Beruflich Dokumente
Kultur Dokumente
A1SAM-2550F
A1SRM-2758F
A1SRM-2558F
USERS MANUAL
Revision 1.0
The information in this users manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our website at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between the manufacturer and the customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturers instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Preface
Preface
This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use of
the
A1SAM-2750F/A1SAM-2550F/A1SRM-2758F/A1SRM-2558F motherboard.
Manual Organization
Chapter 1 describes the features, specifications and performance of the motherboard, and provides detailed information on the Intel C2000 SoC processor.
Chapter 2 provides hardware installation instructions. Read this chapter when installing the processor, memory modules and other hardware components into the
system. If you encounter any problems, see Chapter 3, which describes troubleshooting procedures for video, memory and system setup stored in the CMOS.
Chapter 4 includes an introduction to the BIOS, and provides detailed information
on running the CMOS Setup utility.
Appendix A provides BIOS Error Beep Codes.
Appendix B lists software program installation instructions.
Appendix C contains UEFI BIOS Recovery instructions.
iii
iv
Contacting Supermicro
Contacting Supermicro
Headquarters
Address:
Tel:
+1 (408) 503-8000
Fax:
+1 (408) 503-8008
Email:
Web Site:
www.supermicro.com
Europe
Address:
Tel:
Fax:
Email:
Asia-Pacific
Address:
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3992
Web Site:
www.supermicro.com.tw
Technical Support:
Email:
support@supermicro.com.tw
Tel:
+886-(2)-8226-3990
Table of Contents
Preface
Chapter 1 Introduction
1-1 Overview.......................................................................................................... 1-1
1-2
1-3
Special Features.............................................................................................1-11
1-4
PC Health Monitoring......................................................................................1-11
1-5
ACPI Features.................................................................................................1-11
1-6
Chapter 2 Installation
2-1
2-2
2-3
2-4
2-5
2-6
vi
Table of Contents
Overheat LED Header............................................................................... 2-22
TPM Header/Port 80 Header.................................................................... 2-23
LAN3/LAN4 LED Indication Header.......................................................... 2-23
Power SMB (I2C) Connector..................................................................... 2-24
System Management Bus Header............................................................ 2-24
Standby Power.......................................................................................... 2-25
2-7
2-8
2-9
Chapter 3 Troubleshooting
3-1
3-2
3-3
3-4
3-5
Chapter 4 BIOS
4-1
Introduction....................................................................................................... 4-1
4-2
4-3
4-4
4-4
4-5
4-6
4-7
vii
viii
Chapter 1: Introduction
Chapter 1
Introduction
1-1 Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.
The following items are included in the retail box.
1-1
Note: All graphics shown in this manual were based upon the latest PCB Revision
available at the time of publishing of the manual. The motherboard you've received
may or may not look exactly the same as the graphics shown in this manual.
1-2
Chapter 1: Introduction
A1SAM-2550F/A1SRM-2558F Motherboard Image (Rev. 1.01)
Note: All graphics shown in this manual were based upon the latest PCB Revision
available at the time of publishing of the manual. The motherboard you've received
may or may not look exactly the same as the graphics shown in this manual.
1-3
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
USB0/1
COM1
JVGA1
JPG1
BMC
IPMI_LAN
JPK1
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
JSD1
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
I-SATA3
FAN3
JL1
JOH1
USB4/5
I-SATA5
LED3
JWD1
COM2
JPUSB1
BUZZER
JD1
FPCTRL
JBR1
JPB1
SP1
1-4
Chapter 1: Introduction
A1SAM/A1SRM Series Motherboard Quick Reference
A1SAM/A1SRM Series Motherboard Jumpers
Jumper
Description
Default
JBT1
CMOS Clear
Off (Normal)
JD1
JI2C1/JI2C2
JPG1
VGA Enable
JPL1
JPUSB1
JWD1
Description
Battery
COM1/COM2
FAN1-FAN3
JD1
JF1
JIPMB1
JL1
JOH1
JPI2C1
JPK1
JPW1
JSD1
JSTBY1
JTPM1
JUIDB1
LAN1/LAN3, LAN2/LAN4
IPMI-LAN
I-SATA0-I-SATA5
Slot4
Slot6
SP1
Internal Speaker/Buzzer
USB 4/5
USB 6
1-5
LED
Description
Color/State
Status
LED2
Green: Blinking
BMC/IPMI: Normal
LED3
Power LED
Green: On
System Power On
LED7
Blue: On
Unit Identified
LED8
1-6
Chapter 1: Introduction
Motherboard Features
CPU
Memory
Four (4) memory slots support up to 64 GB of DDR3 Unbuffered (UDIMM) ECC or Non-ECC 1600/1333 MHz (1.5V,
1.35V) memory
Note: Please populate identical memory modules (of the
same type/same speed/same frequency/same size) in all
slots.
Dual-channel or single-channel w/x8 data width singlerank/dual-rank memory
DIMM sizes
UDIMM
Expansion Slot
Network Connections
I/O Devices
SATA Connections
SATA 3.0 (6Gb/s)
USB Devices
Four (4) USB 2.0 ports on the rear I/O panel (USB 0/1,
2/3),
Two (2) USB 2.0 front accessible connector headers (USB
4/5),
One (1) USB 2.0 Type A connector (USB 6)
Serial (COM) Ports
One (1) COM Port on the rear I/O panel (COM1)
One (1) front accessible Serial port header (COM2)
VGA (Graphics Display)
One (1) VGA Port on the rear I/O panel supported by the
Aspeed AST 2400 VGA Controller
BIOS
1-7
PC Health Monitoring
CPU Monitoring
Onboard voltage monitors for 3.3V, 3.3V Standby,
+5V,+12V, VBAT, VDIMM, and VCORE for CPU
CPU/System overheat LED and control
CPU Thermal Trip support
SoC Thermal Control Circuit (TCC) mechanism
Thermal Monitor Support
Fan Control
Low noise fan speed control
System Management
CD Utilities
Other
Dimensions
A1SAM-2750F
Mothrboard Model Name
A1SAi-2750F A1SAM-2550F
A1SAi-2550F
SoC Code Name
Avoton
Avoton
Processor Number
C2750
C2550
# of Cores
8
4
# of Threads
8
4
Clock Speed
2.4 GHz
2.4 GHz
Max Turbo Frequency
2.6 GHz
2.6 GHz
Intel QuickAssist Technology
No
No
Instruction Set
64-bit
64-bit
Embedded Options Available
No
No
SoC Max TDP
20 W
14 W
# of Memory Channels
2
2
Intel Turbo Boost Technology
Yes
Yes
Intel Virtualization Technology (VT-x) Yes
Yes
AES New Instructions
Yes
Yes
Intel Hyper-Threading Technology
No
No
Intel QuickAssist Technology
No
No
1-8
A1SRM-2758F A1SRi-2558F
A1SRM-2558F
A1SRi-2758F
Rangeley
C2758
8
8
2.4 GHz
N/A
Yes
64-bit
Yes
20 W
2
No
Yes
Yes
No
Yes
Rangeley
C2558
4
4
2.4 GHz
N/A
Yes
64-bit
Yes
15 W
2
No
Yes
Yes
No
Yes
Chapter 1: Introduction
A1SAM/A1SRM Series Motherboard Block Diagram
SPI
FLASH 128Mb
USB Hub
PD720114
USB 2.0
USB 2.0
USB Hub
PD720114
USB 2.0
RTL8211E
USB 0
SATA GEN2
PCIE x 1
PEG [0]
AST2400
10BASE-T/100BASE-T/1000BASE-T
SGMII x 4
USB [2:3]
VGA
LPC
REAR
FAN x 3
TX/RX
(debug)
88E1543
LAN3
LAN1
REAR
TPM HDR
0Ohm
NI
USB 1
SATA GEN3
GbE LAN
CHB
SATA 2.0
SATA 2.0
SATA 2.0
SATA 2.0
PEG [4..7]
USB 2.0
REAR
RJ45
REAR
CHB
PCIE x 4
B1
SATA 3.0
SATA 3.0
USB
HEADER
B2
DIMMA1
JPCIE3
PEG [8..15]
CHA
DIMMB1
DIMMB2
JPCIE2
(Optional)
CHA
DIMMA2
PCIE x 8
JPCIE1
A1
A2
AVOTON SOC
LPC
UART1 UART2
COM2
COM1
REAR
1-9
LAN4
LAN2
REAR
1-10
Chapter 1: Introduction
1-11
1-12
Chapter 2: Installation
Chapter 2
Installation
2-1 Standardized Warning Statements
The following statements are industry-standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions or
experience difficulty, contact Supermicro's Technical Support department for assistance. Only certified technicians should attempt to install or configure components.
Read this section in its entirety before installing or configuring components in the
Supermicro chassis.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
2-1
!
.
.
.
!
.
.
.
Waarschuwing
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften
afgevoerd te worden.
2-2
Chapter 2: Installation
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
Warnung
Die Entsorgung dieses Produkts sollte gem allen Bestimmungen und Gesetzen
des Landes erfolgen.
Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont gnralement soumis des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprs de
l'organisme comptent.
!
.
2-3
!
.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
Precautions
Use a grounded wrist strap designed to prevent static discharge.
Touch a grounded metal object before removing the board from the antistatic
bag.
Handle the board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags when not in
use.
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the motherboard.
Use only the correct type of onboard CMOS battery. Do not install the onboard
battery upside down to avoid possible explosion.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure that the person handling it is static protected.
2-4
Chapter 2: Installation
CAUTION
DIMM Type
POR Speeds
Memory Population
Sequence
Unbuffered
DDR3 DIMM
1600,1333
A1, B1 (2 DIMMs)
Unbuffered
DDR3 DIMM
1600,1333
DIMMA1
DIMMA2
2-5
DIMMB1
DIMMB2
SoC Processor
DIMM Installation
1. Insert the desired number of DIMMs into the memory slots, starting with
DIMMA1 (Channel A, Slot 1.) For the system to work properly, please use the
memory modules of the same type and speed in the same motherboard.
Module Notch
Module Key
Socket Key
2. Push the release tabs outwards on both ends of the DIMM slot to unlock it.
3. Align the key of the DIMM module with the receptive point on the memory
slot.
4. Align the notches on both ends of the module against the receptive points on
the ends of the slot.
5. Use two thumbs together to press the notches on both ends of the module
straight down into the slot until the module snaps into place.
Side Clips
6. Press the release tabs to the lock positions to secure the DIMM module into
the slot.
2-6
Chapter 2: Installation
Note: Due to memory allocation to system devices, the amount of
memory that remains available for operational use will be reduced when
4 GB of RAM is used. The reduction in memory availability is disproportional. See the following table for details.
Possible System Memory Allocation & Availability
System Device
Size
Physical Memory
Remaining (-Available)
(4 GB Total System
Memory)
1 MB
3.99
Local APIC
4 KB
3.99
2 MB
3.99
4 KB
3.99
256 MB
3.76
256 MB
3.51
512 MB
3.01
VGA Memory
16 MB
2.85
TSEG
1 MB
2.84
2.84
2-7
Tools Needed
Philips Screwdriver
(1)
Standoffs (5)
Only if Needed
A1SAM/A1SRM Series
Rev. 1.01
2-8
Chapter 2: Installation
2. Locate the mounting holes on the motherboard. (See the previous page.)
3. Locate the matching mounting holes on the chassis. Align the mounting holes
on the motherboard against the mounting holes on the chassis.
4. Install standoffs in the chassis as needed.
5. Install the motherboard into the chassis carefully to avoid damaging other
motherboard components.
6. Using the Phillips screwdriver, insert a Phillips head #6 screw into a mounting
hole on the motherboard and its matching mounting hole on the chassis.
2-9
A1SAM/A1SRM Series
Rev. 1.01
B
Backplane I/O Panel
A. COM1
G. LAN1
H. LAN3
I. LAN2
D. IPMI LAN
J. LAN4
K. VGA
L. UID Switch
2-10
Chapter 2: Installation
Universal Serial Bus (USB)
Four Universal Serial Bus 2.0 ports (0/1, 2/3) are located on the I/O back panel.
In addition, a USB header that supports two USB 2.0 connectors (USB 4/5) and a
Type A USB 2.0 port (USB 6) are also located on the motherboard to provide front
accessible USB support. See the tables below for pin definitions.
FP USB (2.0) (4/5, USB 6)
Pin Definitions
USB4, 6
Pin # Definition
+5V
+5V
USB_PN1
USB_PN0
USB_PP1
Ground
+5V
+5V
PO-
PO-
USB_PP0
PO+
PO+
Ground
Ground
Ground
NC
5
Key
(NC= No connection)
Serial Ports
Pin # Definition
COM1
COM2
USB 5
Pin # Definition
Pin #
Definition
DCD
DSR
RXD
RTS
TXD
CTS
DTR
RI
Ground
10
N/A
2
COM2
A. Backpanel USB 0
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
B. Backpanel USB 1
USB0/1
COM1
JVGA1
C. Backpanel USB 2
JPG1
BMC
DIMMA1
DIMMA2
JPK1
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
IPMI_LAN
JLAN1
DIMMB1
DIMMB2
JLAN2
F. Type A USB 6
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
G. COM 1
JSTBY1
H. COM 2
JBAT1
LED8
JTPM1
SoC Processor
JF1
JPW1
BATTERY
I-SATA1
FAN1
FAN2
USB6
I-SATA4
I-SATA2
I-SATA0
I-SATA3
FAN3
USB4/5
I-SATA5
JL1
JOH1
JSD1
FPCTRL
JD1
JPUSB1
JWD1
COM2
BUZZER
LED3
JBR1
JPB1
SP1
JBT1
2-11
B C
A
LAN Ports
Pin Definition
Pin# Definition
P2V5SB
10
SGND
TD0+
11
Act LED
TD0-
12
P3V3SB
TD1+
13
TD1-
14
TD2+
15
Ground
TD2-
16
Ground
TD3+
17
Ground
TD3-
88
Ground
(NC: No Connection)
VGA
A VGA port is located next to the
LAN 2/4 ports on the I/O backpanel.
Use this port to connect to a compatible VGA display.
A. LAN1
B. LAN3
C. LAN2
D. LAN4
F. VGA
A1SAM/A1SRM Series
Rev. 1.01
G
2-12
A C
Chapter 2: Installation
Unit Identifier Switch
UID Switch
Pin#
Definition
Ground
Ground
Button In
Ground
UID LED
Status
Color/State OS Status
Blue: On
Windows OS
Unit Identified
Blue:
Blinking
Linux OS
Unit Identified
19
Ground
NMI
X
3.3 V
FP PWRLED
3.3V Stby
HDD LED
3.3V Stby
3.3V Stby
A1SAM/A1SRM Series
Rev. 1.01
3.3V
Ground
Reset
Reset Button
Ground
PWR
Power Button
2-13
JUIDB1
LAN1/LAN3
USB 2/3
USB0/1
COM1
JVGA1
JPG1
BMC
IPMI_LAN
JPK1
JPL1
PHY
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
JSD1
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
I-SATA3
FAN3
JL1
JOH1
USB4/5
I-SATA5
LED3
JWD1
COM2
JPUSB1
BUZZER
JD1
FPCTRL
JBR1
JPB1
SP1
19
Ground
NMI
X
3.3 V
FP PWRLED
3.3V Stby
HDD LED
NIC1 Link LED
3.3V Stby
3.3V Stby
3.3V
Ground
Ground
2
2-14
Reset
Reset Button
PWR
Power Button
Chapter 2: Installation
NMI Button
Pin Definitions (JF1)
Power LED
Pin#
Definition
19
Control
20
Ground
Power LED
Pin Definitions (JF1)
Pin#
Definition
15
3.3V
16
PWR LED
A. NMI Button
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB0/1
USB 2/3
B. PWR LED
COM1
JVGA1
JPG1
BMC
IPMI_LAN
JPK1
20
JPL1
PHY
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
Rev. 1.01
BIOS
19
Ground
A1SAM/A1SRM Series
NMI
PWRI2C
JPI2C1
X
3.3 V
FP PWRLED
JSTBY1
3.3V Stby
HDD LED
JBAT1
LED8
JTPM1
JBT1
JF1
I-SATA1
FAN1
FAN2
USB6
I-SATA4
I-SATA2
I-SATA0
FAN3
1
I-SATA3
I-SATA5
LED3
JL1
JOH1
USB4/5
JSD1
FPCTRL
JPUSB1
JWD1
COM2
JD1
JBR1
JPB1
BUZZER
3.3V Stby
JPW1
BATTERY
SP1
3.3V Stby
SoC Processor
3.3V
Ground
Reset
Reset Button
Ground
PWR
Power Button
2-15
HDD LED
Pin Definitions (JF1)
NIC1/NIC2 (LAN1/LAN2)
Pin#
Definition
13
3.3V Standby
14
HD LED
LAN1/LAN2 LED
Pin Definitions (JF1)
The NIC (Network Interface Controller) LED connection for LAN port 1
is located on pins 11 and 12 of JF1,
and the LED connection for LAN Port
2 is on Pins 9 and 10. NIC1 LED and
NIC2 LED are 2-pin NIC LED headers. Attach NIC LED cables to NIC1
and NIC2 LED indicators to display
network activities. Refer to the table
on the right for pin definitions.
Pin#
Definition
9/11
3.3V Standby
10/12
JUIDB1
LAN1/LAN3
A. HDD LED
USB0/1
USB 2/3
COM1
JVGA1
JPG1
BMC
D
JPK1
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
IPMI_LAN
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
20
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
JTPM1
LED8
JBT1
3.3V Stby
3.3V Stby
3.3V Stby
UID LED Cathode
I-SATA1
FAN1
FAN2
USB6
I-SATA0
I-SATA4
I-SATA2
FAN3
1
I-SATA3
I-SATA5
LED3
JL1
JOH1
USB4/5
A HDD LED
JSD1
FPCTRL
JPUSB1
JWD1
COM2
JD1
JBR1
JPB1
BUZZER
X
3.3 V
FP PWRLED
JPW1
BATTERY
SP1
NMI
SoC Processor
JF1
19
Ground
3.3V
Ground
Reset
Reset Button
Ground
PWR
Power Button
2-16
Chapter 2: Installation
Overheat (OH)/Fan Fail/PWR Fail/
UID LED
Pin#
Blue_UID LED
Definition
Pin#
Definition
3.3V
JUIDB1
LAN1/LAN3
USB 2/3
Fail LED
USB0/1
COM1
JVGA1
JPG1
C. PWR Fail
BMC
IPMI_LAN
JPK1
20
Rev. 1.01
PWRI2C
JPI2C1
JSTBY1
SoC Processor
LED8
JTPM1
JBT1
JPW1
LED3
3.3V Stby
I-SATA1
FAN1
FAN2
USB6
I-SATA4
I-SATA2
I-SATA0
FAN3
JL1
JOH1
I-SATA3
I-SATA5
JSD1
FPCTRL
JPUSB1
JWD1
USB4/5
3.3V Stby
JD1
JBR1
JPB1
BUZZER
COM2
3.3V Stby
HDD LED
NIC1 Link LED
BATTERY
SP1
X
3.3 V
FP PWRLED
JBAT1
JF1
NMI
A1SAM/A1SRM Series
BIOS
19
Ground
JPL1
PHY
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
3.3V
Ground
Reset
Reset Button
Ground
PWR
Power Button
2-17
Reset Button
Pin Definitions (JF1)
Power Button
LAN2/LAN4
LAN1/LAN3
USB0/1
USB 2/3
LED7
JPG1
Signal
+3V Standby
20
19
JPL1
NMI
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
LED8
JTPM1
SoC Processor
X
3.3 V
FP PWRLED
3.3V Stby
HDD LED
3.3V Stby
3.3V Stby
JBT1
JPW1
JD1
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
JL1
JOH1
FAN3
JWD1
I-SATA3
I-SATA5
JPUSB1
LED3
JSD1
FPCTRL
JBR1
JPB1
Definition
Ground
A1SAM/A1SRM Series
USB4/5
Pin#
DIMMA1
DIMMA2
JPK1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
BATTERY
COM2
Ground
IPMI_LAN
JLAN1
DIMMB1
DIMMB2
JLAN2
JBAT1
SP1
B. PWR Button
BMC
BUZZER
Reset
A. Reset Button
COM1
JVGA1
JF1
Definition
Power Button
Pin Definitions (JF1)
JUIDB1
Pin#
3.3V
Reset
Reset Button
Ground
PWR
B
Power Button
2-18
Ground
Chapter 2: Installation
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
Pin#
Definition
13
+3.3V
+3.3V
14
-12V
+3.3V
15
COM
COM
16
PS_ON
+5V
17
COM
COM
18
COM
+5V
19
COM
COM
20
Res (NC)
PWR_OK
21
+5V
5VSB
22
+5V
10
+12V
23
+5V
11
+12V
24
COM
12
+3.3V
USB0/1
JPG1
BMC
IPMI_LAN
JPK1
JPL1
PHY
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
JSD1
2-19
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
I-SATA3
JL1
JOH1
FAN3
JWD1
USB4/5
I-SATA5
LED3
JPUSB1
BUZZER
COM2
JD1
FPCTRL
JBR1
JPB1
SP1
Definition
COM1
JVGA1
Pin #
Fan Header
Pin Definitions
LAN2/LAN4
LAN1/LAN3
USB 2/3
LED7
IPMI_LAN
JPL1
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
LED8
JTPM1
SoC Processor
JBT1
JPW1
JD1
2-20
A
FAN1
FAN2
I-SATA0
B
USB6
I-SATA1
I-SATA4
I-SATA2
JL1
JOH1
FAN3
JWD1
USB4/5
I-SATA3
I-SATA5
JPUSB1
LED3
JSD1
FPCTRL
JBR1
JPB1
Tachometer
PWM_Control
Pin#
Definition
Intrusion Input
Ground
D. Chassis Intrusion
DIMMA1
DIMMA2
JPK1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
DIMMB1
DIMMB2
JLAN1
BATTERY
COM2
2.5A/+12V
(Red)
C. Fan 3
JPG1
JLAN2
JBAT1
SP1
B. Fan 2
COM1
BMC
BUZZER
Ground (Black)
A. Fan 1
USB0/1
JVGA1
JF1
Definition
Chassis Intrusion
Pin Definitions (JL1)
JUIDB1
Pin#
Chapter 2: Installation
Internal Buzzer (SP1)
Internal Buzzer
Pin Definition
Pin#
Pin 1
Pos. (+)
Beep In
Pin 2
Neg. (-)
Alarm
Speaker
Definitions
Power LED/Speaker
On JD1 header, pins 1-3 are used for
power LED indication, and pins 4-7
are for the speaker. Connect pins 4-7
of JD1 with a cable to use the external speaker. If you wish to use the
onboard speaker, close pins 6-7 with
a jumper (Default). See the tables on
the right for pin definitions.
LAN2/LAN4
LED7
JUIDB1
Pin Setting
Anode (+)
Pin2
Cathode (-)
Pin3
NA
Speaker Connector
Pin Settings
Pin Setting
LAN1/LAN3
USB 2/3
External Speaker
Pins 6-7
A. Internal Buzzer
COM1
JPG1
B.
DIMMA1
DIMMA2
JPK1
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JPW1
JSD1
2-21
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
FAN3
1
I-SATA3
I-SATA5
LED3
JL1
JOH1
USB4/5
JD1
FPCTRL
JPUSB1
JWD1
COM2
JTPM1
LED8
JBR1
JPB1
SP1
BUZZER
SoC Processor
JBT1
JF1
PWR
LED/
Speaker Header
IPMI_LAN
JLAN1
DIMMB1
DIMMB2
JLAN2
JBAT1
Definition
Pins 4-7
USB0/1
JVGA1
BMC
BATTERY
Definition
Pin 1
DOM PWR
Pin Definitions
Pin#
Definition
5V
Ground
Ground
Overheat LED
Pin Definitions
Pin
5vDC
OH Active
LAN2/LAN4
LED7
JUIDB1
Definition
LAN1/LAN3
USB 2/3
State
Definition
Off
Normal
Solid
Overheat
Flashing
Fan Fail
USB0/1
A. DOM PWR
COM1
JVGA1
JPG1
BMC
IPMI_LAN
JPK1
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
2-22
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
I-SATA3
FAN3
JL1
JOH1
USB4/5
I-SATA5
LED3
JWD1
JSD1
FPCTRL
JPUSB1
BUZZER
COM2
JD1
JBR1
JPB1
SP1
JPW1
BATTERY
Chapter 2: Installation
TPM Header/Port 80 Header
TPM/Port 80 Header
Pin Definitions
Pin #
Definition
Pin #
Definition
LCLK
GND
LFRAME#
<(KEY)>
LRESET#
+5V (X)
LAD 3
LAD 2
+3.3V
10
LAD1
11
LAD0
12
GND
13
SMB_CLK4
14
SMB_DAT4
15
+3V_DUAL
16
SERIRQ
17
GND
18
CLKRUN# (X)
19
LPCPD#
20
LDRQ# (X)
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
USB0/1
A. TPM/Port 80
COM1
JVGA1
JPG1
B
JPK1
tion Header
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
IPMI_LAN
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
A
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
JSD1
2-23
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
I-SATA3
FAN3
JL1
JOH1
USB4/5
I-SATA5
LED3
JPUSB1
JWD1
COM2
JD1
FPCTRL
JBR1
JPB1
SP1
BUZZER
PWR SMB
Pin Definitions
Pin#
Definition
Clock
Data
PWR Fail
Ground
+3.3V
SMBus Header
Pin Definitions
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
Pin#
Definition
Data
Ground
Clock
No Connection
USB0/1
A. PWR SMBus
COM1
JVGA1
JPG1
BMC
DIMMA1
DIMMA2
LAN3/4 LED
JPL1
LED2
JIPMB1
PHY
JPK1
JI2C2
JI2C1
IPMI_LAN
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
JSD1
2-24
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
I-SATA3
FAN3
JL1
JOH1
USB4/5
I-SATA5
LED3
JPUSB1
JWD1
COM2
JD1
FPCTRL
JBR1
JPB1
SP1
BUZZER
Chapter 2: Installation
Standby Power
Standby Power
Pin Definitions
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
Pin#
USB0/1
JPG1
BMC
IPMI_LAN
JPK1
JPL1
PHY
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
JSD1
2-25
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
I-SATA3
FAN3
JL1
JOH1
USB4/5
I-SATA5
LED3
JPUSB1
JWD1
COM2
JD1
FPCTRL
JBR1
JPB1
SP1
BUZZER
+5V Standby
Ground
Wake-up
A. 5V Standby PWR
COM1
JVGA1
Definition
GLAN Enable
Jumper Settings
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
COM1
IPMI_LAN
JPK1
JI2C2
JI2C1
JPL1
LED2
JIPMB1
LAN3/4 LED
PHY
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
2-26
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
FAN3
1
I-SATA3
I-SATA5
LED3
JL1
JOH1
USB4/5
JSD1
FPCTRL
JPUSB1
JWD1
COM2
JD1
JBR1
JPB1
SP1
BUZZER
Enabled (default)
2-3
Disabled
Disable
JPG1
BMC
Definition
1-2
USB0/1
JVGA1
Pin#
Chapter 2: Installation
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads
to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such
as a small screwdriver to touch both pads at the same time to short the connection. Always remove the AC power cord from the system before clearing CMOS.
Note 1: For an ATX power supply, you must completely shut down the
system, remove the AC power cord, and then short JBT1 to clear CMOS.
Note 2: Be sure to remove the onboard CMOS Battery before you short
JBT1 to clear CMOS.
Note 3: Clearing CMOS will also clear all passwords.
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
Jumper Setting
Enabled
Pins 2-3
Disabled
(Default)
A. Clear CMOS
USB0/1
COM1
JVGA1
B. JI2C1
JPG1
BMC
JPK1
JPL1
LED2
JIPMB1
PHY
DIMMA1
DIMMA2
LAN3/4 LED
C. JI2C2
IPMI_LAN
JLAN1
DIMMB1
DIMMB2
JI2C2
JI2C1
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
2-27
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
FAN3
1
I-SATA3
I-SATA5
LED3
JL1
JOH1
USB4/5
JSD1
FPCTRL
JPUSB1
JWD1
COM2
JD1
JBR1
JPB1
SP1
BUZZER
Definition
Pins 1-2
Watch Dog
Jumper Settings
ware application hangs. Close pins 1-2 to reset the system if an application hangs. Close
pins 2-3 to generate a non-maskable interrupt
signal for the application that hangs. See the
table on the right for jumper settings. Watch
Dog must also be enabled in the BIOS.
Jumper Setting
Reset (default)
Pins 2-3
NMI
Open
Disabled
VGA Enable
VGA Enable
Jumper Settings
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
Jumper Setting
Enabled (Default)
Pins 2-3
Disabled
B. VGA Enable
JPG1
BMC
IPMI_LAN
JPK1
JPL1
PHY
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
2-28
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
FAN3
1
I-SATA3
I-SATA5
LED3
USB4/5
JSD1
FPCTRL
JPUSB1
COM2
JL1
JOH1
JWD1
JD1
JBR1
JPB1
SP1
BUZZER
Definition
Pins 1-2
USB0/1
JVGA1
Definition
Pins 1-2
Chapter 2: Installation
Jumper Setting
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
Pins 2-3
Normal (Default)
USB0/1
COM1
JVGA1
able
JPG1
BMC
IPMI_LAN
JPK1
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
JSD1
2-29
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
FAN3
1
I-SATA3
I-SATA5
JL1
JOH1
USB4/5
JD1
LED3
JPUSB1
JWD1
COM2
FPCTRL
JBR1
JPB1
SP1
BUZZER
Definition
Pins 1-2
GLAN LEDs
There are four GLAN ports on the motherboard. Each Gigabit Ethernet LAN port
has two LEDs. The Yellow LED on the
right indicates connection and activity.
The Link LED on the left side may be
green, amber or off to indicate the speed
of the connection. See the tables at right
for more information.
Status
Off
No Connections
Yellow
Flashing
Active
Definition
Off
Amber
1 Gbps
Green
10 Gbps
LAN 1/LAN 2
IPMI LAN
In addition to LAN ports, an IPMI Dedicated LAN is also located on the I/O Backplane of the motherboard. The amber
LED on the right indicates activity, while
the green LED on the left indicates the
speed of the connection. See the tables
at right for more information.
LAN2/LAN4
LAN1/LAN3
USB 2/3
IPMI LAN
(X8ST3-F)
BMC: Normal
LED7
A. LAN LEDs
USB0/1
JPG1
IPMI_LAN
DIMMA1
DIMMA2
JPK1
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
DIMMB1
DIMMB2
JLAN1
PHY
Definition
Green:Blinking
COM1
JLAN2
Activity LED
JVGA1
BMC
Definition
JUIDB1
Activity LED
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
FAN1
FAN2
I-SATA0
B
USB6
I-SATA1
I-SATA4
I-SATA2
FAN3
1
I-SATA3
I-SATA5
LED3
JL1
JOH1
USB4/5
JSD1
FPCTRL
JPUSB1
JWD1
COM2
JD1
JBR1
JPB1
SP1
BUZZER
2-30
Chapter 2: Installation
Onboard Power LED
LED Color
Definition
Off
Green
System On
Green:
Flashing
Quickly
ACPI S1 State
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
Color/State
Definition
Solid
Overheat
Blinking
USB0/1
A. PWR LED
COM1
JVGA1
JPG1
BMC
IPMI_LAN
JPK1
LED
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
DIMMA1
DIMMA2
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
SoC Processor
LED8
JTPM1
JBT1
JF1
JPW1
BATTERY
JSD1
2-31
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
FAN3
JL1
JOH1
I-SATA3
I-SATA5
JWD1
USB4/5
JD1
JPUSB1
BUZZER
COM2
LED3
JBR1
JPB1
FPCTRL
SP1
Color/State OS Status
Blue: On
Windows OS
Unit Identified
Blue:
Blinking
Linux OS
Unit Identified
Color/State
Definition
Green:
Blinking
BMC/IPMI Normal
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
A. UID LED
USB0/1
B. BMC/IPMI Heart-
COM1
JVGA1
JPG1
beat LED
BMC
JPL1
LED2
JIPMB1
PHY
DIMMA1
DIMMA2
LAN3/4 LED
JPK1
JI2C2
JI2C1
IPMI_LAN
JLAN1
DIMMB1
DIMMB2
JLAN2
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
JPW1
BATTERY
2-32
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
FAN3
1
I-SATA3
I-SATA5
LED3
JL1
JOH1
USB4/5
JSD1
FPCTRL
JPUSB1
JWD1
COM2
JD1
JBR1
JPB1
SP1
BUZZER
Chapter 2: Installation
LAN2/LAN4
LED7
JUIDB1
LAN1/LAN3
USB 2/3
Serial ATA
Pin Definitions
Pin#
Definition
Ground
TX_P
TX_N
Ground
RX_N
RX_P
Ground
A. I-SATA 3.0 #0
USB0/1
COM1
JVGA1
B. I-SATA 3.0 #1
JPG1
BMC
DIMMA1
DIMMA2
JPK1
D. I-SATA 2.0 #3
E. I-SATA 2.0 #4
JPL1
LED2
JIPMB1
JI2C2
JI2C1
LAN3/4 LED
PHY
C. I-SATA 2.0 #2
IPMI_LAN
JLAN1
DIMMB1
DIMMB2
JLAN2
F. I-SATA 2.0 #5
A1SAM/A1SRM Series
Rev. 1.01
BIOS
PWRI2C
JPI2C1
JSTBY1
JBAT1
LED8
JTPM1
SoC Processor
JBT1
JF1
E C A
2-33
FAN1
FAN2
I-SATA0
USB6
I-SATA1
I-SATA4
I-SATA2
FAN3
JL1
JOH1
I-SATA3
I-SATA5
LED3
JWD1
USB4/5
DB
JSD1
FPCTRL
JPUSB1
BUZZER
COM2
JD1
JBR1
JPB1
SP1
JPW1
BATTERY
Notes
2-34
Chapter 3: Troubleshooting
Chapter 3
Troubleshooting
3-1 Troubleshooting Procedures
Use the following procedures to troubleshoot your system. If you have followed all
of the procedures below and still need assistance, refer to the Technical Support
Procedures and/or Returning Merchandise for Service section(s) in this chapter.
Always disconnect the AC power cord before adding, changing or installing any
hardware components.
Before Power On
1. Make sure that the Standby PWR LED is not on. (Note: If it is on, the onboard
power is on. Be sure to unplug the power cable before installing or removing
the components.)
2. Make sure that there are no short circuits between the motherboard and chassis.
3. Disconnect all ribbon/wire cables from the motherboard, including those for the
keyboard and mouse. Also, be sure to remove all add-on cards.
No Power
1. Make sure that there are no short circuits between the motherboard and chassis.
2. Make sure that all jumpers are set to their default positions.
3. Check if the 115V/230V switch on the power supply is properly set.
4. Turn the power switch on and off to test the system.
5. The battery on your motherboard may be old. Check to make sure that it still
supplies ~3VDC. If it does not, replace it with a new one.
No Video
1. If the power is on, but you have no video, you will need to remove all the addon cards and cables first.
3-1
3-2
Chapter 3: Troubleshooting
2. BIOS upgrades can be downloaded from our website at (http://www.supermicro.
com/support/bios/).
Note: Not all BIOS can be flashed. Some cannot be flashed; it depends
on the boot block code of the BIOS.
3. If you've followed the instructions above to troubleshoot your system, and still
cannot resolve the problem, then contact Supermicro's technical support and
provide them with the following information:
System configuration
An example of a Technical Support form is on our website at (http://www.supermicro.com/support/rma/rma.cfm).
3-3
3-4
Chapter 3: Troubleshooting
Battery Installation
1. To install an onboard battery, follow the steps 1 & 2 above and continue
below:
2. Identify the battery's polarity. The positive (+) side should be facing up.
3. Insert the battery into the battery holder and push it down until you hear a
click to ensure that the battery is securely locked.
Warning: When replacing a battery, be sure to only replace it with the same type.
OR
3-5
3-6
Chapter 4
BIOS
4-1 Introduction
This chapter describes the AMI BIOS setup utility for the A1SAM/A1SRM Series
Motherboard. The ROM BIOS is stored in a Flash EEPROM and can be easily
updated. This chapter describes the basic navigation of the AMI BIOS setup utility
setup screens.
Note: For AMI BIOS Recovery, please refer to the UEFI BIOS Recovery
Instructions in Appendix C.
4-1
4-2
4-3
Warning: Take Caution when changing the Advanced settings. An incorrect value, a
very high DRAM frequency, or an incorrect DRAM timing setting may make the system
unstable. When this occurs, revert to the setting to its manufacture default setting.
Boot
Feature
Boot Configuration
Quiet Boot
This feature selects the screen display between POST messages or the OEM
logo at bootup. Select Disabled to display the POST messages. Select Enabled
to display the OEM logo instead of the normal POST messages. The options are
Enabled and Disabled.
AddOn ROM Display Mode
This feature sets the display mode for the Option ROM. Select Keep Current to
use the current AddOn ROM display setting. Select Force BIOS to use the Option
ROM display mode set by the system BIOS. The options are Force BIOS and
Keep Current.
Bootup Num-Lock
This feature selects the Power-on state for the Numlock key. The options are Off
and On.
4-4
Power Configuration
Watch Dog Function
If enabled, the Watch Dog timer will allow the system to reboot when it is inactive
for more than 5 minutes. The options are Enabled and Disabled.
Power Button Function
This feature controls how the system shuts down when the power button is pressed.
Select 4_Seconds_Override for the user to power off the system after pressing and
holding the power button for 4 seconds or longer. Select Instant Off to instantly
power off the system as soon as the user presses the power button. The options
are 4 Seconds Override and Instant Off.
Restore on AC Power Loss
Use this feature to set the power state after a power outage. Select Power-Off for
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last power state before a power loss. The options are Power-On,
Stay-Off and Last State.
SATA
Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence
of the SATA Devices and displays the following items:
SATA 3 Controller
SATA Controller
This feature enables or disables the SATA Controller specified by the user. The
options are Enabled and Disabled.
4-5
Model Name
SATA Port0/Port1
Select Enabled to enable a SATA port selected by the user. The options are
Enabled and Disabled.
Spin Up
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization sequence to the device installed on a SATA port specified
by the user. The options are Enabled and Disabled.
External Device
Select Enabled for the SATA port specified by the user to support an external
device. The options are Enabled and Disabled.
Hot Plug
Select Enabled to enable hot-plugging support on a SATA drive specified by the
user, which will allow the user to replace the SATA disk drive without shutting
down the system. The options are Enabled and Disabled.
4-6
Model Name
SATA Port 2/SATA Port 3/SATA Port 4//SATA Port 5
Select Enabled to enable a SATA port selected by the user. The options are
Enabled and Disabled.
Spin Up
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization sequence to the device installed on a SATA port specified
by the user. The options are Enabled and Disabled.
External Device
Select Enabled for the SATA port specified by the user to support an external
device. The options are Enabled and Disabled.
Hot Plug
Select Enabled to enable hot-plugging support on a SATA drive specified by the
user, which will allow the user to replace the SATA disk drive without shutting
down the system. The options are Enabled and Disabled.
CPU
Configuration
Processor ID
4-7
Processor Frequency
Microcode Revision
L1 Cache RAM
L2 L1 Cache RAM
Processor Version
Clock Spread Spectrum
If this feature is set to Enabled, the BIOS will monitor the level of Electromagnetic
Interference caused by the components and will attempt to reduce the interference
when needed. The options are Enabled and Disabled.
EIST (GV3)
EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically
adjust processor voltage and core frequency in an effort to reduce power consumption and heat dissipation. The options are Disabled, Enabled, and Auto.
P-State Coordination
This feature selects the type of coordination for the P-State of the processor. P-State
is a processor operational state that reduces the processor's voltage and frequency.
This makes the processor more energy efficient, resulting in further energy gains.
The options are Hardware, Package, and Module.
TM1 (Available when supported by the CPU.)
Select Enabled to activate CPU's internal thermal monitor mechanism which will
allow the CPU to regulate its power consumption based on the modulation of its
internal clock when the CPU temperature reaches a pre-defined overheat threshold.
The options are Disabled and Enabled.
TM2 Mode (Available when the item above-TM1 is Enabled)
This feature is used to set the TM2 mode. The options are LFM Throttling, and
Adaptive Throttling.
CPU C State
The CPU C-State architecture is a processor power management platform developed by Intel to reduce power consumption by blocking clock cycles to the CPU
during C1 State (Halt State). Select Enabled for CPU C-Sates support. The options
are Auto, Enabled, and Disabled.
4-8
4-9
Configuration
Warning! Setting the wrong values in the following sections may cause the system
to malfunction.
System
Memory Information
The following memory information will be displayed:
MRC Version
Total Memory
Memory Frequency
ECC Support
Memory Frequency
This feature sets the memory frequency for DIMM modules installed on the motherboard. The options are Auto, DDR3-1333 (MHz), and DDR3-1600 (MHz).
CKE Power Down
Select Enabled for the BIOS to control the low power mode for the RAM during
active power standby mode. The options are Enabled and Disabled.
4-10
Fabric
4-11
Settings
ACPI Settings
High Precision Timer
Select Enabled to activate the High Precision Event Timer (HPET) that produces
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does in
synchronizing multimedia streams, providing smooth playback and reducing the dependency on other timestamp calculation devices, such as an x86 RDTSC Instruction embedded in the CPU. The High Performance Event Timer is used to replace
the 8254 Programmable Interval Timer. The options are Enabled and Disabled.
WHEA Support
Select Enables to enable WHEA (Windows Hardware Error Architecture) support for
the Windows 2008 operating system (and later versions). The options are Enabled
and Disabled.
4-12
IO Configuration
Configuration/COM2 Configuration
Serial Port
Select Enabled to enable the onboard serial port specified by the user. The options are Enabled and Disabled. If the serial port selected by the user is enabled,
the following items will be displayed.
Device Settings (For Serial Port 1 / Serial Port 2)
This item displays the device setting for a serial port selected by the user.
Change Settings (For Serial Port 1 / Serial Port 2)
This option specifies the base I/O port address and the Interrupt Request address of Serial Port 1 and 2. Select Auto to let the BIOS automatically assign
the base I/O and IRQ address.
The options for Serial Port 1 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4,
5, 6, 7, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12), (IO=3E8h; IRQ=3,
4, 5, 6, 7, 10, 11, 12) and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12).
The options for Serial Port 2 are Auto, (IO=2F8h; IRQ=3), (IO=3F8h; IRQ=3, 4,
5, 6, 7, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12), (IO=3E8h; IRQ=3,
4, 5, 6, 7, 10, 11, 12) and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 10, 11, 12).
Serial Port 2 Attribute
Use this feature to select the attribute for serial port 2. The options are SOL
(Serial On LAN), and COM.
4-13
4-14
4-15
This feature allows the user to specify how the host computer will exchange
data with the client computer, which is the remote computer used by the user.
Out-of-Band Management Port
The feature selects a serial port used by the Microsoft Windows Emergency
Management Services (EMS) to communicate with a remote server. The options
are COM1 and COM2/SOL.
Terminal Type
This feature allows the user to select the target terminal emulation type for console redirection. Select VT100 to use the ASCII character set. Select VT100+
to add color and function key support. Select ANSI to use the extended ASCII
character set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters
into one or more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Bits Per Second
This item sets the transmission speed for a serial port used in console redirection. Make sure that the same speed is used in the host computer and the client
computer. A lower transmission speed may be required for long and busy lines.
The options are 9600, 19200, 57600, and 115200 (bits per second).
Flow Control
This feature allows the user to set the flow control for Console Redirection to
prevent data loss caused by buffer overflow. Send a "Stop" signal to stop sending data when the receiving buffer is full. Send a "Start" signal to start sending
data when the receiving buffer is empty. The options are None, Hardware RTS/
CTS, and Software Xon/Xoff.
The following items will also be displayed:
Data Bits, Parity, Stop Bits
The status of each item above is displayed.
Trusted
4-16
Configuration
This feature allows the user to set the PCI/PnP configurations for the following items:
VGA Palette Snoop
Select Enabled to support VGA palette register snooping which will allow the
PCI cards that do not contain their own VGA color palette to examine the video
cards palette and mimic it for proper color display. The options are Disabled,
and Enabled.
PERR# Generation
Select Enabled to allow a PCI device to generate a PERR number for a PCI Bus
Signal Error Event. The options are Disabled and Enabled.
SERR# Generation
Select Enabled to allow a PCI device to generate an SERR number for a PCI Bus
Signal Error Event. The options are Enabled and Disabled.
4-17
4-18
4-19
4-20
4-21
Change
Enabling/Disabling Options
SMBIOS Event Log
Select Enabled to enable all features of the SMBIOS Event Logging upon the next
system boot. The options are Enabled and Disabled.
System Error Logging
Select Enabled to enable system error logging, which will allow the BIOS to log
system errors upon the next system boot . The options are Enabled and Disabled.
Erasing Settings
Erase Event Log
If No is selected, data stored in the event log will not be erased. Select Yes, Next
Reset, data in the event log will be erased upon next system reboot. Select Yes,
Every Reset, data in the event log will be erased upon every system reboot. The
options are No, Yes, Next reset, and Yes, Every reset.
When Log is Full
Select Erase Immediately for all messages to be automatically erased from the
event log when the event log memory is full. The options are Do Nothing and
Erase Immediately.
4-22
Date
Time
Error Code
Severity
4-23
Administrator Password
Use this feature to set the Administrator Password which is required to enter the
BIOS setup utility. The length of the password should be from 3 characters to 8
characters long.
User Password
Use this feature to set a User Password which is required to log into the system
and to enter the BIOS setup utility. The length of the password should be from 3
characters to 8 characters long.
Secure Boot Menu
4-24
This submenu allows the user to configure the following Key Management settings.
Default Key Provision
Select Enabled to install the default Secure-Boot keys set by the manufacturer. The
options are Disabled and Enabled.
4-25
Delete DB
Select Yes to delete the database of "Authorized Signatures" from the manufacturer's defaults. Select No to load the DB from a file. The options are Yes and No.
Set New DB
Select Yes to load the DB database from the manufacturer's defaults. Select No to
load the DB from a file. The options are Yes and No.
Append DB
Select Yes to add the DB database from the manufacturer's defaults to the existing
DB. Select No to load the DB from a file. The options are Yes and No.
Authorized Timestamps (DBT)
Delete DBT
Select Yes to delete the database of "Authorized Timestamps" (DBT) from the manufacturer's defaults. Select No to load the DB from a file. The options are Yes and No.
Append DBT
Select Yes to add the DBT database from the manufacturer's defaults to the existing
DB. Select No to load the DB from a file. The options are Yes and No
Forbiden Signature Database (DBX)
Append DBX
Select Yes to add the DBX from the manufacturer's defaults to the existing DBX.
Select No to load the DBX from a file. The options are Yes and No.
HDD Security Configuration
This item displays the HDD security setting status.
P0: INTEL SS0SC2.
4-26
This submenu allows the user to prioritize the sequence of bootable devices for
the system to boot from.
Boot Order #1
Boot Order #2
Boot Order #3
Boot Order #4
Boot Order #5
Boot Order #6
Boot Order #7
Boot Order #8
Delete Boot Option
Use this feature to remove a pre-defined boot device from which the system will
boot during startup.
Delete Boot Option
Select a bootable device to remove it from the boot device list so that the system
can no longer boot from this device.
4-27
Boot Order #1
Boot Order #1
Boot Order #1
4-28
4-29
4-30
Appendix A
BIOS Error Beep Codes
During the POST (Power-On Self-Test) routines, which are performed each time
the system is powered on, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue
with bootup. The error messages normally appear on the screen.
Fatal errors will not allow the system to continue to bootup. If a fatal error occurs, you should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps.
The numbers on the fatal error list correspond to the number of beeps for the
corresponding error.
Error Message
Description
1 beep
Refresh
Memory error
5 short beeps
Display memory
read/write error
OH LED On
System OH
System Overheat
A-1
Notes
A-2
Appendix B
Software Installation Instructions
B-1
B-2
Appendix C
UEFI BIOS Recovery Instructions
Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall
Supermicro be liable for direct, indirect, special, incidental, or consequential damages
arising from a BIOS update. If you need to update the BIOS, do not shut down or reset
the system while the BIOS is updating to avoid possible boot failure.
C-1
5. When the screen as shown above displays, using the arrow key, select the
item- "Proceed with flash update" and press the <Enter> key. You will see the
progress of BIOS Recovery as shown in the screen below.
Note: Do not interrupt the process of BIOS flashing until it is completed.
C-2
6. After the process of BIOS Recovery is complete, press any key to reboot the
system.
7. Using a different system, extract the BIOS package into a bootable USB flash
drive.
8. When a DOS prompt appears, enter AMI.BAT BIOSname.### at the prompt.
Note: Do not interrupt this process until BIOS flashing is completed.
C-3
C-4
(Disclaimer Continued)
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.