, 717Y Stop valves, 605/605Y, 607/607, 707Y Stop-Check valves,
691/691Y, 695/695Y, 795Y Check valves
2.5
65
135
0.62
0.25
2.50
63.5
0.79
0.054
0.55
0.038
6300
714
51
80
195
0.62
0.25
3.00
76.2
0.80
0.055
0.59
0.041
9460
1070
54
100
345
0.62
0.25
4.00
102
0.97
0.067
0.75
0.051
18,800
2130
60
125
535
0.62
0.25
5.00
127
1.2
0.084
0.96
0.066
32,200
3760
68
150
860
0.64
0.25
6.00
152
1.2
0.086
0.75
0.052
47,200
5340
67
200
1500
0.63
0.25
7.87
200
1.2
0.081
0.70
0.048
78,200
8860
64
10
250
2250
0.63
0.25
9.75
248
1.3
0.092
0.74
0.051
124,000
14,000
66
12
300
3300
0.63
0.25
11.75
298
1.5
0.10
0.88
0.061
196,000
22,200
72
14
350
3950
0.63
0.25
12.87
327
1.6
0.11
0.90
0.062
237,000
26,900
73
0.08
Class 900 (PN 150) Figure No. 4017/4017Y, 4317Y Stop valves, 4007/4007Y, 4307Y Stop-Check valves,
4095/4095Y, 4395Y Check valves
3
80
180
0.62
0.24
2.87
72.9
0.92
0.063
0.64
0.044
8980
1020
56
100
325
0.62
0.25
3.87
98.2
1.5
0.10
1.2
0.081
22,200
2510
75
125
485
0.63
0.25
4.75
121
1.2
0.083
1.0
0.072
31,200
3530
70
150
790
0.63
0.25
5.75
146
1.3
0.092
1.0
0.071
50,900
5770
78
200
1350
0.63
0.25
7.50
190
1.4
0.099
1.0
0.071
86,600
9810
78
10
250
2100
0.63
0.25
9.37
238
1.7
0.12
1.3
0.090
152,000
17,200
88
12
300
2950
0.63
0.25
11.12
282
1.8
0.13
1.4
0.093
218,000
24,700
90
14
350
3600
0.63
0.25
12.25
311
1.5
0.10
1.3
0.091
261,000
29,600
89
16
400
6450
0.56
0.19
14.00
356
1.9
0.13
0.74
0.051
350,000
39,700
91
18
450
15.75
400
20
500
10,000
0.56
0.19
17.50
444
1.7
0.11
0.76
0.052
553,000
62,600
92
24
600
14,500
0.56
0.19
21.00
533
2.6
0.18
1.1
0.073
940,000
106,000
109
0.08
0.06
See note following paragraph 2.4.1, page G-28, for discussion of C factor.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G44
Edward Valves
Table 11 (cont.)
Edward Cast Steel Angle Valve Flow Coefficients
NPS
DN
CV
FL
xT
Ki
PCO
PFL
SPFL
PERF.
CURVES
FIG. 18
Class 1500 (PN 260) Figure No. 2017Y, 7517/7517Y Stop valves, 2007Y, 7507/7507Y Stop-Check valves,
2095Y, 7595/7595Y Check valves
2.5
65
115
0.59
0.22
2.25
57.2
0.75
0.052
0.58
0.040
5560
630
56
80
180
0.57
0.21
2.75
69.9
0.92
0.063
0.64
0.044
8980
1020
60
100
320
0.55
0.19
3.62
91.9
1.50
0.10
1.20
0.081
22,000
2490
86
125
475
0.54
0.18
4.37
111
1.30
0.093
1.20
0.083
33,000
3740
88
150
690
0.63
0.25
5.37
136
1.50
0.10
1.00
0.069
43,800
4970
77
200
1150
0.63
0.25
7.00
178
1.60
0.11
0.99
0.068
73,900
8370
77
10
250
1850
0.63
0.25
8.75
222
1.60
0.11
1.20
0.083
127,000
14,400
85
12
300
2550
0.63
0.25
10.37
263
1.80
0.13
1.40
0.094
190,000
21,500
90
14
350
3100
0.63
0.25
11.37
289
1.70
0.12
1.30
0.091
225,000
25,500
89
16
400
5550
0.56
0.19
13.00
330
2.00
0.14
0.79
0.055
313,000
35,400
94
18
450
5350
0.54
0.19
14.62
371
2.00
0.14
0.86
0.059
313,000
35,400
75
20
500
16.37
416
24
600
19.62
498
0.06
0.08
0.06
See note following paragraph 2.4.1, page G-28, for discussion of C factor.
* Consult Edward Sales Representative
Class 2500 (PN 420) Fig. No. 3917/3917Y, 4417Y Stop valves, 3907/3907Y, 4407Y Stop-Check valves, 3995/3995Y, 4495Y Check valves
2.5
65
75.5
0.62
0.24
1.87
47.5
1.1
0.075
0.57
0.039
3610
409
53
80
110
0.62
0.24
2.25
57.2
1.3
0.091
0.69
0.048
5770
653
58
100
180
0.62
0.24
2.87
72.9
0.96
0.066
0.61
0.042
8810
998
55
125
280
0.62
0.25
3.62
91.9
1.4
0.097
0.97
0.067
17,600
1990
68
150
455
0.63
0.25
4.37
111
1.5
0.11
0.96
0.066
28,300
3210
76
200
790
0.63
0.25
5.75
146
2.3
0.16
1.4
0.096
59,000
6680
91
10
250
1250
0.64
0.25
7.25
184
1.5
0.10
0.93
0.064
76,500
8660
74
12
300
1750
0.63
0.25
8.62
219
1.8
0.13
1.3
0.088
127,000
14,400
87
14
350
3400
0.40
0.10
9.50
241
2.1
0.14
0.89
0.061
204,000
23,100
115
16
400
3500
0.54
0.18
10.87
276
2.1
0.14
0.85
0.058
204,000
23,100
88
18
450
5450
0.50
0.15
12.25
311
2.5
0.17
1.00
0.069
347,000
39,300
118
20
500
5500
0.55
0.18
13.50
343
2.5
0.17
1.00
0.070
351,000
39,800
98
22
550
6900
0.55
0.18
14.87
378
2.5
0.17
0.97
0.067
429,000
48,600
99
24
600
0.08
0.05
See note following paragraph 2.4.1, page G-28, for discussion of C factor.
G45
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Figure 18
Edward Cast Steel Angle Piston Lift Check Valve Performance Curves
Figure 18-A
Figure 18-B
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G46
Edward Valves
Table 12
Edward Cast Steel Flite-Flow Stop & Stop-Check Valve Flow Coefficients
NPS
DN
CV
FL
xT
PERF.
CURVES
Ki
PCO
PFL
SPFL
FIG.19
C
Class 300/400 (PN 50/68) Figure No. 1314, 1314Y, 1329, 1329Y Stop valves; 1302, 1302Y Stop-Check valves; 1390, 1390Y, 1392, 1392Y Piston Lift Check valves
2-1/2
65
110
0.53
0.34
0.02
2.50
64
0.9
0.06
0.91
0.063
6,750
765
55
1, 2
80
295
0.52
0.20
0.08
3.00
76
0.8
0.06
0.64
0.044
15,000
1,680
85
4, 4
100
525
0.52
0.20
0.08
4.00
102
0.8
0.06
0.66
0.046
27,000
3,070
86
4, 4
150
1,200
0.52
0.20
0.08
6.00
152
0.7
0.05
0.71
0.049
63,000
7,120
89
4, 4
200
2,100
0.52
0.20
0.08
8.00
200
0.9
0.06
0.67
0.046
109,000
12,400
87
4, 4
10
250
3,300
0.52
0.20
0.08
10.00
248
1.0
0.07
0.76
0.052
181,000
20,500
92
4, 4
12
300
4,750
0.52
0.20
0.08
12.00
305
1.1
0.08
0.87
0.060
279,000
31,500
99
4, 4
14
350
4,750
0.52
0.20
0.08
12.00
305
1.1
0.08
0.87
0.060
279,000
31,500
99
4, 4
16
400
4,750
0.53
0.22
0.09
12.00
305
1.5
0.10
0.87
0.060
279,000
31,500
99
4, 4
4, 4
Class 600/700 (PN 110/120) Figure No. 614, 614Y, 714Y Stop valves; 602, 602Y, 702Y Stop-Check valves; 692, 692Y, 792Y Piston Lift Check valves
3
80
295
0.52
0.20
0.08
3.00
76.2
0.8
0.06
0.44
0.030
12,400
1,400
70
100
525
0.52
0.20
0.08
4.00
102
0.8
0.06
0.47
0.032
22,900
2,590
73
4, 4
150
1,200
0.52
0.20
0.08
6.00
152
0.7
0.05
0.53
0.037
54,500
6,170
77
4, 4
4, 4
200
2,050
0.52
0.20
0.08
7.87
200
0.9
0.06
0.68
0.047
106,000
12,000
87
10
250
3,100
0.52
0.20
0.08
9.75
248
1.0
0.07
0.85
0.059
182,000
20,600
98
4, 4
12
300
4,550
0.52
0.20
0.08
11.75
298
1.1
0.08
0.96
0.066
281,000
31,800
104
4, 4
14
350
4,550
0.52
0.20
0.08
11.75
298
1.1
0.08
0.96
0.066
281,000
31,800
104
4, 4
16
400
7,150
0.56
0.19
0.04
14.75
375
1.5
0.10
1.05
0.072
463,000
52,400
108
4, 4
20
500
11,000
0.52
0.20
0.08
18.25
484
1.4
0.10
0.96
0.066
677,000
76,700
104
1, 1
24
600
16,000
0.56
0.19
0.04
22.00
558
1.2
0.08
0.86
0.076
935,000
106,000
98
1, 2
4, 4
Class 900/1100 (PN 150/190) Figure No. 4014, 4014Y, 4314Y Stop valves; 4002, 4002Y, 4302Y Stop-Check valves;
4092, 4092Y, 4392Y Piston Lift Check valves
3
80
270
0.52
0.02
0.08
2.87
72.9
0.9
0.06
0.52
0.036
12,400
1,400
77
100
490
0.52
0.02
0.08
3.87
98.2
0.9
0.06
0.53
0.037
22,600
2,550
77
4, 4
150
1,100
0.52
0.02
0.08
5.75
146
0.7
0.05
0.50
0.034
48,500
5,490
75
4, 4
4, 4
200
1,850
0.52
0.02
0.08
7.50
191
0.8
0.06
0.65
0.045
94,200
10,700
85
10
250
2,900
0.52
0.02
0.08
9.37
238
1.0
0.07
0.84
0.058
167,000
18,900
97
4, 4
12
300
4,050
0.52
0.02
0.08
11.12
282
1.1
0.08
0.93
0.064
248,000
28,100
102
4, 4
14
350
4,050
0.52
0.02
0.08
11.12
282
1.1
0.08
0.93
0.064
248,000
28,100
102
4, 4
16
400
6,450
0.52
0.02
0.08
14.00
356
1.3
0.09
1.09
0.075
426,000
48,200
111
4, 4
See note following paragraph 2.4.1, page G-28, for discussion of C factor.
* Consult Edward Sales Representative
G47
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 12 (cont.)
Edward Cast Steel Flite-Flow Stop & Stop-Check Valve Flow Coefficients
NPS
DN
CV
FL
xT
Ki
PCO
PFL
SPFL
PERF.
CURVES
FIG. 19
A, B
Class 1500/1800 (PN 260/310) Figure No. 2014Y, 7514Y Stop valves; 2002Y, 7502Y Stop-Check valves; 2092Y, 7592Y Check valves
3
80
270
0.52
0.20
100
425
0.52
0.20
150
950
0.61
200
1,600
10
250
12
14
2.87
72.9
1.0
0.07
0.51
0.035
12,200
1,380
75
4, 4
3.62
91.9
1.0
0.07
0.62
0.043
21,200
2,400
82
4, 4
0.23
5.37
136
1.3
0.09
0.73
0.050
51,200
5,800
90
1, 3
0.61
0.23
7.00
178
1.5
0.10
0.74
0.051
87,800
9,940
91
1, 2
2,500
0.61
0.23
8.75
222
1.5
0.10
0.89
0.061
150,000
17,000
100
1, 2
300
3,550
0.61
0.23
10.37
263
1.7
0.12
1.01
0.070
225,000
25,500
107
1, 2
350
3,550
0.59
0.22
10.37
263
1.7
0.12
1.01
0.070
225,000
25,500
106
1, 2
16
400
5,550
0.61
0.23
13.00
330
1.8
0.12
1.09
0.075
366,000
41,500
110
1, 2
18
450
5,550
0.59
0.22
13.00
330
1.8
0.12
1.09
0.075
366,000
41,500
110
1, 2
20
500
8,800
0.61
0.23
16.37
416
2.2
0.15
1.46
0.101
673,000
76,200
128
1, 2
24
600
8,800
0.59
0.23
16.37
416
2.3
0.16
0.08
0.05
0.06
Class 2500/2900 (PN 460/490) Figure No. 3914Y, 4414Y Stop valves, 3902Y, 4402Y Stop-Check valves, 3992Y, 4492Y Check valves
Class 2900 (PN 490) Size 3 and 4 only with figure numbers the same as Class 2500 valves.
3
80
165
0.52
0.20
100
270
0.52
0.20
150
625
0.61
200
1,100
10
250
12
2.25
57.2
1.1
0.08
0.71
0.049
8,850
1,000
89
4, 4
2.87
72.9
0.9
0.06
0.70
0.048
14,300
1,620
88
4, 4
0.23
4.37
111
1.5
0.11
0.84
0.058
36,300
4,110
97
1, 2
0.61
0.23
5.75
146
2.1
0.15
1.13
0.078
73,000
8,270
112
1, 2
1,750
0.61
0.22
7.25
184
1.5
0.10
0.80
0.055
97,600
11,100
95
1, 2
300
2,450
0.61
0.22
8.62
219
1.7
0.12
0.96
0.066
151,000
17,100
103
1, 3
14
350
3,550
0.53
0.17
10.37
263
1.9
0.13
1.17
0.081
242,000
27,400
115
1, 2
16
400
3,550
0.60
0.22
10.37
263
1.9
0.13
1.17
0.081
242,000
27,400
115
1, 2
18
450
5,550
0.55
0.18
13.00
330
2.3
0.16
1.38
0.095
412,000
46,700
124
1, 2
20
500
5,550
0.54
0.18
13.00
330
2.3
0.16
1.38
0.095
412,000
46,700
124
1, 2
24
600
8,100
0.60
0.22
15.69
399
2.4
0.17
1.61
0.111
648,000
73,400
134
1, 2
8,290
939
75
1, 2
1, 2
0.08
0.05
Series 4500 Figure No. 4514Y, 5014Y Stop valves, 4502Y, 5002Y Stop-Check valves, 4592Y, 5092Y Check valves
4
100
135
0.66
0.26
150
305
0.64
0.24
200
740
0.48
0.14
10
250
1,100
0.51
0.16
0.06
0.3
2.37
60.2
1.2
0.08
0.97
0.067
3.37
85.6
1.5
0.10
1.75
0.121
25,300
2,870
113
4.75
121
2.3
0.16
0.83
0.057
42,800
4,840
97
1, 2
5.75
146
1.7
0.12
0.86
0.059
63,600
7,200
98
1, 3
See note following paragraph 2.4.1, page G-28, for discussion of C factor.
* Consult Edward Sales Representative
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G48
Edward Valves
Table 12 (cont.)
Edward Cast Steel Flite-Flow Stop & Stop-Check Valve Flow Coefficients
Bold faced numerals are in U.S. customary units or dimensionless.
Brown numerals are in metric units.
SIZE
NPS
DN
CV
FL
xT
PERF.
CURVES
FIG. 19
Ki
PCO
PFL
SPFL
Class 2000 (PN 340) Figure No. 2214Y, 3214Y Stop valves; 2002Y, 3202Y Stop-Check valves; 2292Y, 3292Y Check valves
12
300
2950
0.52
0.20
14
350
2950
0.52
0.20
0.08
9.50
241
1.7
0.12
0.85
0.059
172,600
19,500
97
4, 4
9.50
241
1.7
0.12
0.85
0.059
172,600
19,500
97
4, 4
Figure 19
Cast Steel Flite-Flow Piston Lift Check Valve Performance Curves
Figure 19-A
G49
Figure 19-B
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 13
Edward Cast Steel Tilting Disk Check Valve Flow Coefficients
NPS
DN
CV
FL
xT
Ki
PFL
SPFL
PERF.
CURVES
FIG. 20
150
1110
0.57
0.20
6.00
152
0.80
0.055
62,300
7,060
88
200
1850
0.57
0.20
7.87
200
1.0
0.069
115,000
13,000
95
10
250
2850
0.57
0.20
9.75
248
1.1
0.076
187,000
21,200
100
12
300
4100
0.57
0.20
11.75
298
1.2
0.083
285,000
32,300
105
14
350
4050
0.56
0.20
12.87
327
1.2
0.083
285,000
32,300
88
16
400
6500
0.57
0.20
14.75
375
1.4
0.097
481,000
54,500
113
18
450
8100
0.57
0.20
16.50
419
1.5
0.10
622,000
70,500
116
20
500
9950
0.57
0.20
18.25
464
1.6
0.11
786,000
89,000
120
0.05
65
195
0.44
0.12
2.25
57.2
1.0
0.069
12,200
1,380
123
80
245
0.57
0.20
0.02
2.87
72.9
0.60
0.041
12,200
1,380
75
100
215
0.59
0.23
3.87
98.2
0.80
0.055
12,200
1,380
41
150
990
0.57
0.20
5.75
146
0.80
0.055
56,800
6,430
87
200
1700
0.57
0.20
7.50
190
0.80
0.055
97,000
11,000
88
10
250
2400
0.56
0.20
9.37
238
0.90
0.062
145,000
16,400
84
12
300
3450
0.56
0.20
11.12
282
1.1
0.076
233,000
26,400
96
14
350
3300
0.56
0.20
12.25
311
1.3
0.090
233,000
26,400
79
16
400
4950
0.56
0.20
14.00
356
1.3
0.090
360,000
40,800
94
18
450
4700
0.57
0.21
15.75
400
1.5
0.10
360,000
40,800
74
20
500
9150
0.57
0.20
17.50
444
1.2
0.083
713,000
80,800
119
0.05
65
195
0.44
0.12
2.25
57.2
1.0
0.069
12,200
1,380
123
80
245
0.52
0.17
0.02
2.75
69.9
0.60
0.041
12,200
1,380
82
100
225
0.57
0.22
3.62
91.9
0.70
0.048
12,200
1,380
47
150
970
0.51
0.16
5.37
136
0.90
0.062
56,800
6,430
100
200
1650
0.51
0.16
7.00
178
0.90
0.062
97,000
11,000
101
10
250
2400
0.54
0.18
8.75
222
0.90
0.062
145,000
16,400
96
12
300
3450
0.53
0.17
10.37
263
1.1
0.076
233,000
26,400
110
14
350
3400
0.56
0.20
11.37
289
1.2
0.083
233,000
26,400
92
16
400
5050
0.57
0.20
13.00
330
1.3
0.090
360,000
40,800
108
18
450
4900
0.56
0.20
14.62
371
1.4
0.097
360,000
40,800
86
24
600
10,500
0.56
0.20
19.62
498
1.5
0.10
824,000
93,400
109
0.05
See note following paragraph 2.4.1, page G-28, for discussion of C factor.
1 Crack open pressure drop P
CO values are generally less than 0.25 psi (0.01 bar).
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G50
Edward Valves
Table 13 (cont.)
Edward Cast Steel Tilting Disk Check Valve Flow Coefficients
NPS
DN
CV
FL
xT
Ki
PFL
SPFL
PERF.
CURVES
FIG. 20
65
125
0.47
0.13
80
195
0.44
0.12
1.87
47.5
2.4
0.17
12,200
1,380
178
2.25
57.2
1.0
0.069
12,200
1,380
123
100
245
0.57
0.20
2.87
72.9
0.60
0.041
12,200
1,380
75
150
655
0.50
0.15
4.37
111
0.40
0.028
26,500
3,000
71
200
990
0.57
0.20
5.75
146
0.80
0.055
56,700
6,420
87
10
250
1650
0.54
0.18
7.25
184
0.90
0.062
97,000
11,000
94
12
300
2400
0.53
0.17
8.62
219
0.50
0.034
156,000
17,700
107
14
350
3250
0.47
0.14
9.50
241
1.3
0.090
233,000
26,400
131
16
400
3450
0.57
0.20
10.87
276
1.1
0.076
233,000
26,400
100
18
450
5050
0.51
0.16
12.25
311
1.3
0.090
360,000
40,800
122
20
500
5000
0.56
0.20
13.50
343
1.3
0.090
360,000
40,800
101
3.76
95.5
0.70
0.048
21,900
2480
79
4.75
121
0.8
0.055
37,000
4190
84
0.01
0.05
Class 4500 (PN 760) Figure No. 4570Y, 5070Y Check valves
6
150
420
0.43
0.11
200
675
0.45
0.12
.03
See note following paragraph 2.4.1, page G-28, for discussion of C factor.
1 Crack open pressure drop P
CO values are generally less than 0.25 psi (0.01 bar).
G51
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Figure 20
Tilting Disk Check Valve Performance Curves
Figure 20-A
Figure 20-B
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G52
Edward Valves
Table 14
Edward Cast Steel Equiwedge Gate Valve Flow Coefficients
Size
NPS
Size
DN
CV
FL
XT
Ki
NPS
DN
CV
FL
XT
Ki
2.5
65
395
0.74
0.23
0.02
2.50
63.5
2.5
65
385
0.76
0.25
0.02
2.50
63.5
3.0
80
325
0.57
0.19
0.02
3.00
76.2
3.0
80
365
0.55
0.16
0.02
2.90
73.7
4.0
100
545
0.58
0.20
0.03
4.00
102
4.0
100
625
0.53
0.16
0.03
3.83
97.3
6.0
150
2350
0.38
0.08
0.02
6.00
152
6.0
150
2350
0.41
0.09
0.02
5.75
146
2.5
65
270
0.88
0.33
0.02
2.25
57.2
2.5
65
280
0.75
0.24
0.02
2.12
53.8
3.0
80
340
0.60
0.20
0.03
2.87
72.9
3.0
80
400
0.61
0.18
0.03
2.62
66.5
4.0
100
570
0.40
0.18
0.02
3.87
98.2
4.0
100
670
0.54
0.15
0.02
3.62
91.9
Size
NPS
Size
DN
CV
FL
XT
Ki
NPS
DN
CV
FL
XT
Ki
Class 600 (PN 110) Figure No. 1611BY, 1711BY Stop valves
Class 600 (PN 110) Figure No. 1611/ 1611Y, 1711Y Stop valves
2.5
65
380
0.77
0.25
0.02
2.50
63.5
3.0
80
610
0.44
0.10
0.02
3.00
76.2
4.0
100
1250
0.41
0.08
0.03
4.00
102
6.0
150
3250
0.40
0.07
0.02
6.00
152
8.0
200
5300
0.35
0.06
0.02
7.87
200
8x6x8
200x150x200
2650
0.33
0.07
0.03
7.87
200
10.0
250
8550
0.34
0.06
0.01
9.75
248
10x8x10
250x200x250
4500
0.32
0.07
0.02
9.75
248
12.0
300
12,000
0.31
0.05
0.01
11.75
298
12x10x12
300x250x300
7100
0.32
0.06
0.02
11.75
298
14.0
350
14,000
0.32
0.05
0.01
12.87
327
14x12x14
350x300x350
9900
0.32
0.06
0.02
12.87
327
16.0
400
18,500
0.32
0.05
0.01
14.75
375
16x14x16
400x350x400
12,000
0.31
0.06
0.02
14.75
375
18.0
450
25,500
0.30
0.05
0.01
16.50
419
18x16x18
450x400x450
17,500
0.29
0.05
0.01
16.50
419
20.0
500
30,500
0.31
0.05
0.01
18.25
464
20x18x20
500x450x500
22,000
0.30
0.06
0.02
18.25
464
22.0
550
36,500
0.30
0.05
0.01
20.12
511
22x20x22
550x500x550
29,000
0.28
0.05
0.01
20.12
511
24.0
600
46,500
0.30
0.05
0.01
22.00
559
24x20x24
600x500x600
24,500
0.30
0.06
0.02
22.00
559
26.0
650
53,500
0.30
0.05
0.01
23.75
603
26x22x26
650x550x650
30,000
0.30
0.06
0.02
23.75
603
28.0
700
62,500
0.29
0.04
0.01
25.50
648
28x24x28
700x600x700
40,500
0.29
0.05
0.01
25.50
648
30x26x30
750x650x750
46,500
0.29
0.05
0.01
27.37
695
32x28x32
800x700x800
52,000
0.30
0.05
0.01
29.25
743
G53
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Table 14 (cont.)
Edward Cast Steel Equiwedge Gate Valve Flow Coefficients
Size
NPS
Size
DN
CV
FL
XT
Ki
NPS
DN
CV
FL
XT
Ki
Class 900 (PN 150) Figure No. 1911BY, 14311BY Stop valves
Class 900 (PN 150) Figure No. 1911/ 1911Y, 14311Y Stop valves
2.5
65
380
0.63
0.17
0.02
2.25
57.2
3.0
80
455
0.44
0.11
0.03
2.87
72.9
4.0
100
990
0.42
0.09
0.02
3.87
98.2
6.0
150
2350
0.41
0.09
0.02
5.75
146
8.0
200
4200
0.37
0.07
0.02
7.50
190
8x6x8
200x150x200
2000
0.37
0.09
0.03
7.50
190
10.0
250
6250
0.40
0.08
0.02
9.37
238
10x8x10
250x200x250
3500
0.35
0.08
0.02
9.37
238
12.0
300
9500
0.36
0.07
0.02
11.12
282
12x10x12
300x250x300
5950
0.35
0.08
0.02
11.12
282
14.0
350
12,000
0.35
0.06
0.02
12.25
311
14x12x14
350x300x350
7700
0.39
0.09
0.03
12.25
311
16.0
400
15,000
0.35
0.06
0.02
14.00
356
16x14x16
400x350x400
10,000
0.35
0.07
0.02
14.00
356
18.0
450
19,500
0.33
0.06
0.02
15.75
400
18x16x18
450x400x450
14,000
0.32
0.06
0.02
15.75
400
20.0
500
26,000
0.35
0.06
0.02
17.50
444
20x18x20
500x450x500
18,000
0.32
0.06
0.02
17.50
444
22.0
550
28,000
0.38
0.07
0.02
19.25
489
22x20x22
550x500x550
25,000
0.31
0.06
0.02
19.25
489
24.0
600
38,000
0.32
0.05
0.01
21.00
533
24x20x24
600x500x600
23,000
0.31
0.06
0.02
21.00
533
26.0
650
45,000
0.32
0.05
0.01
22.75
578
26x22x26
650x550x650
28,000
0.31
0.06
0.02
22.75
578
28.0
700
52,500
0.31
0.05
0.01
24.50
622
28x24x28
700x600x700
33,500
0.31
0.06
0.02
24.50
622
30x26x30
750x650x750
38,000
0.32
0.06
0.02
26.25
667
32x28x32
800x700x800
48,000
0.29
0.05
0.01
28.00
711
65
305
0.78
0.26
0.02
2.25
57.2
3.0
80
420
0.52
0.14
0.03
2.75
69.9
4.0
100
760
0.47
0.12
0.03
3.62
91.9
6.0
150
1650
0.54
0.15
0.04
5.37
136
8.0
200
3150
0.48
0.12
0.03
7.00
178
8x6x8
200x150x200
1650
0.43
0.12
0.04
7.00
178
10.0
250
5500
0.40
0.08
0.02
8.75
222
10x8x10
250x200x250
2950
0.41
0.11
0.03
8.75
222
12.0
300
6850
0.42
0.09
0.02
10.37
263
12x10x12
300x250x300
4500
0.40
0.10
0.03
10.37
263
14.0
350
9700
0.40
0.08
0.02
11.37
289
14x12x14
350x300x350
7050
0.37
0.08
0.02
11.37
289
16.0
400
12,000
0.39
0.08
0.02
13.00
330
16x14x16
400x350x400
8700
0.37
0.08
0.02
13.00
330
18.0
450
15,000
0.37
0.07
0.02
14.62
371
18x16x18
450x400x450
11,000
0.37
0.08
0.02
14.62
371
20.0
500
18,500
0.37
0.07
0.02
16.37
416
20x18x20
500x450x500
13,500
0.36
0.08
0.02
16.37
416
22.0
550
23,000
0.37
0.07
0.02
18.00
457
22x20x22
550x500x550
18,000
0.34
0.07
0.02
18.00
457
24.0
600
27,000
0.37
0.08
0.02
19.62
498
24x20x24
600x500x600
17,000
0.35
0.07
0.02
19.62
498
26x22x26
650x550x650
20,500
0.35
0.07
0.02
21.25
540
28x24x28
700x600x700
24,000
0.36
0.08
0.02
23.00
584
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G54
Edward Valves
Table 14 (cont.)
Edward Cast Steel Equiwedge Gate Valve Flow Coefficients
Bold faced numerals are in U.S. customary units or dimensionless.
Brown numerals are in metric units.
Regular Port Gate Valves
Size
NPS
Size
DN
CV
FL
XT
Ki
NPS
DN
CV
FL
XT
Ki
2.5
65
150
0.78
0.50
0.02
1.87
47.5
3.0
80
230
0.58
0.18
0.04
2.25
57.2
4.0
100
340
0.59
0.19
0.04
2.87
72.9
6.0
150
910
0.61
0.19
0.05
4.37
111
8.0
200
1850
0.51
0.14
0.04
5.75
146
8x6x8
200x150x200
1000
0.44
0.12
0.04
5.75
146
10.0
250
2950
0.48
0.12
0.03
7.25
184
10x8x10
250x200x250
1650
0.46
0.14
0.04
7.25
184
12.0
300
4350
0.46
0.11
0.03
8.62
219
12x10x12
300x250x300
2750
0.43
0.11
0.03
8.62
219
14.0
350
5150
0.47
0.12
0.03
9.50
241
14x12x14
350x300x350
3900
0.46
0.13
0.03
9.50
241
16.0
400
7050
0.46
0.11
0.03
10.87
276
16x14x16
400x350x400
4850
0.44
0.12
0.03
10.87
276
18.0
450
8950
0.46
0.11
0.03
12.25
311
18x16x18
450x400x450
6450
0.43
0.11
0.03
12.25
311
20.0
500
11,500
0.45
0.11
0.03
13.50
343
20x18x20
500x450x500
8200
0.44
0.12
0.03
13.50
343
22.0
550
14,000
0.45
0.11
0.03
14.87
378
22x20x22
550x500x550
11,500
0.39
0.10
0.03
14.87
378
24.0
600
17,500
0.43
0.10
0.03
16.25
413
24x20x24
600x500x600
10,500
0.39
0.10
0.03
16.25
413
26x22x26
650x550x650
13,000
0.39
0.09
0.02
17.62
448
28x24x28
700x600x700
16,000
0.39
0.09
0.03
19.00
483
Table 15
Edward Forged Steel Hermavalve Flow Coefficients
Bold faced numerals are in U.S. customary units or dimensionless.
Brown numerals are in metric units.
REGULAR PORT HERMAVALVES Fig. No.
15004/15104, 15008/15108, 16004, 16008
NPS
DN
CV
FL
xT
Ki
CV
FL
xT
Ki
0.05
0.75
15
20
4.9
6.1
0.46
0.52
0.31
0.36
0.07
0.09
0.464
0.612
11.8
15.5
1.00
25
11
0.55
0.38
0.10
6.1
0.51
0.36
0.09
0.815
20.7
1.50
40
32
0.62
0.39
0.13
11
0.53
0.37
0.09
1.338
34.0
2.00
50
50
0.68
0.40
0.15
32
0.57
0.37
0.11
1.687
42.8
2.50
65
50
0.59
0.37
0.12
2.125
54.0
G55
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Figure 21
Ratio of Specific Heats (k) for Some Gases
k = 1.3
Ammonia
Carbon Dioxide
Dry Steam
Methane
Natural Gas
k = 1.4
Air
Carbon Monoxide
Hydrogen
Nitrogen
Oxygen
Figure 22A
Saturated Water - Temperature, Pressure & Density
(U.S. Units)
Water Temp. F
32
70
100
200
300
400
500
550
600
650
700
705
Vapor Pressure, pV
0.09
0.36
0.95
11.5
67
247
681
1045
1543
2208
3094
3206
Water Density,
62.4
62.3
62.0
60.1
57.3
53.7
49.0
46.0
42.3
37.4
27.3
19.7
lb./ft3
Figure 22B
Saturated Water - Temperature, Pressure & Density
(Metric)
Water Temp. C
25
50
100
150
200
250
300
350
370
374
Vapor Pressure, pV
.006
.032
.123
1.01
4.76
15.6
39.8
85.9
165.4
211
221
Water Density,
1000
997
988
958
917
865
799
712
574
452
315
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G56
Edward Valves
G57
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
1 mile = 5280 ft
1 mile = 1.609 km
1 km = 3281 ft
1 m = 39.37 in.
Pressure Head
Specific gravities are sometimes given with two temperatures indicated, e.g.,
p(psi) =
Area
1 in.2 = 645.2 mm2
1 in.2 = 6.452 cm2
1 ft2 = 144 in.2
1 m2 = 10.76 ft2
1 m2 = 1550 in.2
Volume
1 in.3 = 16.39 cm3
1 ft3 = 1728 in.3
1 U.S. gal. = 231 in.3
1 U.S. gal. = 0.1337 ft3
1 U.S. gal. = 0.8327
Imp. gal.
1 U.S. gal. = 3.7854 liters
1 ft3 = 28.32 liters
1 m3 = 35.31 ft3
1 m3 = 264.2 U.S. gal.
1 m3 = 220 Imp. gal.
1 m3 = 1000 liters
1 liter = 61.02 in.3
1 liter = 1000 cm 3
1 ml = 1 cm
Density
Gl
60F
15.5C Gl 60F/60
, Gl
,
60F
4C
Gl 60F/60 =
141.5
131.5 + API degrees
T(F -32)
1.8
T(F) = 1.8 T(C) + 32
T(R) = T(F) + 460
T(K) = T(C) + 273
T(R) = 1.8 T(K)
density of gas
(at pressure and temperature of interest)
Gg =
density of air
(at same pressure and temperature)
where:
C = degrees Celsius
F = degrees Fahrenheit
K = degrees Kelvin (absolute temperature)
R = degrees Rankine (absolute temperature)
density of liquid
density of water at reference condition
Gl =
and
density of liquid
density of water at 4C
and atmospheric pressure
Gl =
(lb/ft3)
62.38 (lb/ft3)
(kg/m3)
1000 (kg/m3)
Flow Rate
Temperature
T(C) =
Specific Volume
p(N/m2) =
p(bar) =
The upper temperature is that of the liquid whose specific gravity is given, and the lower value indicates the
water temperature of the reference density. If no temperatures are shown, assume that the commonly used
relations apply.
Pressure
mass units
1 lb/hr = 0.4536 kg/hr
1 metric tonne/hr = 2205 lb/hr
liquid volume units
1 U.S. gpm = 34.28 BOPD
BOPD = barrels oil per day
1 U.S. gpm = 0.8327 Imp. gpm
1 U.S. gpm = 0.2273 m3/hr
1 U.S. gpm = 3.785 liters/min
1 m3/hr = 16.68 liters/min
1 ft3/s = 448.8 U.S. gpm
mixed units
w(lb/hr) = 8.021 q(U.S. gpm) x (lb/ft3)
w(lb/hr) = 500 q(U.S. gpm of water at 70F or less)
In the following:
STP (standard conditions) refers to 60F, 14.73 psia
NTP (normal conditions) refers to 0F, 1.0135 bar abs
Gg =
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G58
Edward Valves
G59
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G60
Edward Valves
The properties of Stellite 21 also provide an advantage to the user long after a valve leaves the Edward
plant. If a large valve seat is severely damaged in a
localized area, as may occur due to closing on foreign
objects, the seat may be repaired locally and refinished, in such cases, where a valve cannot be adequately preheated before welding, a Stellite 6 seat
may crack during the repair process requiring
either removal of the valve from the line or in situ
removal replacement of the complete seat.
Some Edward valves have used solid disks made of
hardened ASTM A-565 Grade 616 or 615 stainless
steel. This corrosion-resistant alloy has been proven
in seating and erosion tests and in service. This
material can be furnished in certain valves for
nuclear-plant services where reduced cobalt is desirable. Similar iron-base trim materials are used in
production of certain standard valves. Extensive
research on other cobalt-free valve trim materials has
also identified other alloys which provide good performance under many service conditions. Consult
Edward Valves about any special trim requirements.
Registered Trademark Stoody Co.
G61
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
TITLE
V-REP 74-3
V-REP 75-5
V-REP 78-3
V-REP 78-4
V-REP 79-4
V-REP 80-1
V-REP 80-3
V-REP 81-1
V-REP 81-2
V-REP 82-1
V-REP 82-2
V-REP 84-1
V-REP 85-2
V-REP 86-2
Tests of Asbestos-Free Stem Packings for Valves for Elevated Temperature Service
V-REP 90-1
Design Basis Qualification of Equiwedge Gate Valves for Safety-Related MOV Applications
V-REP 90-2
Flow Performance, Stability and Sealability of Piston Lift and Tilting Disk Check Valves
V-REP 90-3
V-REP 91-1
V-REP 92-1
V-REP 93-1
PressurCombo
V-REP 95-1
And from:
National Technical Information Service
Springfield, Virginia 22161
EPRI Report No. NP 5479
Application Guidelines for Check Valves
in Nuclear Power Plants
Available from:
Electric Power Research Institute
Research Reports Center
P.O. Box 50490
Palo Alto, CA 94303
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
G62
Edward Valves
EV100
5th Edition
Edward Valves
ELEMENTS
PERCENTAGE*
CAST
Chromium-Molybenum (Bolting)
ASTM A193 Grade B7
Forged - ASTM A105
FORGED
Carbon
Manganese
Phosphorus
Sulfur
Silicon
0.30 max.
1.00 max.
0.04 max.
0.045 max.
0.60 max.
0.22 max.
.60 to 1.05
0.04 max.
0.05 max.
0.35 max.
Carbon
Manganese
Phosphorus
Sulfur
Silicon
Chromium
Molybdenum
0.20 max.
0.50 to 0.80
0.04 max.
0.045 max.
0.60 max.
1.00 to 1.50
0.45 to 0.65
0.10 to 0.15
0.30 to 0.80
0.04 max.
0.04 max.
0.50 to 1.00
1.00 to 1.50
0.44 to 0.65
Carbon
Manganese
Phosphorus
Sulfur
Silicon
Chromium
Molybdenum
0.18 max.
0.40 to 0.70
0.04 max.
0.045 max.
0.60 max.
2.00 to 2.75
0.90 to 1.20
0.15 max.
0.30 to 0.60
0.04 max.
0.04 max.
0.50 max.
2.00 to 2.50
0.87 to 1.13
Carbon
Manganese
Phosphorus
Sulfur
Silicon
Chromium
Molybdenum
Columbium
Venadium
Nitrogen
Nickel
0.12 max.
0.30-0.60 max.
0.02 max.
0.018 max.
0.20-0.50
8.0-9.5
0.85-1.05
0.060-0.10
0.18-0.25
0.030-0.070
0.40 max.
0.08-0.12 max.
0.30-0.60 max.
0.02 max.
0.01 max.
0.20-0.50 max.
8.00-9.50
0.85-1.05
0.060-0.10
0.18-0.25
0.030-0.070
0.40 max.
Carbon
Manganese
Phosphorus
Nickel
Sulfur
Silicon
Chromium
Molybdenum
0.03 max.
1.50 max.
0.04 max.
9.00 to 13.00
0.04 max.
1.50 max.
17.00 to 21.00
2.00 to 3.00
0.08 max.
2.00 max.
0.04 max.
10.00 to 14.00
0.03 max.
1.00 max.
16.00 to 18.00
2.00 to 3.00
Carbon
Manganese
Phosphorus
Sulfur
Silicon
Nickel
Chromium
Molybdenum
0.15 max.
1.00 max.
0.04 max.
0.03 max.
1.00 max.
0.50 max.
11.50 to 13.50
0.15 max.
1.25 max.
0.06 max.
0.15 min.
1.00 max
12.00 to 14.00
0.60 max.
Copper
Aluminum
Iron
Tin
Lead
Manganese
Zinc
Silicon
Nickel & Cobalt
remainder
10.00 to 11.50
3.00 to 5.00
0.50 max.
1.50 max.
61900
remainder
8.50 to 10.00
3.00 to 4.50
0.60 max.
0.80 max.
0.02 max.
Carbon
Manganese
Phosphorus
Sulfur
Silicon
Chromium
Molybdenum
0.37 to 0.49
0.65 to 1.10
0.035 max.
0.04 max.
0.15 to 0.35
0.75 to 1.20
0.15 to 0.25
Chromium
Manganese
Molybdenum
Nickel
Iron
Boron
Carbon
Silicon
25.00 to 29.00
1.00 max.
5.00 to 6.00
1.75 to 3.75
3.00
.007 max.
0.20 to 0.30
1.00
62300
remainder
8.50 to 11.00
2.00 to 4.00
0.60 max.
0.50 max.
0.25 max.
1.00 max.
This ASTM specification data is provided for customer information. The data was based on information available at time of printing and may not reflect
the latest ASTM revision. Edward suggests referring to the applicable specification for complete information or contacting your Edward Valves sales
representative.
*The equivalent Edward valve material specification for valve bodies meets all of the requirements of the referenced ASTM Specification; additionally Edward restricts certain elements
(i.e. carbon, manganese) to tighter allowable ranges to enhance weldability.
H2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A105
(3) (5)
A182
F22
(4) (5)
NOTES:
TEMP.
F
-20 to 100
200
300
400
500
600
650
700
750
800
850
900
950
1000
-20 to 100
200
300
400
500
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
CLASS 2500
SIZES
1/2 thru 1
THREADED
(1)
4225
4225
4225
4225
4225
4015
3940
3910
3550
2895
1880
1205
745
390
4225
4225
4175
4080
4055
4055
4035
4005
3885
3790
3620
3380
2720
1980
1330
830
525
315
4225
4225
4225
4225
4225
4015
3940
3910
3550
2895
1880
1205
725
360
4225
4225
4175
4080
4055
4055
4035
4005
3885
3790
3620
3380
2655
1835
1235
770
485
290
6250
6250
6250
6250
6250
5940
5825
5780
5250
4285
2785
1785
1110
600
6250
6250
6180
6035
6000
6000
5965
5930
5750
5605
5355
5000
4075
3040
PRESSURE (PSIG)
CLASS 2680
CLASS 4500
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
6700
6700
6700
6700
6700
6370
6245
6195
5630
4595
2985
1915
1190
650
6700
6700
6625
6470
6430
6430
6395
6355
6165
6010
5740
5360
4385
3290
2205
1385
865
520
6700
6700
6700
6700
6700
6370
6245
6195
5630
4595
2985
1915
1145
575
6700
6700
6625
6470
6430
6430
6395
6355
6165
6010
5740
5360
4215
2910
1950
1225
765
460
11,250
11,250
11,250
11,250
11,250
10,690
10,485
10,405
9450
7715
5015
3215
2065
1195
11,250
11,250
11,120
10,865
10,800
10,800
10,735
10,670
10,350
10,095
9645
9000
7555
6050
4065
2545
1590
955
11,250
11,250
11,250
11,250
11,250
10,690
10,485
10,405
9450
7715
5015
3215
1930
965
11,250
11,250
11,120
10,865
10,800
10,800
10,735
10,670
10,350
10,095
9645
9000
7070
4885
3280
2055
1285
770
1. Limited Class, Sizes 2-1/2 and smaller, all types ends except flanges. Threaded ends limited to Size 1 and smaller and 1000 F maximum.
2. Special Class, Sizes 3 and 4, buttwelding ends only.
3. Permissible but not recommended for prolonged usage above approx. 800F.
4. Permissible but not recommended for use above 1100F.
5. Shaded ratings may require special trim and packing, consult your Edward Valves sales representative for applications in these ranges.
6. The 10,800 repeats because ASME B16.34 rating rules do not permit increasing pressure ratings at higher temperatures.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H3
Edward Valves
MATERIAL
A105
(3) (5)
A182
F22
(4) (5)
NOTES:
H4
TEMP.
C
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538
550
575
600
625
649
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
PN 420
SIZES
15 thru 25
THREADED
(1)
291.4
291.4
291.4
291.4
291.4
291.4
281.0
271.2
266.2
243.0
202.4
140.9
95.2
62.8
38.2
26.9
291.4
291.4
291.0
287.8
281.9
280.0
279.7
277.8
275.0
267.7
261.8
251.5
237.4
204.0
160.0
136.2
116.8
80.0
52.2
34.2
21.7
291.4
291.4
291.4
291.4
291.4
291.4
281.0
271.2
266.2
243.0
202.4
140.9
95.2
61.9
36.4
24.8
291.4
291.4
291.0
287.8
281.9
280.0
279.7
277.8
275.0
267.7
261.8
251.5
237.4
201.1
152.6
126.2
108.3
74.3
48.4
31.6
20.0
431.0
431.0
431.0
431.0
431.0
431.0
415.6
401.0
393.5
359.4
299.5
208.6
141.0
93.3
57.6
41.4
431.0
431.0
430.5
426.0
417.0
414.2
413.8
410.8
407.2
396.2
387.2
372.1
351.2
304.0
242.5
209.7
PRESSURE (BAR)
PN 460
PN 760
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
462.1
462.1
462.1
462.1
462.1
462.1
445.7
429.9
421.8
385.4
321.2
223.6
151.3
100.1
62.0
44.8
462.1
462.1
461.4
456.7
447.1
443.9
443.4
440.4
436.4
424.7
415.1
398.8
376.5
326.6
261.6
226.3
194.0
132.8
86.9
56.3
35.9
462.1
462.1
462.1
462.1
462.1
462.1
445.7
429.9
421.8
385.4
321.2
223.6
151.3
98.1
57.7
39.7
462.1
462.1
461.4
456.7
447.1
443.9
443.4
440.4
436.4
424.7
415.1
398.8
376.5
319.1
242.1
200.2
171.6
117.5
76.9
49.8
31.7
775.9
775.9
775.9
775.9
775.9
775.9
748.1
721.8
708.4
646.9
539.2
375.7
254.0
171.0
110.0
82.4
775.9
775.9
774.8
766.5
750.7
745.6
744.8
739.3
732.8
713.1
697.3
670.1
632.3
556.9
465.0
416.1
357.0
244.7
159.7
103.5
65.9
775.9
775.9
775.9
775.9
775.9
775.9
748.1
721.8
708.4
646.9
539.2
375.7
254.0
165.0
97.2
66.6
775.9
775.9
774.8
766.5
750.7
745.6
744.8
739.3
732.8
713.1
697.3
670.1
632.3
535.5
406.2
336.0
288.2
197.5
129.0
83.6
53.1
1. Limited Class, Sizes DN 65 and smaller, all types ends except flanges. Threaded ends limited to Size DN 25 and smaller and 538 C maximum.
2. Special Class, Sizes DN 80 and DN 100, buttwelding ends only.
3. Permissible but not recommended for prolonged usage above approx. 427C.
4. Permissible but not recommended for use above 593C.
5. Shaded ratings may require special trim and packing, consult your Edward Valves sales representative for applications in these ranges.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A182
F91
NOTES:
TEMP.
F
-20 to 100
200
300
400
500
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
CLASS 2500
SIZES
1/2 thru 1
THREADED
(1)
4225
4225
4225
4225
4225
4225
4225
4130
4105
4055
3815
3380
2725
2555
2555
2290
1695
1095
4225
4225
4225
4225
4225
4225
4225
4130
4105
4055
3815
3380
2660
2370
2370
2125
1570
1015
6250
6250
6250
6250
6250
6250
6250
6110
6070
6000
5645
5000
4075
3925
PRESSURE (PSIG)
CLASS 2680
CLASS 4500
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
6700
6700
6700
6700
6700
6700
6700
6550
6505
6430
6050
5360
4385
4240
4240
3805
2805
1820
6700
6700
6700
6700
6700
6700
6700
6550
6505
6430
6050
5360
4215
3755
3755
3370
2485
1610
11250
11250
11250
11250
11250
11250
11250
10995
10930
10800
10160
9000
7555
7555
7555
7005
5180
3345
11250
11250
11250
11250
11250
11250
11250
10995
10930
10800
10160
9000
7070
6310
6310
5655
4180
2700
1. Limited Class, Sizes 2-1/2 and smaller, all types ends except flanges. Threaded ends limited to Size 1 and smaller and 1000 F maximum.
2. Special Class, Sizes 3 and 4, buttwelding ends only.
3. The 7555 repeats becuase ASME B16.34 rating rules do not permit increasing pressure ratings at higher pressures.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H5
Edward Valves
MATERIAL
A182
F91
NOTES:
H6
TEMP.
C
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538/550
575
600
625
649
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
PN 420
SIZES
15 thru 25
THREADED
(1)
291.4
291.4
291.4
291.4
291.4
291.4
291.4
289.8
284.6
283.0
279.9
265.8
240.9
204.2
181.6
176.2
170.0
148.1
111.1
75.5
291.4
291.4
291.4
291.4
291.4
291.4
291.4
289.8
284.6
283.0
279.9
265.8
240.9
201.3
172.6
163.4
157.7
137.4
102.9
70.0
431.0
431.0
431.0
431.0
431.0
431.0
431.0
428.7
421.0
418.4
414.1
393.2
356.4
304.0
275.4
270.1
PRESSURE (BAR)
PN 460
PN 760
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
462.1
462.1
462.1
462.1
462.1
462.1
462.1
459.6
451.3
448.6
443.9
421.5
382.1
326.4
297.1
292.8
282.5
246.1
184.2
125.3
462.1
462.1
462.1
462.1
462.1
462.1
462.1
459.6
451.3
448.4
443.8
421.4
382.0
319.1
273.6
259.0
249.9
217.8
162.9
111.0
775.9
775.9
775.9
775.9
775.9
775.9
775.9
771.6
757.6
753.4
745.5
707.8
641.5
556.9
521.0
521.0
508.1
452.9
339.5
230.7
775.9
775.9
775.9
775.9
775.9
775.9
775.9
771.6
757.6
753.4
745.4
707.8
641.5
535.5
459.3
435.2
419.8
365.6
274.0
186.2
1. Limited Class, Sizes DN 65 and smaller, all types ends except flanges. Threaded ends limited to Size DN 25 and smaller and 538 C maximum.
2. Special Class, Sizes DN 80 and DN 100, buttwelding ends only.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A182
F316
(3)
NOTES:
TEMP.
F
-20 to 100
200
300
400
500
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
1250
1300
1350
1400
1450
1500
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
CLASS 2500
SIZES
1/2 thru 1
THREADED
(1)
4225
3885
3515
3210
2990
2840
2775
2725
2680
2655
2625
2610
2580
2370
2370
2200
1795
1400
1115
885
730
570
440
315
4225
3885
3515
3210
2990
2840
2775
2725
2680
2655
2625
2610
2580
2370
2370
2145
1665
1300
1035
820
675
530
410
290
6250
5750
5200
4750
4430
4195
4105
4035
3965
3930
3885
3855
3815
3505
PRESSURE (PSIG)
CLASS 2680
CLASS 4500
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
6700
6165
5575
5090
4750
4495
4400
4325
4250
4215
4165
4135
4090
3755
3755
3545
2985
2340
1860
1470
1210
950
740
520
6700
6165
5575
5090
4750
4495
4400
4325
4250
4215
4165
4135
4090
3755
3755
3410
2640
2070
1645
1300
1070
840
655
460
11250
10350
9360
8550
7970
7555
7395
7265
7135
7070
6990
6945
6870
6310
6310
6115
5495
4300
3425
2705
2230
1755
1355
955
11250
10350
9360
8550
7970
7555
7395
7265
7135
7070
6990
6945
6870
6310
6310
5720
4435
3470
2765
2185
1800
1415
1095
770
1. Limited Class, Sizes 2-1/2 and smaller, all types ends except flanges. Threaded ends limited to Size 1 and smaller and 1000 F maximum.
2. Special Class, Sizes 3 and 4, buttwelding ends only.
3. Shaded ratings may require special trim and packing, consult your Edward Valves sales representative for applications in these ranges.
4. The 6310 repeats because ASME B16.34 rating rules do not permit increasing pressure ratings at higher pressures.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H7
Edward Valves
PN 290
MATERIAL
A182
F316
(3)
NOTES:
H8
TEMP.
C
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538/550
575
600
625
650
675
700
725
750
775
800
816
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
PN 420
SIZES
15 thru 25
THREADED
(1)
291.4
286.2
264.9
242.0
223.1
208.9
198.8
190.6
187.5
184.8
183.2
181.4
180.3
178.7
170.1
163.4
159.5
145.0
120.0
95.8
78.1
63.6
53.1
43.3
34.5
26.6
21.7
291.4
286.2
264.9
242.0
223.1
208.9
198.8
190.6
187.5
184.8
183.2
181.4
180.3
178.7
170.1
163.4
158.2
140.0
111.3
88.9
72.5
58.9
49.2
40.2
32.1
24.6
20.0
431.0
423.4
392.0
358.0
330.1
309.5
293.8
281.9
277.6
273.4
271.2
268.4
266.4
264.1
251.6
241.7
PRESSURE (BAR)
PN 460
PN 760
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
462.1
454.0
420.3
383.8
353.7
331.8
314.9
302.2
297.6
293.0
290.8
287.8
285.7
283.2
269.6
259.0
254.0
235.2
199.6
160.1
130.3
105.7
88.1
72.0
57.7
44.4
35.9
462.1
454.0
420.3
383.8
353.7
331.8
314.9
302.2
297.6
293.0
290.8
287.8
285.7
283.2
269.6
259.0
250.9
222.4
176.6
141.6
115.2
93.5
77.9
63.6
51.0
39.3
31.7
775.9
762.2
705.6
644.4
594.1
556.9
529.0
507.8
499.8
491.9
487.9
483.0
479.8
475.7
452.9
435.2
430.6
411.5
367.4
294.1
239.8
194.5
162.3
132.8
106.1
81.3
65.9
775.9
762.2
705.6
644.4
594.1
556.9
529.0
507.8
499.8
491.9
487.9
483.0
479.8
475.7
452.9
435.2
421.3
373.2
296.5
237.4
193.6
157.1
131.0
107.1
85.7
65.7
53.1
1. Limited Class, Sizes DN 65 and smaller, all types ends except flanges. Threaded ends limited to Size DN 25 and smaller and 538 C maximum.
2. Special Class, Sizes DN 80 and DN 100, buttwelding ends only.
3. Shaded ratings may require special trim and packing, consult your Edward Valves sales representative for applications in these ranges.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
A182
F347/F347H
(3) (4)
A182
F316L
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
CLASS 2500
SIZES
1/2 thru 1
THREADED
(1)
-20 to 100
200
300
400
500
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
1250
1300
1350
1400
1450
1500
4225
4035
3695
3475
3355
3230
3170
3110
3090
3065
3050
3030
2660
2370
2370
2325
2080
1300
940
705
525
420
315
260
4225
4035
3695
3475
3355
3230
3170
3110
3090
3065
3050
3030
2660
2370
2370
2270
1930
1205
870
655
485
390
290
240
-20 to 100
200
300
400
500
600
650
700
750
800
850
3770
3185
2850
2595
2400
2265
2195
2150
2100
2070
2020
3770
3185
2850
2595
2400
2265
2195
2150
2100
2070
2020
TEMP.
F
PRESSURE (PSIG)
CLASS 2680
CLASS 4500
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
SIZES
1/2 thru 2-1/2
(1)
SIZES
3&4
(2)
6250
5965
5465
5145
4965
4775
4690
4600
4570
4530
4510
4485
3930
3505
6700
6395
5860
5515
5320
5120
5030
4930
4900
4855
4835
4810
4215
3755
3755
3745
3455
2165
1560
1170
865
690
520
430
6700
6395
5860
5515
5320
5120
5030
4930
4900
4855
4835
4810
4215
3755
3755
3600
3060
1915
1380
1035
765
610
460
380
11,250
10,735
9835
9255
8935
8600
8440
8275
8230
8155
8115
8075
7070
6310
6310
6310
6310
3985
2870
2150
1590
1275
955
800
11,250
10,735
9835
9255
8935
8600
8440
8275
8230
8155
8115
8075
7070
6310
6310
6045
5145
3215
2315
1735
1285
1030
770
645
5570
4710
4215
3840
3550
3350
3250
3180
3110
3060
2990
5970
5050
4520
4115
3805
3590
3485
3410
3335
3280
3205
5970
5050
4520
4115
3805
3590
3485
3410
3335
3280
3205
10,030
8480
7585
6910
6390
6025
5850
5720
5595
5505
5385
10,030
8480
7585
6910
6390
6025
5850
5720
5595
5505
5385
NOTES:
1. Limited Class, Sizes 2-1/2 and smaller, all types ends except flanges. Threaded ends limited to Size 1 and smaller and 1000 F maximum.
2. Special Class, Sizes 3 and 4, buttwelding ends only.
3. Services in shaded areas may require special trim and packing, consult your Edward Valves sales representative for applications in these ranges.
4. A182 F347 material is not to be used over 1000F.
5. The 6310 repeats because ASME B16.34 rating rules do not permit increasing pressure ratings at higher pressures.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H9
Edward Valves
A182
F347/F347H
(3) (4)
A182
F316L
TEMP.
C
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538
550
575
600
625
650
675
700
725
750
775
800
816
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
454
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
PN 420
SIZES
15 thru 25
THREADED
(1)
291.4
288.5
275.5
254.5
240.9
232.9
225.2
217.6
214.3
213.0
211.5
210.5
209.3
192.6
172.6
163.4
163.4
162.4
156.3
135.9
88.7
66.3
51.2
39.4
31.6
25.1
20.1
17.9
260.0
251.1
216.9
196.2
180.4
167.9
158.8
150.6
147.8
144.7
142.9
139.9
139.3
291.4
288.5
275.5
254.5
240.9
232.9
225.2
217.6
214.3
213.0
211.5
210.5
209.3
192.6
172.6
163.4
163.4
161.1
150.9
126.1
82.2
61.4
47.5
36.5
29.3
23.2
18.5
16.6
260.0
251.1
216.9
196.2
180.4
167.9
158.8
150.6
147.8
144.7
142.9
139.9
139.3
431.0
426.7
407.2
376.5
356.6
344.6
333.0
322.0
317.0
315.1
312.6
311.3
309.8
284.8
255.2
241.7
384.1
371.1
320.7
290.2
266.9
248.4
234.9
223.0
218.6
214.3
211.2
207.0
206.2
PRESSURE (BAR)
PN 460
PN 760
SIZES
15 thru 65
(1)
SIZES
80 & 100
(2)
SIZES
15 thru 65
(1)
SIZES
80 &100
(2)
462.1
457.4
436.6
403.7
382.2
369.3
357.0
345.2
339.7
337.8
335.0
333.7
332.2
305.5
273.6
259.0
259.0
258.7
253.5
225.8
147.6
110.1
85.0
65.1
51.9
41.3
33.1
29.7
411.7
397.8
343.9
311.2
286.0
266.3
251.7
239.1
234.4
229.8
226.4
221.9
221.0
462.1
457.4
436.6
403.7
382.2
369.3
357.0
345.2
339.7
337.8
335.0
333.7
332.2
305.5
273.6
259.0
259.0
255.3
239.3
200.0
130.6
97.4
75.2
57.6
45.9
36.5
29.3
26.2
411.7
397.8
343.9
311.2
286.0
266.3
251.7
239.1
234.4
229.8
226.4
221.9
221.0
775.9
768.0
732.9
677.5
641.5
620.2
599.6
579.3
570.3
567.4
562.7
560.1
557.6
512.5
459.3
435.2
435.2
435.2
435.2
412.7
271.8
202.5
156.2
119.7
95.8
76.0
61.2
55.2
691.7
668.2
577.4
522.2
480.3
447.1
422.6
401.3
393.3
385.6
380.0
372.7
371.4
775.9
768.0
732.9
677.5
641.5
620.2
599.6
579.3
570.3
567.4
562.7
560.1
557.6
512.5
459.3
435.2
435.2
429.0
402.0
336.2
219.2
163.4
126.1
96.7
77.4
61.4
49.3
44.5
691.7
668.2
577.4
522.2
480.3
447.1
422.6
401.3
393.3
385.6
380.0
372.7
371.4
NOTES:
1. Limited Class, Sizes DN 65 and smaller, all types ends except flanges. Threaded ends limited to Size DN 25 and smaller and 538 C maximum.
2. Special Class, Sizes DN 80 and DN 100, buttwelding ends only.
3. Services in shaded areas may require special trim and packing, consult your Edward Valves sales representative for applications in these ranges.
4. A182 F347 material is not to be used over 538C.
H10
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
TEMPERATURE
F
PRESSURE (PSIG)
A-105 (1)
F-11
-20 to 100
200
300
400
500
600
650
700
750
800
850
900
950
1000
1480
1350
1315
1270
1200
1095
1075
1065
1010
825
535
345
205
105
1500
1500
1445
1385
1330
1210
1175
1135
1065
1015
975
900
640
430
-20 to 100
200
300
400
500
600
650
700
750
800
850
900
950
1000
2000
2000
2000
2000
2000
1900
1865
1850
1680
1375
895
575
350
180
2000
2000
2000
2000
2000
2000
2000
1955
1945
1920
1805
1565
1070
745
1. Permissible but not recommended for prolonged use at temperatures above approx. 800F.
2. Shaded ratings exceed those of Edward Valves. Consult your Edward Valves sales representative for applications in these ranges.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H11
Edward Valves
TEMPERATURE
F
-20 to 100
200
300
400
500
600
650
700
750
800
850
900
950
975
PRESSURE (PSIG)
A-105 (1)
3600
3375
3280
3170
2995
2735
2560
2350
2130
1830
1500
F-11
3600
3510
3365
3290
3130
2770
2595
2420
2255
2085
1920
1750
1585
1500
1. Permissible but not recommended for prolonged use at temperatures above approx. 800F.
2. Series 1500 components are designed and rated to Edward Valves standards. See paragraph 3.2, pages G59-G60, for additional information.
3. Shaded ratings exceed those of Edward Valves. Consult your Edward Valves sales representative for applications in these ranges.
H12
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
PRESSURE (BAR)
A-105 (1)
F-11
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538
102.1
100.1
92.8
90.6
87.8
83.6
77.5
74.0
72.9
69.1
57.7
40.1
27.2
17.6
10.4
7.2
103.4
103.4
103.0
99.6
95.8
92.4
85.8
80.4
77.6
73.3
70.2
67.7
63.4
50.6
36.3
29.7
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538
137.9
137.9
137.9
137.9
137.9
137.9
133.0
128.4
125.9
115.0
96.1
67.0
45.4
29.7
17.8
12.4
137.9
137.9
137.9
137.9
137.9
137.9
137.9
137.2
134.7
134.1
132.5
125.8
112.2
86.1
61.7
51.4
1. Permissible but not recommended for prolonged use at temperatures above approx. 427C.
2. Shaded ratings exceed those of Edward Valves. Consult your Edward Valves sales representative for applications in these ranges.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H13
Edward Valves
PRESSURE (BAR)
A-105 (1)
248.3
244.9
232.0
226.1
219.2
208.7
193.6
173.1
159.9
146.1
127.4
103.4
F-11
248.3
246.9
240.9
232.0
227.3
217.8
198.0
176.1
165.3
155.0
144.5
134.2
123.7
113.4
103.4
1. Permissible but not recommended for prolonged use at temperatures above approx. 427C.
2. Series 1500 components are designed and rated to Edward Valves standards. See paragraph 3.2, pages G59-G60, for additional information.
3. Shaded ratings exceed those of Edward Valves. Consult your Edward Valves sales representative for applications in these ranges.
H14
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
ASTM A216-WCB
TEMPERATURE
F
300
400
600
700
PRESSURE (PSIG)
900
1100
1500
1800
2500
2900
4500**
-20 to 100
740
990
1480
1725
2220
2715
3705
4445
6170
7160
11110
200
675
900
1350
1575
2025
2475
3375
4050
5625
6525
10120
300
655
875
1315
1535
1970
2405
3280
3935
5470
6345
9845
400
635
845
1270
1480
1900
2325
3170
3805
5280
6125
9505
500
600
800
1200
1400
1795
2195
2995
3595
4990
5790
8980
600
550
730
1095
1275
1640
2005
2735
3285
4560
5290
8210
STANDARD CLASS
650
535
715
1075
1255
1610
1970
2685
3220
4475
5190
8055
(1) (2)
700
535
710
1065
1245
1600
1955
2665
3200
4440
5150
7990
750
505
670
1010
1175
1510
1845
2520
3025
4200
4870
7560
800
410
550
825
960
1235
1510
2060
2470
3430
3980
6170
850
270
355
535
625
805
985
1340
1605
2230
2585
4010
900
170
230
345
400
515
630
860
1030
1430
1660
2570
950
105
140
205
240
310
380
515
620
860
995
1545
1000
50
70
105
120
155
190
260
310
430
500
770
-20 to 100
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
200
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
300
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
400
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
500
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
ASTM A216-WCB
600
715
950
1425
1665
2140
2615
3565
4280
5940
6890
10690
SPECIAL CLASS
650
700
935
1400
1635
2100
2565
3495
4195
5825
6755
10485
(1) (2)
700
695
925
1390
1620
2080
2545
3470
4165
5780
6705
10405
750
630
840
1260
1470
1890
2310
3150
3780
5250
6090
9450
800
515
685
1030
1200
1545
1885
2570
3085
4285
4970
7715
850
335
445
670
780
1005
1225
1670
2005
2785
3230
5015
900
215
285
430
500
645
785
1070
1285
1785
2070
3215
950
130
170
260
300
385
470
645
775
1070
1240
1930
1000
65
85
130
150
195
235
320
385
535
620
965
Note: Flanged End Valve ratings are limited to standard class only.
1. Permissible but not recommended for prolonged use at temperatures above approx. 800F.
2. Shaded ratings exceed those of standard Edward Valves. Consult your Edward Valves sales representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
** Series 4500 rated Cast Steel Valves do not comply with ASME Class 4500 ratings. Consult your Edward Valves sales representative for pressure temperature ratings of these
valves. See paragraph 3.2, pages G59-G60, for additional information.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H15
Edward Valves
PN 50
PN 68
PN 110
PN 120
PN 260
PN 310
PN 420
PN 490
-29 to 38
51.0
68.3
102.1
119.0
153.1
187.2
255.5
306.6
425.5
493.8
766.2
50
50.0
66.9
100.1
116.7
150.1
183.6
250.5
300.6
417.2
484.2
751.2
100
46.4
61.9
92.8
108.3
139.2
170.1
232.0
278.4
386.6
448.5
695.7
150
45.1
60.3
90.6
105.8
135.8
165.8
226.1
271.2
377.0
437.3
678.5
200
43.9
58.4
87.8
102.4
131.4
160.8
219.2
263.1
365.2
423.6
657.4
ASTM A216-WCB
250
41.8
55.7
83.6
97.5
125.1
153.0
208.7
250.5
347.7
403.5
625.8
STANDARD CLASS
300
38.9
51.7
77.5
90.3
116.1
141.9
193.6
232.5
322.8
374.5
581.1
(1) (2)
350
36.9
49.2
74.0
86.4
110.9
135.6
184.8
221.7
308.0
357.3
554.4
375
36.6
48.6
72.9
85.2
109.5
133.8
182.4
219.0
303.9
352.5
546.9
400
34.6
45.9
69.1
80.4
103.4
126.3
172.5
207.1
287.5
333.4
517.5
425
28.7
38.4
57.7
67.1
86.3
105.5
144.0
172.6
239.7
278.2
431.3
450
20.2
26.6
40.1
46.8
60.3
73.7
100.4
120.2
167.0
193.7
300.4
475
13.5
18.1
27.2
31.6
40.7
49.8
67.9
81.3
113.0
131.1
203.1
500
8.9
11.9
17.6
20.5
26.5
32.4
44.1
52.9
73.5
85.1
132.0
525
5.2
7.0
10.4
12.1
15.6
19.1
26.0
31.2
43.3
50.2
77.7
538
3.4
4.8
7.2
8.3
10.7
13.1
17.9
21.4
29.7
34.5
53.1
RATING
PRESSURE (BAR)
PN 150
PN 190
PN 760
-29 to 38
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
50
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
100
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
150
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
200
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
ASTM A216-WCB
250
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
SPECIAL CLASS
300
50.0
66.5
99.7
116.5
149.7
183.0
249.4
299.4
415.6
482.1
748.1
(1) (2)
350
48.2
64.3
96.4
112.5
144.5
176.6
240.6
288.8
401.0
465.0
721.8
375
47.3
63.0
94.6
110.3
141.6
173.2
236.2
283.5
393.5
456.5
708.4
400
43.1
57.5
86.3
100.6
129.4
158.1
215.6
258.8
359.4
416.9
646.9
425
36.0
47.9
72.0
83.9
108.0
131.8
179.6
215.6
299.5
347.4
539.2
450
25.1
33.3
50.2
58.4
75.3
91.8
125.1
150.2
208.6
242.0
375.7
475
17.0
22.5
34.0
39.5
50.9
62.0
84.6
101.5
141.0
163.6
254.0
500
11.1
14.6
22.2
25.7
33.0
40.2
55.0
66.1
91.5
106.1
165.0
525
6.5
8.6
13.1
15.1
19.5
23.7
32.4
38.9
53.9
62.4
97.2
538
4.5
5.9
9.0
10.3
13.4
16.2
22.1
26.6
36.9
42.8
66.6
1. Permissible but not recommended for prolonged use at temperatures above approx. 427C.
2. Shaded ratings exceed those of standard Edward Valves. Consult your Edward Valves sales representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
H16
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
400
600
700
PRESSURE (PSIG)
900
1100
1500
1800
2500
2900
-20 to 100
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
200
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
300
720
965
1445
1685
2165
2645
3610
4330
6015
6980
10830
400
695
925
1385
1615
2080
2540
3465
4160
5775
6700
10400
500
665
885
1330
1550
1995
2440
3325
3990
5540
6425
9965
ASTM A-217-WC6
600
605
805
1210
1410
1815
2220
3025
3630
5040
5845
9070
STANDARD CLASS
650
590
785
1175
1370
1765
2155
2940
3530
4905
5690
8825
(1)
700
570
755
1135
1325
1705
2085
2840
3405
4730
5485
8515
750
530
710
1065
1240
1595
1950
2660
3190
4430
5140
7970
800
510
675
1015
1185
1525
1865
2540
3045
4230
4905
7610
850
485
650
975
1135
1460
1785
2435
2925
4060
4710
7305
900
450
600
900
1050
1350
1650
2245
2695
3745
4345
6740
950
320
425
640
745
955
1170
1595
1915
2655
3080
4785
1000
215
290
430
505
650
795
1080
1295
1800
2090
3240
1050
145
190
290
335
430
525
720
865
1200
1390
2160
1100
95
130
190
225
290
355
480
575
800
930
1440
-20 to 100
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
200
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
300
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
400
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
500
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
ASTM A-217-WC6
600
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
SPECIAL CLASS
650
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
(1)
700
735
980
1465
1710
2200
2690
3665
4400
6110
7085
10995
750
730
970
1460
1700
2185
2670
3645
4375
6070
7040
10930
800
720
960
1440
1680
2160
2640
3600
4320
6000
3960
10800
850
680
905
1355
1580
2030
2480
3385
4065
5645
6550
10160
900
585
785
1175
1370
1760
2150
2935
3525
4895
5675
8805
950
400
530
795
930
1195
1460
1995
2395
3320
3850
5980
1000
270
360
540
630
810
990
1350
1620
2250
2610
4050
1050
180
240
360
420
540
660
900
1080
1500
1740
2700
1100
120
160
240
280
360
440
600
720
1000
1160
1800
RATING
TEMPERATURE
F
4500**
Note: Flanged End Valve ratings are limited to standard class only and terminate at 1000F.
1. Shaded ratings may require special trim and packing. Consult your Edward Valves sales representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
** Series 4500 rated Cast Steel Valves do not comply with ASME Class 4500 ratings. Consult your Edward Valves sales representative for pressure temperature
ratings of these valves. See paragraph 3.2, page G59-G60, for additional information.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H17
Edward Valves
TEMPERATURE
C
PN 50
PN 68
PN 110
PN 120
PN 260
PN 310
PN 420
PN 490
-29 to 38
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
50
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
100
51.5
68.7
103.0
120.2
154.5
188.8
257.5
308.9
429.1
497.8
772.4
150
49.6
66.5
99.6
116.1
149.2
182.3
248.8
298.4
414.5
481.0
746.3
200
48.1
64.0
95.8
111.8
143.9
175.8
239.8
287.8
399.6
463.6
719.6
ASTM A-217-WC6
250
46.2
61.5
92.4
107.7
138.6
169.5
231.0
277.3
385.0
446.5
692.6
STANDARD CLASS
300
42.9
57.1
85.8
99.9
128.6
157.4
214.4
257.3
357.2
414.3
642.8
(1)
ASTM A-217-WC6
PN 760
350
40.4
53.6
80.4
93.7
120.7
147.5
201.1
241.4
335.4
389.0
603.5
375
38.9
51.6
77.6
90.6
116.5
142.5
194.1
232.8
323.3
374.9
582.0
400
36.5
48.9
73.3
85.4
109.8
134.2
183.1
219.6
305.0
353.8
548.7
425
35.3
46.7
70.2
82.0
105.5
129.0
175.7
210.6
292.6
339.2
526.3
450
33.7
45.1
67.7
78.8
101.4
124.0
169.1
203.0
281.9
327.0
507.2
475
31.7
42.3
63.4
73.9
95.1
116.2
158.2
190.0
263.9
306.2
475.0
500
25.3
33.7
50.6
59.0
75.7
92.6
126.1
151.4
210.2
243.8
378.5
525
18.2
24.3
36.3
42.4
54.5
66.7
90.8
109.0
151.3
175.5
272.5
538
14.8
19.9
29.6
34.7
44.7
54.7
74.3
89.1
123.8
143.8
222.9
550
12.7
17.0
25.4
29.7
38.2
46.6
63.6
76.3
105.9
122.9
190.7
575
8.8
11.7
17.7
20.5
26.4
32.2
44.0
52.9
73.4
85.1
132.1
593
6.6
9.0
13.1
15.5
20.0
24.5
33.1
39.7
55.2
64.1
99.3
-29 to 38
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
50
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
100
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
150
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
200
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
250
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
STANDARD CLASS
300
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
(1)
350
51.5
68.6
102.9
120.0
154.3
188.7
257.2
308.7
428.7
497.3
771.6
375
50.6
67.5
101.0
117.8
151.6
185.3
252.6
303.2
421.0
488.2
757.6
400
50.3
66.9
100.6
117.2
150.6
184.1
251.3
301.6
418.4
485.3
753.4
425
49.7
66.2
99.4
115.9
149.1
182.2
248.5
298.2
414.1
480.3
745.4
450
47.3
63.0
94.4
110.1
141.4
172.8
235.8
283.2
393.2
456.2
707.8
475
42.0
56.3
84.3
98.2
126.2
154.2
210.5
252.8
351.0
407.1
631.5
500
32.2
42.9
64.3
75.1
96.4
117.8
160.9
193.2
268.1
310.8
482.6
525
22.7
30.2
45.3
53.0
68.1
83.2
113.6
136.3
189.1
219.3
340.5
538
18.6
24.8
37.1
43.3
55.7
68.1
92.9
111.4
154.8
179.5
278.6
550
15.9
21.2
31.8
37.1
47.7
58.3
79.4
95.3
132.4
153.6
238.3
575
11.0
14.7
22.0
25.7
33.0
40.4
55.0
66.0
91.7
106.4
165.1
593
8.3
11.0
16.6
19.3
24.8
30.3
41.4
49.7
69.0
80.0
124.1
1. Shaded ratings may require special trim and packing. Consult your Edward Valves sales representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
H18
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
TEMPERATURE
F
1500
1800
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
200
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
300
730
970
1455
1700
2185
2670
3640
4370
6070
7040
10925
400
705
940
1410
1645
2115
2585
3530
4235
5880
6820
10585
500
665
885
1330
1550
1995
2440
3325
3990
5540
6425
9965
ASTM A217-WC9
600
605
805
1210
1410
1815
2220
3025
3630
5040
5845
9070
STANDARD CLASS
650
590
785
1175
1370
1765
2155
2940
3530
4905
5690
8825
700
570
755
1135
1325
1705
2085
2840
3405
4730
5485
8515
750
530
710
1065
1240
1595
1950
2660
3190
4430
5140
7970
800
510
675
1015
1185
1525
1865
2540
3045
4230
4905
7610
850
485
650
975
1135
1460
1785
2435
2925
4060
4710
7305
900
450
600
900
1050
1350
1650
2245
2695
3745
4345
6740
950
375
505
755
880
1130
1380
1885
2265
3145
3650
5665
1000
260
345
520
605
780
955
1305
1565
2170
2520
3910
1050
175
235
350
410
525
640
875
1050
1455
1690
2625
1100
110
145
220
255
330
405
550
660
915
1060
1645
-20 to 100
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
200
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
300
740
990
1485
1730
2225
2720
3705
4450
6180
7170
11120
400
725
965
1450
1690
2175
2655
3620
4345
6035
7000
10865
500
720
960
1440
1680
2160
2640
3600
4320
6000
6960
10800
600
720
960
1440
1680
2160
2640
3600
4320
6000
6960
10800
SPECIAL CLASS
400
600
700
PRESSURE (PSIG)
900
1100
-20 to 100
ASTM A217-WC9
300
2500
2900
4500**
650
715
955
1430
1670
2145
2625
3580
4295
5965
6920
10735
700
710
955
1425
1660
2135
2610
3555
4270
5930
6880
10670
750
690
920
1380
1610
2070
2530
3450
4140
5750
6670
10350
800
675
895
1345
1570
2020
2470
3365
4035
5605
6505
10095
850
645
855
1285
1500
1930
2360
3215
3855
5355
6215
9645
900
600
800
1200
1400
1800
2200
3000
3600
5000
5800
9000
950
470
630
945
1100
1415
1730
2355
2830
3930
4560
7070
1000
325
435
650
760
975
1195
1630
1955
2715
3150
4885
1050
220
290
435
510
655
800
1095
1315
1820
2110
3280
1100
135
185
275
320
410
500
685
825
1145
1325
2055
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
** Series 4500 rated Cast Steel Valves do not comply with ASME Class 4500 ratings. Consult your Edward Valves sales representative for pressure temperature ratings of these
valves. See paragraph 3.2, page G59-G60, for additional information.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H19
Edward Valves
TEMPERATURE
C
PN 260
PN 310
PN 420
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
50
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
100
51.6
68.7
103.1
120.3
154.6
189.0
257.7
309.3
429.5
498.3
773.2
150
50.3
66.9
100.3
117.2
150.6
184.0
250.9
301.2
418.4
485.2
753.0
200
48.8
65.0
97.5
113.8
146.2
178.7
244.1
292.8
406.6
471.6
731.9
ASTM A-217-WC9
250
46.4
61.7
92.7
108.1
139.1
170.1
231.9
278.2
386.3
448.0
694.9
STANDARD CLASS
300
42.9
57.1
85.8
99.9
128.6
157.4
214.4
257.3
357.2
414.3
642.8
350
40.4
53.6
80.4
93.7
120.7
147.5
201.1
241.4
335.4
389.0
603.5
375
38.9
51.6
77.6
90.6
116.5
142.5
194.1
232.8
323.3
374.9
582.0
400
36.5
48.9
73.3
85.4
109.8
134.2
183.1
219.6
305.0
353.8
548.7
425
35.3
46.7
70.2
82.0
105.5
129.0
175.7
210.6
292.6
339.2
526.3
450
33.7
45.1
67.7
78.8
101.4
124.0
169.1
203.0
281.9
327.0
507.2
475
31.7
42.3
63.4
73.9
95.1
116.2
158.2
190.0
263.9
306.2
475.0
500
27.7
37.2
55.7
64.9
83.4
101.9
138.9
166.9
231.8
269.0
417.4
525
21.6
28.9
43.3
50.4
64.9
79.3
108.4
130.1
180.6
209.6
325.3
538
17.9
23.7
35.8
41.6
53.7
65.7
89.8
107.6
149.3
173.3
268.9
550
15.4
20.5
30.7
35.8
46.1
56.3
77.0
92.3
128.0
148.6
230.7
575
10.5
14.1
21.1
24.6
31.6
38.6
52.7
63.3
87.7
101.8
158.1
593
7.6
10.0
15.2
17.6
22.8
27.9
37.9
45.5
63.1
73.1
113.4
STANDARD CLASS
PN 68
PN 110
PRESSURE (BAR)
PN 120
PN 150
PN 190
-29 to 38
ASTM A-217-WC9
PN 50
PN 760
-29 to 38
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
50
51.7
69.0
103.4
120.7
155.2
189.7
258.6
310.3
431.0
500.0
775.9
100
51.6
68.9
103.3
120.5
155.0
189.4
258.2
309.9
430.5
499.3
774.8
150
51.0
68.2
102.4
119.3
153.4
187.5
255.4
306.8
426.0
494.2
766.5
200
50.1
66.7
100.2
116.8
150.3
183.5
250.1
300.2
417.0
483.7
750.7
250
49.7
66.3
99.4
116.0
149.2
182.3
248.5
298.2
414.2
480.5
745.6
300
49.7
66.2
99.3
115.9
149.0
182.1
248.3
297.9
413.8
480.0
744.8
350
49.2
65.9
98.5
115.0
147.8
180.8
246.5
295.8
410.8
476.6
739.3
375
48.8
65.5
97.8
114.0
146.6
179.2
244.2
293.2
407.2
472.5
732.8
400
47.5
63.4
95.1
110.9
142.6
174.3
237.7
285.2
396.2
459.5
713.1
425
46.6
61.8
92.9
108.4
139.5
170.6
232.4
278.7
387.2
449.3
697.3
450
44.8
59.4
89.3
104.2
134.1
164.0
223.4
267.8
372.1
431.8
670.1
475
42.2
56.2
84.3
98.3
126.5
154.6
210.8
252.8
351.2
407.4
632.3
500
35.6
47.7
71.5
83.3
107.1
131.0
178.4
214.3
297.6
345.3
535.5
525
27.0
36.2
54.2
63.2
81.2
99.4
135.4
162.6
225.8
262.0
406.2
538
22.4
29.9
44.7
52.3
67.1
82.2
112.1
134.5
186.7
216.7
336.0
550
19.2
25.6
38.3
44.8
57.5
70.4
96.2
115.4
160.1
185.7
288.2
575
13.2
17.5
26.2
30.7
39.4
48.1
65.9
79.2
109.7
127.1
197.5
593
9.3
12.8
19.0
22.1
28.3
34.5
47.2
56.9
79.0
91.4
141.7
1. Shaded ratings may require special trim and packing. Consult your Edward Valves sales representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
H20
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
300
400
600
700
PRESSURE (PSIG)
900
1100
1500
1800
2500
2900
4500**
-20 to 100
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
200
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
300
730
970
1455
1700
2185
2670
3640
4370
6070
7040
10925
400
705
940
1410
1645
2115
2585
3530
4235
5880
6820
10585
500
665
885
1330
1550
1995
2440
3325
3990
5540
6425
9965
ASTM A217-C12A
600
605
805
1210
1410
1815
2220
3025
3630
5040
5845
9070
STANDARD CLASS
650
590
785
1175
1370
1765
2155
2940
3530
4905
5690
8825
700
570
755
1135
1325
1705
2085
2840
3405
4730
5485
8515
750
530
710
1065
1240
1595
1950
2660
3190
4430
5140
7970
800
510
675
1015
1185
1525
1865
2540
3045
4230
4905
7610
850
485
650
975
1135
1460
1785
2435
2925
4060
4710
7305
900
450
600
900
1050
1350
1650
2245
2695
3745
4345
6740
950
385
515
775
905
1160
1415
1930
2315
3220
3735
5795
1000
365
485
725
845
1090
1335
1820
2185
3030
3515
5450
1050
360
480
720
840
1080
1320
1800
2160
3000
3480
5400
1100
300
400
605
705
905
1105
1510
1810
2515
2915
4525
1150
225
295
445
520
670
820
1115
1335
1855
2155
3345
1200
145
190
290
335
430
525
720
865
1200
1390
2160
-20 to 100
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
200
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
300
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
400
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
500
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
ASTM A217-C12A
600
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
SPECIAL CLASS
650
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
700
735
980
1465
1710
2200
2690
3665
4400
6110
7085
10995
750
730
970
1460
1700
2185
2670
3645
4375
6070
7040
10930
800
720
960
1440
1680
2160
2640
3600
4320
6000
6960
10800
850
680
905
1355
1580
2030
2480
3385
4065
5645
6550
10160
900
600
800
1200
1400
1800
2200
3000
3600
5000
5800
9000
950
470
630
945
1100
1415
1730
2360
2830
3930
4560
7070
1000
420
560
840
980
1260
1540
2105
2525
3505
4065
6310
1050
420
560
840
980
1260
1540
2105
2525
3505
4065
6310
1100
375
505
755
880
1130
1380
1885
2265
3145
3645
5655
1150
280
370
555
650
835
1020
1395
1675
2320
2690
4180
1200
180
240
360
420
540
660
900
1080
1500
1740
2700
RATING
Shaded ratings may require special trim or packing. Consult your Edward Valves sales representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
** Series 4500 rated Cast Steel Valves do not comply with ASME Class 4500 ratings. Consult your Edward Valves sales representative for pressure temperature
ratings of these valves. See paragraph 3.2, page G59-G60, for additional information.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H21
Edward Valves
ASTM A-217-C12A
STANDARD CLASS
ASTM A-217-C12A
SPECIAL CLASS
TEMPERATURE
C
PN 50
PN 68
PN 110
PN 260
PN 310
PN 420
PN 490
PN 760
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538
550
575
600
625
649
51.7
51.7
51.6
50.3
48.8
46.4
42.9
40.4
38.9
36.5
35.3
33.7
31.7
28.2
25.8
25.2
25.0
23.4
19.4
14.7
10.0
69.0
69.0
68.7
66.9
65.0
61.7
51.7
53.6
51.6
48.9
46.7
45.1
42.3
37.6
34.4
33.4
33.3
31.2
25.8
19.3
13.1
103.4
103.4
103.1
100.3
97.5
92.7
85.8
80.4
77.6
73.3
70.2
67.7
63.4
56.6
51.6
50.0
49.8
47.0
39.1
29.2
20.0
120.7
120.7
120.3
117.2
113.8
108.1
99.9
93.7
90.6
85.4
82.0
78.8
73.9
66.0
60.2
58.3
58.1
54.8
45.6
34.1
23.1
155.2
155.2
154.6
150.6
146.2
139.1
128.6
120.7
116.5
109.8
105.5
101.4
95.1
84.7
77.4
75.2
74.9
70.4
58.5
43.9
29.7
189.7
189.7
189.0
184.0
178.7
170.1
157.4
147.5
142.5
134.2
129.0
124.0
116.2
103.4
94.6
92.1
91.6
86.0
71.5
53.7
36.2
258.6
258.6
257.7
250.9
244.1
231.9
214.4
201.1
194.1
183.1
175.7
169.1
158.2
140.9
129.0
125.5
124.9
117.3
97.6
73.1
49.7
291.4
291.4
290.3
282.6
274.8
261.1
241.6
226.7
218.7
206.2
197.8
190.6
178.3
158.8
145.3
141.4
140.8
132.3
109.9
82.3
55.9
431.0
431.0
429.5
418.4
406.6
386.3
357.2
335.4
323.3
305.0
292.6
281.9
263.9
235.1
215.0
208.9
208.1
195.5
162.5
121.6
82.8
500.0
500.0
498.3
485.2
471.6
448.0
414.3
389.0
374.9
353.8
339.2
327.0
306.2
272.7
249.4
242.4
241.4
226.8
188.5
141.2
95.9
775.9
775.9
773.2
753.0
731.9
694.9
642.8
603.5
582.0
548.7
526.3
507.2
475.0
423.1
386.8
375.8
374.3
351.9
292.5
219.2
149.0
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538
550
575
600
625
649
51.7
51.7
51.7
51.7
51.7
51.7
51.7
51.5
50.6
50.3
49.7
47.3
42.8
35.6
30.6
29.0
29.0
27.9
24.3
18.3
12.4
69.0
69.0
69.0
69.0
69.0
69.0
69.0
68.6
67.5
66.9
66.2
63.0
57.1
47.7
40.8
38.6
38.6
37.3
32.6
24.3
16.6
103.4
103.4
103.4
103.4
103.4
103.4
103.4
102.9
101.0
100.6
99.4
94.4
85.5
71.5
61.3
57.9
57.9
55.9
48.8
36.4
24.8
120.7
120.7
120.7
120.7
120.7
120.7
120.7
120.0
117.8
117.2
115.9
110.1
99.8
83.3
71.4
67.6
67.6
65.2
56.9
42.6
29.0
155.2
155.2
155.2
155.2
155.2
155.2
155.2
154.3
151.6
150.6
149.1
141.4
128.3
107.1
91.8
86.9
86.9
83.8
73.0
54.7
37.2
189.7
189.7
189.7
189.7
189.7
189.7
189.7
188.7
185.3
184.1
182.2
172.8
156.7
131.0
112.2
106.2
106.2
102.5
89.2
66.9
45.5
258.6
258.6
258.6
258.6
258.6
258.6
258.6
257.2
252.6
251.3
248.5
235.8
213.8
178.6
153.3
145.2
145.2
140.0
121.9
91.4
62.1
310.3
310.3
310.3
310.3
310.3
310.3
310.3
308.7
303.2
301.6
298.2
283.2
256.6
214.3
183.8
174.1
174.1
168.0
146.4
109.8
74.5
431.0
431.0
431.0
431.0
431.0
431.0
431.0
428.7
421.0
418.4
414.1
393.2
356.4
297.6
255.2
241.7
241.7
233.3
203.2
152.1
103.4
500.0
500.0
500.0
500.0
500.0
500.0
500.0
497.3
488.2
485.3
480.3
456.2
413.4
345.3
296.0
280.3
280.3
270.5
235.6
176.3
120.0
775.9
775.9
775.9
775.9
775.9
775.9
775.9
771.6
757.6
753.4
745.4
707.8
641.5
535.5
459.3
435.2
435.2
419.8
365.6
274.0
186.2
PN 120
PRESSURE (BAR)
PN 150
PN 190
Shaded ratings may require special trim or packing. Consult your Edward Valves sales representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
H22
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
ASTM A351-CF8M
TEMPERATURE
F
300
400
600
700
PRESSURE (PSIG)
900
1100
1500
1800
2500
2900
4500**
-20 to 100
720
960
1440
1680
2160
2640
3600
4320
6000
6960
10800
200
620
825
1240
1445
1860
2270
3095
3715
5160
5985
9290
300
560
745
1120
1305
1680
2050
2795
3355
4660
5405
8390
400
515
685
1025
1195
1540
1885
2570
3085
4280
4965
7705
500
480
635
955
1115
1435
1755
2390
2865
3980
4615
7165
600
450
600
900
1050
1355
1655
2255
2705
3760
4360
6770
STANDARD CLASS
650
445
590
890
1035
1330
1625
2220
2665
3700
4290
6660
(1)
700
430
580
870
1015
1305
1595
2170
2605
3620
4200
6515
750
425
570
855
995
1280
1565
2135
2565
3560
4130
6410
800
420
565
845
985
1265
1545
2110
2535
3520
4085
6335
850
420
555
835
975
1255
1535
2090
2505
3480
4035
6265
900
415
555
830
970
1245
1520
2075
2490
3460
4015
6230
950
385
515
775
905
1160
1415
1930
2315
3220
3735
5795
1000
350
465
700
815
1050
1285
1750
2100
2915
3380
5245
1050
345
460
685
800
1030
1260
1720
2065
2865
3325
5155
1100
305
405
610
710
915
1120
1525
1830
2545
2950
4575
1150
235
315
475
555
710
870
1185
1420
1970
2285
3550
1200
185
245
370
430
555
680
925
1110
1545
1790
2775
1250
145
195
295
345
440
540
735
885
1230
1425
2210
1300
115
155
235
275
350
430
585
700
970
1125
1750
1350
95
130
190
225
290
355
480
575
800
930
1440
1400
75
100
150
175
225
275
380
455
630
730
1130
1450
60
80
115
135
175
215
290
350
485
565
875
1500
40
55
85
100
125
150
205
245
345
400
620
1. Shaded ratings may require special trim and packing, consult your Edward Valves representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
** Series 4500 rated Cast Steel Valves do not comply with ASME Class 4500 ratings. Consult your Edward Valves sales representative for pressure temperature ratings of these
valves. See paragraph 3.2, page G59-G60, for additional information.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H23
Edward Valves
300
400
600
700
900
1800
2500
2900
-20 to 100
750
1000
1500
1750
2250
2750
3750
4500
6250
7250
11250
200
690
920
1380
1610
2070
2530
3450
4140
5750
6670
10350
300
625
830
1250
1455
1870
2285
3120
3745
5200
6030
9360
400
570
760
1140
1330
1710
2090
2850
3420
4750
5510
8550
500
530
710
1065
1240
1595
1950
2655
3190
4430
5140
7970
ASTM A351-CF8M
600
505
670
1005
1175
1510
1845
2520
3025
4195
4865
7555
SPECIAL CLASS
650
495
655
985
1150
1480
1810
2465
2955
4105
4765
7395
(1)
700
485
645
970
1130
1455
1775
2420
2905
4035
4680
7265
750
475
635
950
1110
1425
1745
2380
2855
3965
4600
7135
800
470
630
945
1100
1415
1730
2355
2830
3930
4560
7070
850
465
620
930
1085
1400
1710
2330
2795
3885
4505
6990
900
465
615
925
1080
1390
1700
2315
2775
3855
4475
6945
950
460
610
915
1070
1375
1680
2290
2750
3815
4425
6870
1000
420
560
840
980
1260
1540
2105
2525
3505
4065
6310
1050
420
560
840
980
1260
1540
2105
2525
3505
4065
6310
1100
380
510
765
890
1145
1400
1905
2290
3180
3690
5720
1150
295
395
590
690
885
1085
1480
1775
2465
2860
4435
1200
230
310
465
540
695
850
1155
1390
1930
2240
3470
1250
185
245
370
430
555
675
920
1105
1535
1780
2765
1300
145
195
290
340
435
535
730
875
1215
1410
2185
1350
120
160
240
280
360
440
600
720
1000
1160
1800
1400
95
125
190
220
285
345
470
565
785
910
1415
1450
75
100
145
170
220
270
365
440
610
705
1095
1500
50
70
105
120
155
190
260
310
430
500
770
RATING
PRESSURE (PSIG)
1100
1500
4500**
1. Shaded ratings may require special trim and packing, consult your Edward Valves representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
** Series 4500 rated Cast Steel Valves do not comply with ASME Class 4500 ratings. Consult your Edward Valves sales representative for pressure temperature ratings of these
valves. See paragraph 3.2, page G59-G60, for additional information.
H24
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
ASTM A-315-CF8M
STANDARD CLASS
(1)
TEMPERATURE
C
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538
550
575
600
625
650
675
700
725
750
775
800
816
PN 50
PN 68
PN 110
PN 120
49.7
48.1
42.3
38.6
35.8
33.5
31.6
30.4
29.6
29.3
29.0
29.0
28.7
27.3
25.2
24.1
24.0
22.9
19.9
15.7
12.6
10.2
8.3
6.9
5.7
4.6
3.5
2.8
66.2
64.2
56.2
51.3
47.6
44.4
42.1
40.5
39.9
39.3
39.0
38.4
38.3
36.5
33.7
32.1
31.9
30.4
26.4
21.0
16.8
13.7
11.1
9.4
7.6
6.2
4.8
3.8
99.3
96.3
84.5
77.1
71.2
66.7
63.1
61.0
59.9
58.9
58.3
57.7
57.3
54.8
50.7
48.3
47.8
45.5
39.8
31.7
25.3
20.7
16.9
13.9
11.3
9.0
7.0
5.9
115.9
112.3
98.5
89.8
83.0
77.9
73.7
71.0
69.8
68.6
68.0
67.4
67.0
64.0
59.1
56.2
55.8
53.1
46.4
37.1
29.4
24.1
19.7
16.4
13.3
10.6
8.2
6.9
PRESSURE (BAR)
PN 150 PN 190
132.4
128.4
112.8
102.9
95.2
89.1
84.5
81.3
79.8
78.6
77.6
77.0
76.4
72.9
67.5
64.5
63.9
60.8
53.1
42.1
33.8
27.3
22.3
18.6
15.2
12.1
9.3
7.6
182.1
176.5
154.7
141.2
130.9
122.6
116.1
111.6
109.7
107.9
106.6
106.0
105.1
100.2
92.7
88.6
87.9
83.6
73.1
58.2
46.5
37.8
30.9
25.8
21.0
16.7
12.9
10.3
PN 260
PN 310
248.3
240.6
211.0
192.4
178.5
167.1
158.1
152.3
149.3
147.2
145.6
144.4
143.4
136.7
126.4
120.7
119.8
114.0
99.5
79.2
63.3
51.5
42.0
35.0
28.7
22.9
17.4
14.1
297.9
288.8
253.2
231.0
214.2
200.3
189.6
182.8
179.3
176.8
175.0
173.1
172.0
164.0
151.6
144.8
143.8
136.9
119.4
94.9
75.9
62.0
50.3
41.9
34.4
27.5
21.0
16.9
PN 420
413.8
401.0
351.7
320.9
297.3
278.2
263.6
253.8
249.1
245.4
242.9
240.4
239.0
228.0
210.7
201.0
199.5
190.1
166.0
131.8
105.7
86.1
69.8
58.2
47.7
38.0
29.2
23.8
PN 490
PN 760
480.0
465.2
408.0
372.2
344.8
322.6
305.6
294.4
289.0
284.7
281.9
278.8
277.3
264.5
244.4
233.1
231.4
220.5
192.4
152.8
122.4
99.8
80.9
67.6
55.3
44.2
34.0
27.6
744.8
721.9
633.2
577.7
535.2
500.8
474.5
456.9
448.3
441.9
437.2
432.8
430.3
410.5
379.2
361.7
359.0
341.9
298.6
237.3
189.8
154.8
125.8
104.9
85.6
68.4
52.6
42.8
1. Shaded ratings may require special trim and packing, consult your Edward Valves representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H25
Edward Valves
ASTM A-315-CF8M
SPECIAL CLASS
(1)
TEMPERATURE
C
-29 to 38
50
100
150
200
250
300
350
375
400
425
450
475
500
525
538
550
575
600
625
650
675
700
725
750
775
800
816
PN 50
PN 68
51.7
50.8
47.0
43.0
39.6
37.0
35.3
34.0
33.4
32.7
32.4
32.1
32.1
31.8
30.2
29.0
29.0
28.0
24.8
19.7
15.7
12.9
10.4
8.7
7.2
5.8
4.4
3.4
69.0
67.8
62.7
57.1
52.8
49.6
47.0
45.0
44.4
43.8
43.5
42.9
42.5
42.2
40.2
38.6
38.6
37.4
33.3
26.4
21.2
17.2
14.0
11.7
9.5
7.7
6.0
4.8
PRESSURE (BAR)
PN 110
PN 120
PN 150
103.4
101.6
94.1
86.1
79.2
74.4
70.5
67.7
66.7
65.5
65.2
64.3
63.9
63.4
60.3
57.9
57.9
56.2
49.9
39.5
31.8
25.9
20.9
17.4
14.3
11.4
8.8
7.2
120.7
118.6
109.8
100.2
92.4
86.6
82.3
79.0
77.7
76.5
75.9
75.0
74.6
74.0
70.4
67.6
67.6
65.5
58.1
46.1
36.9
30.1
24.4
20.4
16.7
13.3
10.2
8.3
155.2
152.4
141.1
128.7
118.8
111.4
105.8
101.7
100.1
98.2
97.6
96.7
96.0
95.2
90.5
86.9
86.9
84.2
74.7
59.2
47.5
38.9
31.3
26.2
21.5
17.2
13.2
10.7
PN 190
PN 260
PN 310
PN 420
PN 490
PN 760
189.7
186.3
172.5
157.3
145.2
136.2
129.3
124.2
122.1
120.3
119.4
118.2
117.4
116.4
110.6
106.2
106.2
102.9
91.3
72.6
58.1
47.3
38.4
32.0
26.2
21.0
16.2
13.1
258.6
254.1
235.2
214.8
198.0
185.5
176.4
169.3
166.5
164.1
162.5
161.0
159.9
158.6
151.0
145.2
145.2
140.5
124.3
98.9
79.0
64.4
52.4
43.7
35.6
28.5
22.0
17.9
310.3
304.9
282.2
257.8
237.7
222.9
211.8
203.0
199.9
196.8
195.3
193.1
191.7
190.3
181.3
174.1
174.1
168.6
149.4
118.7
95.1
77.4
62.9
52.4
42.8
34.3
26.4
21.4
431.0
423.4
392.0
358.0
330.1
309.5
293.8
281.9
277.6
273.4
271.2
268.4
266.4
264.1
251.6
241.7
241.7
234.1
207.5
164.8
132.0
107.5
87.3
72.8
59.5
47.6
36.6
29.7
500.0
491.2
454.7
415.1
382.9
359.1
340.8
327.2
322.0
317.1
314.6
311.3
309.2
306.4
291.8
280.3
280.3
271.6
240.7
191.3
153.2
124.7
101.3
84.5
69.0
55.1
42.4
34.5
775.9
762.2
705.6
644.4
594.1
556.9
529.0
507.8
499.8
491.9
487.9
483.0
479.8
475.7
452.9
435.2
435.2
421.3
373.2
296.5
237.4
193.6
157.1
131.0
107.1
85.7
65.7
53.1
1. Shaded ratings may require special trim and packing, consult your Edward Valves representative for applications in these ranges.
* Pressure temperature ratings are from ASME B16.34 Valves, Flanged, Threaded and Welding Ends.
Consult your Edward Valves sales representative for pressure temperature ratings of materials not included in this catalog.
H26
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
End Configurations
American Steel Flange Standards ASME B16.5 Dimensions in Inches
Nominal
Pipe
Size
O
Outside
Diameter
of
Flange
R
Outside
Diameter
of Raised
Face
C*
Minimum
Thickness
of
Flange
A
Diameter
of
Bolt
Circle
Number
of
Bolt
Studs
Diameter
of
Bolt
Studs
0.56
0.62
0.69
0.75
0.81
0.88
1.00
1.12
1.25
1.38
1.44
1.62
1.88
2.00
2.12
2.62
3.25
3.50
3.88
4.50
5.00
5.88
6.62
7.88
9.25
10.62
13.00
15.25
17.75
20.25
4
4
4
4
4
8
8
8
8
8
12
12
16
16
20
1/2
5/8
5/8
5/8
3/4
5/8
3/4
3/4
3/4
3/4
3/4
7/8
1
1-1/8
1-1/8
0.62
0.75
0.75
0.75
0.88
0.75
0.88
0.88
0.88
0.88
0.88
1.00
1.12
1.25
1.25
0.56
0.62
0.69
0.81
0.88
1.00
1.12
1.25
1.50
1.75
1.88
2.19
2.50
2.62
2.75
2.62
3.25
3.50
3.88
4.50
5.00
5.88
6.62
8.50
10.50
11.50
13.75
17.00
19.25
20.75
4
4
4
4
4
8
8
8
8
8
12
12
16
20
20
1/2
5/8
5/8
5/8
3/4
5/8
3/4
3/4
7/8
1
1
1-1/8
1-1/4
1-1/4
1-3/8
0.62
0.75
0.75
0.75
0.88
0.75
0.88
0.88
1.00
1.12
1.12
1.25
1.38
1.38
1.50
1.62
1.50
1.75
2.00
2.19
2.50
2.75
3.12
3.38
7.50
7.50
9.25
11.00
12.50
15.50
18.50
21.00
22.00
8
8
8
8
12
12
16
20
20
1
7/8
1-1/8
1-1/4
1-1/8
1-3/8
1-3/8
1-3/8
1-1/2
1.12
1.00
1.25
1.38
1.25
1.50
1.50
1.50
1.62
0.88
1.00
1.12
1.12
1.25
1.50
1.62
1.88
2.12
2.88
3.25
3.62
4.25
4.88
5.25
3.25
3.50
4.00
4.38
4.88
6.50
7.50
8.00
9.50
11.50
12.50
15.50
19.00
22.50
25.00
4
4
4
4
4
8
8
8
8
8
12
12
12
16
16
3/4
3/4
7/8
7/8
1
7/8
1
1-1/8
1-1/4
1-1/2
1-3/8
1-5/8
1-7/8
2
2-1/4
0.88
0.88
1.00
1.00
1.12
1.00
1.12
1.25
1.38
1.62
1.50
1.75
2.00
2.12
2.38
1.19
1.25
1.38
1.50
1.75
2.00
2.25
2.62
3.00
3.62
4.25
5.00
6.50
7.25
3.50
3.75
4.25
5.12
5.75
6.75
7.75
9.00
10.75
12.75
14.50
17.25
21.25
24.38
4
4
4
4
4
8
8
8
8
8
8
12
12
12
3/4
3/4
7/8
1
1-1/8
1
1-1/8
1-1/4
1-1/2
1-3/4
2
2
2-1/2
2-3/4
0.88
0.88
1.00
1.12
1.25
1.12
1.25
1.38
1.62
1.88
2.12
2.12
2.62
2.88
Diameter
of
Bolt Stud
Holes
3.75
4.62
4.88
5.25
6.12
6.50
7.50
8.25
10.00
11.00
12.50
15.00
17.50
20.50
23.00
1.38
1.69
2.00
2.50
2.88
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
16.25
3.75
4.62
4.88
5.25
6.12
6.50
7.50
8.25
10.75
13.00
14.00
16.50
20.00
22.00
23.75
1.38
1.69
2.00
2.50
2.88
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
16.25
9.62
9.50
11.50
13.75
15.00
18.50
21.50
24.00
25.25
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
16.25
4.75
5.12
5.88
6.25
7.00
8.50
9.62
10.50
12.25
14.75
15.50
19.00
23.00
26.50
29.50
1.38
1.69
2.00
2.50
2.88
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
16.25
5.25
5.50
6.25
7.25
8.00
9.25
10.50
12.00
14.00
16.50
19.00
21.75
26.50
30.00
1.38
1.69
2.00
2.50
2.88
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
NPS
DN
NPS
DN
NPS
DN
NPS
DN
NPS
DN
NPS
1/4
0.555
0.38
8
14
10
3/8
0.690
0.38
10
18
10
1/2
0.855
0.38
15
22
10
3/4
1.065
0.50
20
27
13
1
1.330
0.50
25
34
13
1-1/4
1.675
0.50
1-1/2
1.915
0.50
40
49
13
2
2.406
0.62
50
61
16
2-1/2
2.906
0.62
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
DN
65
74
16
H27
Edward Valves
Threaded Ends
H28
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
End Preparations
Buttwelding Ends
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H29
Edward Valves
Buttwelding Ends
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
2-1/2
65
3
80
4
100
H30
PIPE1
SCH.
NO.
40
80
160
XXS
40
80
160
XXS
40
80
160
XXS
40
80
160
XXS
40
80
160
XXS
40
80
160
XXS
40
80
160
XXS
40
80
160
XXS
40
80
120
160
XXS
A
OUTSIDE
DIAMETER
B
INSIDE
DIAMETER
C
BORE OF
WELDING LIP
t
WALL
THICKNESS
INCHES
MM
INCHES
MM
INCHES
MM
INCHES
MM
0.840
21
1.050
27
1.315
33
1.660
42
1.900
48
2.375
60
2.875
73
3.500
89
4.500
114
0.622
0.546
0.464
0.252
0.824
0.742
0.612
0.434
1.049
0.957
0.815
0.599
1.380
1.278
1.160
0.896
1.610
1.500
1.338
1.100
2.067
1.939
1.687
1.503
2.469
2.323
2.125
1.771
3.068
2.900
2.624
2.300
4.026
3.826
3.624
3.438
3.152
15.8
13.9
11.8
6.4
20.9
18.8
15.6
11.0
26.6
24.3
20.7
15.2
35.1
32.5
29.5
22.8
40.9
38.1
34.0
27.9
52.5
49.3
42.9
38.2
63
59
54
45
78
74
67
58
102
97
92
87
80
0.608
0.542
0.470
0.285
0.811
0.740
0.626
0.470
1.041
0.961
0.837
0.648
1.374
1.285
1.181
0.951
1.605
1.509
1.367
1.159
2.065
1.953
1.734
1.571
2.479
2.351
2.178
1.868
3.081
2.934
2.692
2.409
4.044
3.869
3.692
3.530
3.279
15.4
13.8
11.9
7.2
20.6
18.8
15.9
11.9
26.4
24.4
21.3
16.5
34.9
32.6
30.0
24.2
40.8
38.3
34.7
29.4
52.5
49.6
44.0
39.9
62.95
59.7
55.3
47.45
78.25
74.5
68.4
61.2
102.7
98.25
93.8
89.65
83.3
0.109
0.147
0.188
0.294
0.113
0.154
0.219
0.308
0.133
0.179
0.250
0.358
0.140
0.191
0.250
0.382
0.145
0.200
0.281
0.400
0.154
0.218
0.344
0.436
0.203
0.276
0.375
0.552
0.216
0.300
0.438
0.600
0.237
0.337
0.438
0.531
0.674
2.8
3.7
4.8
7.5
2.9
3.9
5.6
7.8
3.4
4.5
6.4
9.1
3.6
4.9
6.4
9.7
3.7
5.1
7.1
10.2
3.9
5.5
8.7
11.1
5.15
7
9.55
14
5.5
7.6
11.15
15.25
6
8.55
11.15
13.5
17.1
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Buttwelding Ends
VALVE2
PRESSURE CLASS
NOMINAL
PIPE
SIZE
2-1/2
65
3
80
4
100
5
125
6
150
8
200
10
250
12
300
PIPE1
SCH.
NO.
40
80
160
XXS
40
80
160
XXS
40
80
120
160
XXS
40
80
120
160
XXS
40
80
120
160
XXS
40
60
80
100
120
140
XXS
160
40
60
80
100
120
140
160
STD
40
XS
60
80
100
120
140
160
3
0
0
6
0
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
9
0
0
1
5
0
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
A
OUTSIDE
DIAMETER
B
INSIDE
DIAMETER
t
WALL
THICKNESS
INCHES
MM
INCHES
MM
INCHES
MM
INCHES
MM
2.875
73
3.500
89
4.500
114
5.563
141
6.625
168
8.625
219
10.750
273
12.750
324
2.469
2.323
2.125
1.771
3.068
2.900
2.624
2.300
4.026
3.826
3.624
3.438
3.152
5.047
4.813
4.563
4.313
4.063
6.065
5.761
5.501
5.187
4.897
7.981
7.813
7.625
7.437
7.187
7.001
6.875
6.813
10.02
9.750
9.562
9.312
9.062
8.750
8.500
12.000
11.938
11.750
11.625
11.374
11.062
10.750
10.500
10.126
63
59
54
45
78
74
67
58
102
97
92
87
80
128
122
116
110
103
154
146
140
132
124
203
198
194
189
183
178
175
173
255
248
243
237
230
222
216
305
303
298
298
289
281
273
267
257
2.479
2.351
2.178
1.868
3.081
2.934
2.692
2.409
4.044
3.869
3.692
3.530
3.279
5.070
4.866
4.647
4.428
4.209
6.094
5.828
5.600
5.326
5.072
8.020
7.873
7.709
7.544
7.326
7.163
7.053
6.998
10.070
9.834
9.670
9.451
9.232
8.959
8.740
12.053
11.999
11.834
11.725
11.505
11.232
10.959
10.740
10.413
62.95
59.7
55.3
47.45
78.25
74.5
68.4
61.2
102.7
98.25
93.8
89.65
83.3
128.8
123.6
118.05
112.45
106.9
154.8
148.05
142.25
135.3
128.85
203.7
199.95
195.8
191.6
186.1
181.95
179.15
177.75
255.8
249.8
245.6
240.05
234.5
227.55
222
306.15
304.75
300.6
297.8
292.25
285.3
278.35
272.8
264.5
0.203
0.276
0.375
0.552
0.216
0.300
0.438
0.600
0.237
0.337
0.438
0.531
0.674
0.258
0.375
0.500
10.625
0.750
0.280
0.432
0.562
0.719
0.864
0.322
0.406
0.500
0.594
0.719
0.812
0.875
0.906
0.365
0.500
0.594
0.719
0.844
1.000
1.125
0.375
0.406
0.500
0.562
0.688
0.844
1.000
1.125
1.312
5.15
7
9.55
14
5.5
7.6
11.15
15.25
6
8.55
11.15
13.5
17.1
6.55
9.55
12.7
15.9
19.05
7.1
10.95
14.25
18.25
21.95
8.2
10.3
12.7
15.1
18.25
20.6
22.25
23
9.25
12.7
15.1
18.25
21.45
25.4
28.6
9.55
10.3
12.7
14.25
17.5
21.45
25.4
28.6
33.3
X
X
X
X
X
X
X
X
X
X
X
X
C
BORE OF
WELDING LIP
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
H31
Edward Valves
Buttwelding Ends
VALVE2
PRESSURE CLASS
NOMINAL
PIPE
SIZE
14
350
16
400
18
450
20
500
22
550
24
600
PIPE1
SCH.
NO.
STD
40
XS
60
80
100
120
140
160
STD
40
60
80
100
120
140
160
40
60
80
100
120
140
160
40
60
80
100
120
140
160
STD
XS
60
80
100
120
140
160
STD
XS
30
40
60
80
100
120
140
160
3
0
0
6
0
0
9
0
0
1
5
0
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
A
OUTSIDE
DIAMETER
B
INSIDE
DIAMETER
t
WALL
THICKNESS
INCHES
MM
INCHES
MM
INCHES
MM
INCHES
MM
14.000
356
16.000
406
18.000
457
20.000
508
22.000
559
24.000
610
13.25
13.124
13
12.812
12.5
12.124
11.812
11.5
11.188
15.25
15
14.688
14.312
13.938
13.562
13.124
12.812
16.876
16.500
16.124
15.688
15.250
14.876
14.438
18.812
18.376
17.938
17.438
17
16.5
16.062
21.25
21
20.25
19.75
19.25
18.75
18.25
17.75
23.25
23
22.876
22.624
22.062
21.562
20.938
20.376
19.876
19.312
337
333
330
325
318
308
300
292
284
387
381
373
364
354
344
333
325
429
419
410
398
387
378
367
478
467
456
443
432
419
408
540
533
514
502
489
476
464
451
591
584
581
575
560
548
532
518
505
491
13.303
13.192
13.084
12.92
12.646
12.318
12.044
11.771
11.498
15.303
15.084
14.811
14.482
14.155
13.826
13.442
13.17
16.975
16.646
16.318
15.936
15.553
15.225
14.842
18.92
18.538
18.155
17.717
17.334
16.896
16.513
21.303
21.084
20.428
19.99
19.553
19.115
18.678
18.24
23.303
23.084
22.975
22.755
22.263
21.826
21.28
20.788
20.35
19.857
337.9
335.1
332.35
328.15
321.2
312.9
305.9
299
292.05
388.7
383.15
376.2
367.85
359.55
351.2
341.45
334.5
431.15
422.8
414.5
404.75
395.05
386.7
377
480.55
470.85
461.15
450
440.3
429.15
419.45
541.1
535.55
518.85
507.75
496.65
485.5
474.4
463.3
591.9
586.35
583.55
578
565.5
554.4
540.5
528
516.9
504.35
0.375
0.438
0.5
0.594
0.75
0.938
1.094
1.25
1.406
0.375
0.5
0.656
0.844
1.031
1.219
1.438
1.594
0.562
0.75
0.938
1.156
1.375
1.562
1.781
0.594
0.812
1.031
1.281
1.5
1.75
1.969
0.375
0.5
0.875
1.125
1.375
1.625
1.875
2.125
0.375
0.5
0.562
0.688
0.969
1.219
1.531
1.812
2.062
2.344
9.55
11.15
12.7
15.1
19.05
23.85
27.8
31.75
35.7
9.55
12.7
16.65
21.45
26.2
30.95
36.55
40.5
14.25
19.05
23.85
29.35
34.95
39.65
45.25
15.1
20.6
26.2
32.55
38.1
44.45
50
9.55
12.7
22.25
28.6
34.95
41.3
47.65
54
9.55
12.7
14.25
17.5
24.6
30.95
38.9
46
52.35
59.55
X
X
X
X
X
X
X
X
X
X
X
X
C
BORE OF
WELDING LIP
H32
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
EV100
5th Edition
Maintenance
Edward Valves
Maintenance
EDWARD VALVES
ON-SITE FIELD SERVICE REPAIR CAPABILITIES
J2
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
Edward Valves
Maintenance
STAYING ON-LINE
WITH EDWARD VALVES
We design and manufacture all our valves
for 40 years life in the field. That means
not just building a reliable product, but
one that is easy to maintain and service. It
also means providing a team of
experienced, dedicated professionals to
keep your Edward valves operating at
peak performance.
Highly Experienced Technicians
Edward brings unmatched experience to the
field. Our service technicians have an
average 20 years in the industry, and 15
years with Edward. Each has special skills,
such as welding and machining, that we can
target for the needs of the individual job.
Comprehensive Record-Keeping
Our files include original specifications for
every Edward valve sold since 1908. All
valves are coded for easy identification.
On new and replacement orders, Edward
stands ready to provide the complete lottraceability required for nuclear and other
critical services.
In-Line Service
We are dedicated to on-site service
whenever possible. To this end, we not
only provide highly experienced, expert
personnel we also support those
technicians with field equipment,
including portable boring, lapping,
welding, and weld-cutting machines.
Major parts, such as disks or bonnets, can
be air-shipped back to the factory for
service, and repaired while service
personnel perform other tasks.
Parts Replacement
Our comprehensive record-keeping
system also facilitates replacement of
parts. Our computer database can quickly
tell us if we have the part in stock or on
order, or how we can best coordinate raw
materials and factory resources for the
quickest possible turn-around time.
H
J
EDWARD VALVES.
THERE IS NO EQUAL.
Edward Valves 1900 South Saunders Street, Raleigh, North Carolina 27603 1-800-225-6989 1-919-832-0525 Fax 1-919-831-3369
J3
Edward Valves
Edward Valves
Edward Valves
1900 South Saunders Street
Raleigh, North Carolina 27603 USA
US Sales Offices
Phone:
919- 832- 0525
Facsimile: 919- 831- 3369
Facsimile: 919- 831- 3376
Visit Our Website
www. edwardvalves. com
While the information and specifications contained in this literature are believed to be accurate, they are supplied for informative purposes only and should not be
considered certified or as a guarantee of satisfactory results by reliance thereon. Nothing contained herein is to be construed as a warranty or guarantee, express
or implied, regarding any matter with respect to this product. Because Flowserve is continually improving and upgrading its product design, the specifications,
dimensions and information contained herein are subject to change without notice. Should any question arise concerning these provisions, the purchaser/user
should contact Flowserve Corporation at any one of its worldwide operations or offices.
Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this Flowserve product is
designed to perform its intended function safely during its useful life. However, the purchaser or user of Flowserve products should be aware that Flowserve
products might be used in numerous applications under a wide variety of industrial service conditions. Although Flowserve can (and often does) provide general
guidelines, it cannot provide specific data and warnings for all possible applications. The purchaser/user must therefore assume the ultimate responsibility for the
proper sizing and selection, installation, operation, and maintenance of Flowserve products. The purchaser/user should read and understand the Installation
Operation Maintenance (IOM) instructions included with the product, and train its employees and contractors in the safe use of Flowserve products in connection
with the specific application.
Edward Valves
EV100
5th Edition
FLOWSERVE CORPORATION
FLOW CONTROL DIVISION
Edward Valves Operations
1900 South Saunders Street
Raleigh, North Carolina 27603
USA
Phone:
919- 832- 0525
Facsimile: 919- 831- 3369
Facsimile: 919- 831- 3376
www. edwardvalves. com
Edward Valves
2002 Flowserve Corporation, Irving, Texas, USA. Flowserve and Edward Valves are registered trademarks of Flowserve Corporation.