Beruflich Dokumente
Kultur Dokumente
Contents
1
INTRODUCTION
2.1
2.2
2.3
2.3.2
2.3.3
2.3.4
2.3.5
2.3.6
2.3.7
23
3.1
3.2
(Rev. 0)
APOLLO EZ
3.2.7
3.2.8
3.2.9
3.3
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
3.3.7
45
4.1
4.2
APOLLO EZ
ii
(Rev. 0)
4.3
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
iii
APOLLO EZ
APOLLO EZ
iv
(Rev. 0)
INTRODUCTION
This Manual includes the interconnections list, the hardware and
software configuration for a typical radiological room using a generator
G 100 R/F-A.
For the use of this generator with different configurations of room and for
X-ray tube and AEC calibration, please make reference to the
G 100 R/F-A Service Manual and equipment you have to connect with.
(Rev. 0)
APOLLO EZ
APOLLO EZ
(Rev. 0)
Apollo EZ
I.A.E. X-ray tube type
Three field solid state AEC
Standard I.I. CCD N23.
G 100 R/F-A
Chest Stand VD3 35x43 with motorised foot rest (See Note)
Three field solid state AEC.
Receptor configuration
Receptor 1: Apollo EZ Spot Film Device Tube 1
Receptor 2: Direct X-ray from console Tube 1
Receptor 3: Chest Stand VD3 35x43 Tube 1 (See Note)
NOTE:
When the Generator is supplied with "Falling load" feature, the GalKey
U29 # 73594213 is installed on CPU board.
The Falling Load option it is not available on the receptors where the
"SERIAL" exposure is enable (paragraph 2.3.4 - Image Receptor
Programming Worksheet: "SERIAL=YES"); whenever the Falling Load has
to be activated on the Spot Film Device receptor, the SERIAL parameter
has to be set to "NO".
In case Falling Load feature and SERIAL exposure are required will be
necessary to create for each a dedicated receptor.
NOTE:
Reference to the Chest Stand VD3 35x43 with motorized foot rest is made
in order to allows the installer to record the necessary information for the
hardware interface among Generator and Potter Bucky.
(Rev. 0)
APOLLO EZ
2.1
Main
Power Supply
Generator
Terminals
G 100 R/F
ROOM INTERFACE BOARD
TB7.1 (0 Vac)
* INSTALLATION KIT
230Vac AUXILIARY CONTACTOR
V.S.M. cod.4291515200
G 100 R/F
ROOM INTERFACE BOARD
TB10.1 (220 Vac)
R S T
APOLLO EZ
Terminals R-S-T
R S
CHEST STAND
Terminal X1 (**)
(*) If this remote controlled switch is not available use a remote controlled
switch with the following characteristics:
Coil:
220-230 Vac 50 Hz
230-240 Vac 60 Hz
APOLLO EZ
(Rev. 0)
2.2
2.2.1
APOLLO EZ
Description
Generator
Terminal
Terminal
Description
X27.15
TB6.9
Remote exposure
(Room Interface Board)
X27.3
TB6.7
Remote prep
(Room Interface Board)
X-ray
request
(2 step)
X27.16
TB2.11
Bucky 1 select
(Room Interface Board)
Common
0VS
X0.20
TB6.1
Ale output
(Room Interface Board)
TB6.11
Spare output
(Room Interface Board)
TB6.2
Ale output
(Room Interface Board)
TB3.6
Tomo exposure
(Room Interface Board)
X-ray ON
from
generator
X0.13
Generator
ready
X0.12
TB2.12
Bucky 1 select
(Room Interface Board)
Tomo speed
1-2-3-4
X27.4
X27.1
X27.14
X27.17
TB3.4
SFD
selection
X0.15
TB6.12
Spare output
(Room Interface Board)
Safety
switch
X0.9
J17.1
Safety switch
(Generator Interface PWB)
Safety
switch
X0.11
J17.2
Safety switch
(Generator Interface PWB)
(Rev. 0)
APOLLO EZ
2.2.2
Generator
Description
Terminal
Pcb A2
Description
TB6.5
X2.3
Fluoro
0Vdc
(Generator Interface PWB)
J7.7
X2.1
0Vdc
Proportional dc
(Generator Interface PWB)
J7.12
X2.2
Analog kV auto
APOLLO EZ
Wire n
(Rev. 0)
2.2.3
APOLLO EZ
Description
Terminal
Common
Wire n
Pcb A1
Description
4 fields
3 fields
X28.1
X4.4
X4.4
Common
Medium field
X28.2
X4.2
X4.1
Medium zoom
Minimum field
X28.14
X4.3
X4.2
Maximum field
X28.15
X4.1
N.C.
Power supply
X0.2
Power supply
Power supply
S3
X0.1
Power supply
X0.3
Ground
Ground
APOLLO EZ
Description
0 Vs common
(Rev. 0)
Maximum
zoom
Minimum
zoom
Wire n
Pcb A2
Description
X28.18
X3.3
Fluoro request
X28.4
X3.4
Inv
X28.16
X3.5
Inv
X28.3
X3.2
0 Vs common
APOLLO EZ
Monitor interface
2.2.4
Description
Pcb A2
Wire n
Plug
Description
0 Vs common
X4.1
Green
0V
0 Vs common
Monitor L.I.H.
visualization
X4.5
White
LI
Monitor L.I.H.
visualization
APOLLO EZ
(Rev. 0)
2.2.5
Generator
AEC board
(solid state chamber)
type 737992
AEC device 1
connecting cable
Description Terminal
Wire
Description
Anode (L)
J11.1
Pink
Anode Left
Cath (L)
J11.2
Grey
Cathode Left
Anode (M)
J11.3
White
Anode Middle
Cath (M)
J11.4
Brown
Cathode Middle
Anode (R)
J11.5
Green
Anode Right
Cath (R)
J11.6
Yellow
Cathode Right
Ground
J11.7
Shield
Ground
(Rev. 0)
APOLLO EZ
2.2.6
Generator
X-ray tube
Description
Terminal
Main
Terminal
Description
Tube 1
Principal
Shift
Tube 1
Auxiliary
Common
Tube 1
Common
Ground
Tube 1
Ground
Thermal switch
Tube 1
Thermal switch
Thermal switch
Tube 1
Thermal switch
APOLLO EZ
Wire n
10
(Rev. 0)
2.2.7
Terminal
X-ray request
Generator
Wire n
Terminal
Description
X1.B1
TB1.11
Bucky 3 select
X-ray request
X1.B2
TB1.12
Bucky 3 select
Potter reply
X1.X
TB2.5
Bucky contacts
Potter reply
X1.X
TB2.4
Bucky contacts
WARNING:
The voltage selected on TB1.11 and TB1.12 is 24 Vdc. Refer to the Chest
Stand VD3 35x43 Technical and User's Manual for the Bucky start
voltage setting.
(Rev. 0)
11
APOLLO EZ
2.2.8
Generator
AEC board
(solid state chamber)
type 737992
AEC device 2
connecting cable
Description Terminal
Wire
Description
Anode (L)
J12.1
Pink
Anode Left
Cath (L)
J12.2
Grey
Cathode Left
Anode (M)
J12.3
White
Anode Middle
Cath (M)
J12.4
Brown
Cathode Middle
Anode (R)
J12.5
Green
Anode Right
Cath (R)
J12.6
Yellow
Cathode Right
Ground
J12.7
Shield
Ground
APOLLO EZ
12
(Rev. 0)
2.2.9
2.2.9.1
2.2.9.2
2.2.9.3
JW2:
JW4:
JW7:
JW8:
TB8.1 TB11.5:
TB4.8 TB4.9:
JW1:
JW2:
JW3:
JW10:
JW11:
JW12:
JW13:
JW14:
JW15:
JW21:
12
12/
12/
12/
23
Open
Open
12/
12/
2-3
34
34
34
34
34
NOTE:
The configuration of the Jumpers not listed in the previous tables is not
relevant for this system integration.
(Rev. 0)
13
APOLLO EZ
2.2.9.4
Accessories connection
Generator
Accessory
Description
Terminal
Wire n
Description
TB4.4
Door contact
TB4.5
Door contact
Room light 0V
(Room Interface board)
TB7
Generator ON lamp
(white lamp)
(*)
Generator ON lamp
(white lamp)
TB4.11
X-ray ON lamp
(red lamp)
TB4.12
X-ray ON lamp
(red lamp)
(*) TB10 for 220V ac / TB9 for 110V ac / TB8 for 24V dc
NOTE:
Remove jumper JW13 on Room Inteface Board.
APOLLO EZ
14
(Rev. 0)
2.3
2.3.1
Tube selection
Prior to beginning tube calibration, the tube used in the installation must
be properly selected, and generator limits should be programmed.
2.3.1.1
(Rev. 0)
15
APOLLO EZ
2.3.1.2
2.3.1.3
APOLLO EZ
16
(Rev. 0)
2.3.2
AEC set-up
The installation of the AEC devices and their calibration are covered in
the Generator Service Manual, chapter 3E - Automatic exposure control
(AEC) calibration.
2.3.3
Fluoro set-up
NOTE:
The Fluoro set-up data must be set in according with the X-ray tube
technical specification.
The following tables meets the Fluoro set-up request in according with
most of the X-ray tube supplied by Villa Sistemi Medicali; during the
installation could be necessary to optimize the set-up.
The installation of the ABS device and his calibration are covered in the
Generator Service Manual, chapter 3 - Automatic brightness stabilisation
(ABS) calibration.
The next table show the standard parameters usually set.
FLUORO SET-UP
FL TIMER:
5 Min
MIN FLUORO KV:
40
MAX FLUORO KV:
120
II MODES:
0
FL ABS:
ON
FL ABS DEFAULT: NONE
FL/RAD KV DEF: NONE
FL/RAD KV CURVES
SID COMP
FL SETUP
Not Used
Not Used
FL ABS SETUP
(Rev. 0)
17
ABS LEVEL 0:
ABS LEVEL 1:
ABS LEVEL 2:
ABS LEVEL 3:
SIGNAL GAIN
ABS GAIN
ABS DEADBAND
ABD DELAY
ABS START KV
1.00 V
1.60 V
1.10 V
1.60 V
10
20
3%
150 mS
75
APOLLO EZ
FL ABS CURVE
FL ABS CURVE 1:
ON
40KV:
0.5 mA
50 KV:
1.0 mA
60 KV:
1.6 mA
70 KV:
2.1 mA
80 KV:
2.7 mA
90 KV:
3.2 mA
100 KV:
3.8 mA
110 KV:
4.4 mA
120 KV:
5.0 mA
5.0mA
125 KV:
* FL MAN DL *
40KV:
0.5 mA
50 KV:
1.0 mA
60 KV:
1.6 mA
70 KV:
2.1 mA
80 KV:
2.7 mA
90 KV:
3.2 mA
100 KV:
3.8 mA
110 KV:
4.4 mA
120KV:
5.0 mA
5.0 mA
125 KV:
FL DOSE LIMIT
* FL ABS DL *
HLF SETUP
PF SETUP
FL II COMP
Not Used
PF:
40KV:
5.0 mA
50 KV:
5.0 mA
60 KV:
5.0 mA
70 KV:
5.0 mA
80 KV:
5.0 mA
90 KV:
5.0 mA
100 KV:
5.0 mA
110 KV:
5.0 mA
120KV:
5.0 mA
125 KV:
5.0 mA
Not Used
OFF
NOTE:
The Pulsed Fluoro set-up is not relevant for this system integration
because the function is not available with the N23 CCD camera.
APOLLO EZ
18
(Rev. 0)
2.3.4
RECEPTOR
1
RECEPTOR
2
RECEPTOR
3
RECEPTOR
4
RECEPTOR
5
RECEPTOR
6
RECEPTOR
NAME
TUBE
NONE
NONE
NONE
TOMO
YES
NO
NO
NO
NO
NO
FLUORO
YES
NO
NO
NO
NO
NO
SERIAL
YES
NO
NO
NO
NO
NO
INTERFACE
OPTS
FUNCTIONAL
OPTS
FLUORO
HANG
30 SEC
30 SEC
30 SEC
30 SEC
30 SEC
30 SEC
RAD HANG
0 SEC
0 SEC
0 SEC
0 SEC
0 SEC
0 SEC
LAST IMAGE
HOLD
40 Ms
40 Ms
40 Ms
40 Ms
40 Ms
40 Ms
MEMORY
NO
NO
NO
NO
NO
NO
REM TOMO
BUT
2500 Ms
2500 Ms
2500 Ms
2500 Ms
2500 Ms
2500 Ms
SF/LF
SWITCH
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AEC BACKUP
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
AEC BACKUP
MAS
500
500
500
500
500
500
AEC BACKUP
MS
3200
3200
3200
3200
3200
3200
AEC
CHANNEL
AEC LOCK
EXPS
RECEPTOR
SYM
NOTE:
Receptor 3 has to be programmed only if Chest Stand with Potter Bucky
and AEC device is present.
(Rev. 0)
19
APOLLO EZ
2.3.5
FUNCTIONS
STANDBY
PREP
GEN RDY
RAD EXP
FLUORO EXP
ON
--------OFF
----ON
----OFF
OFF
OFF
OFF
ON
OFF
ON
-----
--------ON
----------------OFF
OFF
----OFF
ON
OFF
ON
-----
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
***INPUTS***
REMOTE EXP
REMOTE PREP
REMOTE FL. EXP
CONSOLE EXP
CONSOLE PREP
TOMO EXP
REM. TOMO SEL
I/I SAFETY
COLL. ITLK
BUCKY CONTACTS
SPARE
THERMAL SW 1
THERMAL SW 2
DOOR ITLK
MULTI SPOT EXP
------------------------ON
------------OFF
ON
OFF
OFF
OFF
OFF
ON
----OFF
OFF
--------OFF
OFF
----OFF
ON
OFF
ON
-----
-------------------------------------------------------------
***OUTPUTS***
BKY 1 SELECT
BKY 2 SELECT
BKY 3 SELECT
TOMO/BKY 4 SEL
TOMO/BKY START
ALE
COLL. BYPASS
ROOM LIGHT
SPARE
APOLLO EZ
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
20
(Rev. 0)
2.3.6
FUNCTIONS
STANDBY
PREP
GEN RDY
RAD EXP
FLUORO EXP
ON
--------OFF
----OFF
----OFF
OFF
OFF
OFF
ON
OFF
ON
-----
--------OFF
----------------OFF
OFF
----OFF
ON
OFF
ON
-----
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
***INPUTS***
REMOTE EXP
REMOTE PREP
REMOTE FL. EXP
CONSOLE EXP
CONSOLE PREP
TOMO EXP
REM. TOMO SEL
I/I SAFETY
COLL. ITLK
BUCKY CONTACTS
SPARE
THERMAL SW 1
THERMAL SW 2
DOOR ITLK
MULTI SPOT EXP
------------------------OFF
------------OFF
ON
OFF
OFF
OFF
OFF
ON
----OFF
OFF
--------OFF
OFF
----OFF
ON
OFF
ON
-----
-------------------------------------------------------------
***OUTPUTS***
BKY 1 SELECT
BKY 2 SELECT
BKY 3 SELECT
TOMO/BKY 4 SEL
TOMO/BKY START
ALE
COLL. BYPASS
ROOM LIGHT
SPARE
(Rev. 0)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
21
APOLLO EZ
2.3.7
FUNCTIONS
STANDBY
PREP
GEN RDY
RAD EXP
FLUORO EXP
OFF
--------ON
----OFF
----OFF
OFF
ON
OFF
ON
OFF
ON
-----
--------OFF
----------------OFF
OFF
----OFF
ON
OFF
ON
-----
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
***INPUTS***
REMOTE EXP
REMOTE PREP
REMOTE FL. EXP
CONSOLE EXP
CONSOLE PREP
TOMO EXP
REM. TOMO SEL
I/I SAFETY
COLL. ITLK
BUCKY CONTACTS
SPARE
THERMAL SW 1
THERMAL SW 2
DOOR ITLK
MULTI SPOT EXP
------------------------OFF
------------OFF
ON
OFF
OFF
OFF
OFF
OFF
----OFF
ON
--------OFF
OFF
----OFF
ON
OFF
ON
-----
-------------------------------------------------------------
***OUTPUTS***
BKY 1 SELECT
BKY 2 SELECT
BKY 3 SELECT
TOMO/BKY 4 SEL
TOMO/BKY START
ALE
COLL. BYPASS
ROOM LIGHT
SPARE
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
NOTE:
The configuration of the Receptor 3 I/O has to be made only if the Chest
Stand with Potter Bucky is present.
APOLLO EZ
22
(Rev. 0)
Apollo EZ
Chest Stand VD3 35x43 with motorised foot rest (See Note)
Receptor configuration
Receptor 1: Apollo EZ Spot Film Device Tube 1
Receptor 2: Direct X-ray from console Tube 1
Receptor 3: Chest Stand VD3 35x43 Tube 1 (See Note)
NOTE:
When the Generator is supplied with "Falling load" feature, the GalKey
U29 # 73594213 is installed on CPU board.
The Falling Load option it is not available on the receptors where the
"SERIAL" exposure is enable (paragraph 3.3.4 - Image Receptor
Programming Worksheet: "SERIAL=YES"); whenever the Falling Load has
to be activated on the Spot Film Device receptor, the SERIAL parameter
has to be set to "NO".
In case Falling Load feature and SERIAL exposure are required will be
necessary to create for each a dedicated receptor.
NOTE:
Reference to the Chest Stand VD3 35x43 with motorized foot rest is made
in order to allows the installer to record the necessary information for the
hardware interface among G 100 R/F-A and Potter Bucky.
(Rev. 0)
23
APOLLO EZ
3.1
Main
Power Supply
Generator
Terminals
G 100 R/F
ROOM INTERFACE BOARD
TB7.1 (0 Vac)
* INSTALLATION KIT
230Vac AUXILIARY CONTACTOR
V.S.M. cod.4291515200
G 100 R/F
ROOM INTERFACE BOARD
TB10.1 (220 Vac)
R S T
APOLLO EZ
Terminals R-S-T
R S
CHEST STAND
Terminal X1 (**)
(*) If this remote controlled switch is not available use a remote controlled
switch with the following characteristics:
Coil:
220-230 Vac 50 Hz
230-240 Vac 60 Hz
APOLLO EZ
24
(Rev. 0)
3.2
3.2.1
APOLLO EZ
Description
Terminal
G 100 R/F-A
Wire n
Terminal
Description
X27.15
TB6.9
Remote Exposure
(Room Interface Board)
X27.3
TB6.7
Preparation radiography
(Room Interface Board)
Common
0Vdc
X0.20
TB6.11
Spare Output
(Room Interface Board)
X-ray ON
from
Generator
X0.13
J6.21
X-ray ON
(Table Digital Interface board)
Generator
ready
X0.12
J6.22
Generator ready
(Table Digital Interface board)
Spot Film
Device
selection
X0.15
TB6.12
Spare Output
(Room Interface Board)
Safety switch
X0.9
J17.1
Safety switch
(Generator Interface PWB)
Safety switch
X0.11
J17.2
Safety switch
(Generator Interface PWB)
Alarm
X-ray ON
X27.7
(see Note)
J7.6
X-ray OFF
(Table Digital Interface board)
Fluoro
Man/Auto
X27.20
J6.1
Fluoro Man/Auto
(Table Digital Interface board)
NOTE:
During the auto calibration of the X-ray tube it is required to make the
jumper between J7.6 and J6.2 (force terminal J7.6 at 0Vdc).
It is important to remove the jumper at the end of the X-ray tube
auto calibration.
(Rev. 0)
25
APOLLO EZ
APOLLO EZ
Description
Terminal
Vref. Anal.
Fluoro
X27.11
Tomo
Speed 1
X27.4
Tomo
Speed 2
X27.1
Tomo
Speed 3
X27.14
Tomo
Speed 4
G 100 R/F-A
Terminal
Description
J6.7
J6.3
Tomo Speed 1
(Table Digital Interface board)
X27.17
J6.4
Tomo Speed 2
(Table Digital Interface board)
Tomo 7
X27.5
J7.1
Tomo Angle 7
(Table Digital Interface board)
Tomo 20
X27.18
J7.3
Tomo Angle 20
(Table Digital Interface board)
Tomo 30
X27.6
J7.4
Tomo Angle 30
(Table Digital Interface board)
Tomo 45
X27.19
J7.5
Tomo Angle 45
(Table Digital Interface board)
Common 0V
X27.22
J6.2
Signal Ground
(Table Digital Interface board)
Fluoro Man
kV analog 0V
X27.23
J6.23
Signal Ground
(Table Digital Interface board)
J7.2
Signal Ground
(Table Digital Interface board)
J7.7
Chassis Ground
(Table Digital Interface board)
J7.20
Chassis Ground
(Table Digital Interface board)
APOLLO EZ
Wire n
26
(Rev. 0)
3.2.2
G 100 R/F-A
Description
Terminal
Pcb A2
Description
TB6.5
X2.3
Fluoro
L.I.H.
(Table Digital Interface
board)
J6.17
X2.4
Proportional dc
(Table Digital Interface
board)
J7.21
X2.1
Analog kV auto
0Vdc
(Table Digital Interface
board)
J7.2
X2.2
0Vdc
SYNC
(Table Digital Interface
board)
J7.24
X4.5
SYNC
P.F. request
(Table Digital Interface
board)
J6.22
X4.6
Pulsed Fluoro
(Rev. 0)
Wire n
27
APOLLO EZ
3.2.3
APOLLO EZ
Description
Terminal
Common
Wire n
Pcb A1
Description
4 fields
3 fields
X28.1
X4.4
X4.4
Common
Medium field
X28.2
X4.2
X4.1
Medium zoom
Minimum field
X28.14
X4.3
X4.2
Maximum field
X28.15
X4.1
N.C.
Power supply
X0.2
Power supply
Power supply
S3
X0.1
Power supply
X0.3
Ground
Ground
APOLLO EZ
Maximum
zoom
Minimum
zoom
Description
Terminal
R.O.I.
X28.8
(see Note)
Fluoro call
Wire n
Pcb A2
Description
X2.15
R.O.I.
X2.11
Recursive Filter X0
X28.18
X2.5
Fluoro call
Vertical image
inversion
X28.16
X2.8
Vertical image
inversion
Horizontal image
inversion
X28.4
X2.9
Horizontal image
inversion
Recursive Filter X4
X28.21
(see Note)
X2.12
Recursive Filter X4
Recursive Filter X8
X28.9
(see Note)
X2.13
Recursive Filter X8
Common 0V
X28.3
X4.10
Common 0V
Common 0V
X28.22
NOTE:
Depending by selection of the Apollo EZ set-up, cell 246 X28.8 output
can drive R.O.I. or Recursive Filter. In the first case X28.21 and X28.9
are disabled, in the second case are enabled.
APOLLO EZ
28
(Rev. 0)
Monitor interface
3.2.4
Description
Pcb A2
Wire n
Plug
Description
Monitor L.I.H.
visualization
X4.2
White
LI
Monitor L.I.H.
visualization
0 Vs common
X4.10
Green
0V
0 Vs common
(Rev. 0)
29
APOLLO EZ
3.2.5
G100 R/F-A
AEC board
(solid state chamber)
type 737992
AEC device 1
connecting cable
Description Terminal
Wire
Description
Anode (L)
J11.1
Pink
Anode Left
Cath (L)
J11.2
Grey
Cathode Left
Anode (M)
J11.3
White
Anode Middle
Cath (M)
J11.4
Brown
Cathode Middle
Anode (R)
J11.5
Green
Anode Right
Cath (R)
J11.6
Yellow
Cathode Right
Ground
J11.7
Shield
Ground
APOLLO EZ
30
(Rev. 0)
3.2.6
G 100 R/F-A
X-ray tube
Description
Terminal
Main
Terminal
Description
Tube 1
Principal
Shift
Tube 1
Auxiliary
Common
Tube 1
Common
Ground
Tube 1
Ground
Thermal switch
Tube 1
Thermal switch
Thermal switch
Tube 1
Thermal switch
(Rev. 0)
Wire n
31
APOLLO EZ
3.2.7
Terminal
X-ray request
G 100 R/F-A
Wire n
Terminal
Description
X1.B1
TB1.11
Bucky 3 select
X-ray request
X1.B2
TB1.12
Bucky 3 select
Potter reply
X1.X
TB2.5
Bucky contacts
Potter reply
X1.X
TB2.4
Bucky contacts
WARNING:
The voltage selected on TB1.11 and TB1.12 is 24 Vdc. Refer to the Chest
Stand VD3 35x43 Technical and User's Manual for the Bucky start
voltage setting.
APOLLO EZ
32
(Rev. 0)
3.2.8
G100 R/F-A
AEC board
(solid state chamber)
type 737992
AEC device 2
connecting cable
Description Terminal
Wire
Description
Anode (L)
J12.1
Pink
Anode Left
Cath (L)
J12.2
Grey
Cathode Left
Anode (M)
J12.3
White
Anode Middle
Cath (M)
J12.4
Brown
Cathode Middle
Anode (R)
J12.5
Green
Anode Right
Cath (R)
J12.6
Yellow
Cathode Right
Ground
J12.7
Shield
Ground
(Rev. 0)
33
APOLLO EZ
3.2.9
3.2.9.1
3.2.9.2
3.2.9.3
JW2:
JW3:
JW4:
JW8:
TB8.1 TB11.5
TB4.8 TB4.9:
JW1:
JW2:
JW3:
JW4:
JW5:
JW6:
JW7:
JW8:
JW9:
JW10:
JW11:
JW12:
12
12/
12/
Open
Close
12/
12/
12/
12/
12/
23
Open
34
34
3
3
3
3
3
4
4
4
4
4
JW13:
JW14:
JW15:
JW19:
JW20:
JW21:
JW22:
JW24:
JW25:
JW26:
JW27:
JW28:
Open
1 2 / 3 4
12/34
23
Close
12
23
Close
Close
Close
Close
Open
NOTE:
The configuration of the Jumpers not listed in the previous tables is not
relevant for this system integration.
APOLLO EZ
34
(Rev. 0)
3.2.9.4
3.2.9.5
SW1-1:
SW1-2:
SW1-3:
SW1-4:
OFF
OFF
ON
OFF
SW1-5:
SW1-6:
SW1-7:
SW1-8:
ON
OFF
OFF
OFF
Accessories connection
Generator
Accessory
Description
Terminal
Wire n
Description
TB4.4
Door contact
TB4.5
Door contact
Room light 0V
(Room Interface board)
TB7
Generator ON lamp
(white lamp)
(*)
Generator ON lamp
(white lamp)
TB4.11
X-ray ON lamp
(red lamp)
TB4.12
X-ray ON lamp
(red lamp)
(*) TB10 for 220V ac / TB9 for 110V ac / TB8 for 24V dc
NOTE:
Remove jumper JW13 on Room Inteface Board.
(Rev. 0)
35
APOLLO EZ
3.3
3.3.1
Tube selection
Prior to beginning tube calibration, the tube used in the installation must
be properly selected, and generator limits should be programmed.
3.3.1.1
APOLLO EZ
36
(Rev. 0)
3.3.1.2
3.3.1.3
(Rev. 0)
37
APOLLO EZ
3.3.2
AEC set-up
The installation of the AEC devices and their calibration are covered in
the G 100 R/F-A Service Manual, chapter 3E - Automatic exposure
control (AEC) calibration.
3.3.3
Fluoro set-up
NOTE:
The Fluoro set-up data must be set in according with the X-ray tube
technical specification.
The following tables meets the Fluoro set-up request in according with
most of the X-ray tube supplied by Villa Sistemi Medicali; during the
installation could be necessary to optimize the set-up.
The installation of the ABS device and his calibration are covered in the
G 100 R/F-A Service Manual, chapter 3 - Automatic brightness
stabilisation (ABS) calibration.
The next table show the standard parameters usually set.
FLUORO SET-UP
FL TIMER:
5 Min
MIN FLUORO KV:
40
MAX FLUORO KV:
120
II MODES:
0
FL ABS:
ON
FL ABS DEFAULT: NONE
FL/RAD KV DEF:
NONE
FL/RAD KV CURVES
SID COMP
FL SETUP
Not Used
Not Used
FL ABS SETUP
APOLLO EZ
38
ABS LEVEL 0:
ABS LEVEL 1:
ABS LEVEL 2:
ABS LEVEL 3:
SIGNAL GAIN
ABS GAIN
ABS DEADBAND
ABD DELAY
ABS START KV
1.00 V
4.00 V
1.10 V
1.60 V
3
10
30%
150 mS
75
(Rev. 0)
FL ABS CURVE
FL DOSE LIMIT
HLF SETUP
(Rev. 0)
FL II COMP
Not Enable
39
FL ABS CURVE 1:
ON
40KV:
0.5 mA
50 KV:
1.0 mA
60 KV:
1.6 mA
70 KV:
2.1 mA
80 KV:
2.7 mA
90 KV:
3.2 mA
100 KV:
3.8 mA
110 KV:
4.4 mA
120 KV:
5.0 mA
5.0mA
125 KV:
* FL MAN DL *
40KV:
0.5 mA
50 KV:
1.0 mA
60 KV:
1.6 mA
70 KV:
2.1 mA
80 KV:
2.7 mA
90 KV:
3.2 mA
100 KV:
3.8 mA
110 KV:
4.4 mA
120KV:
5.0 mA
5.0mA
125 KV:
* FL ABS DL *
40KV:
5.0 mA
50 KV:
5.0 mA
60 KV:
5.0 mA
70 KV:
5.0 mA
80 KV:
5.0 mA
90 KV:
5.0 mA
100 KV:
5.0 mA
110 KV:
5.0 mA
120KV:
5.0 mA
125 KV:
5.0 mA
Not Used
APOLLO EZ
PF SETUP
PF:
PF DEFAULT:
PPS DEFAULT:
PF DEFAULT MA:
ON
NONE
NONE
5=40mA
6=60mA
7=80mA
8=99mA
Note: Four options for the settings of the Pulsed Fluoro default mA are possible. It is
suggested to set the value 5 = 40mA as default parameter. The others settings are
possible on line by means the +/- mA keys. If, once set at 40 mA the default mA value
for the pulsed fluoro, is necessary to reduce the dose is possible to reduce the length
of the pulses by means the settings of the jumpers on the A2 board of the I.I. system
(make reference to the I.I. system service manual)
PF ABS SETUP
HPF SETUP
HLF SELECT:
CONSOLE
PF SELECT:
CONSOLE
APOLLO EZ
40
PF DEFAULT Ms:
PF SYNC FREQ:
ABS LEVEL 0:
ABS LEVEL 1:
ABS LEVEL 2:
ABS LEVEL 3:
SIGNAL GAIN:
ABS GAIN:
ABS DEADBAND:
ABS DELAY:
ABS START KV:
PF INTEGRATOR:
1PPS COMP:
3PPS COMP:
6/7.5PPS COMP:
12/15PPS COMP:
25/30PPS COMP:
Not Used
Not Used
Not Used
1 PPS:
3 PPS:
6/7.5 PPS:
12.5/15 PPS:
28/30 PPS:
Not Enable
2
50 HZ
4.0 V
1.10 V
1.20 V
1.90 V
3
5
40%
100 mS
75
OFF
0%
0%
0%
0%
0%
ON
ON
ON
ON
ON
(Rev. 0)
3.3.4
RECEPTOR
1
RECEPTOR
2
RECEPTOR
3
RECEPTOR
4
RECEPTOR
5
RECEPTOR
6
RECEPTOR
NAME
TUBE
NONE
NONE
NONE
TOMO
NO
NO
NO
NO
NO
NO
FLUORO
YES
NO
NO
NO
NO
NO
SERIAL
YES
NO
NO
NO
NO
NO
INTERFACE
OPTS
23
FUNCTIONAL
OPTS
FLUORO
HANG
30 SEC
30 SEC
30 SEC
30 SEC
30 SEC
30 SEC
RAD HANG
0 SEC
0 SEC
0 SEC
0 SEC
0 SEC
0 SEC
LAST IMAGE
HOLD
40 Ms
40 Ms
40 Ms
40 Ms
40 Ms
40 Ms
MEMORY
NO
NO
NO
NO
NO
NO
REM TOMO
BUT
2500 Ms
2500 Ms
2500 Ms
2500 Ms
2500 Ms
2500 Ms
SF/LF
SWITCH
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AEC BACKUP
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
AEC BACKUP
MAS
500
500
500
500
500
500
AEC BACKUP
MS
3200
3200
3200
3200
3200
3200
AEC
CHANNEL
AEC LOCK
EXPS
RECEPTOR
SYM
NOTE:
Receptor 3 has to be programmed only if Chest Stand with Potter Bucky
and AEC device is present.
(Rev. 0)
41
APOLLO EZ
3.3.5
FUNCTIONS
STANDBY
PREP
GEN RDY
RAD EXP
FLUORO EXP
ON
--------OFF
----OFF
----OFF
OFF
OFF
OFF
ON
OFF
ON
-----
--------ON
----------------OFF
OFF
----OFF
ON
OFF
ON
-----
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
***INPUTS***
REMOTE EXP
REMOTE PREP
REMOTE FL. EXP
CONSOLE EXP
CONSOLE PREP
TOMO EXP
REM. TOMO SEL
I/I SAFETY
COLL. ITLK
BUCKY CONTACTS
SPARE
THERMAL SW 1
THERMAL SW 2
DOOR ITLK
MULTI SPOT EXP
------------------------OFF
------------OFF
ON
OFF
OFF
OFF
OFF
ON
----OFF
OFF
--------OFF
OFF
----OFF
ON
OFF
ON
-----
-------------------------------------------------------------
***OUTPUTS***
BKY 1 SELECT
BKY 2 SELECT
BKY 3 SELECT
TOMO/BKY 4 SEL
TOMO/BKY START
ALE
COLL. BYPASS
ROOM LIGHT
SPARE
APOLLO EZ
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
42
(Rev. 0)
3.3.6
FUNCTIONS
STANDBY
PREP
GEN RDY
RAD EXP
FLUORO EXP
OFF
--------ON
----OFF
----OFF
OFF
OFF
OFF
ON
OFF
ON
-----
--------OFF
----------------OFF
OFF
----OFF
ON
OFF
OFF
-----
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
***INPUTS***
REMOTE EXP
REMOTE PREP
REMOTE FL. EXP
CONSOLE EXP
CONSOLE PREP
TOMO EXP
REM. TOMO SEL
I/I SAFETY
COLL. ITLK
BUCKY CONTACTS
SPARE
THERMAL SW 1
THERMAL SW 2
DOOR ITLK
MULTI SPOT EXP
------------------------OFF
------------OFF
ON
OFF
OFF
OFF
OFF
OFF
----OFF
ON
--------OFF
OFF
----OFF
ON
OFF
ON
-----
-------------------------------------------------------------
***OUTPUTS***
BKY 1 SELECT
BKY 2 SELECT
BKY 3 SELECT
TOMO/BKY 4 SEL
TOMO/BKY START
ALE
COLL. BYPASS
ROOM LIGHT
SPARE
(Rev. 0)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
43
APOLLO EZ
3.3.7
FUNCTIONS
STANDBY
PREP
GEN RDY
RAD EXP
FLUORO EXP
OFF
--------ON
----OFF
----OFF
OFF
ON
OFF
ON
OFF
ON
-----
--------OFF
----------------OFF
OFF
----OFF
ON
OFF
ON
-----
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
***INPUTS***
REMOTE EXP
REMOTE PREP
REMOTE FL. EXP
CONSOLE EXP
CONSOLE PREP
TOMO EXP
REM. TOMO SEL
I/I SAFETY
COLL. ITLK
BUCKY CONTACTS
SPARE
THERMAL SW 1
THERMAL SW 2
DOOR ITLK
MULTI SPOT EXP
------------------------OFF
------------OFF
ON
OFF
OFF
OFF
OFF
OFF
----OFF
ON
--------OFF
OFF
----OFF
ON
OFF
ON
-----
-------------------------------------------------------------
***OUTPUTS***
BKY 1 SELECT
BKY 2 SELECT
BKY 3 SELECT
TOMO/BKY 4 SEL
TOMO/BKY START
ALE
COLL. BYPASS
ROOM LIGHT
SPARE
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
NOTE:
The configuration of the Receptor 3 I/O has to be made only if the Chest
Stand with Potter Bucky is present.
APOLLO EZ
44
(Rev. 0)
Apollo EZ
Diva-D.
Chest Stand VD3 35x43 with motorised foot rest (See Note)
Receptor configuration
Receptor 1: Apollo EZ Spot Film Device Tube 1
Receptor 2: Digital Video Acquisition System Tube 1
Receptor 3: Chest Stand VD3 35x43 Tube 1 (See Note)
NOTE:
When the Generator is supplied with "Falling load" feature, the GalKey
U29 # 73594213 is installed on CPU board.
The Falling Load option it is not available on the receptors where the
"SERIAL" exposure is enable (paragraph 4.3.4 - Image Receptor
Programming Worksheet: "SERIAL=YES"); whenever the Falling Load has
to be activated on the Spot Film Device receptor, the SERIAL parameter
has to be set to "NO".
In case Falling Load feature and SERIAL exposure are required will be
necessary to create for each a dedicated receptor.
NOTE:
Reference to the Chest Stand VD3 35x43 with motorized foot rest is made
in order to allows the installer to record the necessary information for the
hardware interface among G 100 R/F-A and Potter Bucky.
(Rev. 0)
45
APOLLO EZ
4.1
Main
Power Supply
Generator
Terminals
G 100 R/F
ROOM INTERFACE BOARD
TB7.1 (0 Vac)
* INSTALLATION KIT
230Vac AUXILIARY CONTACTOR
V.S.M. cod.4291515200
G 100 R/F
ROOM INTERFACE BOARD
TB10.1 (220 Vac)
R S T
APOLLO EZ
Terminals R-S-T
R S
CHEST STAND
Terminal X1 (**)
(*) If this remote controlled switch is not available use a remote controlled
switch with the following characteristics:
Coil:
220-230 Vac 50 Hz
230-240 Vac 60 Hz
APOLLO EZ
46
(Rev. 0)
4.2
4.2.1
APOLLO EZ
Description
Terminal
Description
X27.15
TB6.9
Remote Exposure
(Room Interface Board)
X27.3
TB6.7
Preparation radiography
(Room Interface Board)
Common
0Vdc
X0.20
J6.2
0V
(Table Digital Interface board)
Common 0VS
X27.23
J6.23
0V analog
(Table Digital Interface board)
Manual kV
ref.
X27.11
J6.7
Fluoro kV
manual/auto
selection
X27.20
J6.1
Man/Auto fluoro
(Table Digital Interface board)
Tomo
speed 1
X27.4
Tomo
speed 2
X27.1
J6.3
Tomo speed 1
(Table Digital Interface board)
Tomo
speed 3
X27.14
Tomo
speed 4
X27.17
J6.4
Tomo speed 2
(Table Digital Interface board)
Tomo 7
X27.5
J7.1
Tomo 7
(Table Digital Interface board)
Tomo 20
X27.18
J7.3
Tomo 20
(Table Digital Interface board)
Tomo 30
X27.6
J7.4
Tomo 30
(Table Digital Interface board)
(Rev. 0)
Terminal
G 100 R/F-A
Wire n
47
APOLLO EZ
APOLLO EZ
Description
Terminal
Tomo 45
G 100 R/F-A
Wire n
Terminal
Description
X27.19
J7.5
Tomo 45
(Table Digital Interface board)
Alarm
X-ray ON
X27.7
(see Note)
J7.6
X-ray OFF
(Table Digital Interface board)
SFD selection
X0.15
TB2.12
Bucky 1 select
(Room Interface Board)
DSI selection
X0.14
TB2.1
Bucky 2 select
(Room Interface Board)
X-ray ON
from
generator
X0.13
J6.21
X-Ray on
(Table Digital Interface board)
Generator
ready
X0.12
J6.22
Generator Ready
(Table Digital Interface board)
Safety switch
X0.9
J17.1
Safety switch
(Generator Interface PWB)
Safety switch
X0.11
J17.2
Safety switch
(Generator Interface PWB)
NOTE:
During the auto calibration of the X-ray tube it is required to make the
jumper between J7.6 and J6.2 (force terminal J7.6 at 0Vdc).
It is important to remove the jumper at the end of the X-ray tube
auto calibration.
APOLLO EZ
48
(Rev. 0)
4.2.2
APOLLO EZ
Description
Terminal
DIVA-D
Wire n
POD pcb
Description
X28.18
20
Fluoroscopy request
X28.6
15
Generator ready
X28.19
21
Exposure request
Common
0Vdc
X28.22
11
0 V digital common
Common
X28.3
12
0 V digital common
X28.4
18
X28.16
19
X0.13
14
X-ray ON
1
3
13
D.S.I.
X-ray ON
from
generator
(Rev. 0)
49
APOLLO EZ
4.2.3
G 100 R/F-A
DIVA-D
POD
pcb
Description
J7.22
Preparation radiography
J6.24
Preparation command
Start fluoroscopy
J7.23
Fluoroscopy command
X-ray request
J7.24
X-ray command
Description
TDI
Pulses fluoroscopy
Wire n
4.2.4
G 100 R/F-A
DIVA-D
Description
Plug
Serial connection
(Generator CPU board)
J15
APOLLO EZ
Wire n
50
Plug
Description
RS232
Serial connection
(Rack)
(Rev. 0)
4.2.5
APOLLO EZ
Description
Terminal
Common
Wire n
Pcb A1
Description
4 fields
3 fields
X28.1
X4.4
X4.4
Common
Medium field
X28.2
X4.2
X4.1
Medium zoom
Minimum field
X28.14
X4.3
X4.2
Maximum
zoom
Maximum field
X28.15
X4.1
N.C.
Minimum
zoom
Power supply
X0.2
Power supply
Power supply
S3
X0.1
Power supply
X0.3
Ground
Ground
(Rev. 0)
51
APOLLO EZ
4.2.6
DIVA-D
Description
POD Pcb
Analog intensifier
field selection
0 V analog
Wire n
Pcb A1
Description
25
X5.1
29
X5.2
0 V analog
Monitor interface
4.2.7
Pcb A2
Monitor L.I.H.
visualization
0 Vs common
APOLLO EZ
Plug
Description
X4.2
LI
Monitor L.I.H.
visualization
X4.10
0V
0 Vs common
52
(Rev. 0)
4.2.8
G100 R/F-A
AEC board
(solid state chamber)
type 737992
AEC device 1
connecting cable
Description Terminal
Wire
Description
Anode (L)
J11.1
Pink
Anode Left
Cath (L)
J11.2
Grey
Cathode Left
Anode (M)
J11.3
White
Anode Middle
Cath (M)
J11.4
Brown
Cathode Middle
Anode (R)
J11.5
Green
Anode Right
Cath (R)
J11.6
Yellow
Cathode Right
Ground
J11.7
Shield
Ground
(Rev. 0)
53
APOLLO EZ
4.2.9
G 100 R/F-A
X-ray tube
Description
Terminal
Main
Terminal
Description
Tube 1
Principal
Shift
Tube 1
Auxiliary
Common
Tube 1
Common
Ground
Tube 1
Ground
Thermal switch
Tube 1
Thermal switch
Thermal switch
Tube 1
Thermal switch
APOLLO EZ
Wire n
54
(Rev. 0)
4.2.10
Terminal
X-ray request
G 100 R/F-A
Wire n
Terminal
Description
X1.B1
TB1.11
Bucky 3 select
X-ray request
X1.B2
TB1.12
Bucky 3 select
Potter reply
X1.X
TB2.5
Bucky contacts
Potter reply
X1.X
TB2.4
Bucky contacts
WARNING:
The voltage selected on TB1.11 and TB1.12 is 24 Vdc. Refer to the Chest
Stand VD3 35x43 Technical and User's Manual for the Bucky start
voltage setting.
(Rev. 0)
55
APOLLO EZ
4.2.11
G100 R/F-A
AEC board
(solid state chamber)
type 737992
AEC device 2
connecting cable
Description Terminal
Wire
Description
Anode (L)
J12.1
Pink
Anode Left
Cath (L)
J12.2
Grey
Cathode Left
Anode (M)
J12.3
White
Anode Middle
Cath (M)
J12.4
Brown
Cathode Middle
Anode (R)
J12.5
Green
Anode Right
Cath (R)
J12.6
Yellow
Cathode Right
Ground
J12.7
Shield
Ground
APOLLO EZ
56
(Rev. 0)
4.2.12
JW2:
JW3:
JW4:
TB8.1 TB11.5
TB4.8 TB4.9:
JW1:
JW2:
JW3:
JW4:
JW5:
JW6:
JW7:
JW8:
JW9:
JW10:
JW11:
JW12:
12
12/
12/
Open
Close
12/
12/
12/
12/
12/
23
Open
34
34
3
3
3
3
3
4
4
4
4
4
JW13:
JW14:
JW15:
JW19:
JW20:
JW21:
JW22:
JW24:
JW25:
JW26:
JW27:
JW28:
Open
1 2 / 3 4
12/34
23
Close
12
23
Close
Close
Close
Close
Open
NOTE:
The configuration of the Jumpers not listed in the previous tables is not
relevant for this system integration.
(Rev. 0)
57
APOLLO EZ
SW1-1:
SW1-2:
SW1-3:
SW1-4:
OFF
OFF
ON
OFF
SW1-5:
SW1-6:
SW1-7:
SW1-8:
ON
OFF
OFF
OFF
Generator
Accessory
Description
Terminal
Wire n
Description
TB4.4
Door contact
TB4.5
Door contact
Room light 0V
(Room Interface board)
TB7
Generator ON lamp
(white lamp)
(*)
Generator ON lamp
(white lamp)
TB4.11
X-ray ON lamp
(red lamp)
TB4.12
X-ray ON lamp
(red lamp)
(*) TB10 for 220V ac / TB9 for 110V ac / TB8 for 24V dc
NOTE:
Remove jumper JW13 on Room Inteface Board.
APOLLO EZ
58
(Rev. 0)
4.3
4.3.1
Tube selection
Prior to beginning tube calibration, the tube used in the installation must
be properly selected, and generator limits should be programmed.
4.3.1.1
(Rev. 0)
59
APOLLO EZ
4.3.1.2
4.3.1.3
APOLLO EZ
60
(Rev. 0)
4.3.2
AEC set-up
The installation of the AEC devices and their calibration are covered in
the G 100 R/F-A Service Manual, chapter 3E - Automatic exposure
control (AEC) calibration.
4.3.3
Fluoro set-up
NOTE:
The Fluoro set-up data must be set in according with the X-ray tube
technical specification.
The following tables meets the Fluoro set-up request in according with
most of the X-ray tube supplied by Villa Sistemi Medicali; during the
installation could be necessary to optimize the set-up.
The installation of the ABS device and his calibration are covered in the
G 100 R/F-A Service Manual, chapter 3 - Automatic brightness
stabilisation (ABS) calibration.
The next table show the standard parameters usually set.
FLUORO SET-UP
FL TIMER:
5 Min
MIN FLUORO KV:
40
MAX FLUORO KV:
120
II MODES:
0
FL ABS:
ON
FL ABS DEFAULT: NONE
FL/RAD KV DEF: NONE
FL/RAD KV CURVES
SID COMP
FL SETUP
Not Used
Not Used
FL ABS SETUP
(Rev. 0)
61
ABS LEVEL 0:
ABS LEVEL 1:
ABS LEVEL 2:
ABS LEVEL 3:
SIGNAL GAIN
ABS GAIN
ABS DEADBAND
ABD DELAY
ABS START KV
5.00 V
5.00 V
5.00 V
5.00 V
10
10
3%
150 mS
75
APOLLO EZ
FL ABS CURVE
FL DOSE LIMIT
HLF SETUP
APOLLO EZ
FL II COMP
Not Used
62
FL ABS CURVE 1:
ON
40KV:
0.5 mA
50 KV :
1.0 mA
60 KV :
2.0 mA
70 KV :
3.0 mA
80 KV :
4.0 mA
90 KV :
5.0 mA
100 KV :
6.0 mA
110 KV :
7.0 mA
120 KV:
8.0 mA
8.0mA
125 KV :
* FL MAN DL *
40KV:
0.5 mA
50 KV:
1.0 mA
60 KV:
1.6 mA
70 KV:
2.1 mA
80 KV:
2.7 mA
90 KV:
3.2 mA
100 KV:
3.8 mA
110 KV:
4.4 mA
120KV:
5.0 mA
5.0mA
125 KV:
* FL ABS DL *
40KV:
5.0 mA
50 KV:
5.0 mA
60 KV:
5.0 mA
70 KV:
5.0 mA
80 KV:
5.0 mA
90 KV:
5.0 mA
100 KV:
5.0 mA
110 KV:
5.0 mA
120KV:
5.0 mA
125 KV:
5.0 mA
Not Used
(Rev. 0)
PF SETUP
PF:
PF DEFAULT:
PPS DEFAULT:
PF DEFAULT MA:
ON
NONE
NONE
5=40mA
6=60mA
7=80mA
8=99mA
Note: Four options for the settings of the Pulsed Fluoro default mA are possible. It is
suggested to set the value 5 = 40mA as default parameter. The others settings are
possible on line by means the +/- mA keys. If, once set at 40 mA the default mA value
for the pulsed fluoro, is necessary to reduce the dose is possible to reduce the length
of the pulses by means the settings of the jumpers on the A2 board of the I.I. system
(make reference to the I.I. system service manual)
PF DEFAULT Ms:
PF ABS SETUP
HPF SETUP
HLF SELECT:
CONSOLE
PF SELECT:
CONSOLE
(Rev. 0)
63
PF SYNC FREQ:
ABS LEVEL 0:
ABS LEVEL 1:
ABS LEVEL 2:
ABS LEVEL 3:
SIGNAL GAIN:
ABS GAIN:
ABS DEADBAND:
ABS DELAY:
ABS START KV:
PF INTEGRATOR:
1PPS COMP:
3PPS COMP:
6/7.5PPS COMP:
12/15PPS COMP:
25/30PPS COMP:
Not Used
Not Used
Not Used
1 PPS:
3 PPS:
6/7.5 PPS:
12.5/15 PPS:
28/30 PPS:
Not Enable
Not
Used
50 HZ
5.0 V
5.0 V
5.0 V
5.0 V
10
8
10%
150 mS
75
OFF
0%
0%
0%
0%
0%
ON
ON
ON
ON
ON
APOLLO EZ
4.3.4
RECEPTOR
1
RECEPTOR
2
RECEPTOR
3
RECEPTOR
4
RECEPTOR
5
RECEPTOR
6
RECEPTOR
NAME
TUBE
NONE
NONE
NONE
TOMO
NO
NO
NO
NO
NO
NO
FLUORO
YES
YES
NO
NO
NO
NO
SERIAL
YES
YES
NO
NO
NO
NO
INTERFACE
OPTS
20
21
FUNCTIONAL
OPTS
FLUORO
HANG
30 SEC
30 SEC
30 SEC
30 SEC
30 SEC
30 SEC
RAD HANG
0 SEC
0 SEC
0 SEC
0 SEC
0 SEC
0 SEC
LAST IMAGE
HOLD
40 Ms
40 Ms
40 Ms
40 Ms
40 Ms
40 Ms
MEMORY
NO
NO
NO
NO
NO
NO
REM TOMO
BUT
2500 Ms
2500 Ms
2500 Ms
2500 Ms
2500 Ms
2500 Ms
SF/LF
SWITCH
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AEC BACKUP
FIXED
FIXED
FIXED
FIXED
FIXED
FIXED
AEC BACKUP
MAS
500
500
500
500
500
500
AEC BACKUP
MS
3200
3200
3200
3200
3200
3200
AEC
CHANNEL
AEC LOCK
EXPS
RECEPTOR
SYM
NOTE:
Receptor 3 has to be programmed only if Chest Stand with Potter Bucky
and AEC device is present.
APOLLO EZ
64
(Rev. 0)
4.3.5
FUNCTIONS
STANDBY
PREP
GEN RDY
RAD EXP
FLUORO EXP
ON
--------OFF
----OFF
----OFF
OFF
OFF
OFF
ON
OFF
ON
-----
--------ON
----------------OFF
OFF
----OFF
ON
OFF
ON
-----
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
***INPUTS***
REMOTE EXP
REMOTE PREP
REMOTE FL. EXP
CONSOLE EXP
CONSOLE PREP
TOMO EXP
REM. TOMO SEL
I/I SAFETY
COLL. ITLK
BUCKY CONTACTS
SPARE
THERMAL SW 1
THERMAL SW 2
DOOR ITLK
MULTI SPOT EXP
------------------------OFF
------------OFF
ON
OFF
OFF
OFF
OFF
ON
----OFF
OFF
--------OFF
OFF
----OFF
ON
OFF
ON
-----
-------------------------------------------------------------
***OUTPUTS***
BKY 1 SELECT
BKY 2 SELECT
BKY 3 SELECT
TOMO/BKY 4 SEL
TOMO/BKY START
ALE
COLL. BYPASS
ROOM LIGHT
SPARE
(Rev. 0)
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
65
APOLLO EZ
4.3.6
FUNCTIONS
STANDBY
PREP
GEN RDY
RAD EXP
FLUORO EXP
ON
--------OFF
----OFF
----OFF
OFF
OFF
OFF
ON
OFF
ON
-----
--------ON
----------------OFF
OFF
----OFF
ON
OFF
ON
-----
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
***INPUTS***
REMOTE EXP
REMOTE PREP
REMOTE FL. EXP
CONSOLE EXP
CONSOLE PREP
TOMO EXP
REM. TOMO SEL
I/I SAFETY
COLL. ITLK
BUCKY CONTACTS
SPARE
THERMAL SW 1
THERMAL SW 2
DOOR ITLK
MULTI SPOT EXP
------------------------OFF
------------OFF
ON
OFF
OFF
OFF
OFF
ON
----OFF
OFF
--------OFF
OFF
----OFF
ON
OFF
ON
-----
-------------------------------------------------------------
***OUTPUTS***
BKY 1 SELECT
BKY 2 SELECT
BKY 3 SELECT
TOMO/BKY 4 SEL
TOMO/BKY START
ALE
COLL. BYPASS
ROOM LIGHT
SPARE
APOLLO EZ
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
66
(Rev. 0)
4.3.7
FUNCTIONS
STANDBY
PREP
GEN RDY
RAD EXP
FLUORO EXP
OFF
--------ON
----OFF
----OFF
OFF
ON
OFF
ON
OFF
ON
-----
--------OFF
----------------OFF
OFF
----OFF
ON
OFF
ON
-----
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
***INPUTS***
REMOTE EXP
REMOTE PREP
REMOTE FL. EXP
CONSOLE EXP
CONSOLE PREP
TOMO EXP
REM. TOMO SEL
I/I SAFETY
COLL. ITLK
BUCKY CONTACTS
SPARE
THERMAL SW 1
THERMAL SW 2
DOOR ITLK
MULTI SPOT EXP
------------------------OFF
------------OFF
ON
OFF
OFF
OFF
OFF
OFF
----OFF
ON
--------OFF
OFF
----OFF
ON
OFF
ON
-----
-------------------------------------------------------------
***OUTPUTS***
BKY 1 SELECT
BKY 2 SELECT
BKY 3 SELECT
TOMO/BKY 4 SEL
TOMO/BKY START
ALE
COLL. BYPASS
ROOM LIGHT
SPARE
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
NOTE:
The configuration of the Receptor 3 I/O has to be made only if the Chest
Stand with Potter Bucky is present.
(Rev. 0)
67
APOLLO EZ
APOLLO EZ
68
(Rev. 0)
Cod. 6998312603_Rev.0