Beruflich Dokumente
Kultur Dokumente
ZENOTEC
MATERIALS OVERVIEW
7/29/13 12:48 PM
THE MATERIALS
Table of contents
The Materials
Zenotec Zr Bridge
Zenotec Color Zr
Zenotec Wax
Zenotec Model
Zenotec NP
Zenotec Ti
Zenotec Ti pur
7/29/13 12:48 PM
This high quality zirconia material can be used for all types of indications from
the primary elements of telescopic crowns to 14-unit bridges. This material differs from
Benefits
a special manufacturing process, and results in an excellent fit, even with very large
restorations.
Physical properties
Biocompatible
Homogeneous, very fine grain
structure
Color
Density
Open porosity
0%
Indications
Vickers hardness
1,300 HV
Crushing strength
2.000 MPa
Flexural strength
E modulus
210 GPa
Fracture strength
7 MPa*m1/2
CTE
Composition
7/29/13 12:48 PM
matter: the zirconia frameworks are placed in the coloring solution and then
briey fixed by immersing in the specially developed Zenotec Color Fix. This
gives you a completely homogeneous edge-free coloring effect, with absolutely
no need for a liner. This allows you to save a great deal of time by working
much more efficiently. The dispensing with a liner gives the more translucent
appearance after veneering.
Indications
Zenotec Color Zr and Zenotec Color Fix are available in generous 250 ml
bottles, as well as in assortments which offer even greater convenience.
You have a choice of the Starter Set (shades A2, A3, A3.5, B2, B3, C2, C3
and D3) and the Add-on Set (shades Al, A4, B1, B4, C1, C4, D2 and D4). In
addition to the coloring and fixing solutions, the assortments come complete with
coloring jars, filter inserts and tweezers to make the handling of Zenotec Color Zr
even easier. The large coloring jars are suitable for large-span bridgework. These
accessories are also available separately.
7/29/13 12:48 PM
This transparent acrylic material is very easy to mill and gives excellent stability even with
large-span bridges. The material burns without trace and is especially suitable for use in
the lost material casting process but can also be used for pressing and over pressing.
The process provides a very fast and affordable method of testing the functionality and
fit of a restoration on the dental model.
Benefits
Very easy to mill
Best shape stability even for large-span bridges
Very good surface quality, especially for reproducing fissures
Crystal clear surface with outstanding translucence
Fully burns out
Low cost alternative for the manufacture of lost forms for the casting process
Physical properties
(at 23 C and 50 % relative humidity)
Raw density
1.19 g/cm3
E modulus
3300 mMPa
103 C
175 MPa
105 MPa
100 % PMMA
7/29/13 12:48 PM
Zenotec Wax
This new type of wax is extremely easy to mill and does not smear. It reduces milling
time, is easy on the extraction system, and helps to keep the machine clean. Thanks to
its low coefficient of expansion, even large-span bridges can be made without sacrificing
anything in terms of fit. The material nearly burns without trace and is therefore ideally
suited to making lost forms for the casting process, but can also be used for pressing
and over pressing.
Benefits
Very easy to mill
Does not smear during milling
Low coefficient of expansion for best shape stability and fit, even with large-span bridges
Nearly burns out without trace
Ideal alternative for manufacturing lost forms for the casting process
Good contrast
High melting point
High speed
No static build-up
Physical properties
Chemical composition
synthetic wax
Odor
odorless
100 130 C
Flash point
not applicable
Density
0.97 g /cm3
Solubility in water
insoluble
7/29/13 12:48 PM
Zenotec Model
Zenotec PU blanks are available for making CAD/CAM arch models which are virtually
unbreakable and keep their shape. These blanks are easy to mill and because the chips
are of uniform size, gentle on the extractor.
Benefits
Good stability
Virtually unbreakable
Low coefficient of thermal expansion
Vaporisable
Very easy to mill
Gentle on tools and the extraction system
High density, giving a smooth and uniform surface quality
Physical properties
Chemical composition
polyurethane
Density
1000 kg/m3
Crushing strength
45 50
Flexural strength
50 55
Coefficient of expansion
50 55 * 10-6 K-1
Shore D hardness
75 85
80 C
7/29/13 12:48 PM
Zenotec NP
Zenotec NP is a high quality CrCo alloy (type 3) for all REM applications. This industrially-produced material offers
a high degree of processing reliability and excellent physical properties, guaranteeing consistently high quality. In
addition, the CrCo alloy offers excellent resistance to corrosion and heat. Of course, Zenotec NP blanks are free
of nickel and beryllium and therefore biocompatible. The best esthetic results are obtained by veneering with our
Reex Dimension ceramic.
Benefits
Indications
Physical properties
Alloy type
Density
8.8 g/cm3
Vickers hardness
300 HV 5 /30
CTE
E modulus
210 GPa
330 MPa
Elongation
7%
Composition
Co 63 %, Cr 29 %, Mo 6 %, Mn Nb Si Fe
7/29/13 12:48 PM
Zenotec Ti
Zenotec Ti is made from a high quality titanium alloy (Ti 6AI 4V). This Grade 5 alloy has
exceptional physical and mechanical properties, such as high strength, which enables
Benefits
the fabrication of challenging restorations such as 14-unit bridges. The material also
proved its excellent biocompatibility it has been used successfully for many years
for hip joint implants and in the dental field for implant superstructures. The best
esthetic results are obtained by veneering with ceramic especially suited to titanium
substructures.
Intended purpose
Ti 6Al 4V alloy blanks for the manufacture of dental restorations with the aid of a
CAD/CAM system.
Indications
Physical properties
Alloy type
Density
4.43 g /cm3
Vickers hardness
350 HV 5 /30
CTE
Composition
930 MPa
900 MPa
Elongation
10 %
Melting point
7/29/13 12:48 PM
Zenotec Ti pur
Zenotec Ti pur is a high quality pure titanium (Grade 2) suitable for crown and bridge
work in both anterior and posterior regions. This material is known for its outstanding
physical properties and biocompatibility, in addition to it being very easy on cutting
tools. The best esthetic results are obtained by veneering with a veneering ceramic especially suited to titanium substructures.
Physical properties
Benefits
Alloy type
Density
4.51 g /cm3
Indications
Vickers hardness
150 HV 5 /30
CTE
Ti > 99 %
345 MPa
275 MPa
Elongation
20 %
Melting point
1.160 C / 2,120 F
7/29/13 12:48 PM
Telio CAD for Zenotec are cross-linked PMMA discs for the manufacture of temporary
crowns, bridges and implant restorations. They allow full-contour crowns and bridges to
be created that are comfortable to wear. As the maximum wear period is 12 months, the
material can also be used for the fabrication of therapeutic restorations in the treatment of
TMJ problems and in functional diagnostics.
Due to Telio CADs durable shade stability and lifelike uorescence, esthetically appealing
restorative results are achieved. The monochromatic discs are available in 6 LT shades (BL3,
A1, A2, A3.5 and B1). They can be processed in all Wieland Zenotec CAD/CAM milling
units. Due to the different thicknesses offered (16 mm and 25 mm), the discs provide great
exibility of use and are even suitable for higher implant restorations.
Telio is a comprehensive product system for temporary restorations. The chemical compositions and shades of the Telio materials are compatible with each other to ensure reliability
and exibility. After polishing, Telio CAD for Zenotec restorations are preferably cemented
with Telio CS Link or Telio CS Cem Implant. Prior to incorporation, they may be customized
Benefits
For long-term temporaries with
a wear period of up to 12 months
High biocompatibility
Shade stability and resistance to
plaque accumulation
Excellent polishability
Cost-effectiveness
Appealing lustre, esthetic appearance
Methacrylate-free, thus not irritating
to the gingiva and pulp
Convincing physical properties
Customizable with especially designed
Telio Lab LC materials
Coordinated range of luting materials:
Telio CS Link and Telio CS Cem Implant
with the light-curing stains and layering materials of Telio Lab LC range.
LT shades: BL3, A1, A2, A3, A3.5 and B1
Thicknesses: 16 mm, 25 mm
Physical properties
Flexural strength
130 10 Mpa
E modulus
190 5
< 28 g/mm3
Solubility in water
180 5 Mpa
Composition
10
7/29/13 12:48 PM
ZENOTEC mini
I V O C L A R V I VA D E N T G R O U P
LabShop
4-axis geometry
Automatic tool change and measurements
Zenotec mini measures only 15.7x16.5x14.9!
TM
Ask your Ivoclar Vivadent representative about the Zenotec mini today!
shopivoclarvivadent.com
I V O C L A R V I VA D E N T G R O U P
LabShop
Distributed by:
shopivoclarvivadent.com
ivoclarvivadent.com
7/29/13 12:48 PM