Beruflich Dokumente
Kultur Dokumente
GUIDE QUESTIONNAIRES
for seafarers
The Annual Publication of Database of Questionnaires is mandated in Republic Act
10635 or the Act Establishing the Maritime Industry Authority (MARINA) as the Single
Maritime Administration Responsible for the Implementation and Enforcement of
the 1978 International Convention on Standards of Training, Certification and
Watchkeeping for Seafarers, 1978, as amended and International Agreements or
Covenants related thereto and its Implementing Rules and Regulations.
These sample questions have been reviewed and validated by our respective Board
of Examiners which may serve as a guide for the review of aspiring Marine Deck and
Engineering Officers, towards the successful completion of the Theoretical
Examination.
The following sample questions do not reflect the actual set of database of questions
given during the theoretical examination. Examinees are encouraged to study the
contained sample questions and probable answers as they are intended to give an
indication of the format and difficulty level of the theoretical examination.
You may access these guide questionnaires with your smart gadgets anywhere and
anytime at your convenience. Please consider the environment before printing.
Thank you.
FUNCTION 1 Competence 4
1.
2.
3.
Fuel injectors used in heavy fuel oil systems are usually provided with
cooling to reduce_____.
4.
What will happen if the needle valve in a fuel injection nozzle sticks
open?
5.
A fuel leak occurs in the high pressure fuel piping between the injection
pump and fuel nozzle. This requires repair because of the_____.
6.
7.
8.
9.
10.
11.
12.
14.
15.
16.
17.
Which characteristic of the theoretical Otto cycle does not occur in the
theoretical Diesel cycle_____.
18.
19.
20.
21.
The difference in crank lead between the upper and lower cranks of an
opposed piston engine causes the lower crankshaft to______.
22.
23.
24.
Which of the factors listed has the greatest effect on the mechanical
efficiency of a diesel engine?
25.
26.
27.
A leak at the intake valve of 2-stage compressor at the 2nd stage will
cause high _____________.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
A material use to protect the internal parts of air compressor from solid
particles which can be sucked along with fresh air is called____.
40.
41.
The expansion tank for the jacket cooling water which is a closed cooling
type is used to ___________.
42.
44.
45.
46.
The replacement piping for diesel engine high pressure fuel systems
must be the same length and diameter as the original piping to_____.
47.
When installing a new rotary pump, the suction piping should _____.
48.
Which among the following items below causes white ice formation?
49.
50.
Burned gas from each cylinder is directed to the exhaust manifold which
is part of___________.
51.
The inlet pipe connection of dirty oil in disc type centrifugal purifier is
located at the __________.
52.
The shaft coupling for the gear pump is prevented from rotating on the
shaft by which of the following items listed below?
53.
54.
55.
56.
58.
59.
60.
61.
62.
63.
64.
The static suction lift of a pump is the difference in elevation between the
_____.
65.
66.
67.
68.
69.
Which of the following boiler fittings is the most important in the boiler for
the prevention of over pressure?
70.
A high reading at a salinity cell located in the loop seal between two
stages of a flash type evaporator indicates_____.
71.
73.
74.
Which of the listed interlocks stops the valve in the remote operating
valve line of air starting system from opening when engaged?
75.
76.
77.
78.
A leak of intake valve of 2-stage compressor at the 2nd stage will cause
high ____________.
79.
80.
81.
Diesel engine jacket water is used in the fresh water distillation process
as the __________.
82.
83.
84.
What is the function of the after-coolers installed in the diesel engine air
intake system?
85.
While at sea, the flash type evaporator is discharging the output to the
boiler water reserve feed tanks. If it becomes necessary to reduce the
evaporator feed water temperature to below 165oF, you should _____.
87.
As the pump speed increases, its NPSH (Net positive suction head)
requirement thereby _________.
88.
89.
90.
91.
92.
93.
94.
95.
Which of the following is the possible cause why a lube oil pump fails to
build up discharge pressure?
96.
97.
98.
99.
100. After the installation of new impeller wearing rings by pressing them onto
the pump impeller hub, it is advisable to _____.