Beruflich Dokumente
Kultur Dokumente
Number: 4002472206
Item no.: 800
Date: 16/02/2016
Page: 1 / 7
Version no.: 19
Operating data
Requested flow rate
32.80 m/h
Operating data determined for maximum inlet pressure
Requested developed head
587.58 m
Pumped medium
Water, boiler feed water
Mode of operation AF
Not containing chemical and
mechanical substances which
affect the materials
Solids content max. 50 ppm
Ambient air temperature
20.0 C
Fluid temperature
Fluid density
Fluid viscosity
Suction pressure max.
Suction pressure min.
NPSH available
Vapour pressure
Mass flow rate
Max. power on curve
Minimum flow for stable curve
Minimum allowable flow for
continous operation
104.8 C
954 kg/m
0.29 mm/s
1.20 bar.g
1.20 bar.g
10.76 m
1.19 bar.a
8.70 kg/s
93.23 kW
23.86 m/h
8.38 m/h
32.80 m/h
587.64 m
68.3 %
73.24 kW
2979 rpm
2.14 m
63.00 bar.g
Shutoff pressure
Min. allow. flow for short term
operation
Min. mass flow for stable
curve
Min. allow. mass flow for
continuous operation
Min. allow. mass flow short
term operation
Shutoff head
Max. allow. flow rate
Max. allow. mass flow
Design
Performance test
61.91 bar.g
8.38 m/h
56.21 bar.g
6.33 kg/s
2.22 kg/s
2.22 kg/s
648.60 m
50.31 m/h
13.34 kg/s
Single system 1 x 100 %
Yes
Data sheet
Number: 4002472206
Item no.: 800
Date: 16/02/2016
Page: 2 / 7
Version no.: 19
Design
Variant
Stage number
Balance drum
Design
Orientation
Suction nominal dia.
Suction nominal pressure
Suction position
Suction flange drilled
according to standard
Discharge nominal dia.
Discharge norminal pressure
Discharge position
Discharge flange drilled
according to standard
Shaft seal
Manufacturer
Type
Material code
D
15
with piston
Baseplate mounted, longcoupled
Horizontal
DN 80
PN 25
top (0/360)
EN 1092-1
DN 50
PN 63
top (0/360)
Viewed from the drive
EN 1092-1
Single acting mechanical seal
Burgmann
H7N
Q1AEGG
81
E Single acting mechanical
(external circulation)
Minimum requirements for hot water quality: treatment acc. to
VdTV regulation TCH 1466
With SiO2-content up to max. 10 mg/l. Conductivity max. 50
S/cm for water with low salt content up to 160C or
conductivity max. 250 S/cm up to 140C for water with higher
salt content
Solids content up to max. 5 mg/l and no additives forming a
greasy film on the seal faces.
Seal chamber design
Standard seal chamber
Wear ring
Casing wear ring
Impeller diameter
173.0 mm
Minimum impeller diameter
155.0 mm
Full impeller diameter
173.0 mm
Free passage size
10.0 mm
Direction of rotation from drive Anticlockwise
Bearing bracket construction Standard (normal) two-sided
Bearing bracket size
50
Bearing seal
Thrower
Bearing type
Anti-friction bearings
Lubrication type
Grease
Temperature sensor PT100
Without
mts
Color
Ultramarine blue (RAL 5002)
KSB-blue
Driver, accessories
Manufacturer
Coupling type
Nominal size
Spacer length
Flender
Eupex NH
160
140.0 mm
Baseplate type
Baseplate size
Driver type
Drive standard mech.
Model (make)
Drive supplied by
Electric motor
IEC
KSB-Motor
Standard motor supplied by
KSB - mounted by KSB
B3
280M
Efficiency class IE3 acc. to
IEC60034-30-1
2979 rpm
Frequency
Rated voltage
Rated power P2
Available reserve
Rated current
Starting current ratio
Insulation class
Motor enclosure
Cos phi at 4/4 load
Motor efficiency at 4/4 load
Temperature sensor
Terminal box position
Motor winding
Number of poles
Connection mode
Motor cooling method
Motor material
Motor noise pressure level
50 Hz
400 V
90.00 kW
22.88 %
159.6 A
8
F to IEC 34-1
IP55
0.86
95.0 %
3 PTC resistors
0/360 (top)
Viewed from the drive
400 / 690 V
2
Delta
Surface cooling
Grey cast iron GG/CAST
IRON
81 dBa
Data sheet
Number: 4002472206
Item no.: 800
Date: 16/02/2016
Page: 3 / 7
Version no.: 19
Materials 20
Notes
Quality AF: pH > 9 (target >= 9.3) at 25C and O2 content <=
0.02 mg/kg for unalloyed cast iron components.
Quality AF: pH > 9 (target >= 9.3) at 25C for unalloyed steel or
cast steel components.
Suction casing (106)
Carbon steel GP240GH+N
Discharge casing (107)
Carbon steel GP240GH+N
Stage casing (108)
Steel 1.0576 S355J2H
Diffuser (171)
Grey cast iron EN-GJL-250
Shaft (210)
Chrome steel
1.4021QT700+SR
Impeller (230)
Grey cast iron EN-GJL-250
Impeller, suction stage (231) Grey cast iron EN-GJL-250
Certifications
Hydraulic performance test
Acceptance standard
Quantity meas. points Q-H
Certificate
Test participation
Quantity, non-witnessed
Quantity, witnessed
Suction casing
Discharge casing
Stage Casing
Shaft Seal Housing
Test time
Certificate
Test participation
33.00 bar.g
82.00 bar.g
82.00 bar.g
82.00 bar.g
2.0 min
Inspection cert. 3.1 to EN
10204
Non-witnessed
Performance curve
Number: 4002472206
Item no.:800
Date: 16/02/2016
Page: 4 / 7
Version no.: 19
Qmin
600
[m]
500
Qmax
400
173.0
10
[m/h]
20
30
40
50
60
10
[m/h]
20
30
40
50
60
10
[m/h]
20
30
40
50
60
10
[m/h]
20
30
Flow
40
50
60
NPSH req.
[m]
Efficiency
50
[%]
Power Input
100
[kW]
50
Curve data
Speed of rotation
Fluid density
Viscosity
Flow rate
Requested flow rate
Total developed head
Requested developed head
2979 rpm
954 kg/m
0.29 mm/s
32.80 m/h
32.80 m/h
587.64 m
587.58 m
Efficiency
Power absorbed
NPSH required
Curve number
Impeller diameter
Acceptance standard
68.3 %
73.24 kW
2.14 m
1777.407521/03 GG
173.0 mm
ISO 9906 class 3B
Installation plan
Number: 4002472206
Item no.:800
Date: 16/02/2016
Page: 5 / 7
Version no.: 19
140
1071
200
338
957
262
200
6
65
28
k7
DN1
DN2
200
445
80
380
1050
1329
717
250
2100
770
2600
930
2800
Baseplate
Design
Size
Material
Leakage drain baseplate
(8B)
Foundation bolts
Dimensions in mm
KSB-Motor
280M
90.00 kW
2
2979 rpm
0/360 (top)
Viewed from the drive
Connections
Suction nominal size DN1
Discharge nominal size DN2
Nominal pressure suct.
Rated pressure disch.
DN 80 / EN 1092-1
DN 50 / EN 1092-1
PN 25
PN 63
Coupling
Coupling manufacturer
Coupling type
Coupling size
Spacer
Flender
Eupex NH
160
140.0 mm
Weight net
Pump
Baseplate
Coupling
Coupling guard
Motor
Total
DIN 747
ISO 2768-m
EN735
ISO 13920-B
ISO 8062-CT9
250 kg
286 kg
15 kg
2 kg
762 kg
1315 kg
For auxiliary connections see
separate drawing.
Connection plan
Number: 4002472206
Item no.:800
Date: 16/02/2016
Page: 6 / 7
Version no.: 19
1M.2
1M.1
20E.1
20E.2
8B.1
8B.2
737D61BF
6B.1
6B.2
Connections
1M.1 Pressure gauge
connection
1M.2 Pressure gauge
connection
6B.1 Pumped liquid drain
6B.2 Pumped liquid drain
8B.1 Leakage drain
8B.2 Leakage drain
20E.1 Grease nipple
20E.2 Grease nipple
G 1/2
G 1/2
G 1/4
G 1/4
Rp 3/8
Rp 3/8
Data sheet
Number: 4002472206
Item no.: 810
Date: 16/02/2016
Page: 7 / 7
PumpMeter
Intelligent Pressure Transmitter PumpMeter - with on-site display of
operating point
Version no.: 19
General description:
Sensors:
Display values:
Ambient temperature:
-30C 80C (during transport, storage)
-10C 60C (operation)
Ambient conditions:
Type of protection: IP 65