Beruflich Dokumente
Kultur Dokumente
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It
offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the
application or to offload all Wi-Fi networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be
integrated with the sensors and other application specific devices through its GPIOs with
minimal development up-front and minimal loading during runtime. Its high degree of onchip integration allows for minimal external circuitry, and the entire solution, including
front-end module, is designed to occupy minimal PCB area.
Features
SDIO 2.0, SPI, UART
32-pin QFN package
Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
Integrated RISC processor, on-chip memory and external memory interfaces
Integrated MAC/baseband processors
Quality of Service management
I2S interface for high fidelity audio applications
On-chip low-dropout linear regulators for all internal supplies
Proprietary spurious-free clock generation architecture
Integrated WEP, TKIP, AES, and WAPI engines
Solutions
Supports APSD for optimal VoIP applications
Patented spurious noise cancellation algorithm for integration in SOC applications
Supports Bluetooth co-existence interface
Self-calibrated RF to ensure optimal performance under all operating conditions
Zero factory tuning
No external RF components
Specifications
802.11 b/g/n
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Integrated TR switch, balun, LNA, power amplifier and matching network
Integrated PLLs, regulators, DCXO and power management units
+19.5dBm output power in 802.11b mode
Power down leakage current of <10uA
Integrated low power 32-bit CPU could be used as application processor
SDIO 1.1/2.0, SPI, UART
STBC, 11 MIMO, 21 MIMO
A-MPDU & A-MSDU aggregation & 0.4ms guard interval
Wake up and transmit packets in < 2ms
Standby power consumption of < 1.0mW (DTIM3)
Help your development more easy.
ESP8266 Serial WIFI Module Community Forum>> Detail about ESP8266
1. High quality & low price
2. LWIP agreement
By Harvey Schneider
Now your Arduino can get on Wi-Fi without breaking the bank.
Use this module for your next Internet of Things project, home automation, or remote
sensor project.
This module adapts the ESP8226 IC for use over a serial connection using simple AT
commands.
No SPI interface or Know-How is required.
By Harvey Schneider
Warnings:
This module requires a 3.3 volt supply for VCC, and 3.3V logic. It is not 5V tolant. Connect
RX or TX on 5V Arduino will
destroy this module. You must use a logic level converter, or a 3.3V Arduino
The 3.3V supply on the Arduino Uno has inadequate current capabilit to power this module.
You must provide a separate,
higher 3.3V supply(about 300mA or better)
The ESP8225 module is very new on the market and support and documentation for it is
currently very limited.
By Harvey Schneider
By Harvey Schneider
Item Description
Features:
By Harvey Schneider
By Harvey Schneider
Description:
size:28mm(length)*12mm(width)*10mm(height)
main chip:18B20 temperature sensor
working Voltage: DC 5V
Features:
1.Resolution adjusting range:9-12 bytes
2.With installing hole, easy to install, hole diameter: 2.5mm
3.Temperature Range:-55~+125
4.Temperature measurement precision:0.5
5.Working Voltage: DC 5V
6. Digital signal output
By Harvey Schneider
1.
2.
3.
4.
5.
6.
7.
8.
9.
By Harvey Schneider
1. This is another great IIC/I2C/TWI/SPI Serial Interface. As the pin resources of Arduino controller
are limited, your project may be not able to use normal LCD shield after connected with a certain
quantity of sensors or SD card. However, with this I2C interface module, you will be able to
realize data display via only 2 wires. If you already has I2C devices in your project, this LCD
module actually cost no more resources at all. It is fantastic for Arduino based project.
2. I2C Address: 0X20~0X27 (the original address is 0X20,you can change it yourself)
3. Supply voltage: 5V
4. The backlight and contrast is adjusted by potentiometer
5. Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
6. I2C Address: 0x27 (I2C Address: 0X20~0X27 (the original address is 0X27,you can change it
yourself)
By Harvey Schneider
This product is a breakout board for Allegros A4988 DMOS Microstepping Driver with Translator and
Overcurrent Protection; please read the A4988 datasheet carefully before using this product. This stepper
motor driver lets you to operate bipolar stepper motors in full-, half-, quarter-, eighth-, and sixteenth-step
modes, with an output drive capacity of up to 35 V and 2 A.
The translator is the key to the easy implementation of the A4988. Simply inputting one pulse on the
STEP input drives the motor one microstep. There are no phase sequence tables, high frequency control
lines, or complex interfaces to program. The A4988 interface is an ideal fit for applications where a
complex microprocessor is unavailable or is overburdened.
Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver(More
generally, rewiring anything while it is powered is asking for trouble).
1. Maximum output current is 1A
2. Simple step and direction control interface
3. Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
4. Adjustable current control lets you set the maximum current output with a potentiometer, which lets
you use voltages above your stepper motors rated voltage toachieve higher step rates
5. Intelligent chopping control that automatically selects the correct current decay mode (fast decay or
slow decay)
6. Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
7. Short-to-ground and shorted-load protection
By Harvey Schneider
By Harvey Schneider