Beruflich Dokumente
Kultur Dokumente
BS 6422:1983
ISO 7546:1983
Method for
UDC 624.132:621.879.322.017.2:629.11.071.2
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
Volumetric rating of
loader and front
loading excavator
buckets used for
earth-moving
BS 6422:1983
Date of issue
Comments
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
BS 6422:1983
Contents
BSI 09-1999
Page
Inside front cover
ii
1
1
1
2
3
7
1
2
3
4
5
6
7
7
Inside back cover
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
Committees responsible
National foreword
1
Scope and field of application
2
References
3
Restrictions and limitations
4
Definitions and symbols
5
Volumetric ratings
6
Expression of volumetric ratings
Figure 1 Bucket
Figure 2 X and Y dimensions for irregular side sheet
Figure 3 Basic bucket
Figure 4 Extended straight cutting edge
Figure 5 Extended back sheet
Figure 6 Irregular cutting edge
Figure 7 Extended cutting edge and extended back sheet
Table
Publications referred to
BS 6422:1983
National foreword
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
pages 1 to 8, an inside back cover and a back cover.
This standard has been updated (see copyright date) and may have had
amendments incorporated. This will be indicated in the amendment table on the
inside front cover.
ii
BSI 09-1999
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
This British Standard has been prepared under the direction of the
Road Engineering Standards Committee and is identical with
ISO 7546:1983 Earth-moving machinery Loader and front loading excavator
buckets Volumetric ratings published by the International Organization for
Standardization (ISO).
ISO 7456 was produced as a result of international discussion in which the UK
took an active part.
Terminology and conventions. The text of the International Standard has
been approved as suitable for publication as a British Standard without
deviation. Some terminology and certain conventions are not identical with those
used in British Standards; attention is drawn especially to the following.
The comma has been used as a decimal marker. In British Standards it is current
practice to use a full point on the baseline as the decimal marker.
Wherever the words International Standard appear, referring to this standard,
they should be read as British Standard.
Cross-references. There are no corresponding British Standards for
ISO 7131 and ISO 7135, which are in course of preparation and to which
reference is made in the text. As these standards are referred to for information
only, the validity of this British Standard is not affected.
A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards are responsible for their correct application.
BS 6422:1983
2 References
ISO 7131, Earth-moving machinery Loaders Terminology1).
ISO 7135, Earth-moving machinery Excavators Terminology1).
Figure 1 Bucket
1)
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
1.1 This International Standard specifies a procedure for approximating the volume of typical materials
contained in the bucket of front end loaders and excavators with front loading bucket. The volume ratings
are based on the inside dimensions of the bucket and representative volumes on top of the bucket.
1.2 The method employs the technique of dividing the complex shape of the material in the bucket into
simple geometric forms to allow volume calculations of different bucket configurations.
1.3 The rating method is intended to provide a consistent means of comparing bucket capacities. It is not
intended to define actual capacities that might be observed in any specific application.
BSI 09-1999
BS 6422:1983
3.3 Only buckets with an X/Y ratio greater than 12 shall be considered by the rating method(s).
(See Figure 2.)
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
BSI 09-1999
BS 6422:1983
5 Volumetric ratings
5.1 Basic bucket
BSI 09-1999
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
The back sheet does not extend beyond a transverse line connecting the rear corners of the side sheets and
the cutting edge does not extend beyond a transverse line connecting the front corners of the side sheets.
5.1.1 The strike plane passes through a line along the top of the back sheet at the rear and a line along the
top of the cutting edge at the front as shown in Figure 3.
5.1.2 The volumetric capacity is calculated as shown in Figure 3.
BS 6422:1983
BSI 09-1999
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
The cutting edge is straight in the transverse direction and extends beyond a transverse line connecting
the front corners of the side sheets and the back sheet does not extend beyond a transverse line connecting
the rear corners of the side sheets.
5.2.1 The strike plane passes through a line along the cutting edge at the front and a line along the top of
the back sheet at the rear as shown in Figure 4.
5.2.2 The volumetric capacity is calculated as shown in Figure 4.
BS 6422:1983
BSI 09-1999
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
BS 6422:1983
BSI 09-1999
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
BS 6422:1983
BSI 09-1999
Increments
0,02
0,05
0,1
0,2
0,5
1,0
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
blank
BS 6422:1983
Publications referred to
See national foreword.
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
BSI 09-1999
BS 6422:1983
ISO 7546:1983
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: 020 8996 7111. Fax: 020 8996 7048.
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: 020 8996 7002. Fax: 020 8996 7001.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the internationalstandardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means electronic, photocopying, recording or otherwise without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
written permission of BSI must be obtained.
BSI
389 Chiswick High Road
London
W4 4AL
LICENSED TO INDIAN INSTITUTE OF TECHNOLOGY - KHARAGPUR, FOR INTERNAL USE AT THIS LOCATION ONLY, SUPPLIED BY BOOK SUPPLY BUREAU.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: 020 8996 9000. Fax: 020 8996 7400.