Beruflich Dokumente
Kultur Dokumente
SIMATIC S7
Siemens AG 2007. All rights reserved.
Date:
File:
11.06.2007
PRO1_02E.1
Contents
Page
Page 1
2
3
4
5
6
9
10
11
ST-PRO1
Training Units and Addressing
SIMATIC S7
Date:
File:
11.06.2007
PRO1_02E.2
Page 2
ST-PRO1
Training Units and Addressing
Module
-->
PS
CPU
DI 32
DO 32
DI8/DO8
AI 2
Slot No.
-->
I/O Address
-->
304
SIMATIC S7
Date:
File:
Configuration
Addresses
11.06.2007
PRO1_02E.3
For the training unit with the CPU 315-2DP and for the S7-400 training unit, you
can set the starting addresses of the modules by parameter assignment
(freely).
Page 3
ST-PRO1
Training Units and Addressing
The Simulator
Potentiometers for
setting the
analog values
PIW_AI1 (PIW 304)
DO
.0
..........
..........
.0
.1
..........
..........
.1
.2
..........
..........
.2
.3
..........
..........
.3
.4
..........
..........
.4
.5
..........
..........
.5
.6
..........
..........
.6
.7
..........
..........
.7
.0
..........
..........
.1
..........
..........
.2
..........
..........
.3
..........
..........
.4
..........
..........
.5
..........
..........
.6
..........
..........
.7
..........
..........
-15V...+15V
AI1
.0
.1
AI1
.2
AI2
.3
.4
.5
0 8 1 5
AI1
AI2
AO1
AO2
.6
.7
SIMATIC S7
Date:
File:
Design
Addressing
11.06.2007
PRO1_02E.4
Two cables connect the simulator to the S7-300 or S7-400 training unit. The
simulator is divided into the following three sections:
Analog section with a voltmeter for displaying the values at analog channels
0 and 1 or the analog outputs 0 and 1. You use the selector switch to choose
the voltage value you want to monitor. There are two separate
potentiometers for setting the values for the analog inputs.
You use the following addresses to address the inputs and outputs in your user
program :
Sensor / Actuator
(DI32, DO32)
Switch / Mom.Cont. IW 0
LEDs
QW 4
Thumb. buttons
IW 2
Digital display
QW 6
Analog channels
PIW 304/306
Page 4
ST-PRO1
Training Units and Addressing
"BAY1"
(I 8.5)
"BAY2"
(I 8.6)
"BAY3"
(I 8.7)
"Horn"
(Q 8.7)
"LB"
(I 8.0)
"T_Bay1"
"T_Bay2"
"T_Bay3"
"T_Bay-LB"
(I 8.1)
(I 8.2)
(I 8.3)
(I 8.4)
"L_Bay1"
"L_Bay2"
"L_Bay3"
"L_Bay-LB"
(Q 8.1)
(Q 8.3)
(Q 8.4)
(Q 8.2)
SIMATIC S7
Date:
File:
Design
11.06.2007
PRO1_02E.5
The slide above shows the conveyor model with its sensors and actuators.
Page 5
ST-PRO1
Training Units and Addressing
Page 6
ST-PRO1
Training Units and Addressing
Page 7
ST-PRO1
Training Units and Addressing
Page 8
ST-PRO1
Training Units and Addressing
SIMATIC S7
Date:
File:
Note
11.06.2007
PRO1_02E.9
The following pages contain either further information or are for reference to
complete a topic.
Page 9
ST-PRO1
Training Units and Addressing
SIMATIC S7
Date:
File:
Contents of the
Training Area
11.06.2007
PRO1_02E.10
Page 10
ST-PRO1
Training Units and Addressing
PS
CPU
SIMATIC S7
DI
32
DI
32
10
11
12
13
14
15
16
17
18
DO DO AI
32 32 8
Date:
File:
11.06.2007
PRO1_02E.11
Design
You can see the design of the S7-400 training unit in the slide above.
Configuration
Addressing
You have the default addresses, as shown in the slide above, as long as no
configuration or parameter settings have been made.
Page 11
ST-PRO1
Training Units and Addressing