Beruflich Dokumente
Kultur Dokumente
STINGER 4792
BT MODEL
CAUTION Do not use this specification sheet as a load rating chart. The format of data
is not consistent with the machine chart and may be subject to change.
LOAD RATINGS
BOOM LENGTH
OPERATING
RADIUS
(FT)
5
8
10
12
14
16
20
25
30
35
40
45
50
55
60
65
70
75
80
29 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
78
71
67
62
58
53
41
21
47,000*
36,800*
30,900*
26,100*
21,900*
18,800*
14,200*
10,400*
44 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
78
75
73
70
67
61
53
45
34
19
20,300*
20,300*
20,300*
19,400*
17,300*
13,900*
10,900*
8,625*
6,925*
5,225*
57 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
79
77
75
73
68
63
57
51
44
36
26
1
71 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
18,400*
17,400*
16,800*
15,900*
13,400*
10,600*
8,625*
6,925*
5,625*
4,625*
3,725*
1,225*
78
77
73
69
65
60
56
50
45
38
31
21
14,600*
13,800*
12,300*
10,400*
8,425*
6,925*
5,625*
4,625*
3,725*
3,025*
2,425*
2,025*
84 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
79
76
73
69
66
62
58
53
49
44
39
32
25
14
12,300*
10,900*
9,800*
8,225*
6,725*
5,625*
4,625*
3,725*
3,025*
2,425*
2,025*
1,525*
1,225*
825*
92 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
78
75
71
68
65
61
57
53
49
45
40
35
28
9,825*
9,025*
7,425*
6,325*
5,425*
4,625*
3,725*
3,025*
2,425*
2,025*
1,525*
1,225*
825*
AREA OF OPERATION
DO NOT OPERATE
IN SHADED AREA
WITHOUT
OPTIONAL FRONT
STABILIZER
Overhaul Ball
STOWED JIB DEDUCTIONS (POUNDS)
700
500
350
300
250
200
175 lbs
200 lbs
250 lbs
VERIFY OPERATIONAL MODE SETTING ON LMI DISPLAY BEFORE LIFTING WITH JIB
50
55
60
65
70
75
78
80
Retracted 26 ft Jib
Extended 44 ft Jib
725
1,025
1,525
2,325
3,225
4,325
4,925
5,325
425
725
1,125
1,525
2,025
2,525
2,825
3,125
CENTERLINE OF ROTATION
GENERAL NOTES
1. The operator must read and understand the Owner's Manual before operating this crane.
2. Positioning or operation of crane beyond areas shown on this chart is not intended or approved except where
specified in Owner's Manual.
3. Loaded boom angles at specified boom lengths give only an approximation of the operating radius. The boom angle
before loading should be greater to account for deflections. Do not exceed the operating radius for rated loads.
4. Use rating of next longer boom for boom lengths not shown. Use rating of next greater radius for load radii not shown.
5. Boom must be fully retracted when jib is erected before lowering below minimum angle. Retracted jib has no lifting
capacity below a 50 boom angle.
6. Use rating of next lower boom angle for boom angles not shown on jib load rating chart.
7. Lifting off the main boom point while the swing around jib is erected is not intended or approved.
8. Do not lower boom into this area, as hydraulic pressure will not allow raising the boom without retracting boom first.
9. Crane load ratings on outriggers are based on freely suspended loads with the machine leveled and standing on a firm
uniform supporting surface. No attempt shall be made to move a load horizontally on the ground in any direction.
10. Practical working loads depend on supporting surface, wind and other factors affecting stability such as hazardous
surroundings, experience of personnel, and proper handling, must all be taken into account by the operator.
11. The maximum load which may be telescoped is limited by hydraulic pressure, boom angle, and boom lubrication. It is
safe to attempt to telescope any load within the limits of the load rating chart.
INFORMATION
1. Deductions must be made from rated loads for stowed jib, optional attachments, hooks and loadblocks (see deduction
chart). Weights of slings and other load handling devices shall be considered a part of the load.
2. Crane load ratings with outriggers are based on outriggers and stabilizers extended and set with all load removed
from the carrier wheels.
3. Load ratings do not exceed 85% of tipping load.
DEFINITIONS
1. Operating radius is the horizontal distance from the axis of rotation to the center of the vertical hoist line or load hook
with load suspended.
2. Loaded boom angle as shown in the Load Ratings Chart is the included angle between the horizontal and longitudinal
axes of the boom base after lifting rated load at rated radius.
STINGER 4792
RM MODEL
CAUTION Do not use this specification sheet as a load rating chart. The format of data
is not consistent with the machine chart and may be subject to change.
LOAD RATINGS
BOOM LENGTH
OPERATING
RADIUS
(FT)
5
8
10
12
14
16
20
25
30
35
40
45
50
55
60
65
70
75
80
29 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
78
71
67
62
58
53
41
21
47,000*
36,800*
30,900*
26,100*
21,900*
18,800*
14,200*
10,400*
44 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
78
75
73
70
67
61
53
45
34
19
20,300*
20,300*
20,300*
19,400*
17,300*
13,900*
10,900*
8,625*
6,925*
5,225*
57 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
79
77
75
73
68
63
57
51
44
36
26
1
71 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
18,400*
17,400*
16,800*
15,900*
13,400*
10,600*
8,625*
6,925*
5,625*
4,625*
3,725*
1,225*
78
77
73
69
65
60
56
50
45
38
31
21
14,600*
13,800*
12,300*
10,400*
8,425*
6,925*
5,625*
4,625*
3,725*
3,025*
2,425*
2,025*
84 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
79
76
73
69
66
62
58
53
49
44
39
32
25
14
12,300*
10,900*
9,800*
8,225*
6,725*
5,625*
4,625*
3,725*
3,025*
2,425*
2,025*
1,525*
1,225*
825*
92 FT
LOADED
LOAD
BOOM
RATING
ANGLE
(LB)
(DEG)
78
75
71
68
65
61
57
53
49
45
40
35
28
9,825*
9,025*
7,425*
6,325*
5,425*
4,625*
3,725*
3,025*
2,425*
2,025*
1,525*
1,225*
825*
700
500
350
300
250
200
AREA OF OPERATION
360 Full Capacity
Area of
Operation
Overhaul Ball
175 lbs
200 lbs
250 lbs
VERIFY OPERATIONAL MODE SETTING ON LMI DISPLAY BEFORE LIFTING WITH JIB
50
55
60
65
70
75
78
80
725
1,025
1,525
2,325
3,225
4,325
4,925
5,325
425
725
1,125
1,525
2,025
2,525
2,825
3,125
CENTERLINE OF ROTATION
GENERAL NOTES
1. The operator must read and understand the Owner's Manual before operating this crane.
2. Positioning or operation of crane beyond areas shown on this chart is not intended or approved except where
specified in Owner's Manual.
3. Loaded boom angles at specified boom lengths give only an approximation of the operating radius. The boom angle
before loading should be greater to account for deflections. Do not exceed the operating radius for rated loads.
4. Use rating of next longer boom for boom lengths not shown. Use rating of next greater radius for load radii not shown.
5. Boom must be fully retracted when jib is erected before lowering below minimum angle. Retracted jib has no lifting
capacity below a 50 boom angle.
6. Use rating of next lower boom angle for boom angles not shown on jib load rating chart.
7. Lifting off the main boom point while the swing around jib is erected is not intended or approved.
8. Do not lower boom into this area, as hydraulic pressure will not allow raising the boom without retracting boom first.
9. Crane load ratings on outriggers are based on freely suspended loads with the machine leveled and standing on a firm
uniform supporting surface. No attempt shall be made to move a load horizontally on the ground in any direction.
10. Practical working loads depend on supporting surface, wind and other factors affecting stability such as hazardous
surroundings, experience of personnel, and proper handling, must all be taken into account by the operator.
11. The maximum load which may be telescoped is limited by hydraulic pressure, boom angle, and boom lubrication. It is
safe to attempt to telescope any load within the limits of the load rating chart.
INFORMATION
1. Deductions must be made from rated loads for stowed jib, optional attachments, hooks and loadblocks (see deduction
chart). Weights of slings and other load handling devices shall be considered a part of the load.
2. Crane load ratings with outriggers are based on outriggers and stabilizers extended and set with all load removed
from the carrier wheels.
3. Load ratings do not exceed 85% of tipping load.
DEFINITIONS
1. Operating radius is the horizontal distance from the axis of rotation to the center of the vertical hoist line or load hook
with load suspended.
2. Loaded boom angle as shown in the Load Ratings Chart is the included angle between the horizontal and longitudinal
axes of the boom base after lifting rated load at rated radius.
STINGER 4792
BT MODEL
WINCH DATA
1 Part Line
Winch
Standard
Stationary
Winch
BLOCK TYPE
2 Part Line
3 Part Line
4 Part Line
TWO
SHEAVE
LOAD
BLOCK
5 Part Line
OVERHAUL
BALL
ONE
SHEAVE
LOAD
BLOCK
ONE
SHEAVE
LOAD
BLOCK
TWO
SHEAVE
LOAD
BLOCK
Cable
Supplied
Lift and
Speed
Lift and
Speed
Lift and
Speed
Lift and
Speed
Lift and
Speed
9/16 Diam
IWRC XXIP
10,500 lb
186 fpm
21,000 lb
93 fpm
31,500 lb
62 fpm
42,000 lb
46 fpm
47,000 lb
37 fpm
9/16 Diam
Rotation Resistant
6,720 lb
186 fpm
13,440 lb
93 fpm
20,100 lb
62 fpm
26,880 lb
46 fpm
33,600 lb
37 fpm
Overhaul Ball
1 Sheave Block
2 Sheave Block
CAUTION
Overload and anti-two-block systems must be in good operating
condition before operating crane. Refer to Owners Manual.
Keep at least 3 wraps of loadline on drum at all times.
Use only 9/16 diameter cable with 37,000 lb breaking strength on
this machine.
2 MOUNTING CONFIGURATIONS
INCLUDED OPTIONS
CHASSIS RECOMMENDATIONS
STINGER BT4792 - Behind Cab Mounting Configuration
Combined Axle Weight Rating
60,000 Ib (27 210 kg)
Front Axle Weight Rating
20,000 Ib (9 067 kg)
Rear Axle Weight Rating
Wheel base
Cab to Axle
Afterframe
Frame Section Modulus
RBM per Frame Rail
Frame Height (Unloaded)
Exhaust Position
STINGER 4792
RM MODEL
WINCH DATA
1 Part Line
Winch
Standard
Stationary
Winch
BLOCK TYPE
2 Part Line
3 Part Line
4 Part Line
TWO
SHEAVE
LOAD
BLOCK
5 Part Line
OVERHAUL
BALL
ONE
SHEAVE
LOAD
BLOCK
ONE
SHEAVE
LOAD
BLOCK
Cable
Supplied
Lift and
Speed
Lift and
Speed
Lift and
Speed
Lift and
Speed
Lift and
Speed
9/16 Diam
IWRC XXIP
10,500 lb
186 fpm
21,000 lb
93 fpm
31,500 lb
62 fpm
42,000 lb
46 fpm
47,000 lb
37 fpm
9/16 Diam
Rotation Resistant
6,720 lb
186 fpm
13,440 lb
93 fpm
20,100 lb
62 fpm
26,880 lb
46 fpm
33,600 lb
37 fpm
2
2 MOUNTING
MOUNTING CONFIGURATIONS
CONFIGURATIONS
TWO
SHEAVE
LOAD
BLOCK
Overhaul Ball
1 Sheave Block
2 Sheave Block
CAUTION
Overload and anti-two-block systems must be in good operating
condition before operating crane. Refer to Owners Manual.
Keep at least 3 wraps of loadline on drum at all times.
Use only 9/16 diameter cable with 37,000 lb breaking strength on
this machine.
INCLUDED OPTIONS
Manufacturer
Standard Engine
Standard Horsepower
Power steering
Electric Horn
Factory A/C
Standard Torque
Full Tank Capacity
Standard Transmission
Speed Standard Transmission
CHASSIS RECOMMENDATIONS
Brakes
Exhaust Position
Wheel base
Cab to Axle
Afterframe
Frame Section Modulus
RBM per Frame Rail
Frame Height (Unloaded)
261" (6.62 m)
192" (4.87 m)
114" (2.89 m)
30.0 in3 (491 cm3)
1,860,000 in/Ib (32 950 kg/m)
40" (7.62 m)
Exhaust Position
STINGER 4792
BT MODEL
SPECIFICATIONS
BOOM
CONTROLS
WINCH
Hydraulic winch with gear motor and planetary reduction gearing
provides 2-speed operation. First layer rope pull is 11,400 Ib (5 170
kg). Wire rope size is 9/16" (14 mm) with 37,000 Ib (16 783 kg)
breaking strength.
OUTRIGGERS
Front outriggers are Link-Type. The maximum width over main
outrigger pad is 21 9" (6.62 m), main outrigger spread at maximum
ground penetration is 21 4" (6.51 m).
Rear outriggers are Out & Down type. The maximum width over
auxiliary outrigger pads is 17 6" (5.34 m).
SUBFRAME
OPERATING SPEEDS
Mainframe / turret assembly planetary gear rotation provides 180
rotation (370 with optional front bumper outrigger). Swing rotation is
75 seconds. Boom up/down is 41/30 seconds and boom
extend/retract is 80/36 seconds.
HYDRAULICS
Three-section pump allows the operator to perform simultaneous
crane operations (winch, boom and swing). Capacities are 32, 17 and
8 gpm (122, 64 and 30 L/m). Hydraulic tank capacity is 90 gal (342 L).
STINGER 4792
RM MODEL
SPECIFICATIONS
BOOM
CONTROLS
WINCH
Hydraulic winch with gear motor and planetary reduction gearing
provides 2-speed operation. First layer rope pull is 11,400 Ib (5 170
kg). Wire rope size is 9/16" (14 mm) with 37,000 Ib (16 783 kg)
breaking strength.
OUTRIGGERS
Rear outriggers are Link-Type. The maximum width over main
outrigger pad is 21 9" (6.62 m), main outrigger spread at maximum
ground penetration is 21 4" (6.51 m).
Front outriggers are Out & Down type. The maximum width over
auxiliary outrigger pads is 17 6" (5.34 m).
SUBFRAME
OPERATING SPEEDS
Mainframe / turret assembly planetary gear rotation provides 180
rotation (370 with optional front bumper outrigger). Swing rotation is
75 seconds. Boom up/down is 41/30 seconds and boom
extend/retract is 80/36 seconds.
HYDRAULICS
Three-section pump allows the operator to perform simultaneous
crane operations (winch, boom and swing). Capacities are 32, 17 and
8 gpm (122, 64 and 30 L/m). Hydraulic tank capacity is 90 gal (342 L).
STINGER 4792
Contacts
SALES
Tom Limbach
Sales Director, Terex Cranes
(319) 352-9357
Office:
Mobile:
(815) 703-3905
Office Fax: (319) 352-9395
tom.limbach@terexwaverly.com
Email:
Diane Sheedy
Director of International Sales
Office:
(319) 352-9326
Office Fax: (319) 352-9395
Email:
diane.sheedy@terexwaverly.com
Bruce Kramer
Sales Manager, Terex Cranes
Office:
(319) 352-9347
(815) 703-3896
Mobile:
Office Fax: (319) 352-9395
bruce.kramer@terexwaverly.com
Email:
Chad Brandenburg
Sales Coordinator, Terex Cranes
Office:
(319) 352-9356
Mobile:
(910) 367-3152
Office Fax: (319) 352-9395
Email:
chad.brandenburg@terexwaverly.com
Angie Scribner
Sales Assistant, Terex Cranes
Office:
(319) 352-9309
Office Fax: (319) 352-9395
Email:
angie.scribner@terexwaverly.com
SERVICE PARTS
Roger Jones
Service Manager Product Support
Office:
(910) 395-8504
Mobile:
(910) 367-6260
Office Fax: (910) 395-8538
Email:
rjones@american-crane.com
Dino Nelson
Service Training Specialist
Office:
(319) 352-9338
Mobile:
(815) 703-1800
Office Fax: (319) 352-9378
Email:
dino.nelson@terexwaverly.com
Jim Chivers (Boom Trucks)
Service Manager Product Support
Office:
(319) 352-9352
Mobile:
(815) 703-3901
Office Fax: (319) 352-9378
Email:
jim.chivers@terexwaverly.com
Fred Backer (Boom Trucks)
Service Technician
Office:
(319) 352-9388
Mobile:
(815) 703-6514
Office Fax: (319) 352-9378
Email:
fred.backer@terexwaverly.com
TEREX Cr
Cranes
anes
106-12th Street S.E.
Waverly, IA 50677-9466 USA
For more information, product demonstration, or detail on purchase, lease and rental plans, please contact your local Terex Crane dealer.
We reserve the right to amend these specifications at anytime without notice. The only warranty applicable is our standard written warranty
applicable to the particular product an sale. We make no other warranty, expressed or implied.