Beruflich Dokumente
Kultur Dokumente
053 0137
M ASTERSHEET
Revision 04/11/06
IMPORTANT
1.
2.
3.
4.
Side Brackets
Receiver Trimpanel
Tools required:
phillips
screwdriver
*0000530137*
053 0137
Reassembly
Wiring
Inspect factory receiver harness connector in vehicle. Ensure that the wiring adaptor purchased from Crutchfield
plugs into the vehicles connector. If the connector is missing or cannot be located, please call our Technical
Service department at 1-800-955-9094.
Kit Assembly
Assemble receiver and kit following instructions supplied with the installation kit.
Harness Connection
NOTE: If your vehicle is not equipped with an antenna,
proceed now with Antenna Installation, page 4.
1.
2.
3.
4.
Receiver Assembly
Accessories Assembly
Faceplate
Tools required:
Mounting Holes
phillips
screwdriver
Receiver Trimpanel
deep socket
Control Knobs
Shaftnuts
2
053 0137
Reassembly
Wiring
Inspect factory receiver harness connector in vehicle. Ensure that the wiring adaptor purchased from Crutchfield
plugs into the vehicles connector. If the connector is missing or cannot be located, please call our Technical
Service department at 1-800-955-9094.
Kit Assembly
Assemble receiver and kit following instructions supplied with the installation kit.
Harness Connection
NOTE: If your vehicle is not equipped with an antenna,
proceed now with Antenna Installation, page 4.
1.
2.
3.
INSET
Factory Brackets
Receiver/Accessories Assembly
Mounting Holes
Tools required:
1-800-955-9094
Technical Service
phillips
screwdriver
3
053 0137
Antenna Replacement
1.
2.
3.
Antenna Base
Pillar
Tools required:
1-800-955-9094
phillips
screwdriver
Technical Service
string
R
R
053 0137
Instructions show factory size
speakers only. Cutting,
fabricating, or speaker adaptor
brackets (not shown) will be
required for other size speakers.
Speaker Replacement
Speaker Wiring Connect speaker wiring adaptors to speakers following adaptor instruction sheet.
INSET
C Clip
1.
2.
3.
4.
SAFETY CHECK
Armrest
Door Panel
Tools required:
5.
phillips
screwdriver
6.
panel tool or
rigid putty knife
7.
8.
shop rag
R
R
1-800-955-9094
Technical Service
wire cutters
5
053 0137
Speaker Replacement
Speaker Wiring Connect speaker wiring adaptors to speakers following adaptor instruction sheet.
1-800-955-9094
Technical Service
1.
2.
3.
4.
C Clip
SAFETY CHECK
Armrest
Door Panel
Tools required:
5.
6.
7.
1-800-955-9094
6
Technical Service
phillips
screwdriver
panel tool or
rigid putty knife
shop rag
053 0137
Instructions show factory size
speakers only. Cutting,
fabricating, or speaker adaptor
brackets
(notshow
shown)
will be
Instructions
factory
size
required for other size speakers.
Speaker Replacement
Speaker Wiring Connect speaker wiring adaptors to speakers following adaptor instruction sheet.
FIGURE 1
Retaining Clip
FIGURE 2
Door Release Cup
C Clip
FIGURE 3
Door Panel
Armrest
Tools required:
phillips
screwdriver
panel tool or
rigid putty knife
SAFETY CHECK
shop rag
wire cutters
7
053 0137
Instructions show factory size
speakers only. Cutting,
fabricating, or speaker adaptor
brackets
(notshow
shown)
will be
Instructions
factory
size
required for other size speakers.
Speaker Replacement
Speaker Wiring Connect speaker wiring adaptors to speakers following adaptor instruction sheet.
FIGURE 1
Retaining Clip
1. Press in center pin (Figure 1), then pry out one (1)
retaining clip from upper front area of door
panel.
FIGURE 2
Door Release Cup
C Clip
Door Panel
FIGURE 3
Armrest
Tools required:
SAFETY CHECK
panel tool or
rigid putty knife
R
R
1-800-955-9094
8
Technical Service
shop rag
053 0137
Instructions show factory size
speakers only. Cutting,
fabricating, or speaker adaptor
brackets
(notshow
shown)
will be
Instructions
factory
size
required for other size speakers.
Speaker Replacement
Speaker Wiring Connect speaker wiring adaptors to speakers following adaptor instruction sheet.
3.
Rear Speakers
(if vehicle is factory equipped with speakers)
1.
FIGURE 3
4.
5.
FIGURE 4
Retaining Clip
2.
Speaker/Bracket
Assembly
SAFETY CHECK
Tools required:
FIGURE 2
phillips
screwdriver
pliers
R
R
1-800-955-9094
Technical Service
small nail
9
053 0137
Instructions show factory size
speakers only. Cutting,
fabricating, or speaker adaptor
brackets (not shown) will be
required for other size speakers.
Speaker Replacement
Speaker Wiring Connect speaker wiring adaptors to speakers following adaptor instruction sheet.
3.
Rear Speakers
(if vehicle is not factory equipped with speakers)
1.
FIGURE 3
FIGURE 1
Cut-Out Area
2.
FIGURE 2
Tools required:
phillips
screwdriver
pliers
Retaining Clip
utility knife
R
R
10
small nail
053 0137
Speaker Replacement
Rear Speakers (continued)
(if vehicle is not factory equipped with speakers)
4.
5.
6.
FIGURE 4
FIGURE 5
Screw Anchors
Speaker/Bracket
Assembly
SAFETY CHECK
R
R
1-800-955-9094
Technical Service
11