Beruflich Dokumente
Kultur Dokumente
Vaibhav Doshi
Assistant Professor
L.J. Institute of Engineering & Technology
Abstract
The paper presents an experimental activity carried out on RC beams strengthened in flexure and shear with different configurations
of CFRP laminates. Currently many building and other structure are deteriorated due to age or poor construction. There are many
techniques used for retrofitting purpose like jacketing, fiber reinforced polymer (FRP) wrapping etc. This research is basically to
strengthen and redesign existing structure. This research work includes Strengthening of full size beam
(150mm*150mm*1000mm). Flexure or shear-critical beams were provided with CFRP longitudinal sheets like single layer, double
layers etc or U-wraps, respectively. Flexureshear critical beams were provided with shear or combined systems. Concrete beams
reinforced internally with steel and externally with carbon FRP. Laminate applied after the concrete had cracked were tested under
two-point bending. Result show that FRP is very effective for flexural strengthening. Different type of wrapping of the FRP
laminate combined with adhesive bonding is effective in anchoring the laminate.
Keywords: Carbon fiber, Moment carrying capacity, Retrofitting, Strengthening, Wrapping
________________________________________________________________________________________________________
I.
INTRODUCTION
A structure is designed for a specific period and depending on the nature of the structure and surrounding environment, its life
varies. Depending on usage of structure life of the structure are decided. During the life span of structural deterioration happens.
The deterioration can be mainly due to environmental effects, which includes corrosion of steel, gradual loss of strength with
ageing, repeated high intensity loading, variation in temperature, freeze-thaw cycles, contact with chemicals and saline water and
exposure to ultra-violet radiations. Now to compensate deterioration, structure should be either replaced or properly retrofitted. As
complete replacement or reconstruction of the structure costs very high compared to strengthening or retrofitting, so generally it is
preferred to retrofit or strengthened the structure.
Retrofitting works are generally done by some techniques like FRP wrapping, Jacketing, near surface mounting reinforcing etc.
Till date mainly Glass fibers, carbon fibers, basalt fiber, aramid fiber etc. are used for retrofitting works. Carbon fibers can be used
for the same purpose. Carbon fiber has very high tensile strength and is also very lightweight. When it bonded to the exterior of a
concrete column, beam, or slab, it can add significant strength without adding weight that would increase the load on foundations
and other structural members. Carbon fiber can be bonded to concrete, masonry, steel and wood structures using a specially
formulated structural epoxy to increase the load carrying capacity and ductility.
II. PHYSICAL AND MECHANICAL PROPERTIES
Physical Properties
Carbon Fibre has High Strength to Weight Ratio (also known as specific strength). Carbon Fibre is very rigid. Carbon fibre is very
rigid. Carbon fibre reinforced plastic is over 4 times stiffer than Glass reinforced plastic, almost 20 times more than pine, 2.5 times
greater than aluminium. Carbon fibre is Corrosion Resistant and Chemically Stable. Although carbon fibre themselves do not
deteriorate measurably, Epoxy is sensitive to sunlight and needs to be protected. Carbon fibre is Electrically Conductive. Carbon
Fibre has good Tensile Strength and fatigue resistance. Carbon fibre can be made to feel quite soft to the hand and can be made
into or more often integrated into protective clothing for firefighting. Carbon fibre low coefficient of thermal expansion. Carbon
Fibres are brittle, in other words carbon fibre does not bend much before failing. Carbon is also very good resistor of ultra-violate
rays. They do not degrade under ultra-violate rays. Carbon Fibre is Relatively Expensive. The low maintenance requirement of
carbon fibre is a further advantage.
Mechanical Properties
Mechanical properties of Carbon fibres are as given in following Table 1.
315
Table 1
Mechanical Properties
Technical data
300 g/m2
330
Elastic modulus
(KN/mm2)
260
(g/m2)
3900
(main direction)
300
Density (g/cm3)
1.8
1.55
0.176
50:100
15 Kg
22
52
1.0
1 (Days)
Failure in concrete
0.25 0.35 kg / sq meter
316
Concrete
Concrete used in this experiment are of M25 grade general concrete. No any admixture is used.
IV. MIX DESIGN
The specified design strength of concrete is 25MPa at 28 days. The specific gravity of Fine Aggregates (FA) and Coarse Aggregates
(CA) is 2.61 and 2.84 respectively. The standard deviation can be taken as 5MPa. Ordinary Portland cement was used of 53grade.
Coarse aggregate is found to be Absorptive to the extent of 1% and free surface moisture in sand is found to be 2%. According to
IS10262-1982 clause 3.3 Table no 3. The mixing water content calculated is 178 kg/m 3. Mix proportion of M25 grade is shown in
Table 3 & 4.
Water
Cement
178
360 kg
0.49
Table - 2
Mix proportion
Fine Aggregates Coarse Aggregates
697 kg
1213 kg
1.94
3.37
Table - 3
Concrete mix design quantities
Grade of concrete: M25
Coarse aggregate(20mm): 2.65
Type of exposure: Mild
Coarse Aggregate(10mm): 2.65
Sp. Gravity of cement: 3.15 Maximum Water Cement Ratio: 0.4 95
Fine Aggregate: 2.65
Beam
designation
Control (not
bonded)
1-layer
bonded
2-layer
bonded
At mid
span
Fully Ushaped
Partially U-shaped
strips
45 degree
strips
CB
FB-1L
FB-2L
FB-ML
FB-UL
FB-PUL
FB-AL
Cured
28 days
Table - 5
Curing specimen details (150x150x1000mm):
CB
FB-1L FB-2L FB-ML FB-UL FB-PUL
3 nos. 3 nos. 3 nos.
3 nos.
3 nos.
3 nos.
FB-AL
3 nos.
The beams CB, FB-1L, FB-2L, FB-ML, FB-UL, FB-PUL, FB-AL cured for 28 days were tested on the Flexural Testing machine.
The following results of failure load were found out for Plain concrete beams, One sided CFRP wrapped concrete beams, Two
sided parallel CFRP wrapped concrete beams, Two sided parallel CFRP, at mid span CFRP, U shaped strips CFRP, partially U
shaped strips CFRP, 45 degree strips CFRP. The details of the load are thus given in the table 7 below.
Table - 6
Deflection and Load result
Point load (KN)
CB FB-1L FB-2L FB-ML
33
33
33
33
53
53
53
53
53
6
8
64
76
64
84
64
96
64
132
64
113
10
86
92
102
141
124
Deflection
FB-UL
33
317
12
91
99
106
145
126
14
16
86
61
102
67
109
98
149
121
131
101
Comparison of normal crack beam at 6mm deflection without wrapping to single layer carbon wrapping, double layer wrapping,
at mid span wrapping, u shaped strips wrapping crack beam at 6 mm deflection. Figure 2 shows the graphical representation of
moment carrying capacity(kn-m) versus deflection(mm) graph and Figure 3 shows the graphical representation of point load(KN)
versus deflection(mm) graph as below.
Beam description
Increase in moment carrying capacity comparing with Plain Concrete beam. (%)
12-18
2
3
4
15-30
35-50
60-75
318
Also the strength of beam wrapped at tension side was greater than the beams wrapped at two parallel sides. Therefore, from
the above results the beam wrapped at tension side gives better results so from economic point of view CFRP wrapped at tension
sides is desirable.
VI. CONCLUSION
From the above experiment it is clear that with the help of fabric wrapping strength of the existing member increase. For the
mentioned size of the beam it is clear that if we wrapped the beam with mentioned carbon fabric than minimum 1.5 times strength
increase in the both the case flexure and shear. Moment carrying capacity of single layer beam, double layer beam, at centre and
fully u shaped beam is increase by 12-18%, 15-30%, 35-50% and 60-75% respectively. Maximum moment carrying capacity of
single layer beam, double layer beam, at centre and fully u shaped beam is 15.3 kn-m, 16.35 kn-m, 19.65 kn-m and 22.35 kn-m
respectively.
ACKNOWLEDGMENT
For this thesis work I would like to thanks to my guide Mr.Vaibhav Doshi for their sincere guidance and help to carry out my
experiments.
REFERENCES
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10]
[11]
[12]
[13]
[14]
Ratan Kharatmol , Pankaj Sananse , Rohit Tambe, Ms.Raksha Khare Strengthening of Beams Using Carbon Fibre Reinforced Polymer, International Journal
of Emerging Engineering Research and Technology, Volume 2, Issue 3, June 2014
Jiangfeng Dong, Qingyuan Wang, Dong He, Zhongwei Guan CFRP sheets for Flexural Strengthening of RC Beams, IEEE 2011
Ehsan Ahmed, Habibur Rahman Sobuz and Norsuzailina Mohamed Sutan Flexural performance of CFRP strengthened RC beams with different degrees of
strengthening schemes , IJPS, May 2011
Asad ur Rehman Khan and Shamsoon Fareed Behaviour of Reinforced Concrete Beams Strengthened by CFRP Wraps with and without End Anchorages,
ELSEVIER - 2013
R.A. Hawileh, W. Nawaz, J.A. Abdalla and E.I. Saqan Effect of flexural CFRP sheets on shear resistance of reinforced concrete beams, ELSEVIER, Dec
2013
Sato Y, Ueda T, Katkuta Y, Tanaka T. Shear reinforcing effect of carbon fiber sheet attached to side of reinforced concrete beams In: 3rd International
conference on advanced composite materials in bridges and structures. Montreal; 1996. p. 62128.
Hamidreza Tahsiri, Omid Sedehi, Alireza Khaloo and Elias Molaei Raisi, Experimental study of RC jacketed and CFRP strengthened RC beams,
ELSEVIER, Jul - 2015
Abhijit Mukherjee and Gopal L. Rai, Performance of reinforced concrete beams externally prestressed with fiber composites, ELSEVIER, May - 2008
Massimiliano Bocciarelli, Serena Gambarelli, Nicola Nistico, Marco Andrea Pisani and Carlo Poggi, Shear failure of RC elements strengthened with steel
profiles and CFRP Wraps, ELSEVIER, June 2014
Rahul kumar satbhaiya, Shishir gupta and T.R Arora, Rehabilitation and Strengthening of R.C.C. STRUCTURES by using FRP composites, International
Journal of Emerging Technology and Advanced Engineering, Volume 3, Issue 10, October 2013
J. F. Bonacci and M. Maalej Behavioral trends of RC beams strengthened with externally bonded FRP Journal of Composites for Construction, Vol. 5,
No.2, May, 2001, 102-113.
Esfahani MR, Kianoush MR, Tajari AR (2007) Flexural behaviour of reinforced concrete beams strengthened by CFRP sheets Eng. Struct., 29: 24282444.
Grace NF, Sayed GA, Soliman KA, Saleh RK. Strengthening reinforced concrete beams using fiber reinforced polymers (FRP) laminate. ACI Struct 1998;
96:18694.
A.A. El-Ghandour, Experimental and analytical investigation of CFRP flexural and shear strengthening efficiencies of RC beams, ELSEVIER, Oct - 2010
319