Beruflich Dokumente
Kultur Dokumente
NO.
CODE
DESCRIPTION
SET
QTY
DIRECT COST
1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
Architecture
Single profiled plate roof(incl.daylighting band, no
purline), requirement as follows:1.0mm plastic steel
anti-corrosion plate adopted for roof(Grade A for
non-combustible fire-proof plate).
Inverted roof, the structure as follows:1)coating
aggregate protective layer; 2)20mm 1:3 cement
mortar;3)30mm extruded polystyrene foam sheet;
4)1.2mm synthetic polymeric water proof sheet +
1.5mm spraying quick-setting rubber asphalt
waterproof coating; 5) 20mm 1:3 cement mortar;
6)30mm LC 5.0 light aggregate concrete,2% sloping;
7)reinforced concrete roof board.
Cement mortar floor, the structure as
follows:1)20mm 1.:2.5 cement mortar, adding
appropriate cement powder on the surface to level
off; 2)brushing a layer of cement paste(mixed with
construction glue); 3)caste-in-place reinforced
concrete floor.
Fine stone concrete ground, the structure as follows:
1)40 mm C25 fine stone cement, spreading cement
sand(mix ratio: 1:1), along with finishing, coating
with seal solidification agent on the surface;
2)brushing a layer of cement paste(mixed with
construction glue); 3)100 mm C15 concrete cushion;
4) tamping with 150 mm gravel.
Great white pulp ceiling, the structure as follows:
1)cleaning base; 2) local puttying,smoothing with
sandpaper; 3)white washing 2 times(mixing ratio by
weight:whiting powder 100: construction glue
Puttying
15~20. inner wall, the structure as follows: 1)
screeding with 9mm 2:1:6 cement lime mortar for
several times; 2) screeding with 2 mm surface layer
of waterproof putty for several times; 3)white
washing 2 times(mixing ratio by weight: whiting
powder 100: construction glue 15~20.
Cement mortar skirtingh=150), the structure as
follows: 1) finishing with 8 mm 1:2.5 cement
mortar;2)under-coating and drawing lines with
12mm 1:3 cement mortar; 3)brick wall.
Cement mortar aproll, the structure as follows:
1)screeding with 20 mm 1:2 cement mortar; 2)
60mm C15 concrete; 3)tamping bedding with
100mm rubble clay(stone, pebble clay); 4)rammed
earth, outward slope 4%.
7,400.00
85.00
2,200.00
1,200.00
1,000.00
4,550.00
180.00
522.00
page 1 from 16
NO.
1.9
1.10
1.11
1.12
1.13
CODE
DESCRIPTION
Cement mortar step, the structure as follows:
1)screeding with 20 mm 1:2 cement mortar; 2)
60mm C15 concrete; 3)100mm C15 concrete
4)rammed earth.
Single profiled wall surface (incl.daylighting band, no
purline),requirement as follows:0.7mm plastic steel
anti-corrosion plate adopted for wall surface(Grade A
for non-combustible fire-proof plate).
Exterior wall coating, the structure as follows:
1)12mm 1:3 cement mortar; 2)screeding with 8mm
1:2.5 cement mortar; 3)spraying or rolling brush
primer for 1 time; 4)spraying or rolling brush
painting for 2 times;
Common burnt brick(incl.holes with area less than
0.3m2)
Grade B for wooden fireproof door: fire insulation
1.00h,fire endurance 1.00h;
SET
QTY
6.30
4,200.00
800.00
265.00
43.20
1.14
1,050.00
1.15
16.00
1.16
2
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Structure
K150 plain concrete
K300 concrete (used for foundation)
K300 concrete (used for superstructure)
K350 concrete (used for superstructure)
Steel member Q235B
Steel bar (incl. HPB300, HRB400)
Crane rail QU100 (incl.rail fittings)
Embedded parts (Q235B)
m3
m3
m3
m3
t
t
t
t
802.03
1,293.60
5,767.05
1,074.54
914.27
598.76
35.76
5.00
Carbon
3.1
unit
3.2
unit
page 2 from 16
NO.
CODE
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
SET
QTY
unit
unit
unit
unit
unit
unit
unit
unit
unit
t
t
t
t
8
1
1
5
3.12
3.13
3.14
3.15
4
4.1
DESCRIPTION
03001
Attach
Attach
Attach
4.2
03002
4.3
Attach
Attach
Attach
03003
Ventilation
Pulse bag filter:Blowing rate:23100m2/hActive filter
Set
area:395.5m2, Filter material:Ultra-Web nanofiber
media, Pressure drop: 1200Pa
Screw conveyor: volts:380V, power:2.2kW
Set
Rotary air lock valve: 220x220 volts:380V,
Set
power:1.5kW
Set
Pulse Control System, power:0.25kW
Pulse bag filter: Blowing rate: 8400m2/h, Active filter
area:135.6m2, Filter materialUltra-Web nanofiber
Set
media, Pressure drop: 1200Pa
Screw conveyor: volts:380V, power:2.2kW
Set
Rotary air lock valve: 220x220 volts:380V,
Set
power:1.5kW
Set
Pulse Control System, power:0.25kW
Centrifugal fan: Flow rate: 27758 m3/h, Pressure:
Set
4106Pa
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
page 3 from 16
NO.
CODE
Attach
4.4
03004
Attach
4.5
4.6
4.7
4.8
4.9
5.1
5.2
5.3
DESCRIPTION
Power:45 kW, Volts: 380V, Rotation speed: 960
r/min,Protection level:IP55
Centrifugal fan:Flow rate: 11270 m3/h, Pressure:
3048Pa
Power:15 kW, Volts: 380V, Rotation speed: 2900
r/min,Protection level:IP55
Duct thickness: 2mm, Material: Q235-A
Manual butterfly valve 420, Material: Q235-A
Manual butterfly valve 280, Material: Q235-A
Manual butterfly valve 200, Material: Q235-A
Manual butterfly valve 140, Material: Q235-A
SET
Set
2.00
Set
2.00
Set
2.00
Ton
Set
Set
Set
Set
12.00
2.00
6.00
4.00
10.00
Electrical
LV switch Cabinet, rated insulating
voltage:1000VUi=690V,rated operational
voltage:440V, rated impulse withsand
voltage:8kV;over vlotage class: III, rated frequency:
50Hz, No. of phases(Busbar): 3P+N+PE,Rated
current of horizontal main busbar:2500A, Rated peak
withstand current (Ipk) : 100kA,Rated short-time
withstand current (Icw) : 40kA/s ,Rated current of
vertical busbar : 1500A ,Rated peak withstand
unit
current of distribution busbar (Ipk): 100kA,Rated
short-time withstand current of distribution busbar
(Icw): 40kA/s, Protection class: IP54,Color:
N6.5,Height*width*depth: 2200mm* 1000mm
*1000mm,
loop of the electrical motor equiped with curretn
transformer,intermeidate relay and Phoenix
terminals, drawers equiped with ammeter, signal
lights; feeder loop curretn transformer and ammeter
Local Control Box,Rated insulation voltage:
660VAC,Rated operational voltage:
220VAC,Overvoltage class: III ,Pollution class: III
,Rated frequency: 50Hz, Protection class:
IP54,Material: PC Material ,Color: N6.5
,Height*width*depth: 300mm* 200mm *150mm ,
unit
20 hole at bottom, with Conduit Adaptor, Changeover switch: 3 gears
(manual/automatic/maintenance),Control button
(stop):
1NO+1NC,
Green,Control
(start):
Local Control
Box,Rated
insulationbutton
voltage:
1NO+1NC,
Red,
with
Phoenix
Terminals.
660VAC,Rated operational voltage:
220VAC,Overvoltage class: III ,Pollution class: III
,Rated frequency: 50Hz, Protection class:
IP54,Material: PC Material ,Color: N6.5
,Height*width*depth: 300mm* 200mm *150mm ,
20 hole at bottom, with Cable gland, Change-over
switch: 3 gears
(manual/automatic/maintenance),Control button
(stop): 1NO+1NC, Green,Control button (start):
1NO+1NC, Red, with Phoenix Terminals
QTY
unit
20
page 4 from 16
NO.
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
5.16
CODE
DESCRIPTION
SET
Lighting Distribution Box, Rated insulation voltage:
660VAC,Rated operational voltage:
220VAC,Overvoltage class: III ,Pollution class: III
,Rated frequency: 50Hz, Current tolerance (KA):
15KA, Protection class: IP54, Material: PC Material,
Color: N6.5, Height*width*depth: 350mm* 480mm
*150mm,8 switches 20A/2P, 1 switch 20A/2P vigi
unit
30mA, Lighting transformer(aside Lighting
Distribution Box ):30kVA, 415V/380V5%, Y, yn0.
Recommended
manufacturers of:
-Circuit breakers: ABB, Siemens, TerasakiCT, or
equivalent Power Supply Box ,Rated insulation
-Lighting
Maintenance
transformer:
Local
(Indonesia)
product
voltage:
690VAC
,Rated
operational
voltage:
415VAC220VAC, Overvoltage class: III, Rated
frequency: 50Hz, Current tolerance (KA): 30KA
,Protection class: IP54, Material: PC Material, Color:
N6.5, Height*width*depth: 700mm* 500mm
*250mm, 3 50 holes at bottom, with Cable gland,
unit
Swithes:100A3P*132A3P*116A1P*1
10A2P*1vigi 30mA),Three-phase socket:
3P+N +PE: 32A, 4-pole, 32A/450VAC , Single-phase
socket: 1P+N +PE: 10A, 3-pole, 10A/250VAC, Singlephase socket: 2-pole, 10A/250VAC, transformer:
400VA , 250VAC/36VAC.
crown block sliding contact, phase:3P+N, Rated
insulation voltage: 690VAC, Rated operational
voltage: 415VAC, Overvoltage class: III,Pollution
class: III, Rated frequency: 50Hz, Current: 300A
crown block power box, Rated insulation voltage:
690VAC, Rated operational voltage: 415VAC,
Overvoltage class: III,Pollution class: III, Rated
frequency: 50Hz, Current tolerance (KA): 30KA,
Protection class: IP54, Material: PC Material, Color:
N6.5, Height*width*depth: 300mm* 250mm
*200mm, Switch:63A3P*1
Cable Tray400*150
Cu core,Power Cable:Insulation:XLPE,
Uo/U=0.66/1.1kV; PVC sheath Armoured, Flame
retardant,
Cu. 3*50+1*25
Cu core,Power
CableInsulation:XLPE,
Uo/U=0.66/1.1kV; PVC sheath Armoured, Flame
retardant, Cu. 3*35+1*16
Cu core,Power CableInsulation:XLPE,
Uo/U=0.66/1.1kV; PVC sheath Armoured, Flame
retardant, Cu. 3*25+1*16
Cu core,Power Cable:Insulation:XLPE,
Uo/U=0.66/1.1kV; PVC sheath Armoured, Flame
retardant, Cu. 4*25+1*16
Cu core,Power CableInsulation:XLPE,
Uo/U=0.66/1.1kV; PVC sheath Armoured, Flame
retardant, Cu. 5*16
Cu core,Power Cable:Insulation:XLPE,
Uo/U=0.66/1.1kV; PVC sheath Armoured, Flame
retardant, Cu. 4*16
Cu core,Power Cable:Insulation:XLPE,
Uo/U=0.66/1.1kV; PVC sheath Armoured, Flame
retardant, Cu. 4*10
Cu core,Power Cable:Insulation:XLPE,
Uo/U=0.66/1.1kV; PVC sheath Armoured, Flame
retardant, Cu. 4*6
QTY
fourphase
metre
250
unit
300
300
400
400
350
200
200
400
400
page 5 from 16
NO.
5.17
5.18
CODE
DESCRIPTION
Cu core,Power Cable:Insulation:XLPE,
Uo/U=0.66/1.1kV; PVC sheath Armoured, Flame
retardant, Cu. 4*4
Cu core,Control Cable :Insulation:XLPE,
Uo/U=450/750V; PVC sheath Screen; Cu. 10*1.5
SET
QTY
500
400
5.19
450
5.20
500
5.21
500
set
20
m
m
m
m
m
m
m
set
m
m
m
set
m
m
100
250
72
96
120
240
1500
15
900
500
300
150
2500
3500
ls
ls
15
ls
5.22
5.23
5.24
5.25
5.26
5.27
5.28
5.29
5.30
5.31
5.32
5.33
5.34
5.35
5.36
Instrumentation
8.1
8.2
8.3
Telecommunication
Fire alarm control unit; power supply, the main
power is 220V AC, range of voltage variety is
+10%~-15%; consume power:100W;bus
length:2000m(with a network card)
Point-type photoelectric smoke fire detector
ambient temperature-10C~55Cambient
humidity:95%RH(no condensation); operating
voltage:24V;monitoring current:0.35mA;alarming
current0.8mA;thready format:two bus(no polarity).
Backup Power:DC12V 2.2Ah
page 6 from 16
NO.
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
CODE
DESCRIPTION
SET
QTY
ls
ls
ls
ls
ls
ls
ls
10
ls
10
ls
ls
ls
ls
ls
ls
page 7 from 16
NO.
CODE
DESCRIPTION
SET
QTY
8.18
ls
8.19
ls
14
8.20
1000
16
unit
unit
0.56
5.67
unit
watermeter (DN40)
unit
1.00
unit
piece
14
piece
2
6
8
5
10
page 8 from 16
UNIT RATE
TOTAL
DIRECT COST
page 9 from 16
UNIT RATE
TOTAL
page 10 from 16
UNIT RATE
TOTAL
page 11 from 16
UNIT RATE
TOTAL
page 12 from 16
UNIT RATE
TOTAL
page 13 from 16
UNIT RATE
TOTAL
page 14 from 16
UNIT RATE
TOTAL
page 15 from 16
UNIT RATE
TOTAL
page 16 from 16