Beruflich Dokumente
Kultur Dokumente
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
1.40 KN/m
11.00
2.45
WIND LOAD DIAGRAM
Axial load is taken from load on piles P25/P26, Page 8 of pile layout design document
i)Dead + Live Load Combination:
Axial load on the column due to dead load ( 776.82+column wt))
Axial load on the column due to live load
Design Axial load on Column
Unsupported length of the column (11.00, from top of PB2 to top of column) about X - axis
Unsupported length of the column (11.00, from top of PB2 to top of column) about Y- axis
Width of column
Depth of column
eccentricity as per 25.4 of IS 456:2000 ec = l/500+D/30
About X - axis
About Y - axis
eccentricity as per 25.4 of IS 456:2000 ec = l/500+D/30
About X - axis
As per 39.2 of IS 456:2000 0.05 times lateral dimension
As per 39.2 of IS 456:2000 0.05 times lateral dimension
About Y - axis
Since the condition in 39.3 of IS 456:2000 is satisfied the column is designed as short column
Initial Moment due to minimum eccentricity(Design axial load x max(l/500+D/30, 20))
as per cluase25.4 and 39.2 of IS 456:2000
=
=
=
=
=
=
=
=
=
=
=
=
=
808.21 kN
436.98 kN
1830.66 kN
11.00 m
11.00 m
300.00 mm
600.00 mm
10.02
20.02
15.00
30.00
76.89 kNm
End conditions are assumed as follows as per Clause E 3 of Annex E and Table 28 of IS 456:2000
Cond.: Effectively held in position and restrained against rotation in one end, and the other partially
restrained against roatation but not held in position
1.50
Effective length factor from table 28 of IS 456:2000 is,
Actual length of the column (11.00, from top of PB2 to top of column)
=
11.00 m
Effective length of column
=
16.50 m
Width of column
=
300.00 mm
Depth of column
=
600.00 mm
Slenderness ratio for column
=
27.50
Calculation of Moment about major axis due to Slenderness:
As per Clause 39.7 of IS 456:2000
Max = (PuD/2000)*{lex/D}
=
415.33
k, Value of k is assumed as 1 for conservative side as per 39.7.1.1 of IS 456:2000
=
1.00
Additional moment about major axis due to Slenderness
= Max
=
415.33 kNm
Calculation of Moment about minor axis due to Slenderness:
Column is monolithic with wall for it's full height, effective length of the column about minor axis will be zero,
hence slenderness moment will be zero about minor axis. As both the initial moment and slenderness moment
about minor axis are zero we can design column as a uniaxially bent column.
Design Moment about major axis
=
492.22 kNm
=
10.17
Pu/bD
Mu/bd
=
4.56
From Chart No. Of SP16 Design aids for reinforced concrete to IS 456
100Asc/bD
=
1.802
Area of steel Asc
=
3243.51 mm2
Provide 8 No. T25.
Nominal Reinforcement about Minor Axis:
As the total reinforcement required is provided only on two faces, provide nominal reinforcement
of 0.2%(on each face) of cross section of column on other two faces of clolumn.
Area of steel on each face (0.20xwidthxdepth of column projecting out side of wall)
=
180.00 mm2
Provide 2 - T16 on each face.
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
=
=
=
300.00 mm
256.00 mm
300.00 mm
=
=
=
=
=
=
=
=
=
11.00 m
0.57 kN/sqm
2.78 m
1.58 kN/m
17.43 kN
147.29 kNm
808.21 kN
436.98 kN
1494.23 kN
66.49 kNm
End conditions are assumed as follows as per Clause E 3 of Annex E and Table 28 of IS 456:2000
Cond.: Effectively held in position and restrained against rotation in one end, and the other partially
restrained against roatation but not held in position
Effective length factor from table 28 of IS 456:2000 is,
Actual length of the column
=
Effective length of column
=
Width of column
=
Depth of column
=
Slenderness ratio for column
=
Calculation of Moment about major axis due to Slenderness:
As per Clause 39.7 of IS 456:2000
Max = (PuD/2000)*{lex/D}
=
k, Value of k is assumed as 1 for conservative side as per 39.7.1.1 of IS 456:2000
=
Additional moment about major axis due to Slenderness
= Max
=
Calculation of Moment about minor axis due to Slenderness:
Column is monolithic with wall for it's full height, effective length of the column about minor axis will be zero,
hence slenderness moment will be zero about minor axis. As both the initial moment and slenderness moment
about minor axis are zero we can design column as a uniaxially bent column.
Design Moment about major axis
=
Pu/bD
=
Mu/bd
=
From Chart No. Of SP16 Design aids for reinforced concrete to IS 456:2000
100Asc/bD
=
Area of steel Asc
=
Provide 6 No. T32.
Nominal Reinforcement about Minor Axis:
As the total reinforcement required is provided only on two faces, provide nominal reinforcement
of 0.2%(on each face) of cross section of column on other two faces of clolumn.
Area of steel on each face (0.20xwidthxdepth of column projecting out side of wall)
=
Provide 2 - T16 on each face.
Design of Lateral ties:
As per clause 26.5.3.2.c.2 of IS 456:2000, the diameter of the lateral bar should not be less
than one quarter of the diameter of largest compression bar or 6 mm whichever is more.
Provide T10 lateral ties.
Spacing of bars should not exceed least of the following:
i) Least lateral dimension
=
ii)16 times the dia of smallest compression bar to be tied
=
iii) 300mm
=
Provide T10 Lateral ties at 200 mm C/C.
CIVIL
1.50
12.25 m
18.38 m
300.00 mm
600.00 mm
30.63
420.43
1.00
420.43 kNm
597.17 kNm
8.30
5.53
2.615
4706.43 mm2
180.00 mm2
300.00 mm
256.00 mm
300.00 mm
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
11.00 m
0.57 kN/sqm
5.28 m
3.01 kN/m
33.07 kN
279.48 kNm
1193.00 kN
499.38 kN
2030.86 kN
85.30 kNm
1.50
11.00 m
16.50 m
400.00 mm
600.00 mm
27.50
460.75
1.00
460.75 kNm
796.12 kNm
8.46
5.53
2.616
6278.96 mm2
240.00 mm2
400.00 mm
256.00 mm
300.00 mm
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
=
=
=
=
=
=
11.00 m
0.57 kN/sqm
2.20 m
1.25 kN/m
13.79 kN
109.66 kNm
1.25 KN/m
11.00
2.45
=
=
=
=
=
=
=
153.53 KNm
700.00 mm
300.00 mm
50.00 mm
20.00 mm
640.00 mm
1.25 N/mm2
=
=
0.369
708.10 mm2
=
=
=
=
13.79 kN
19.31 kN
0.10 N/mm2
0.45 N/mm2
=
=
480.00 mm
192.00 mm
200.00 mm
11.42 mm
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
110.35 kNm
1.50
11.00 m
16.50 m
300.00 mm
700.00 mm
23.57
473.36
1.00
473.36 kNm
583.71 kNm
11.59
3.97
1.449
3042.42 mm2
180.00 mm2
300.00 mm
256.00 mm
300.00 mm
11.00 m
0.57 kN/sqm
4.35 m
2.48 kN/m
27.27 kN
216.83 kNm
967.11 kN
675.14 kN
1970.70 kN
94.27 kNm
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
1.50
12.25 m
18.38 m
300.00 mm
700.00 mm
26.25
475.28
1.00
475.28 kNm
735.48 kNm
9.38
5.00
2.163
4542.91 mm2
180.00 mm2
=
=
=
300.00 mm
256.00 mm
300.00 mm
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
7.5 COLUMN C7 :
i) Dead + Live Load Combination:
Axial load on the column due to dead load
=
Axial load on the column due to live load
=
Design Axial load on Column
=
Initial Moment due to minimum eccentricity(Design axial load x max(l/500+D/30, 20))
as per cluase25.4 and 39.2 of IS 456:2000
=
As the column is monolithic with wall for its full height, and at bottom it need not be designed
as a cantilever column.
End conditions are assumed as follows as per Clause E 3 of Annex E and Table 28 of IS 456:2000
Cond.: Effectively held in position and restrained against rotation in one end, and the other partially
restrained against roatation but not held in position
Effective length factor from table 28 of IS 456:2000 is,
Actual length of the column
=
Effective length of column
=
Width of column
=
Depth of column
=
Slenderness ratio for column
=
Calculation of Moment about major axis due to Slenderness:
As per Clause 39.7 of IS 456:2000
Max = (PuD/2000)*{lex/D}
=
k, Value of k is assumed as 1 for conservative side as per 39.7.1.1 of IS 456:2000
=
Additional moment about major axis due to Slenderness
= Max
=
Calculation of Moment about minor axis due to Slenderness:
Column is monolithic with wall for it's full height, effective length of the column about minor axis will be zero,
hence slenderness moment will be zero about minor axis. As both the initial moment and slenderness moment
about minor axis are zero we can design column as a uniaxially bent column.
Design Moment about major axis
=
Pu/bD
=
Mu/bd
=
From Chart No. Of SP16 Design aids for reinforced concrete to IS 456:2000
100Asc/bD
=
Area of steel Asc
=
Provide 6 No. T16.
Nominal Reinforcement about Minor Axis:
As the total reinforcement required is provided only on two faces, provide nominal reinforcement
of 0.2%(on each face) of cross section of column on other two faces of clolumn.
Area of steel on each face (0.20xwidthxdepth of column projecting out side of wall)
=
Provide 2 - T12 on each face.
Design of Lateral ties:
As per clause 26.5.3.2.c.2 of IS 456:2000, the diameter of the lateral bar should not be less
than one quarter of the diameter of largest compression bar or 6 mm whichever is more.
Provide T8 lateral ties.
Spacing of bars should not exceed least of the following:
i) Least lateral dimension
=
ii)16 times the dia of smallest compression bar to be tied
=
iii) 300mm
=
Provide T8 Lateral ties at 200 mm C/C.
375.04 kN
186.94 kN
824.16 kN
41.40 kNm
1.50
13.45 m
20.18 m
300.00 mm
700.00 mm
28.82
239.61
1.00
239.61 kNm
281.01 kNm
3.92
1.91
0.587
1232.53 mm2
180.00 mm2
300.00 mm
256.00 mm
300.00 mm
=
=
=
=
=
=
=
11.00 m
0.57 kN/sqm
2.75 m
1.57 kN/m
17.24 kN
137.08 kNm
375.04 kN
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
186.94 kN
674.38 kN
33.88 kNm
1.50
13.45 m
20.18 m
300.00 mm
700.00 mm
28.82
196.07
1.00
196.07 kNm
360.56 kNm
3.21
2.45
0.781
1639.93 mm2
180.00 mm2
300.00 mm
256.00 mm
300.00 mm
7.6 COLUMN C9 :
i)Dead + Live Load Combination:
Axial load on the column due to dead load(908.54+0.3*0.3*12.3*25)
Axial load on the column due to live load(No live load as column is starting from +4.00 m.level)
Design Axial load on Column
Initial Moment due to minimum eccentricity(Design axial load x max(l/500+D/30, 20))
as per cluase 3.8.2.4 of BS 8110 Part-1
As the column is monolithic with wall for its full height, and at bottom it need not be designed
as a cantilever column.
End conditions are assumed as follows as per Clause E 3 of Annex E and Table 28 of IS 456:2000
Cond.: Effectively held in position and restrained against rotation in one end, and the other partially
restrained against roatation but not held in position
Effective length factor from table 28 of IS 456:2000 is,
Actual length of the column (11.00, from top of PB3 to top of column)
Effective length of column
10
=
=
=
936.22 kN
413.14 kN
1971.73 kN
82.81 kNm
=
=
1.50
11.00 m
16.50 m
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
Width of column
Depth of column
Slenderness ratio for column
Calculation of Moment about major axis due to Slenderness:
As per Clause 39.7 of IS 456:2000
Max = (PuD/2000)*{lex/D}
k, Value of k is assumed as 1 for conservative side as per 39.7.1.1 of IS 456:2000
Additional moment about major axis due to Slenderness
= Max
Design Moment about major axis
Pu/bD
Mu/bd
From Chart No. Of SP16 Design aids for reinforced concrete to IS 456:2000
100Asc/bD
Area of steel Asc
Provide 10-T25
Nominal Reinforcement about Minor Axis:
As the total reinforcement required is provided only on two faces, provide nominal reinforcement
of 0.2%(on each face) of cross section of column on other two faces of clolumn.
Area of steel on each face (0.20xwidthxdepth of column projecting out side of wall)
Provide 2 - T12 on each face.
Design of Lateral ties:
As per clause 26.5.3.2.c.2 of IS 456:2000, the diameter of the lateral bar should not be less
than one quarter of the diameter of largest compression bar or 6 mm whichever is more.
Provide T8 lateral ties.
Spacing of bars should not exceed least of the following:
i) Least lateral dimension
ii)16 times the dia of smallest compression bar to be tied
iii) 300mm
Provide T8 Lateral ties at 200 mm C/C.
ii)Dead + Live + Wind Load Combination:
Wind load Calculations:
Height for which wind is acting
Intensty of wind Pressure
Maximum width of column contributing wind load to column
Wind load for metre height of wall
Total wind force acting on column
Initial Moment at bottom of column
Axial load on the column due to dead load
Axial load on the column due to live load
Design Axial load on Column
Initial Moment due to minimum eccentricity(Design axial load x max(l/500+D/30, 20))
as per cluase25.4 and 39.2 of IS 456:2000
As the column is monolithic with wall for its full height, and at bottom it need not be designed
as a cantilever column.
End conditions are assumed as follows as per Clause E 3 of Annex E and Table 28 of IS 456:2000
Cond.: Effectively held in position and restrained against rotation in one end, and the other partially
restrained against roatation but not held in position
Effective length factor from table 28 of IS 456:2000 is,
Actual length of the column
Effective length of column
Providing 300x600 mm column
Width of column
Depth of column
Slenderness ratio for column
=
=
=
300.00 mm
600.00 mm
27.50
=
=
=
=
=
=
447.34
1.00
447.34 kNm
530.15 kNm
10.95
4.91
=
=
2.075
3734.98 mm2
180.00 mm2
=
=
=
300.00 mm
256.00 mm
300.00 mm
11
CIVIL
=
=
=
=
=
=
=
=
=
11.00 m
0.57 kN/sqm
2.78 m
1.58 kN/m
17.43 kN
118.53 kNm
936.22 kN
413.14 kN
1619.23 kN
68.01 kNm
=
=
1.50
11.00 m
16.50 m
=
=
=
300.00 mm
600.00 mm
27.50
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
CIVIL
=
=
=
=
=
=
367.36
1.00
367.36 kNm
509.60 kNm
9.00
4.72
=
=
1.919
3453.38 mm2
180.00 mm2
=
=
=
300.00 mm
256.00 mm
300.00 mm
=
=
=
=
=
=
7.00 m
0.57 kN/sqm
5.95 m
3.39 kN/m
23.74 kN
83.09 kNm
3.39 KN/m
7.00
12
=
=
=
=
=
=
=
116.33 KNm
600.00 mm
300.00 mm
50.00 mm
20.00 mm
540.00 mm
1.33 N/mm2
InfoMile Solutions
PROJECT : SKS PRAI - 350 MW CCGT POWER PLANT
Rev
Designed by
Checked by
Date
Page
of
Area
Dept
% Steel
Area of steel
Provide 3 No. T16 (on each face)
=
=
=
=
=
=
=
=
=
=
13
CIVIL
0.394
638.76 mm2
23.74 kN
33.24 kN
0.21 N/mm2
0.44 N/mm2
302.32 mm
405.00 mm
300.00 mm
256.00 mm
300.00 mm
12.00 mm
Infomile Solutions
PROJECT
Rev
Designed
Checked
Approved
Page of
DOC TITLE:
XX
XXX
XXX
DOC. NO:
Grade of concrete Fck
Department
25
415
40
Grade of steel Fy
Clear Cover C
b
mm
400
Reinforcemen
End
ef.
lox
lex
loy
ley
ley/b
Pu
Mux
Mix
Muy
Miy
Slenderness Moments
k
Max
###
kMax
###
May
###
Total moments
k May
###
Mx
kNm
###
Equivalent
Uniaxial Moment
Mx' or My'
My
kNm Pu/bDfcu
###
0.08
X- Major Axis
D=Depth of column
My
Pu=Axial Load
Mux=Moment due to Design ultimate loads about X Axis
Y-Minor Axis
Mx'/bd2
% steel Asc
or
My'/Db2
mm2
kNm
kN/mm2
###
#VALUE!
2.08 #VALUE!
b=Breadth of column
Reinforcement
Pu/bd
1.80
4320
Lateral Ties
Sv
Dia
8
256