Beruflich Dokumente
Kultur Dokumente
Bathtubs.
Faucets.
224100 - 1
Whirlpool baths.
Walk-in baths.
Bidets.
Lavatories.
Showers.
Bar sinks.
Kitchen sinks.
Laundry trays.
Dishwasher air-gap fittings.
Laminar-flow, faucet-spout outlets.
Disposers.
Hot-water dispensers.
Water closets.
Toilet seats.
Supply fittings.
Waste fittings.
224100 - 2
Retain "Product Data for Prerequisite WE 1( and Credit WE 2)" Subparagraph below for LEED-EB for
fixtures and equipment that consume water.
1.3
Product Data for Prerequisite WE 1[ and Credit WE 2]: Documentation indicating flow
and water consumption requirements.
PRODUCT DATA SHEET 3 - Lead Free: Manufacturer's statement of compliance with requirements
of California Assembly Bill AB 1953.
PRODUCT DATA SHEET 4 - Water Efficiency:
requirements of EPA WaterSense program.
224100 - 3
Faucet Washers and O-Rings: Equal to [10] <Insert number> percent of amount of each
type and size installed.
Faucet Cartridges and O-Rings: Equal to [5] <Insert number> percent of amount of
each type and size installed.
Flushometer-Tank Repair Kits: Equal to [5] <Insert number> percent of amount of each
type installed, but no fewer than [two] <Insert number> of each type.
Toilet Seats: Equal to [5] <Insert number> percent of amount of each type installed.
SCHEDULE 6 - WARRANTY
When warranties are required, verify with Owner's counsel that warranties stated in this article are not
less than remedies available to Owner under prevailing local laws.
PRODUCT DATA SHEET 0 - Special Warranty: Manufacturer agrees to repair or replace components
of [walk-in baths] [and] [whirlpool baths] that fail in materials or workmanship within
specified warranty period.
0.1
Verify available warranties and warranty periods for units and components.
0.2
0.3
0.4
Warranty Period for Residential Applications of Shells: [Five] [20] [30] <Insert
number> years from date of Substantial Completion.
Warranty Period for Residential Applications of Pumps and Blowers: [Five] [20] <Insert
number> years from date of Substantial Completion.
Warranty Period for Commercial Applications of Electronic Controls: Five years from
date of Substantial Completion.
PART 2 - PRODUCTS
See Editing Instruction No. 1 in the Evaluations for cautions about named manufacturers and products.
For an explanation of options and Contractor's product selection procedures, see Division 01 Section
"Product Requirements."
SCHEDULE 0 - BATHTUBS
Copy "Bathtubs" Paragraph below and re-edit for each type of bathtub required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each
bathtub.
PRODUCT DATA SHEET 0 - Bathtubs <Insert drawing designation>:
[Enameled steel] [FRP] [PMMA], with shower.
224100 - 4
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
0.2
Retain one of four lists of manufacturers below. First list is for enameled cast-iron bathtubs.
A.
B.
Kohler Co.
<Insert manufacturer's name>.
Clarion Bathware.
Florestone Products Co., Inc.
Praxis Industries, LLC; Aquarius Bathware.
Sterling; a Kohler company.
Swan Corporation (The).
<Insert manufacturer's name>.
224100 - 5
Fixture:
Drain Piping: NPS 1-1/2 (DN 40) cast-brass overflow, P-trap, and waste.
Drain Piping: Schedule 40 [ABS] [or] [PVC], NPS 1-1/2 (DN 40) P-trap, and
waste.
Single handle,
224100 - 6
Retain one of two lists of manufacturers below. First list is for pressure-balance faucets.
A.
B.
C.
D.
E.
F.
1.4
Shower Head:
A.
B.
Retain "Shower-Arm, Flow-Control Fitting" Subparagraph below only if retaining option that includes
arm and flange in "Type" Subparagraph above.
RESIDENTIAL PLUMBING FIXTURES
224100 - 7
Shower-Arm, Flow-Control Fitting: [Not required] [1.5 gpm (5.7 L/min.)] [2.0
gpm (7.6 L/min.)].
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
0.2
Retain one of four lists of manufacturers below. First list is for enameled cast-iron whirlpool baths.
A.
B.
Kohler Co.
<Insert manufacturer's name>.
224100 - 8
Standards: ASME A112.19.1/CSA B45.2 and UL 1795 for enameled [cast-iron] [-steel]
hydromassage bathtubs.
Standards: ANSI Z124.1.2 and UL 1795 for [FRP] [PMMA] hydromassage bathtubs.
General: Bathtub with air-entrained, water-jet nozzles and water circulation.
Fixture:
A.
B.
C.
D.
E.
F.
224100 - 9
Faucet:
A.
B.
C.
0.8
0.9
NSF Standard: Comply with NSF/ANSI 61, "Drinking Water System Components
- Health Effects," for faucet materials that will be in contact with potable water.
Description:
Fixture manufacturer's chrome-plated, solid-brass [individual
valves] [mixing valve] with over-rim tub filler.
Faucet Standard: ASME A112.18.1/CSA B125.1.
Supplies: NPS 1/2 (DN 15) copper tubing with ball, gate, or globe valves.
Waste Fittings:
A.
B.
C.
0.10 Water-Circulating System: Electric circulating pump complying with ASME A112.19.7
and with UL 1951, and listed and labeled as defined in NFPA 70, by a qualified testing
agency, and marked for intended location and application and plastic piping.
"Water Heater" Subparagraph below is a useful, but unnecessary, feature.
0.11 Water Heater: Electric, inline complying with UL 1951, and listed and labeled as defined
in NFPA 70, by a qualified testing agency, and marked for intended location and
application.
0.12 Unit Electrical Characteristics:
A.
B.
C.
D.
E.
F.
Copy "Whirlpool Baths" Paragraph below and re-edit for each type of PMMA air-massage bathtub
required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each airmassage bathtub. Do not use same designation as is used for another air-massage bathtub in other
Division 22 plumbing-fixture Sections. See Specification Coordination Checklist for other Sections
specifying air-massage bathtub.
RESIDENTIAL PLUMBING FIXTURES
224100 - 10
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
1.2
1.3
1.4
1.5
NSF Standard: Comply with NSF/ANSI 61, "Drinking Water System Components
- Health Effects," for faucet materials that will be in contact with potable water.
224100 - 11
Description:
Fixture manufacturer's chrome-plated, solid-brass [individual
valves] [mixing valve] with over-rim tub filler.
Faucet Standard: ASME A112.18.1/CSA B125.1.
Supplies: NPS 1/2 (DN 15) copper tubing with ball, gate, or globe valves.
Waste Fittings:
A.
B.
C.
1.10 Water-Circulating System: Electric circulating pump, complying with ASME A112.19.7
and with UL 1951, and listed and labeled as defined in NFPA 70, by a qualified testing
agency, and marked for intended location and application and plastic piping.
"Water Heater" Subparagraph below is a useful, but unnecessary, feature.
1.11 Water Heater: Electric, inline complying with UL 1951, and listed and labeled as defined
in NFPA 70, by a qualified testing agency, and marked for intended location and
application.
1.12 Unit Electrical Characteristics:
A.
B.
C.
D.
E.
F.
224100 - 12
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
0.2
0.3
Fixture:
A.
B.
C.
D.
E.
F.
G.
H.
I.
0.4
Faucet:
224100 - 13
NSF Standard: Comply with NSF/ANSI 61, "Drinking Water System Components
- Health Effects," for faucet materials that will be in contact with potable water.
Description:
Fixture manufacturer's chrome-plated, solid-brass [individual
valves] [mixing valve] with over-rim tub filler.[ Include diverter and hand
shower.]
Faucet Standard: ASME A112.18.1/CSA B125.1.
Mounting: Deck.
Supplies: NPS 1/2 (DN 15) copper tubing with ball, gate, or globe valves.
Waste Fittings:
A.
B.
C.
Copy "Walk-in Baths" Paragraph below and re-edit for each type of plastic, hydromassage, walk-in bath
required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each
walk-in bath.
PRODUCT DATA SHEET 1 - Walk-in Baths <Insert drawing designation>: Plastic, hydromassage,
with side-entry door, seat, and faucet.
Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from
manufacturers listed or a comparable product from other manufacturers.
1.1
224100 - 14
1.3
Fixture:
A.
B.
C.
D.
E.
F.
G.
H.
1.4
Faucet:
A.
B.
C.
D.
1.5
1.6
NSF Standard: Comply with NSF/ANSI 61, "Drinking Water System Components
- Health Effects," for faucet materials that will be in contact with potable water.
Description:
Fixture manufacturer's chrome-plated, solid-brass [individual
valves] [mixing valve] with over-rim tub filler.[ Include diverter and hand
shower.]
Faucet Standard: ASME A112.18.1/CSA B125.1.
Mounting: Deck.
Supplies: NPS 1/2 (DN 15) copper tubing with ball, gate, or globe valves.
Waste Fittings:
A.
B.
C.
224100 - 15
SCHEDULE 4 - BIDETS
Copy "Bidets" Paragraph below and re-edit for each type of bidet required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each
bidet.
PRODUCT DATA SHEET 0 - Bidets <Insert drawing designation>:
0.1 Basis-of-Design Product: Subject to compliance with requirements, provide Gerber
Plumbing Fixtures LLC; Aquasaver, or comparable product by one of the following:
A.
B.
C.
D.
E.
0.2
Fixture:
A.
B.
C.
D.
E.
F.
0.3
Faucet:
A.
B.
0.4
0.5
SCHEDULE 5 - LAVATORIES
224100 - 16
[Oval] [Rectangular],
In "Basis-of-Design Product" Subparagraph below retain "Wicker Park" or "Logan Square" for
rectangular lavatories; and retain "Brianne," "Allerton," "Maxwell," "Riverdale," or "Abigail" for oval
lavatories.
0.1 Basis-of-Design Product: Subject to compliance with requirements, provide Gerber
Plumbing Fixtures LLC; [Wicker Park] [Logan Square] [Brianne] [Allerton]
[Maxwell] [Riverdale] [Abigail], or comparable product by one of the following:
First list of manufacturers below is for enameled-steel lavatories.
A.
B.
C.
Fixture:
Standard:
ASME A112.19.1/CSA B45.2 for enameled [cast-iron] [-steel]
lavatories.
Standard: ANSI Z124.3 for PMMA lavatories.
Standard: ANSI Z124.3 and ANSI/ICPA SS-1 for solid-surface lavatories.
Standard: ASME A112.19.3/CSA B45.4 for stainless-steel lavatories.
Standard: ASME A112.19.2/CSA B45.1 for vitreous-china lavatories.
Type: [Flat rim with ledge] [Self-rimming].
Retain "Oval Nominal Size," ''Rectangular Nominal Size," or "Round Nominal Size" Subparagraph
below.
224100 - 17
Oval Nominal Size: [19 by 16 inches (483 by 406 mm)] [20 by 17 inches (508
by 432 mm)] <Insert dimensions>.
Rectangular Nominal Size: [18 by 15 inches (457 by 381 mm)] [19 by 16 inches
(483 by 406 mm)] [20 by 18 inches (508 by 457 mm)] [24 by 20 inches (610 by
508 mm)] <Insert dimensions>.
Round Nominal Size: [18 inches (457 mm)] [19 inches (483 mm)] <Insert
dimensions> in diameter.
Faucet-Hole Punching: [One hole] [Three holes, 2-inch (51-mm) centers]
[Three holes, 4-inch (102-mm) centers].
Faucet-Hole Location: [None] [Rim].
Color: [Not applicable] [White] <Insert color>.
Copy "Lavatories" Paragraph below and re-edit for each type of vitreous-china, pedestal lavatory
required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each
lavatory. Do not use same designation as is used for another lavatory in other Division 22 plumbingfixture Sections. See Specification Coordination Checklist for other Sections specifying lavatories.
PRODUCT DATA SHEET 1 - Lavatories <Insert drawing designation>:
vitreous china, pedestal.
[Oval] [Rectangular],
In "Basis-of-Design Product" Subparagraph below, retain "Wicker Park" or "Logan Square" for
rectangular lavatories or "Brianne," "Picureesque," "Allerton," or "Maxwell" for oval lavatories.
1.1 Basis-of-Design Product: Subject to compliance with requirements, provide Gerber
Plumbing Fixtures LLC; [Wicker Park] [Logan Square] [Brianne] [Picturesque]
[Allerton] [Maxwell], or comparable product by one of the following:
A.
B.
C.
D.
E.
1.2
Fixture:
A.
Oval Nominal Size: [20 by 17 inches (508 by 432 mm)] [24 by 18 inches (610
by 457 mm)] <Insert dimensions>.
Rectangular Nominal Size: [18 by 15 inches (457 by 381 mm)] [19 by 16 inches
(483 by 406 mm)] [20 by 18 inches (508 by 457 mm)] [24 by 20 inches (610 by
508 mm)] <Insert dimensions>.
Faucet-Hole Punching: [One hole] [Three holes, 2-inch (51-mm) centers]
[Three holes, 4-inch (102-mm) centers].
224100 - 18
Copy "Lavatories" Paragraph below and re-edit for each type of oval, integral-bowl countertop lavatory
required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each
lavatory. Do not use same designation as is used for another lavatory in other Division 22 plumbingfixture Sections. See Specification Coordination Checklist for other Sections specifying lavatories.
PRODUCT DATA SHEET 2 - Lavatories <Insert drawing designation>: Oval, [cultured marble,]
[solid surface,] integral bowl countertop.
Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from
manufacturers listed or a comparable product from other manufacturers.
2.1
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
2.2
Retain one of two lists of manufacturers below. First list below is for cultured-marble countertop
lavatories. Usually manufacturers of cultured-marble products only sell locally. See the International
Cast Polymer Alliance's Web site at www.icpa-hq.org or the NAHB Research Center's Web site at
www.nahbrc.org for a list of manufacturers near Project site.
A.
B.
C.
D.
E.
F.
G.
224100 - 19
InPro Corporation.
Swan Corporation (The).
Wilsonart International.
<Insert manufacturer's name>.
Fixture:
A.
B.
C.
D.
E.
F.
G.
General: Countertop lavatory with integral bowl(s) for mounting on base unit.
Backsplash:
[Integral with countertop] [Separate, same material as
countertop] [Not required].
Overall Rectangular Top Size: [25 by 17 inches (635 by 432 mm)] [31 by 19
inches (787 by 483 mm)] [49 by 22 inches (1245 by 559 mm)] [73 by 22 inches
(1854 by 559 mm)] <Insert dimensions> with [one] [two] [three] [four] bowl(s).
Bowl Size: Oval [19 by 16 inches (483 by 406 mm)] [20 by 17 inches (508 by
432 mm)] <Insert dimensions>.
Faucet-Hole Punching: [One hole] [Three holes, 2-inch (51-mm) centers]
[Three holes, 4-inch (102-mm) centers].
Faucet-Hole Location: [Countertop] <Insert location>.
Color: [White] <Insert color>.
224100 - 20
1.2
1.3
224100 - 21
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
0.2
Retain one of two lists of manufacturers below. First list is for FRP showers.
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
224100 - 22
Copy "Showers" Paragraph below and re-edit for each type of accessible shower required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each
shower. Do not use same designation as is used for another shower in other Division 22 plumbing-fixture
Sections. See Specification Coordination Checklist for other Sections specifying showers.
PRODUCT DATA SHEET 1 - Showers <Insert drawing designation>: Accessible [FRP] [PMMA]
with seat, grab bar, base, and faucet.
Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from
manufacturers listed or a comparable product from other manufacturers.
1.1
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
1.2
Retain one of two lists of manufacturers below. First list is for FRP showers.
A.
B.
C.
D.
Standards: ANSI Z124.1.2 and ICC/ANSI A117.1 for roll-in shower compartments.
Nominal Size: [60 by 36 inches (1525 by 915 mm)] [72 by 36 inches (1830 by 915
mm)] <Insert dimensions>.
224100 - 23
Copy "Showers" Paragraph below and re-edit for each type of factory-fabricated cabinet shower required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each
shower. Do not use same designation as is used for another shower in other Division 22 plumbing-fixture
Sections. See Specification Coordination Checklist for other Sections specifying showers.
PRODUCT DATA SHEET 2 - Showers <Insert drawing designation>: Factory fabricated cabinet.
Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from
manufacturers listed or a comparable product from other manufacturers.
2.1
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
2.2
2.3
2.4
2.5
2.6
2.7
Size: [30 by 30 inches (762 by 762 mm)] [32 by 32 inches (815 by 815 mm)] [36 by 36
inches (915 by 915 mm)] [36 by 39 inches (915 by 990 mm)] [45 by 39 inches (1145
by 990 mm)] <Insert dimensions>.
Material: [Steel] [Composite] [Plastic], [front] [corner] [front and rear] access.
Color: [Not applicable] <Insert color>.
Accessibility Options: Grab bar and bench.
Faucet: <Insert faucet designation from "Shower Faucets" Article>.
224100 - 24
Supplies: NPS 1/2 (DN 15) copper tubing with shutoff valves.
Drain: Grid, NPS 2 (DN 50).
Fixture:
Retain option in "Standard" Subparagraph below for pressure-balance and thermostatic faucets.
A.
B.
C.
224100 - 25
Supply Connections: [NPS 1/2 (DN 15)] [NPS 3/4 (DN 20)].
Shower Head:
A.
B.
C.
D.
E.
Type: [Ball joint] [Without ball joint] [Ball joint and head integral with
mounting flange] [Integral with mounting flange] [Hand-held, grab-bar
mounted] [Hand-held, hook mounted].
Shower Head Material: [Metallic] [Nonmetallic] [Combined, metallic and
nonmetallic] with chrome-plated finish.
Spray Pattern: [Center-jet control] [Fixed] [Adjustable].
Integral Volume Control: [Required] [Not required].
Shower-Arm, Flow-Control Fitting: [Not required] [1.5 gpm (5.7 L/min.)] [1.75
gpm (6.7 L/min.)] [2.0 gpm (7.6 L/min.)].
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
224100 - 26
Retain one of five lists of manufacturers below. First list is for enameled cast-iron bar sinks.
A.
B.
C.
D.
Gerber Plumbing Fixtures LLC does not manufacture a product complying with requirements of this
paragraph.
L.
Lyons Industries, Inc.
M. Royal Baths Manufacturing Co.
N.
<Insert manufacturer's name>.
First list of manufacturers below is for solid-surface bar sinks.
O.
P.
Q.
R.
S.
T.
U.
V.
224100 - 27
Revere Sink.
Sterling; a Kohler company.
WhiteRock Corp.
<Insert manufacturer's name>.
Fixture:
Standard:
ASME A112.19.1/CSA B45.2 for enameled [cast-iron] [-steel]
lavatories.
Standard: ANSI Z124.3 for PMMA lavatories.
Standard: ANSI Z124.3 and ANSI/ICPA SS-1 for solid-surface lavatories.
Standard: ASME A112.19.3/CSA B45.4 for stainless-steel lavatories.
Standard: ASME A112.19.2/CSA B45.1 for vitreous-china lavatories.
Type: [Flat rim with ledge] [Self-rimming].
Overall Dimensions: <Insert dimensions>.
Bowl Dimensions: <Insert dimensions>.
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
224100 - 28
Retain one of five lists of manufacturers below. First list is for enameled cast-iron kitchen sinks.
A.
B.
C.
D.
224100 - 29
Fixture:
Metal Thickness:
dimension>.
Bowl:
1.
2.
Retain "Left Bowl," "Right Bowl," and "Center Bowl" subparagraphs as required for multibowl sinks.
H.
Left Bowl:
1.
2.
I.
Right Bowl:
1.
2.
J.
Center Bowl:
224100 - 30
0.4
0.5
0.6
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
0.2
224100 - 31
Fixture:
A.
B.
C.
D.
0.4
0.5
0.6
Copy "Laundry Trays" Paragraph below and re-edit for each type of plastic laundry tray required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each
laundry tray.
PRODUCT DATA SHEET 1 - Laundry Trays <Insert drawing designation>: Plastic laundry tray.
Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from
manufacturers listed or a comparable product from other manufacturers.
1.1
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
1.2
Gerber Plumbing Fixtures LLC does not manufacture a product complying with requirements of this
paragraph.
D.
Mustee, E. L. & Sons, Inc.
E.
Swan Corporation (The).
F.
Zurn Industries, LLC; Light Commercial Specialty Plumbing Products.
G.
<Insert manufacturer's name>.
1.3
Fixture:
A.
224100 - 32
Retain "Plastic" option in "Material" Subparagraph below or retain one or more of other options if a
specific material is required.
C.
D.
E.
F.
1.4
1.5
1.6
[Retain one of two lists of manufacturers below. First list is for general-duty, solid-brass faucets.
A.
B.
C.
D.
E.
F.
G.
224100 - 33
Retain second option in "Maximum Flow Rate" Subparagraph below for laundry-tray faucets.
1.6
Maximum Flow Rate: [2.0 gpm (7.5 L/min.)] [2.5 gpm (9.5 L/min.)] [4.0 gpm
(15 L/min.)] <Insert value> unless otherwise indicated.
1.7 Mixing Valve: [Single control] [Two-lever handle].
1.8 Backflow-Prevention Device for Hand Spray: [Required] [Not required].
1.9 Centers: [4 inches (102 mm)] [6 inches (152 mm)] [8 inches (203 mm)] [Single hole]
[Adjustable].
1.10 Mounting: [Deck] [Back/wall], [exposed] [concealed].
1.11 Handle(s): [Lever] [Knob] [Knob, nonmetallic] [Cross, four arm] [Wrist blade, 4
inches (102 mm)] [Elbow, 6 inches (152 mm)] [Not applicable].
1.12 Spout Type: [Rigid, solid brass] [Rigid, solid brass with wall brace] [Swing, round
tubular] [Swing, shaped tube] [Swing, solid brass] [Rigid gooseneck] [Swivel
gooseneck].
If retaining "laminar flow" option in "Spout Outlet" Subparagraph below, retain "Laminar-Flow, FaucetSpout Outlets" Article.
1.13 Spout Outlet: [Aerator] [Swivel aerator/spray] [Spray] [Laminar flow] [Plain end].
1.14 Drain: [Stopper with chain] [Grid] [Lift and turn].
SCHEDULE 13 - DISHWASHER AIR-GAP FITTINGS
PRODUCT DATA SHEET 0 - Dishwasher Air-Gap Fittings <Insert drawing designation>:
Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from
manufacturers listed or a comparable product from other manufacturers.
0.1
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
0.2
224100 - 34
Hoses: Rubber and suitable for temperature of at least 140 deg F (60 deg C).
A.
B.
Inlet Hose: 5/8 inch (16 mm) ID and [48 inches (1219 mm)] <Insert dimension>
long.
Outlet Hose: 7/8 inch (22 mm) ID and [48 inches (1219 mm)] <Insert
dimension> long.
224100 - 35
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
0.2
Retain one of two lists of manufacturers below. First list is for batch-feed disposers.
A.
B.
C.
D.
E.
F.
224100 - 36
Standards: ASSE 1008 and UL 430, and listed and labeled as defined in NFPA 70, by a
qualified testing agency, and marked for intended location and application.
General: Include reset button; wall switch; corrosion-resistant chamber with jamresistant, cutlery- or stainless-steel grinder or shredder; NPS 1-1/2 (DN 40) outlet; quickmounting, stainless-steel sink flange; antisplash guard; and combination cover/stopper.
Model: [Not applicable] [Sound-insulated chamber] [Sound-insulated chamber and
stainless-steel outer shell].
Motor: 115-V ac, 1725 rpm, [1/3] [1/2] [3/4] [1] hp with overload protection.
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
1.2
Retain one of two lists of manufacturers below. First list is for gooseneck spout with lever-handle, flowcontrol, hot-water dispensers.
RESIDENTIAL PLUMBING FIXTURES
224100 - 37
List of manufacturers below is for spout with twist-knob or push-button, flow-control, hot-water
dispensers.
F.
G.
H.
I.
J.
K.
1.3
1.4
1.5
1.6
Bowl:
224100 - 38
Retain first option in "Water Consumption" Subparagraph below unless special, low-consumption design
is required.
E.
F.
0.3
0.4
D.
Riser:
1.
2.
Copy "Water Closets" Paragraph below and re-edit for each type of flushometer-tank, vitreous-china
water closet required.
Insert number to complete drawing designation. Use these designations on Drawings to identify each
water closet. Do not use same designation as is used for another water closet in other Division 22
plumbing-fixture Sections. See Specification Coordination Checklist for other Sections specifying water
closets.
PRODUCT DATA SHEET 1 - Water Closets <Insert drawing designation>: Floor mounted, floor
outlet, close coupled (flushometer tank), vitreous china.
1.1 Basis-of-Design Product: Subject to compliance with requirements, provide Gerber
Plumbing Fixtures LLC; [UltraFlush] [Brianne] [Maurice], or comparable product by
one of the following:
Retain one of four lists of manufacturers below. First list below is for Sloan's "Flushmate" flushometertank, 1.0-gal./flush (3.8-L/flush) water closets.
A.
<Insert manufacturer's name>.
First list of manufacturers below is for Sloan's "Flushmate" flushometer-tank, 1.6-gal./flush (6-L/flush)
water closets.
B.
C.
224100 - 39
List of manufacturers below is for Briggs's vacuum-assist, flushometer-tank, 1.1-gal/flush or 1.6gal./flush (4.1 or 6-L/flush) water closets.
F.
1.2
Bowl:
A.
B.
C.
D.
Retain first option in "Water Consumption" Subparagraph below unless special, low-consumption design
is required.
E.
F.
1.3
1.4
D.
Riser:
1.
2.
224100 - 40
Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific
product or a comparable product from manufacturers listed. Retain option and delete insert note if
manufacturer's name and model number are indicated on Drawings.
0.2
0.3
0.4
0.5
0.6
224100 - 41
Supply Piping: Chrome-plated-brass pipe or chrome-plated-copper tube matching watersupply piping size. Include chrome-plated wall flange.
Stops: Chrome-plated-brass, one-quarter-turn, ball-type or compression stop with inlet
connection matching water-supply piping type and size.
A.
2.3
Risers:
A.
B.
C.
Size: [NPS 1-1/4 (DN 32)] [NPS 1-1/2 by NPS 1-1/4 (DN 40 by DN 32)]
[NPS 1-1/2 (DN 40)] for [bidets] [and] [lavatories].
Size: NPS 1-1/2 (DN 40) for [bar sinks] [kitchen sinks] [and] [laundry trays].
D.
E.
SCHEDULE 21 - GROUT
PRODUCT DATA SHEET 0 - Standard:
ASTM C 1107/C 1107M, Grade B, post-hardening and
volume-adjusting, dry, hydraulic-cement grout.
224100 - 42
PRODUCT DATA SHEET 2 - Design Mix: 5000-psi (34.5-MPa), 28-day compressive strength.
PRODUCT DATA SHEET 3 - Packaging: Premixed and factory packaged.
PART 3 - EXECUTION
SCHEDULE 0 - EXAMINATION
PRODUCT DATA SHEET 0 - Examine roughing-in of water-supply and sanitary drainage and vent
piping systems to verify actual locations of piping connections before plumbing-fixture
installation.
PRODUCT DATA SHEET 1 - Examine walls, floors, cabinets, and counters for suitable conditions
where fixtures will be installed.
PRODUCT DATA SHEET 2 - Proceed with installation only after unsatisfactory conditions have been
corrected.
SCHEDULE 1 - INSTALLATION
PRODUCT DATA SHEET 0 - Install plumbing fixtures level and plumb according to roughing-in
drawings.
PRODUCT DATA SHEET 1 - Install floor-mounted water closets on closet flange attachments to
drainage piping.
First paragraph below applies to counter-mounting fixtures such as lavatories and sinks.
PRODUCT DATA SHEET 2 - Install counter-mounting fixtures in and attached to casework.
PRODUCT DATA SHEET 3 - Install pedestal lavatories on pedestals and secured to wood blocking in
wall.
PRODUCT DATA SHEET 4 - Install water-supply piping with stop on each supply to each fixture to
be connected to water distribution piping. Attach supplies to supports or substrate within pipe
spaces behind fixtures. Install stops in locations where they can be easily reached for operation.
4.1
Exception: Use ball, gate, or globe valves if supply stops are not specified with fixture.
Comply with valve requirements specified in Division 22 Section "General-Duty Valves
for Plumbing Piping."
PRODUCT DATA SHEET 5 - Install tanks for accessible, tank-type water closets with lever handle
mounted on wide side of compartment.
PRODUCT DATA SHEET 6 - Install toilet seats on water closets.
RESIDENTIAL PLUMBING FIXTURES
224100 - 43
PRODUCT DATA SHEET 10 - Install disposer in outlet of each sink indicated to have a disposer.
Install switch where indicated or in wall adjacent to sink if location is not indicated.
PRODUCT DATA SHEET 11 - Install dishwasher air-gap fitting at each sink indicated to have air-gap
fitting. Install [in sink deck] [on countertop at sink] <Insert location>. Connect inlet hose to
dishwasher and outlet hose to disposer.
PRODUCT DATA SHEET 12 - Install hot-water dispensers in back top surface of sink or in
countertop with spout over sink.
PRODUCT DATA SHEET 13 - Set [bathtubs] [baths] [and] [shower receptors] in leveling bed of
cement grout.
Indicate on Drawings those lavatories and sinks that are required to be accessible.
PRODUCT DATA SHEET 14 - Install protective shielding pipe covers and enclosures on exposed
supplies and waste piping of accessible [lavatories] [and] [sinks]. Comply with requirements
in Division 22 Section "Plumbing Piping Insulation."
PRODUCT DATA SHEET 15 - Install wall flanges or escutcheons at piping wall penetrations in
exposed, finished locations. Use deep-pattern escutcheons if required to conceal protruding
fittings. Comply with escutcheon requirements specified in Division 22 Section "Escutcheons
for Plumbing Piping."
PRODUCT DATA SHEET 16 - Seal joints between plumbing fixtures, counters, floors, and walls
using sanitary-type, one-part, mildew-resistant silicone sealant. Match sealant color to fixture
color. Comply with sealant requirements specified in Division 07 Section "Joint Sealants."
SCHEDULE 2 - CONNECTIONS
Coordinate piping installations and specialty arrangements with schematics on Drawings and with
requirements specified in piping systems. If Drawings are explicit enough, these requirements may be
reduced or omitted.
PRODUCT DATA SHEET 0 - Connect fixtures with water supplies, stops, and risers, and with traps,
soil, waste, and vent piping. Use size fittings required to match fixtures.
224100 - 44
224100 - 45