Beruflich Dokumente
Kultur Dokumente
BNG TRA M LI LG
MY RA BT, MY GIT, MY SY, T LNH SIDE BY SIDE
M LI MY RA BT
LG dishwasher
1E ( Water inlet problem >Condition : Not reached to the normal water level in spite
of 10 minute water supply ) Possible Cause: Water supply problem. The inlet hose is
kinked. The water pressure is to low (10psi) Inlet valve. The inlet water valve filter is
clogged. The hall sensor. The impeller of Air guide is bound. Remedy : Check
resistance of inlet valve ( 950-1300ohms) Clean valve. Check pressure. Replace the
Air braker.
OE ( Drain error > Condition: The drain hose kinked or blocked. Wiring connections.
The drain outlet of sump is blocked. The drain pump/motor or circuit is troubled.
Remedy: Remove kink. Check wiring. Measure the resistance of drain motor (2040ohms) Replace the drain motor or repair the circuit.
E1 (Leakage error > Conditon: Excessive RPM of washing motor happened during
wash cycle due to water leakage. Possible cause: Water leakage in hose
connections,water is leaked by damages. The motor water seal leakage of sump
assembly. The height of drain hose connection ( sink drain hose ) is not over 20".
Impeller of the washing pump is worn away. Remedy : Replace the connections of
hose. Check the point of damages and repair or replace the related parts. Correct drain
connections. Replace the impeller of the washing pump.
FE ( Excess Error > Condition : Exceesive water is supplied than normal water level
(automatically drain pump operated. Possible cause: The inlet valve is troubled,or the
controller. Remedy : Replace valve or the controller.
bE (Thermal error) Condition: the resistance of the thermistor not normally out put.
Possible cause the inlet water temperature is very high(over 194f) Wiring connections.
Thermistor problem. Remedy : Check temps to dishwasher 120 degress needed.
Check thermistor 11-14kohms at 77 degress f. Replace the PCB.
LE ( Motor error ) Condition : The motor is working abnormally. Possible cause :
Wiring connections. The impeller of washing pump is locked. The rotor of washing
motor is locked. The blade is locked. Remedy : Correct wiring connections. Replace
the cause of resrtiction. Replace the washing motor. Replace the PCB.
M LI MY GIT CA TRC
LG front load washer (fault codes)
IE (water inlet error) Cause : Correct water level (246) is not reached within 8 minutes
after water is supplied or it does not reach the preset wate r level within 25 minutes
UE (imbalance error) Cause : The load is to small, the appliance is tilted, laundry is
gathered to one side, non distributed things are put into the drum. OE (drain error)
Cause: not fully drained within 10 minutes
FE (over flow error) Cause: water is overflowing (water level frequency is over 213)
When
FE is diplayed the drain will pump out automatically.
PE (pressure sensor error) Cause: the sensor switch assembly is out of order.
dE (door open error) Cause: door not all the way closed, loose electrical connections
at door switch and pwb assembly.The door switch assembly is out of order. Gasket on
door maybe creased in.
[-E (heating error) Cause: the thermistor is out of order.
CE (oven current error) Cause: Main PWB assembly is out of order, Winding in the
stator
assembly is short circuited.
LE (locked motor error) Cause: The connector (3-pin), male,white) in the motor
harness is not connected to the connector. (3-pin,female,white) of stator assembly. Or
the electrical contact between the connectors. (3-pin,male,white) in the motor harness
and 4-pin,female,white connector in the main PWB assembly is bad or unstable. Or
the motor harness between the stator assembly and main PWB assembly is cut (open
circuit) Or the hall sensor is out of order/defective.
bE (ball sensor error) Cause : Loose ball sensor connector,ball is out of order. This is
displayed only when the start / pause button is first pressed in the OC test mode.
EE (EEprom error) Cause: EEprom is out order. Displayed only when the start / pause
button is first pressed in the OC test mode.
PF (power failure) Cause : the washer experienced a power failure)