Beruflich Dokumente
Kultur Dokumente
3. Which of the following would be the correct way(s) of using a torque wrench?
A. Application of jerk pulls while tightening
B. Using an extension
C. Tightening beyond the characteristic clicking sound
D. None of the above
4. Chromium is a nobler metal when compared to that of steel. In some
marine applications Chromium is electroplated to the steel surfaces.
Why?
A. Chromium is a more noble metal so it will not get corroded and
thus steel surfaces will remain protected
B. Chromium plating provides corrosion protection as well as high
glossiness and high hardness for better wear resistance and reduced
friction to the steel surfaces
C. Chromium plating is required for providing high glossiness and high hardness for better wear
resistance and reduced friction to the steel surfaces and not for corrosion protection
D. Chromium reacts with steel to form an alloy during electroplating which is corrosion resistant
6. Centrifugal pumps cannot handle air and require priming. But you are
aware that centrifugal which on the same principal can handle air
very well. Which two properties of air are responsible because of
which the centrifugal pumps cannot handle air:A. Fluidity only
B. Density only
C. Both fluidity and density
D. Compressibility
7. Pump driven clutch type attached vacuum pumps are commonly used for
priming ballast pumps and emergency fire pumps. What is the
factor which clutches the vacuum pump clutch to the pump clutch
during start of the pump?
A. Low suction pressure acting against the spring loaded clutching
piston
9. Increasing the rotational speed of a cargo pump the pump flow rate will:
A. Increase in direct proportion to the increase in speed
B. Decrease in direct proportion to the increase in speed
C. Flow rate doesnt???t depend upon speed
D. Flow
10. It has been reported that Engine room bilge pump was unable to take
suction from Fwd. (P) bilge well while it taking suction efficiently
from Fwd.(S) & aft bilge wells. What could be the most probable
cause?
A. There is leakage in the bilge suction pipeline somewhere between
the bilge wells and bilge pump
B. The Fwd. (P) bilge well suction valve might be leaking
C. The Fwd. (P) bilge well suction filter cover gasket might be leaking
D. The pump needs to be overhauled
11. Which of the following is a correct point for sampling of system lube oil for on board or
shore analysis?
A. Standpipes
B. Purifier outlets
C. Inlet or outlet of L. O. coolers
D. Tank drains
12. Which type of valve is not rotating type....
a) gate v/v
b)butterfly v/v
c)ball v/v
d)plug v/v
13. Emergency steering testing
1. Weekly
2. Monthly
3. At least 3 months
4. Before arrival n departure
14. Rudder is locked at an angle & can be moved by manual change-------1. Follow up
2. Non follow up
14. Rudder is locked at an angle & can be moved by manual change-------1. Follow up
2. Non follow up
16. When securing a centrifugal distillate pump, which of the listed steps
should be carried out FIRST?
1.
2.
3.
4.
A. Gate valve
B. Globe Check Valve
C. Swing Check Valve
D. Angle check valve
18. After your overhaul a centrifugal pump is not rotating what may be the
possible cause:
a. Uneven tightening of casing bolts
b.Gasket thickness very thin
c.More wear ring clearance
d.Only a
e. a and b
f. a and c
19. Pump driven clutch type attached vacuum pumps are commonly used
for priming ballast pumps and emergency fire pump. What is the
factor which de-clutches the vacuum pump from the pump clutch?
A. Low suction pressure acting against the spring loaded declutching
piston
B. High suction pressure acting against the spring loaded declutching
piston
C. Low discharge pressure acting against the spring loaded
declutching piston
D. High discharge pressure acting against the spring loaded
declutching piston
20. The main disadvantages of a reciprocating pump over a Gear pump is
that:
A. A gear pump is self priming while a reciprocating pump is not
B. Discharge of a gear pump is not affected by the direction of rotation while that of reciprocating
pump is reversed
C. The discharge of reciprocating pump is pulsating and discharge rate is lesser
D. Reciprocating pumps are only available in high capacities and for smaller capacities only gear
pumps can be used
22. After cleaning the sea chest filter you have placed the filter in the body
and tightened the cover. Which one of the following is the best
alternative?
A. You can open the filter inlet and outlet valves & directly start using
the filter
B. If you do not want to use the sea chest in question, you need not worry and you can open the
valves when required
C. Sea Water inlet valve should be crack opened, the filter body should be purged, any leakages
and thereafter filter can be kept isolated or used as required
D. You will close the other side sea chest valves first and then open this side sea chest filter inlet
and outlet valves
23. In which of the following types of refractory failure, softening of the
refractory bricks takes place due to presence of sodium/vanadium
in fuel?
A. Spalling
B. Cracking
C. Shrinkage cracking
D. Slagging
24. centrifugal pump will typically give you a low flow rate at a lower
pressure, where a piston pump will give you more pressure and
higher flow rate. Is the statement correct?
A.TRUE
B.FALSE
C. First Sentence is right. Second one is wrong
D. I dont know
25. You are pumping out sludge to a shore facility using your sludge pump. You find that the
discharge rate of pump is very slow and suction filter is getting clogged frequently. What is the best
alternative to counteract the problem?
A. Remove the pump suction filter and pump out the tank
B. Increase the tank temperature, keep an eye on the pump suction pressure and clean the filter as
soon as it drops
C. As soon as the as the shore facility tells you that they are not receiving any sludge, you stop the
pump and clean the filter
D. Fabricate a bigger mesh size suction filter and use in place of normal filter so that frequency of
filter blockage is reduced and you can get a better discharge rate
26. Pump Start but Motor get overloaded or Trip on overload.
A. Alignment is wrong
B. Gland packing too tight
C. Worn out / Damaged ball bearing
D. Cavitations exists
E. All of the above
27. A ball valve is found leaking in service and needs to be overhauled.
What type of repairs can be carried out?
a. The ball and seat can be lapped together
b. The ball can be machined while the seat can be replaced
c. Normally both the non-metallic seats get worn out and have to be
replaced
d. Normally ball gets damaged and has to be replaced
28. The difference between the discharges of a centrifugal pump n
reciprocating pump
the discharge of centrifugal pump is ----------while that if
reciprocating is --------A) Turbulent, Laminar
B) Intermittent, continuous
C) Continuous, pulsating
D) Pulsating, continuous
29. Purifier is not rotating with desired rpm, reason?
1. Frequency low
2. Bus bar voltage low
3. Friction pads worn out
41. As the amount of moisture in the air increases, the difference between the dry bulb and wet bulb
temperatures will..
Decrease
Section 2:
1. ESD III refractory
a. Fire
b. Insulation
c. Membrane webs
2. Change in volume in closed cooling system is achieved by
a. Fresh water expansion tank
3. Turbocharger most preferred
a. Cheap
b. Boost air pressure
c. Increase efficiency
d. Reduce nox
4. Microbial degradation
a. Corrosive
b. Stable emission
c. Caustic fire
d. All the above
5. Function of a de-superheater is to.
A. Protect superheater from overheat
B. Control superheater steam outlet temperature
C. Increase the efficiency of the boiler
D. Reduce steam temperature for auxiliary uses after steam
superheater
6. Why should combustion blowers left running for while after firing a boiler?
a. To cool the furnace internal
b. To remove the gases
c. To cool tubes
d. None
7. Dezincification of brass can be prevented by introduction of additives like
a. Nickel
b. Cobalt
c. arsenic
d. Tungsten
8. Principle of fire fighting onboard is
a. Watering of fire
b. Starving of fire
c. Cooling
d. Smothering of fire
9. Which of the following used in boiler treatment is an oxygen scavenging
a. Polymer
b. Neutralizing amine
c. Sodium sulphate
d. Filming amine
10. Salinity of distilled water produced depends upon _
a. Amount of feed set
b. Amount of salt water
c. Temp of sea water inlet
11. High pressure differential of a M/E LO filter only can be reduced by
a. Back flushing filter
b. Changing over to standby filter
c. Change M/E
12. The LO temperature (question not complete)
a. Start increases immediately
b. Start decreases immediately
c. Will be maintained at the set point
d. Cant maintain at the set point and decrease slowly
13. Fixed vane type emergency fire pump priming vacuum pump. After one week fire pump not
taking suction. The vacuum pump is engaging, but not developing vacuum in the suction side.
What will be the cause?
a. Suction filter of the pump clogged
b. Suction filter cover gasket leaks
c. Vacuum pump not overhauled properly
d. Sealing water tank is empty
14. Single screw pump used as sludge pump the correct technical name.
a. Snake pump
b. Screw pump
c. Progressive cavity pump
d. Gear pump
15. Excessive lubricator in compressor leads to
a. Decompression
b. Detonation
c. Sticking in valves and
d. Carry over and deposit of all particles in pipe line and reservoir
16. Corrosion occurs in cooling fresh water system of marine diesel engine
a. Stress corrosion
b. Hot corrosion
c. Bimetallic corrosion
d. Selective phase corrosion
17. Purpose of evaporator in domestic refrigeration system
a. To transmit latent heat of evaporation
b. To absorb latent heat of fussion
c. To absorb latent heat of evaporation
d. To transmit latent heat of fussion
18. Sudden closing and opening of valve in sea water pipeline leads to
a. Cavitations
b. Water hammering
c. Steam hammering
d. There is no problem
19. Centrifugal pump change over for pumping liquid of high specific gravity the discharge at the
rated capacity will be
a. Increase
b. Decrease
c. Same
d. Convert 50%
20. Centrifugal pump change over for pumping liquid of high specific gravity what will change?
a. Discharge pressure
b. Discharge head
c. Power consumption
d. Pump speed
21. Weldability steel depends on carbon equivalent
a. CE<= 0.35
b. CE between O.36 AND 0.4
c. CE between o.41 and o.45
d. CE between o.46 and o.5
22. Sea water outlet temperature of LO cooler decreased while main engine load and sea water
inlet temperature not changed this indicates
a. Cooler efficiency has increased
b. Cooler efficiency has decreased
c. Sea water outlet temp nothing to do with efficiency
d. The flow of sea water reduced
23. Ballast pump suction filters during ballast in port purpose of getting blocked frequently you
should
a. Remove the suction filter
b. Clean frequently as required and also open and check the sea chest filter
c. Stop using the pump and keep fill in gravity
d. Stop the ballast operation
24. When steel components electroplated with chromium are used in corrosive environment
a. Chrome plating prevents corrosion
b. Protection to the steel will be preferentially corroded
c. Zinc plating is used on top of chrome plating for corrosion protection
d. Thickness of chrome plating to increase
25. Steel is an alloy of iron carbon and alloying components what is the carbon content?
a. Less than 1 %
b. Less than 2%
c. Greater than 2%
d. Any % of carbon
26. Tube in air compressors , self compensating for expansion (if multi choice include coil tube
also)
a. Straight line tube
b. U tube
c. Coil tube
d. Floating tube kismet kaun sa hota h?
27. ___________ boiler feed pumps is used in modern ships
a. Reciprocating pump
b. Heleshaw pump
c. Multistage centrifugal pump
d. Single stage centrifugal pump
28. The actuator of ballast valve in duct keel in port to carry deballast open best practice
a. Interchange from another valve.
b. Manually operated
c. Leave the tank full and ask for shore assistance.
d. Portable pump through manhole.
29. To reduce sulphur corrosion of main engine components
a. Run at normal load
b. Atomizing pressure of fuel
c. Rotor in exhaust valve
d. Fuel feed rate in purifier and purifier in series
30. Crude oil or crude oil+ballast water of same specific gravity ________ current in pump with
same discharge pressure
a. More
b. Less
c. Same
d. Does not depend
31. Refrigerant compressor will run continuously
a. Too heavy cooling load
d. all
40. Refer cooling tubes act as self-cooling & expansion by
a) Straight tube
b) U tube
c) Spring tube
41. Which of the following is an important requirement for proper functioning of sacrificial
anode system?
A. Good Insulation between anodes and ship???s hull
B. Good electrical continuity between anodes and ship???s hull
C. Providing protection of anodes from being painted over during hull painting
D. Presence of an insulating material between anode and the cathode
42. Purifier leaking bowl opened, cleaned n seal ring changed and put back but still leaking what
might b wrong?
A. high temp
B. high density
C. disc size not proper
D. rpm low
43. Increased fuel injection temperature and maintaining recommended viscosity of a new bunkers
fuel oil.
A. viscotherm running fine
B. Problem in viscotherm
C. best quality bunkers
D. None
44. Overall length of pairs of rams is reduced in which of the following tiller designs of a steering
gear arrangement?
A. Forked tiller design
B. Round arm tiller design
C. Conventional tiller design
D. None of the above
45. In refrigeration circuit, the data logger will record what? (Multi choice)
1. Room temperature
2. Recharge temperature
3. Liquid line temperature
4. Solenoid valve operation
46. Engaging the turning gear and turning the engine until working temperatures are reduced
A. Blank starting air to the affected cylinder
B. Shut cylinder oil to the affected cylinder
C. Shut all cylinder liner ports of affected cylinder
D. Open relief valve of affected cylinder
47. You as a fourth engineer have taken over watch from third engineer. He said OWS is running in 0
ppm. But after taking over watch you observed that fresh water flushing valve is crack open. After
closing it, suddenly the oil content has exceeded 15ppm. What will you do?
a. shut the OWS & inform CEO.
b. shut the OWS but no need to inform anyone.
c. Don't touch the appratus & inform CEO.
d. Just check that there is no visible colour/oil traces in sea water so don't have to inform anyone.
48. With ref to centrifugal p/p characteristics curves what will be the effect when p/p is started
A. with suction closed
B. with discharge shut
49. Non destructive test is
A. impact test
B. Ultraviolet test
C. to check alkalinity
51. The coating on an electrode used for electric arc welding
A. creates a gas shield to prevent oxidation of the weld material
B. helps the weld formation by shaping the metal transfer
C. provides an electrical insulation for the user
D. All of the above
52. Which vessel is mostly used for carrying NH3/ LPG
A. Semi pressurized
B. Fully pressurized
C. Fully refrigerated
D. All the above
53. Pump, when coupled to constant speed motor , the discharge quantity will not change with
following pumps
A. heleshaw
B. steering gear swash plate type
C. Gear pump
D. None
54. Electrical fire extinguished by
A. Co2
B. DCP
C. FOAM
55. over speed trip of generator
a. governor has to be check
b. fuel oil system
56. Purpose of preferential trip to prevent
A. blackout
B. To avoid overload
C. to start heavy machinery
D. all
57. Flooding in E/R,
A. pump out through OWS to overboard
D. all
65. Increasing the rotational speed of a cargo pump the pump flow rate will:
A. Increase in direct proportion to the increase in speed
B. Decrease in direct proportion to the increase in speed
C. Flow rate doesn???t depend upon speed
D. Flow
66. Boiler water level control, controlling swell and shrink of boiler with
A. feed water level
B. steam drum
C. water drum
D. none of the above
Section 3:
1. The pressure produced within the oil wedge of a rotating journal is ____.
the same as the pressure in the lubricating system
less than the pressure in the lubricating system
greater than the pressure in the lubricating system
highest at the oil groove location
2. Which of the main shaft segments listed below, that are connected with the main engine, are
coupled to the tail shaft flange?
Thrust shaft
Stern-tube shaft
Intermediate shaft
Crank shaft
3. Piping cross-sections over 30 cm in diameter are sized by the __________.
inside diameter
wall thickness
outside diameter
threaded diameter
4. The ambient heat in an engine room which is identified by only a change in temperature is
known as
sensible heat
latent heat
total heat
residual heat
5. The usual number of single-acting pistons used in a variable stroke axial-piston pump used for
steering gears is _____________.
3 or 5
5 or 7
7 or 9
9 or 11
6. Heavy soot accumulations in an auxiliary boiler could be caused by _____
water in the fuel oil
excessive cycling
high fuel oil pressure
improper burner maintenance
7. An axial piston pump differs from a radial piston pump, as the pistons of an axial piston pump
are positioned _________.
radially from the shaft
parallel to each other and to the shaft
parallel to each other but at a right angle to the shaft
at an angle to each other and to the shaft
8. In reference to air conditioning, when air attains the maximum amount of moisture it can hold at
a specific temperature, it is said to be _____________.
superheated
saturated
condensed
convected
9. Positive displacement, helical gear pumps are well suited for pumping oil because
stuffing boxes eliminate the leakage problems usually associated with other gear pumps
it is not necessary to closely maintain design clearances this pump
they are essentially self-priming and produce a high suction lift
10. The conical steel or composition cone installed on a propeller, known as a fairwater cone,
provides which of the following benefits?
Reduce turbulence
Help with lubrication
Protect against electrolytic corrosion
All of the above
11. It is desirable for an auxiliary boiler safety valve to pop open and reseat quickly to
give warning that excessive boiler pressure has been reached
prevent wire drawing of the disc and seat
prevent valve pounding
provide sufficient blow down
multi b & d
10. The purpose of the programmed purge cycle on an automatically fired auxiliary boiler is to
cool the furnace to prevent pre-ignition
remove explosive vapors from the furnace
evaporate accumulated unburned fuel oil
provide sufficient air in the furnace to allow ignition of the fuel
12. Short cycling of a refrigeration compressor refers to _____________.
Frequently cutting out on over load.
frequently starting and stopping
running too fast
running too slow
13. The emergency bilge suction valve is typically used _____________.
to inject cleaning additives when the bilges are extremely dirty
when the main condenser becomes fouled, in order to provide additional cooling water
circulation
to connect the rose box to the independent bilge suction
if the bilges become flooded and they cannot be emptied by any other means
14. The by-products of oxidation, as a result of water contamination of hydraulic oil, are generally
____________.
removed by cellulose type filters
15. Which of the following describes the purpose of a striker or doubler plate?
Provides a surface for the application of force, or the installation of machinery.
Provides landing surface for the sounding bob of a tank sounding tape.
Absorbs machinery vibration.
Prevents valve stem over travel.
16. Which of the following statements represents the proper relative direction of flow through a globe
valve?
Direction of flow through the valve is unimportant.
Direction of flow through the valve depends upon the type of seat design used in the valve.
Direction of flow should be from below the seat.
Direction of flow should be from above the seat.
17. A portion of the cargo of an LNG carrier boils off during each voyage. How the cargo boils off is
normally handled?uscg15
Compressed, condensed, and returned to the cargo tanks.
Vented to the atmosphere.
Burned in the boilers.
Mixed with nitrogen and recirculated through the primary barrier.
Burnt off in a controlled manner through a chimney smoke stack from within the funnel.
18. In Vessel construction, beam brackets are triangular plates joining the deck beam to a
bulkhead
frame
stanchion
deck longitudinal
19. The cylinders and intercoolers of most low pressure air compressors are cooled by _uscg2022
water
oil
air
CO2
20. A one ton air conditioning system has which of the listed operating characteristics?
21. Which of the materials listed is used as the dynamic seal material on mechanical seals installed
on most centrifugal pumps used in water service?
Copper.
Copper and carbon.
Carbon.
Bronze.
22. When using a handheld hacksaw, you should apply pressure only on the forward stroke
____________.
only when cutting thin wall tubing
only when cutting carbon steel
only when cutting conduit
at all times
23. An important consideration in selecting a lubricating oil for use in a refrigeration compressor is
for the oil to ____________.
have a high viscosity index
mix readily with refrigerant
have a high freezing point
have a low pour point
24. If the intercooler relief valve lifts while an air compressor is operating under load, you should
check for ____
a defective pressure switch or pilot valve
a leak in the intercooler piping
leakage through the low pressure unloader control diaphragm
leaking high pressure discharge valves
25. Latent heat can be defined as the heat which must be added to a substance in order to change it
from a
solid to liquid
liquid to vapor
solid to vapor
all of the above
ductibility
elasticity
malleability
fusibility
32. One characteristic of a lubricating oil adversely affecting the results of centrifuging is
____________.
high TBN value
low oil floc point
low oil demulsibility
low oil neutralization number
33. Which of the devices listed prevents water from entering a ship's hull via the propulsion shaft?
Stern tube packing or mechanical shaft seal
Deflector ring and drain
Spring bearings
Oiler rings
34. With reference to a vessel's structural integrity, the most significant characteristic of a cryogenic
liquid is its ______________.
capability of causing brittle fractures
highly corrosive action on mild steel
vapor cloud which reacts violently with saltwater
toxicity at atmospheric pressure
35. The heat required to change a substance from a solid to a liquid while at its freezing temperature,
is known as the latent heat of _____________.
fusion
vaporization
condensation
sublimation
36. Which of the following problems occurring in a hydraulic system can be caused by the use of an
oil having a viscosity lower than specified?
Seal deterioration
Fast response and hunting
Increased power consumption
Oil film breakdown
37. The only means of removing the latent heat of condensation from a refrigerant in the normal
refrigeration cycle is by ________.uscg224
passing it through the expansion valve
condensing refrigerant in the system condenser
passing the gaseous refrigerant through the heat interchanger on the suction side of the
compressor
maintaining a high pressure on the system's receiver
38. Which of the following statements represents the main difference between a stuffing box gland
and a mechanical seal for sealing the shaft of a centrifugal pump?
Packed stuffing box glands are subject to wear, but mechanical seals are not.
Packed stuffing box glands must be cooled by the liquid being pumped, but mechanical seals do
not require cooling.
If packing fails, the pump can be kept running temporarily by tightening the gland, but if a
mechanical seal fails it must be totally renewed to stop the leakage.
The sealing surface of a mechanical seal is parallel to the shaft, but the sealing surface of a
packed gland is perpendicular to the shaft.
39. In a shell-and-tube type hydraulic fluid cooler, the amount of heat transferred from the hydraulic
fluid to the cooling water depends upon ________________.
the temperature of the hydraulic fluid
the flow rate of both the cooling water and the hydraulic fluid
the temperature of the cooling water
all of the above
40. The presence of scale and dirt on the saltwater side of lube oil cooler is usually indicated by
___________.
clogged lube oil strainers
seawater leaking into the lube oil system
decreasing lube oil pressure
gradually increasing lube oil temperature
41. The charging of a refrigerating system should be carried out by adding _____________.
refrigerant vapor to the receiver only
liquid refrigerant to the low side only
liquid refrigerant to the high side only
liquid refrigerant to the high or low side
42. A leaking suction valve in the second stage of a two stage, high pressure, air compressor can cause
excessively high ________________.
second stage discharge pressure
first stage discharge pressure
pressure in the after cooler
compressor final discharge temperature
43. Fabric type packing, such as flax or hemp, is best suited for _____________.
low temperature use
high temperature use
use where alignment is critical
packing valves with badly grooved stems
44. Which of the listed problems is occurring if a coil type high pressure evaporator constantly
requires an increase in the coil steam pressure in order to maintain capacity?
The brine density is improper.
Heat transfer surfaces are being layered with scale.
Impure distillate is being produced.
Shell vapor pressure is constantly decreasing.
45. The terms rough, coarse, bastard, second cut, smooth, and dead smooth refer to the ________.
shape of the file
coarseness of the file teeth
size of the file
cuts of the file
46. A pump is defined as "a device that _____________."
produces pressure
imparts energy to a fluid to move it from level "A" to level "B"
creates a vacuum to move a liquid in all installations
is to develop a pressure differential
47. Restrictions occurring in the small orifices of pneumatic control system components can be
caused by
moisture in the compressed air supply
excessive dryness in the compressed air supply
pressure surging in the compressed air receiver
48. The principal purpose of sub cooling liquid refrigerant prior to its entering the expansion valve is
to _
increase the refrigerating effect by decreasing the amount of flash gas
allow the refrigerant to enter the throttling device in a saturated condition
increase the refrigerating effect by increasing the amount of flash gas
minimize the temperature drop of the liquid as it passes through the solenoid valve to the outlet
side
49. If a bilge pump is able to develop vacuum, but is unable to sufficiently pump out the bilges, you
would check for ________.
the circuit breaker
for leaks in the suction piping
relief valve is not properly seated
the suction strainer
50. A first stage unloader installed in a low pressure air compressor is unable to completely retract.
This will result in ____
overheating of the discharge valve
loss of moisture in the air charge in the receiver
frequent lifting of the intercooler relief valve
an abnormally low intercooler pressure
51. The heat removed from the refrigerant in the condenser of a refrigeration plant is the
latent heat of expansion
sensible heat of condensation
heat of compression
all of the above
52. Excessive leakage and premature failure of valve packing is a result of ____________.
opening a valve too quickly
jamming a valve in the closed position
low pressure fluid flow through the pipeline
a scored valve stem
53. The amount of fuel oil atomized by a return flow oil burner is directly controlled by the
header supply valve
burner root valve
oil micrometer valve
fuel oil back pressure
54. Fuses are rated in _
voltage
amperage
interrupting capacity
all the above
6. When there is excessive ingress of water in the engine room onboard causing dangerous levels of
bilge water,
A. Start oily water separator and pump overboard
B. Start General service pumps and pump bilges overboard
C. Use bilge injection valve and pump bilges overboard
D. None of the above
7. If a radial piston hydraulic pump fails to deliver rated fluid volume, the cause can be
_______________.
contaminated fluid
pitted thrust rings
worn pintle bearings
obstructed suctions passage
8. A fluctuating and unsteady vacuum in an evaporator may be caused by _____________.uscg99
1. wet steam entering the air ejector nozzle
2. pinhole leaks in the evaporator tube nests
3. rapid scaling on the evaporator tube nests
4. high water levels in the last effect
9. A generator has been exposed to water and is being checked for its safe operation. Therefore, it is
necessary to _______________.uscg272
check for shorted coils with a explosimeter.
take moisture readings with a hydrometer
10. If the pointer fails to return to zero when a megger is disconnected, the_____________.332
pointer is stuck
hair springs are burned out
megger is out of calibration
megger is operating normally
11. When replacing ball bearings on an electric motor shaft, you should _____________.318
(a) tap the outer race with a mallet
(b) apply even pressure to the outer race
(c) apply even force to the inner race
(d) apply pressure evenly to both the inner and outer races
62. The zipper of an immersion suit should be lubricated with _____________.
paraffin
oil
graphite
vegetable oil
63. An insulation resistance test is performed on a particular piece of electric equipment. In addition
to the resistance reading, what information listed below should be entered in the electrical log?
(a) The maximum allowable operating temperature of the machine.
(a) The temperature of the machine at the time the resistance reading was taken.
(b) The normal temperature rise of the machine.
(c) The complete name plate data from the resistance test instrument used to obtain the reading.
64. When removing the cap from a sounding tube on a MODU, the sound of air escaping indicates.
a. the tank is full
b. the tank may be partially flooded
c. the tank level has dropped
d. the tank is completely flooded
65. A solid stream of water might be useful in fighting a burning oil fire on deck when it is used
____________.
a. to wash burning oil over the side
b. to provide cooling for the fire fighters
69. While starting a hydraulic anchor windlass, you observe that hydraulic pressure does not develop
in spite of the proper operation of the electric drive motor. Which of the following actions should you
take FIRST to restore pressure?
Make certain that the hydraulic reservoir is filled to the proper level.
Inspect the disc brake on the electric motor for proper operation.
Check the electric motor for an open overload relay contact.
Check for full voltage supply to the electric motor.
70. A primary element used with flow measurement devices highly suitable for liquids containing
solids in suspension, is a ____________.
a. concentric orifice
b. convergent nozzle
c. venturi tube
d. pilot tube
72. Prior to major overhaul of main engine onboard, the engine room crane is tested by
A. Operating the crane through the normal range
A. Globe Valve
B. Butterfly valve
C. Gate Valve
D. Full bore angle valve
83. Which of the following types of steam traps uses the pressure energy of the steam to close the
outlet ?
A. Thermostatic trap
B. Thermodynamic trap
C. Mechanical trap
D. Vacuum trap
84. Sequential starting of machineries after black out in engine room is necessary
A. To prevent overload of Generators
B. To quickly restore the failed power supply in order
C. To prevent damage to machinery which has been switched off
D. All of the above
85. Salinity of distilled water produced from fresh water generator onboard depends on
A. Amount of feed set in fresh water production
B. Amount of salt water leaking from condenser if any
C. Temperature of the sea water used
D. Efficiency of brine ejector from the evaporator shell
86. Which of the following is the material used for manufacturing tube plates of a shell and tube type
heat exchanger?
A. Cupro-nickel
B. Aluminum Brass
C. Admiralty Brass
D. Gunmetal
87. How is the water circulated between water and steam drums in a water tube D- type boiler?
90. Water leaking from a pump packing gland is kept away from the bearing housing by the use of
shaft sleeves
lantern rings
water defectors water flinger
water seals
SECTION 4
TAKEN FROM DG SHIPPING OLD QUESTION
1. Which of the following conditions should be used to support the need to change the lube oil when there
has been an increase in the neutralization number?
A decrease in the viscosity of the oil
An increase in the viscosity of the oil
A change in the cloud point
2. A casing drain is provided for axial piston and bent axis variable stroke pumps to ___________.
vent off any accumulated air from the system
drain off any accumulated water from the pump casing prior to its being started
assist the complete removal of hydraulic oil from the system prior to opening for major or
minor repairs
prevent damage due to agitation and overheating of oil accumulated in the casing as a result of
minor internal leakage
3. Increasing the speed of a rotary pump above its rated speed will result in most of the following
conditions to occur?188
Increased suction
Increased clearances
Vibrations
slippage
4. After packing is added to the stern tube stuffing box, which of the following procedures should be
observed to insure even tightening of the gland?193
Listen for a smooth, regular sound.
Measure the distance between the gland and the stuffing box with a rule.
Judge by feeling the gland for an increase in heat as it is being tightened up.
Open the drain connection to allow seawater to flow in and make the distance even.
5. The temperature at which water vapor in the atmosphere begins to condense is called the
____________.
dew point temperature
condensation temperature
psychometric temperature
absolute humidity temperature
6. One function of the air receiver in a compressed air system is to _____________.
dry the air discharged from the intercooler
minimize the system's line pulsations
receive exhaust air from pneumatic accessories
remove all traces of oil from the air
7. Which of the following statements describes the purpose of the split inflatable seal installed aft of
the primary seal assembly for the propeller shaft?197
To serve as a seal when adding packing to the stuffing box.
To allow repair or replacement of the primary seal elements when the ship is waterborne.
To eliminate leakage via the propeller shaft when the shaft is not rotating.
To provide a ready means for the entry of cooling water.
8. Why should a person performing maintenance on an air compressor wire and tag the system
valves closed?
To prevent the unexpected.
To protect the equipment.
To protect the operator performing the maintenance.
Each of the above is correct.
9. One of the main differences between the various types of screw pumps is in the __________.
stuffing box diameter
direction of rotation of the screws
pitch of the screws
type of driving gears
10. The FIRST thing to do to ensure that a refrigeration unit will not start while undergoing repairs,
is to ____________.
secure and tag the electrical circuit
place a crow bar in the flywheel of the unit
inform all persons in the area not to start the unit
make a log book entry
11. At which of the following locations would a duplex pressure gage most likely be located?
Fuel oil service pump discharge flange
Fuel oil strainer
Fuel oil heater
Fuel oil flow meter
12. In any air system a safety device should be placed between any two points where air can be
trapped between any two valves.
(a) Which can be closed manually.
(b) Between a non return valve and a screw down valve.
(c) Between a non-return valve and a U-bend of a pipe.
(d) Between any valve and a nozzle.
13. Some of the following are preferred refrigerants of the future
(a) Carbon dioxide
(b) Refrigerant 11
(a) Refrigerant 502
(b) Ammonia
(c) Bromine
(d) Argon
14. In the air conditioning of a ship a Comfort Zone constitutes
(a) Low humidity, low room temperature
(b) Low humidity, moderate temperature
(c) High humidity, moderate temperature
(d) Very low temperature, moderate humidity
15. The passenger spaces of a passenger ship is protected against major fires by a
(a) High expansion foam system
(b) High density CO2 system
(c) By a mixture of fire detection, fire retardant, A-1 class bulkhead, fire doors, fire insulation and
elabrate sprinkler system.
(d) High pressure steam system.
16. Sand impregnated with chemicals is kept in metal containers with a shovel, in the engine room, for the
following purposes
(a) to cover small oil spills
(b) to use along with cement for doing repair jobs.
(c) for making the floor anti-skid by giving more friction.
(d) for use as grinding paste in case of emergency.
17. Which of the processes listed, consumes the greatest amount of power while producing the greatest
amount of heat?
Overcoming sliding friction
Overcoming rolling friction
Overcoming fluid friction
Overcoming oil wedge friction
18. Which of the following guidelines is considered to reflect good design practices of shipboard
steam heating systems?
Provide constant steam service for equipment operating throughout the year.
Provide either a common or individual reducing station for each group of units requiring the
same operating pressure.
Run all piping so it may be drained by gravity.
All of the above.
19. A distinguishing feature of an eductor, when compared to other pumps, is the ______________.
discharge end being smaller than the suction end
small size of impeller
lack of moving parts
ease at which the wearing rings may be changed
20. When securing a flash-type evaporator for an extended period of time, you should _____________.
fill the unit with saltwater
fill the unit with descaling compound
completely drain the unit
tightly seal the unit to exclude air
21. The portion of a hydraulic hose that determines its overall strength, is the _____________.
inner tube
braided inner layer(s)
outer cover
outer armor
22. Which features of a centrifugal pump reduce the need for renewing worn impellers and pump casings?
Close radial clearance between impeller hub and casing
Low rotational speed of impeller
Removable end plate
Replaceable impeller and casing wearing rings
23. An acceptable method of dealing with accumulated oil found in the pump room bilges is to
______________.
transfer the oil to the sea chest
pump the oil into the slop tanks
discharge the oil over the side on an outgoing tide
pump the oil into a clean ballast tank
24. A ship is required to carry an Oil Record Book, and must maintain the book as per rules on board for
_______________.
1. one year
2. two years
3. three years
4. four years
25. Which of the following actions, pertaining to saltwater lubricated stern tube stuffing boxes, is usually
observed when the ship is expected to be in port for an extended period?
The stuffing box is continually flushed.
The drain connection is left opened.
The stuffing box gland is tightened.
The packing is adjusted for greater cooling or replaced.
SECTION 5
1. A high pressure differential in a main engine fuel oil filter onboard can be best reduced by
A. Back flushing the filter manually
B. Stopping the main engine to change the filter element
C. Changing over to stand by filter if provided
D. None of the Above
2. Inert Gas System should be capable
least____________________________
of
delivering
Inert
Gas
at
the
rate
of
at
6. The term referring to the number of teeth per inch on a hacksaw blade is known as the
A. Set
B. rake
C. pitch
D. thread gauge
7. The ash content of a fuel oil is significant to the operating engineer because it 117
A. is an indication of the amount of noncombustible material present in the oil
B. indicates the quantity of energy released by burning a unit amount of the fuel
C. is useful for determining proper atomization temperatures
D. reflects the overall thermal efficiency of the fuel oil service system
8. Air conditioning system air handling units must have their air filters cleaned at regular intervals
in order to prevent______
A. Growth of microorganisms and bacteria harmful to human beings
B. Restriction to air flow and hence reduced efficiency of the plant
C. Growth of mites and other allergens
D. All of the above
9. Amount of distilled water produced in fresh water generator onboard decreases with
A. Increase in vacuum in the fresh water generator shell
B. Decrease in sea water temperature
C. Decrease in efficiency of heat exchanger
D. Increase in sea water temperature
10. Before any work is to be carried out on a burner in an automatically fired auxiliary boiler, you
should always
A. block all control system relays closed
B. allow the boiler to cool completely
C. close all manually operated fuel valves
D. lock all safety interlock switches closed multi a c d
16. Injecting water into the combustion chamber of marine engines is a primary method of reduction
of which of the following air pollutants?
A. SOx
B. Particulate matters
C. Unburnt Hydrocarbons
D. NOx
17. In case of failure of control air supply ,some valves continue locked in the position they were at
the time of failure . They are said to beA. Fail-safe
B. Fail -proof
C. Fail-set
D. Fail -blocked
18. Old machinery space log book are kept in safe custody
A. To refer and clarify in case of any query
B. For purpose of internal and external audits
C. To safeguard the chief engineer???s competence
D. None of the Above
19. If the superheat value of a thermostatic expansion valve is set too low________
A. The suction line of the compressor will be too hot
B. The suction line of the compressor will be too cold
C. The discharge line of the compressor will be too hot
D. The discharge line of the compressor will be too cold
20. Which of the following chemical compounds prevents caking of powder in dry chemical powder
fire extinguisher?
A. Sodium Stearate
B. Sodium Bicarbonate
C. Magnesium Stearate
D. Magnesium Bicarbonate
B. Builder's documentation
C. Certificate of Inspection
D. Construction portfolio
32. Water hammer in a steam heating system can be caused by
A. filling the auxiliary boiler with cold water
B. steam admitted to a cold pipe
C. filling the auxiliary boiler with hot water
D. draining a soot blower line before cracking the steam supply valve
33. What is a function of the wearing rings used in most centrifugal pumps?
A. Absorb erosion of high velocity discharge stream
B. Seal pump shaft against entry of air
C. Isolate the discharge side from the suction side
D. Dampen the turbulent discharge flow
34. Which combination of the main shaft segments listed below, that are located furthest from the
main engine, are connected by the inboard stern tube shaft coupling?
A. Line shaft and thrust shaft
B. Line shaft and stern-tube shaft
C. Thrust shaft and stern-tube shaft
D. Stern-tube shaft and tail shaft
35. An auxiliary engine turbo-charger makes strange noises when the load changes. The engine
parameters however are absolutely fine. An external examination of turbocharger parameters as
stated in the manual also reveals nothing. Would you
(a) Continue to run the engine and wait for some time
(b) Stop the engine for a while and make some checks
(c) Reduce the load of the engine
(d) Run it on steady load to make some checks.
36. Which of the following can be done to reduce the cold corrosion of Main Engine cylinder liners
using high sulphur fuel oil :-
A. Type a
B. Type b
C. Type a and b
D. None
14. Surging indicates
A. Scavenge fire
B. exhaust manifold fire
C. Fault in fuel system
D. All
15. Engine cylinder relief valve lift indicates abnormal of what.
A. Fuel supply
B. Fuel injection
C. Exhaust temp
D. Exhaust pressure
16. Hydride formation in gas carrier can lead to a
A. Contamination of cargo
B. Seize of pump
C. Exothermic reason
D. None
17. Deep well cargo pump used in
A. Chemical carrier
B. Product carrier
C. LNG
D. All
SECTION NEW - 1
1. Which of the following statement is true if the oil temperature is allowed to become excessively
high in the heaters?
A. Excessive temperature will increase oil viscosity that results to poor combustion
B. Excessive temperature will cause the oil to crystallize resulting in pulsating fires
C. The fuel will carbonize and its heating ability will be reduced
D. The fuel will ignite even it has not reached point of ignition
2. A drop in compression pressure in one cylinder of a diesel engine can be caused by ___________.
a. only fuel injection
b. burned valves
c. too late fuel injection
d. low fuel penetration
Some diesel engines are fitted with a thermometer in the cooling water outlet from each cylinder. If
the cooling temperature from an individual cylinder begins to rise, what should you suspect?
a. That there is an overloading of cylinder
b. That there is an overloading of the adjacent
cylinder
c. That there is an increase blow-by of the cylinders
d. That there is an incomplete combustion in that cylinder
Which of the listed actions should be carried out if a ship is to be laid up for an indefinite period of
time ______.
I Boilers to be laid up wet should be completely filled
II All fuel tanks should be cleaned & gas freed
III All potable water tanks should be cleaned & disinfected
A. I only
B. II only
C. I & II
D. I, II & III
B. 0.04% Cobalt
C. 0.04%Arsenic
D. 0.04%Tungsten
One cause of leaky valves in a low pressure air compressor may be attributed to
A. running with an air filter element different from that required by the original manufacturer's
specifications
B. excessive operating hours without carrying out preventive maintenance
C. the compressor running too fast
D. excessive discharge pressure
The static suction lift of a pump is the difference in elevation between the
A. centerline of the pump and the level of the liquid in the suction well when the source of liquid is below
the pump
B. centerline of the pump and the suction liquid level when
the source of liquid is above the pump
C. centerline of the pump and the level of the discharge liquid
D. liquid levels of the suction and discharge
Plate type heat exchangers are preferred over shell and tube type ones because____________
A. They can be cleaned more thoroughly .
B. Their capacity can be altered by adding or removing plates.
C. Turbulent flow and more margin for increased fluid velocity ensures less deposits and hence longer time
interval between cleanings.
D. All of the above
Inert Gas System should be capable of delivering Inert Gas at the rate of at east_________________
A. 110% of the maximum rate of cargo discharge capacity of the ship
B. 133.33% of the maximum rate of cargo discharge capacity of the ship
C. 125% of the maximum rate of cargo discharge capacity of the ship
D. 90% of the maximum rate of cargo discharge capacity of the ship
Preferential tripping of electrical machineries prevents
A. Overloading of generators
B. Black out in engine room
C. Allows starting of large machineries
D. None of the above
Which is the only gas product ,allowed by gas codes, to be burnt in ship's boilers?
A. LPG
B. Ethylene
C. Butane
D. LNG
Frequent cutting- in & cutting -out of a fresh water pump on a hydrophone system indicates which
of the following?
A. Nothing abnormal
B. Excessive air charge
C. Insufficient air charge
D. The differential setting between cut-in and cut out is too low
Economisers are built up with
A. Copper tubes
B. Plain steel tubes
C. Stainless steel tubes
D. Steel tubes fitted with shrunk on C.I. grills single d
35.You must have worked with mooring winch and windlass hydraulic systems. The cooling of
hydraulic oil for the above system on large merchant ships is provided by:
A. There is no cooling arrangement as the system doesn???t require cooling
B. Air cooled hydraulic reservoir
C. Water cooled plate or shell type heat exchangers
D. Radiator and fan arrangement
1.In case of failure of the control system of a centrifuge,the correct sequence for manually desludging
a purifier would beA.Stop feed-give sealing water-close sealing water -shut operating water-open and close desludging water
quickly
B.Stop feed- shut operating water-open and close desludging water quickly
C.Shut operating water-stop feed- open sealing water for a short time then close-open and close desludging
water quickly
D.Shut operating water- stop feed- open and close desludging water quickly
3.Liquid ring primer used for priming main and emergency fire pumps onboard
A.Is to be filled with water in the water tank to maintain water level
B.Is to be capable of automatic engagement and disengagement with drive shaft
C.Is to have sufficient capacity to exhaust air out from pump in all sea conditions
D.All of the above.
5.To prevent electric shock during electric arc welding
A.Wear dry clothes
B.Wear insulated shoes
C.Keep first aid equipment ready
D.None of the above
6.Back pressure valve in a refrigeration system with multiple chambers is fitted_____________
A. At the refrigerant exit end of evaporator of each chamber
B. At the refrigerant exit end of evaporators of chambers with higher temperature settings
C .At the refrigerant exit end of evaporators of chambers with lower temperature settings
D .None of the above
7.Inert Gas System on board tankers is used during which of the following operationsA. Inerting of empty tanks
B. Inerting during crude oil washing
C. Purging before gas freeing
1.In case of an exhaust gas boiler fire ,which of the following is a suitable control measure?
A. Start frequent soot blowing
B. Increase main engine speed to blow away the soot particles on fire
C. Stop cooling water circulation to avoid leakage
D. None of the above
3.Refractory damage in boiler furnace onboard is caused due to
A. Presence of moisture in the boiler before startup
B. Rapidly fluctuating temperatures inside boiler furnace
C. Overheating of boiler tubes due to lack of heat transfer from tubes due to scale
D. Boiler panting and vibrations
4.An economizer uptake fire in the engine room is extinguished by
A. Boundary cooling of the uptake
B. Injecting fixed fire fighting system if provided
C. Injecting water from the uptake
D. None of the above
LNG STORAGE AND PUMPING DETERMINED BY WHAT PROPERTY
a. VAPR PR
b. PARTIAL VPR PR
1. Which of the refrigerants listed is considered safe and ideal for most
marine applications?
-R-21
-ammonia
-R-12
-sulfur dioxide ans c n its r 22
2. In reference to air conditioning, when air attains the maximum amount
of moisture it can hold at a specific temperature, it is said to be
-superheated
-saturated
-condensed
-convected
3. Which of the following terms represents the form of heat removed from
the refrigerant in the condenser of a refrigeration system?
-latent heat of vaporization
-heat of compression
-superheat
-all of the above
4. The temperature at which water vapor in the atmosphere begines to
condense is called the
-dew point temperature
-condensation temperature
-psychrometric temperature
-absolute humidity temperature
5. In a refrigeration system, the refrigerant absorbs the latent heat of
vaporization in the
-compressor
-condenser
-receiver
-evaporator
6. The only means of removing the latent heat of condensation from a
refrigerant in the normal refrigeration cycle is by
-copper
-plastic
-steel
15. When handling contaminated oil from a hermetically sealed refrigeration
compressor unit that has burned out its motor, you should
a.store the oil in a clean refrigerant drum
b.use rubber gloves
c.circulate the oil through a filter drier
d.remove the oil with a portable charging cylinder
16. When replacing ball bearings on an electric motor shaft, you should
-tap the outer race with a mallet
-apply even pressure to the outer race
-apply even force to the inner race
-apply pressure evenly to both the inner and outer races
17. People familiar with ammonia refrigeration systems become accustomed
to its odor and may forget that the vapors
-in a low concentration can cause death
-will dissolve in pespiration and cause caustic burns
-will burn or explode
-all of the above
18. Ammonia when used as a refrigerant is valuable because of its high
efficiency, it is however
-toxic
-flammable
-explosive
-all of the above
19. When subjected to high heat from an open flame, or an electric heating
element, which of the listed refrigerants will break down and produce
phosgene gas?
-CO2
-methyl chloride
-R-22
-sulfur dioxide
20. When the relief valve opens it discharges high pressure refrigerant
vapor to the
-liquid strainer
-refrigerant inlet of the condenser
-inlet side of the evaporator
-suction side of the compressor
21. In the presence of an open flame or hot surfaces, chlorinated
fluorocarbon refrigerats decomposes and form
-petroleum crystals
-phosgene gas
-water vapor
-carbon monoxide
22. R-12 is generally considered to be a safe, nontoxic, nonflammable,
and nonexplosive refrigerant. It can, however, become highly toxic when
-superheated outside the system
-in contact with an open flame
-heated to the boiling point
-all of the above
-all refrigerant must be pumped into the receiver before adjustments are made
-time must be allowed for conditions to stabilize in the evaporator before
further adjustments are made
-all refrigerant must be routed through the dehydrator while changing the
superheat setting
59. A thermostatic expansion valve is properly controlling evaporator
superheat. Adjusting this valve to lower the superheat will result in a/an
-evaporator pressure decrease
-evaporator coil over-feed
-evaporator capacity increase
-expansion valve diaphragm rupture
60. Low compressor head pressure in a refrigeration system can be caused by
-insufficient condenser cooling water
-excessive condenser cooling water
-air in the refrigeration system
-excessive refrigerant in the system
61. Which of the problems listed would cause the discharge temperature of
an R-12 refrigeration compressor to increase?
-thermal expansion valve frozen open
-suction gas heat exchanger bypassed
-condenser clogged or fouled
-high pressure cutout switch inoperative
62. One cause of high head pressure occurring in a refrigeration system can
be
-insufficient cooling water flow to the condenser
-a low refrigerant charge in the system
-the liquid valve is open too much
-high evaporator superheat
63. If the head pressure of a reciprocating refrigeration compressor is
excessive,
-the relief valve should open before the high pressure cutout
-the relief valve should open and allow the excess refrigerant to flow to
the receiver
-the high pressure cutout switch should operate before the relief valve opens
-you should close in on a suction valve
64. If the refrigeration compressor was developing higher than normal
discharge pressure, this could be a result of
-air or non-condensable gases in the system
-leaking discharge valves
-leaking suction valves
-liquid refrigerant flooding back from the cooling coil
65. If the water failure switch should fail to shut down the refrigeration
compressor, the refrigerant pressure will build up in the high pressure side
of the system to the point where the
-compressor discharge valves would be damaged
-condenser tubes would rupture
-system relief valve would open
-high pressure cutout switch would function
66. High suction pressure to a refrigeration system compressor is caused by
-the expansion valve is insufficiently opened
would result in
-continuous running of the compressor
-high suction pressure
-high discharge pressure
-short cycling of the compressor on the water failure switch
76. A warmer than normal compressor suction line might be caused by
-insufficient lubrication
-insufficient refrigerant
-excess refrigerant
-excessive opening of the expansion valve
77. Which of the conditions listed will cause a refrigeration compressor
to run constantly without simultaneously decreasing the temperature in the
refrigerated space?
-shortage of refrigerant oil
-slight shortage of refrigerant
-excessive condenser cooling water flow
-faulty expansion valve
78. Frost appearing on the evaporator coils of a multi-box direct expansion
refrigeration system
-is best removed by means of ice pick
-will increase the refrigeration effect
-can be removed by passing hot vapors through the coils
-can be quickly removed by simply shutting down the coils
79. In a compression refrigeration cycle, the temperature of the liquid
refrigerant experiences its greatest decrease in the
-evaporator
-compressor
-expansion valve
-condenser
80. An increase in the heat load to a refrigeration system will cause
-the suction pressure to decrease
-the suction temperature to increase
-increased ice formation on the evaporator coil
-excessive short cycling of the compressor
General New Qs(MARCH & APRIL):1) Perfect cooling means in air comp??
2) How many hours we can work in threshold limit condition in some room???
8 hrs a day or 40 hrs a week
3) Function of hunting gear
a. All the above 3 other don remember
4) If 16 kw draw in 380 rpm how much kw it will draw if we reduce the rpm to 350??
P directly cube of rpm sayad (12.5kw by this formula)
5) For good purification in purifier we set feed rate low or high?
6) What sort of hardness due to mg, carbonates etc?
ANS:- (Permanent)
7) Gauging of safety v/v is done when??
ANS:- (for pr testing)
8) Boiler feed water pp casing and impeller material??
ANS:- (casing cast steel & impeller stainless steel)
9) Stearing gear 100% capability??
10)
Fan characteristic curves two questions
11)
Good housekeeping??
12)
Vacuum testing of evaporator??? Abc
13)
Two tube end joint- swaging???
14)
Hacksaw pitch??
15)
Cause of HP trip?? all the above is ans
16)
Hot work not permit ----all of above
17)
Specific gravity of centrifugal pump increases
a. Head n efficiency decreases
b. Power consumption increases
18)
Which one is not a variable delivery pump??
Gear or screw
19)
Three methods of surface hardening of ferrous
20)
Welding of steel and aluminium??
TIG( tig used for dissimilar metals so most apt)
21)
FD fan power 16 kw, rpm 800 if it is reduced to 600, what will be new power??
( by P pro to cube of rpm 6.75kw)
22)
Sensible heat + latent heat(total capacity)
23)
No of impeller helps to decidesingle stage and multi stage
24)
Prior to entry to LNG tank?? warming
25)
Low carbon steel case hardening process??
26)
Relation bw cent pp Q & power relations??
27)
Free rotation of turbocharger???
28)
Slow and delay combustion effect on exh gas??
29)
Advancing of injection. Effect on power and exh gas??
30)
The RPM of d is 600 and hobbed teeth 46. If gears a b c have 94,80,30 teeth.
How to find RPM of a ??
( this q has a fig , use N1.D1=N2.D2)
New
1) Remote location to shut off ER FO p/ps ( multiple)
a. ECR
b. Wheel house
a. general plans
b. builder's documentation
c. Certificate of Inspection
d. construction portfolio
13)
A continuous watertight bulkhead on a MODU may also be a/an
__________.( uscg 9)
a. structural bulkhead
b. exterior bulkhead
c. centerline bulkhead
d. joiner bulkhead
14)
Enlarging one tube end so the end of another tube of the same size
will fit inside is termed __________.(uscg 94)
a. Belling
b. Stretching
c. Flaring
d. Swagging
15)
The purpose of annealing any metal is to make the metal _______.(uscg
96)
a. Softer
b. Smoother
c. Harder
d. Tougher
16)
The floating end of a shell-and-tube type cooler utilizes a packing ring
to __________.(uscg 108)
a. prevent leakage past the floating end tube sheet
b. dissipate heat
c. baffle cooling water so it can be directed on a multiple pass
d. modify to a mixer type cooler
17)
Water hammer in a steam heating system can be caused be____.(uscg
167)
a. filling the auxiliary boiler with cold water
b. steam admitted to a cold pipe
c. filling the auxiliary boiler with hot water
d. draining a soot blower line before cracking the steam supply valve
18)
who takes radial thrust in pumps
a. volute casing
b. partition of double volute casing
c. roller bearing
d. none
19)
In case of uptake fire , fire can be extinguished by.(mcq)
a. Boundary cooling
b. Fixed fire installation
c. Using water directly
d. None
20)
In variable delivery system how can maximum energy can be
generated by which configuration
a. Pure static head
b. Pure friction head
c. High static n low friction head
d. Low static n high friction head
21)
Internal FO transfer
a. Regularly check ullage and sounding
b. Inform CO to confirm the list /trim
c.
32)
a.
b.
c.
d.
33)
a.
b.
c.
d.
34)
a.
b.
c.
d.
35)
a.
b.
c.
d.
36)
a.
b.
c.
d.
37)
a.
b.
c.
d.
Inerting
ME LO temp
60
65/70
75/100
Don remember
What is the function of steam drum
Collect steam
Collect water
Equalize water in generating tubes
Collect salt deposit
Welding procedure of MODU is kept where??
Vessel plan
Coast guard file
Construction portfolio
Certificate of inspection
Liquid pumping in lng depends on ( a or d)
Vap pr
Absolute pr
Partial pr
Partial vap pr.
Purpose of telemotor bypass valve
Top up the hydraulic oil
As a relief valve
Equalize the two line
All
Air comp performance depends on
Vane angle
Dia of impeller
Don rem
All
19)cylinderchrome plate
a)pearlite CI
b)also chrome
c)stellite
20)furnace backpressure
a)Acc. of oil
b)Incorrect purge timing
c)both a n b
d)
21) over speed shutdownfuel racks getting stuck and faulty governor,
Racing n jumping of propeller in bad weather
a)Governor..single
b)Fuel system..mcq
c).d)
FEB 2014
22)COP is a function of
A)condenser
b)evaporator
c)both a n b
d)none of the above
23)sewage treatment plant procedure
a)settling-aeration-chlorination-overboard
b)aeration-settling-chlorination-overboard
c)settling-chlorination-aeration-overboard
d)chlorination-aeration-settling-overboard
24)identical fans are kept in series
a)discharge pressure doubles
b)static pressure doubles
c)static pressure becomes four times
d)discharge pressure is 4 times
25)rudder stock is moved 230mm and above then in steering gear
a)one pump is used
b)both pumps are used
c)..d)..
26)volatility of petrol ,keroseneans..petrol
APRIL 2014
27)deflection of arc during welding is called
a)Lack of fusion
b)Distortion
c)Lack of penetration
d)Arc slag/blow
28)At which of the dew point temperature, air will have least moisture content
a) 10oC
b) 20oC
c) +30oC
d) 40oC
29)For sub zero applications the secondary coolant normally used is:
a) Chilled water
b) Brine
c) Lithium Bromide
d)Ammonia
30)Method of producing power by steam of boiler is called
a)Co generation
b)Extraction
c)both a n b
d)neither a nor b
31)boiler turn down ratio for y jet type oil burner(answer from Flanagan book)
a)10:1
b)20:1
c)5:1
d)2:1
32) NPSHa definition (forgot options)
33)Minimum pressure testing for low pressure boiler
a)15 bar
b)20 bar
c)205bar
d)None of the above
34) The discharge head of a centrifugal pump will vary directly with the
A) Change in impeller diameter
B) Square of the impeller diameter
C)Cube of the impeller diameter
D)Impeller efficiency for large changes in the size of the impeller
35) Pump power is directly proportional to the of pump impeller diameters
A) No change
B) Square
C)Cube d3
D)None of the above
36)0.83% carbon indicates
A) Pearlite
B) Cementite
C)Ferrite
D)None of the above
37)Air reservoir is not used for
A) Collect air
B) Remove pulsation from system
C)..
D)Increase pressure of air
38)The pressure of refrigerant in vapour compression system changes in
a)
b)
c)
d)
Compressor
Evaporation
Expansion valve
Both (a) & (c)