Beruflich Dokumente
Kultur Dokumente
This manual contains important safety precautions and information for correct usage. Please be
sure to read this manual carefully before use to avoid any damage to the device.
Do not place the product in hot, wet or dusty environments.
Do not place the product for outdoor usage.
Avoid dropping or smashing the product.
Select a suitable product with correspondent maximum load of current upto 15A.
Notes:
This device is not waterproof.
All images in this manual are for reference only. Specifications and appearance of the product
are subject to change without prior notice.
1. Location of Controls
1. IR LED
2. System LED (Blue)
3. MIC
4. PIR (Passive infrared sensor)
5. POWER LED (Red)
6. MICRO USB (For Power Supply)
7. MICRO SD Card Slot
8. Reset (After 15 seconds to return to default setting including password)
9. Antenna
2.GETTING STARTED
Congratulations on buying a iCraig Camera. This device will enable you to easily
check your loved ones by viewing them while you are away.
1.Initial Setup
To get started, you will need:
Your wireless router, its network name, and password if necessary.
Make sure your Smart phone or tablet, the wifi status is ON.
3.Download the iCraig SMART App from the App Store or Google Play.
After installing your app, open the APP, press and to choose Add new online
Cameraicon to activate the APP.
4.Check your iCraig cam LED lights which indicate the status as below:
Blue LED Light Slow
Blue LED light Fast
Blue LED light
When the iCraig Cam Blue LED light is flashing slowly, Go to Settings -----> Choose
Wi-Fi on your Smart Phone or tablet to look for the wifi name similar to
PQXXXXX_XXXXXXXXXXXX_XXXXXX
Tap on camera you want to connect and press OK to connect. Wait until the new
camera Logging in successfully, you will see the camera online status appear on
your screen. Now app connected with IP camera through AP (Access Point) mode.
10
Tap the WIFI Config and choose your wifi network by identifying your network
name.
Input your wifi network password if needed.
11
Tap OK, it will display confirmation message if all required wifi name/password is correct.
Then touch OK, the camera will start to reboot. Once complete, it shows Device
reboot
The new camera will logging in to your home network automatically, wait until the
camera appears online, X User (blue word) successfully. Now it is finish setup.
12
13
Locate your QR Code label on the back of wifi camera which is similar to this
use your Smart Phone to aim on the QR code after pressing the QR SCAN icon on
the APP screen.
Choose your wifi network by identifying your network name
Input your wifi network password if needed.
14
Wait until the Add New Device icon display on app screen, and then touch it. You
can see new connected device shows on Search Device page (see below)
Tap the new device then Press OK, the new camera will logging in, wait until the
camera appear online, X User (blue word) successfully. Now it is finish setup.
15
7.Other Functions
Touch the camera screen on your smartphone, it will appear control panel as below:
16
High
Normal
Low
Bandwidth
The quality of the low bandwidth when the current frame image
Adjust the brightness
Adjust the contrast
Open and Close MIC
No function
Smartphone Screenshot
Smartphone Record
NO FUNCTION
NO FUNCTION
The current frame mirror left and right
The current picture mirror up and down
8.Settings:
Tap the Setting icon
on your Live Cam page, see below pictures
Choose Modify Camera to rename the camera.
Choose Delete the camera stored in this app.
Choose reconnect to reconnect your camera online again.
17
Alarm Config
Select motion detection sensitivity by pressing on the icon and sensitivity screen will
pop up for you to choose.
Choose disable if you do not wish to have this alert.
- To set up motion detection by enabling PIR sensor by sliding the icon to the right
hand side.
18
you have forgotten the password, press the RESET button on the back of
the device for about 15s.
19
Time Setting:
To sync with the smart phone and the app on real time by pressing Device Time
Sync
with App.
20
Camera reboot:
Enable remotely restart the camera. If camera works abnormally, you can do this
step to reboot/restart camera.
21
10.Troubleshooting
Cannot power on the Device
Check your power source.
T
Cannot go online
Check if your WI-FI setting is correct, proper password may be needed.
Check if your router is working properly.
Check your signal, your device may not be to connect due to weak WI-FI signal.
22
11. Specification
PRODUCT SPECIFICATIONS
Hardware Features and Specifications
Still Image Capture
Video Features
Audio In
Audio Compression
Built-in microphone,
ADPCM
Camera
Image Sensor
Lens
View Angle
IR LEDs
10 IR LEDs,
IR Mode
Networking
Network Interface
Wireless
Connectivity
Radio
Specifications
Antenna
Video
MJPEG
Codecs
Resolution
320X240
Frame Rate
Up to 30 frames
Accessories:
Power
IB
Cable
23
24