Beruflich Dokumente
Kultur Dokumente
IN
MODULE 1
1.
2.
3.
4.
5.
6.
7.
8.
MACHINE
DESIGN
13. Could be defined as simply push or pull.
A. work
B. force
C. inertia
D. power
14. The differential of shear equation is which
one of the following
A. bending moment of the beam
B. tensile strength of the beam
C. slope of the elastic curve
D. load of the beam
15. Gear used to transmit power at high
velocity ratios between non-intersecting
shaft that are usually but not necessarily at
right angle
A. helical gear
B. bevel gear
C. worm gear
D. spiral gear
16. The ratio of moment of the inertia of the
cross sections of the beam to the section
modulus.
A. equal to the radius of gyration
B. equal to the area of the cross section
C. measure of a distance
D. beam measure
17. Opposite direction parallel forces:
A. concurrent
B. coplanar
C. couple
D. non-coplanar
18. Which of the following is the structural class
of steel?
A. high speed steel
B. tool and die
C. low carbon
D. high carbon
A. working stress
B. operating stress
C. residual stress
D. shear stress
25. It is used to change rotary motion to
reciprocating motion:
A. helical gear
B. rack gear
C. worm gear
D. spur gear
26. It is recommended not to have a direct
drive and sprockets if the ratio of the teeth
exceeds ________ use two or more step
combination.
A. 10 times
B. 8 times
C. 5 times
D. 6 times
27. The motion of an object diminished/
decreased speed:
A. deceleration
B. all of the above
C. retarded motion
D. negative impulse
28. Most popular soldering material:
A. 10/80
B. 45/55
C. 50/50
D. 60/40
29. The following pertain to joining of metals
except:
A. welding
B. soldering
C. casting
D. brazing
30. Killed steel is always associated with:
A. silicon
B. manganese
C. phosphorous
D. sulfur
31. The usual ratio of water to soluble oil used
as cutting fluid:
A. 50% water to 50% oil
B. 2 water to 1 oil
C. 3 water to 1 oil
D. 4 to 80 water to 1 oil
32. The good deoxidizer in steel melting:
A. manganese
B. silicon
C. all of these
D. aluminum
33. Good stabilizer in stainless steel:
A. columbium
B. titanium
C. all of these
D. tantalium
34. What is the common cutting fluids used for
cutting materials?
A. all of these
B. water with soda or borax
C. light mineral oil
D. soluble oil
35. It is considered semi-solid lubricant:
A. all of these
B. lube oil
C. graphite
D grease
B. strain
C. Poissons ratio
D. strength
81. The maximum stress to which a material
may be subjected before failure occurs:
A. ultimate strength
B. ultimate stress
C. endurance limit
D. tensile stress
82. Hypoid gear is a special type of gear for:
A. worm gear
B. spur gear
C. herringbone gear
D. bevel gear
83. Considered a maximum safe center
distance of sprockets should be _______
inches. Very long center distance cause
centenary tension in the chain.
A. 70
B. 80
C. 60
D. 50
84. Cold working of steel plates makes the
metal:
A. tougher
B. more ductile
C. harder
D. more malleable
85. Recommended best cutting angle of drill for
work on steel or cast iron is _______ degrees
A. 48
B. 63
C. 59
D. 50
86. In shear pin or breaking pin design, we may
used the date experienced by link-belt for
1/8 inch to 1 pin and the breaking stress is
_______ ksi.
A. 40
B. 55
C. 50
D. 45
87. Deals only with the motion of bending
without reference is the forces that causes
them:
A. dynamics
B. kinetics
C. statics
D. kinematics
88. The property that characteristics a material
ability to be drawn into a wire:
A. ductility
B. thermal conductivity
C. tensile strength
D. endurance limit
7.
8.
9.
2.
3.
4.
5.
6.
A. sap wood
B. kiln dried wood
C. heart wood
D. core portion of wood
14. The gradual chemical reaction by other
substance such that metal is converted to
an oxide or other compounds:
A. corrosion
B. Cheaping
C. Rusting
D. Weathering
15. The center of gravity of a solid pyramid or
cone with a total height of H is:
A. H
B. 3/5 H
C. 1/3 H
D. H
16. Which do not belong to foundry or metal
casting shop?
A. shake-out machine
B. molding machine
C. coremaking
D. forging machine
17. What is the property of a material which
resists forces acting to pull the material
apart?
A. shear strength
B. tensile strength
C. torsional strength
D. compressive strength
C. IPS
D. AISI
51. Alloy steel known for its resistance to
corrosion, abrasion and wear that is usually
ideal for mill grinding of ore in cement and
concentrator application with molybdenum
to increase the depth hardening:
A. manganese chromium steel
B. chromium molybdenum steel
C. chrome-nickel-moly steel
D. manganese-moly steel
52. Commonly utilized/cheapest shaft material
available in the market with carbon content
of 0.28cto 0.34 % C.
A. SAE 4132
B. SAE 4320
C. SAE 1030
D. SAE 4130
53. In a pair of gears is it the plane that
contains the two axis, in single gear, it may
be any plane containing the axis and the
given point.
A. axial plane
B. pitch plane
C. normal plane
D. all of the above
54. Accident prevention is:
A. an association of employers,
organizations and individuals
B. the foremens responsibility just as much
as production
C. a job of a safety director
D. the responsibility of top management
55. Heating of metal above the critical
temperature and then cooling slowly usually
in the furnace to reduce the hardness and
improve the machinability is called:
A. normalizing
B. annealing
C. tempering
D. quenching
56. A type of welding whereby a wire or powder
from the nozzle of a spray gun is fused by a
gas flame, arc or plasma jet and the molten
particles are projected in a form of a spray
by means of compressed air or gas.
A. electro-slug welding
B. electro-beam welding
C. plasma-arc welding
D. metal spray welding
57. Killed steel is very much associated with:
A. manganese
B. sulphur
C. phosphorous
D. silicon
58. The concave portion of the tooth profile
where it joins the bottom of the tooth
space.
A. fillet curve
B. fillet
C. undercut
D. plane
59. The length of arc between the two sides of
a gear tooth on the pitch circle:
A. circular thickness
B. axial plane
C. helix angle
D. chordal angle
60. It is hardening treatment whereby a cast
metal is being heated to a very high
temperature then suddenly subjected to
rapid cooling to improve hardenability or
wear resistance is called:
A. normalizning
B. tempering
C. quenching
D. annealing
B. rusting
C. checking
D. fritting
73. A gear is one which is 90 deg that is the
pitch cone has become a plane:
A. angular gear
B. crown gear
C. miter gear
D. spiral bevel gear
74. A machine used for the testing of very thin
steel or surface layers:
A. Charpy test
B. Izod test
C. Description
D. Rockwell superficial
75. A cone formed by elements which are
perpendicular to the elements of the pitch
cone at the large end:
A. cone distance
B. back cone
C. root cone
D. cone center
76. The temperature above which the alloy I
liquid and will run:
A. melting point
B. flow point
C. pour point
D. liquidus
77. A weld made to hold the parts of a
weldment in proper alignment until the final
welds are made:
A. butt weld
B. tack weld
C. fillet weld
D. full fillet weld
78. Is used to enable milling machine to take
climb milling cuts:
A. helical driving mechanism
B. spindle
C. read out
D. backlash eliminator
79. The total amount of permanent extension of
the gage length measured after the
specimen has fractured and is expressed as
percentage increase of the original gage
length:
A. elongation
B. strain
C. stress
D. elastic limit
80. It refers to any layer or deposit of
extraneous material on a heat-transfer
surface:
A. low line
B. pressure drop
C. fouling
D. scaling
81. Steels containing large amounts of mild
nickel and chromium:
A. carbon steel
B. stainless steel
C. alloy steel
D. cast steel
82. The corrosion of iron or iron-base-alloys:
A. rusting
B. crazing
C. chalking
D. fritting
D. rectangle
95. The follower reciprocates or oscillates in a
plane perpendicular to the axis of rotation
of the cam:
2.
A. spindle-nose tooling
B. milling machine vise
C. vertical milling attachment
D. milling machine arbors
A. cam curves
B. cylindrical cam
C. tangential cam
D. radial cam
96. Impacts of reciprocating motion to a singlepoint cutting tool:
3.
4.
97. A joint between two overlapping members
in which the overlapped edge of one
member is welded with a fillet weld:
5.
7.
6.
A. stress
B. elasticity
C. strain
D. tensile strength
A. dividing head
B. slotting attachment
C. circular pitch
D. circular milling arrangement
8.
9.
D. lathe machine
C. sulfur
D. phosphorous
26. Which of the following is not a classification
of iron ore:
A. siderite
B. hematite
C. sulfurite
D. magnetite
27. The ability of metals to stand loads without
breaking down is:
A. strain
B. stress
C. elasticity
D. strength
28. Herringbone gears are gears which:
A. do not operate on parallel shafts
B. have line of contact between the teeth
C. tend to produce end thrust on the shaft
D. consists of two left handed helical gears
29. In general, the design stress and factor of
safety are related as follows:
A. Design = ultimate stress divided by
factor of safety
B. Design = ultimate stress times factor of
safety
C. Ultimate = stress factor for safety
divided by design stress
D. factor of stress = design stress divided
by ultimate stress
30. The internals stresses existing in a welded
connection are:
A. relieved by x-ray analysis
B. may be relieved when weld is peened
C. not relieved when the weld is peened
D. not relieved by heat treatment
31. In the usual spur gearing the:
A. pitch circle and base circle are the same
B. working depth includes the clearance
C. tooth outline are always cycloidal curves
D. tooth outline are usually involute curves
D. 3
47. The ratio of Bulk modulus to shear modulus
for Poissons ratio of 0.25 will be equal to:
A. 3/2
B. 5/6
C. 1
D. 6/3
A. same
B. half
C. one-third
D. two-third
53. Select the one that has no unit:
A. Kinematic viscosity
B. Surface tension
C. Bulk modulus
D. Strain
54. When a part is constrained to move and
heated, it develops:
A. principal stress
B. tensile stress
C. compressive stress
D. shear stress
55. The tensile stress of a material is given by:
A. Maximum load during test over Original
cross-sectional area
B. Average load during test over Original
cross-sectional area
C. Maximum load during test over Area at
the time of fracture
D. Average load during the test over Area at
the time of fracture
56. The size of hole that is drilled in plates for
riveting is:
A. equal to the diameter of rivet shank
B. slightly smaller than the diameter of rivet
shank
C. 1.5 to 2 mm smaller than the diameter of
rivets of 25 mm and above size
D. 1.5 to 2 mm larger than the diameter of
the rivet for rivets 25 mm and above size
57. The horsepower that can be transmitted by
a shaft 60 mm diameter at 180 rpm with
permissible shear stress of 850 kg/cm2 shall
be approximately:
A. 30-35
B. 35-50
C. 50-60
D. 60-85
58. A column is called short column when:
A. the length is more than 120
B. Slenderness ratio is more than 120
C. The length is less than 8 times the
diameter
D. the slenderness ratio is more than 32
D. 1 N/mm2
70. The value of shear stress changes is
induced in the shaft because of the applied
couple that:
A. From maximum at the center to zero at
the circumference
B. From zero at the center to maximum at
the circumference
C. From maximum at the center to
minimum at the circumference
D. From minimum at the center to
maximum at the circumference
71. In the design of pulley, key and shaft:
A. All three are designed for same strength
B. Key is made weaker link
C. Pulley is made weaker
D. Shaft is made weaker
D. Cylindrical pair
A. Rolling
B. Pitching
C. Steering
D. All of the above
Module 4
1.
2.
3.
4.
5.
6.
7.
A. cps
B. gram
C. gm-cm-cps
D. gm-cm
A. Expansion Valve
B. Slide Valve
C. Flywheel
D. Governor
A. Loss of power
B. Difference between the angular velocities
of two pulleys
C. Difference between the velocities of two
pulleys
D. Difference between the linear speed of
the rim pulley and the belt on it.
94. In case of flat belt drive the length of belt in
case of:
A. Clinograph
B. Trisquare
C. Graphometer
D. Pantograph
9.
8.
A. Static load
B. Impact load
C. Dynamic
D. Completely reversed load
B. Composite material
C. Homogeneous material
D. Heterogeneous material
44. Rankine formula is valid up to slenderness
ratio of:
A. Major diameter
B. Pitch diameter
C. Minor diameter
D. None of the above
bearings
are
A. Turning
B. Bolting
C. Casting
D. Cold heading
27. The blow of pressure of a safety valve is:
A. slightly more than atmospheric pressure
B. half of the boiler working pressure
C. equal to boiler working pressure
D. 106 % of boiler working pressure
28. In case of a knuckle joint the pin is most
likely to fail in:
A. compression
B. shear
C. tension
D. double shear
29. Splines are used when:
A. the power to be transmitted is low
B. the power to be transmitted is high
C. the torque is high
D. axial relative motion between the shaft
and hub is necessary
30. Splined shafts are generally used in:
A. machine tools
B. aircraft
C. bicycles
D. automobiles
31. Which key normally used in wrist watch?
A. kennedy key
B. tangent key
C. sunk key
D. none of the above
26. Steel
balls
for
manufactured by:
A. 80
B. 150
C. 60
D. 120
47.
are
generally
A. lead angle
B. pitch angle
C. helix angle
D. pressure angle
51. The type of cam used for low and moderate
speed engines is generally:
A. Harmonic
B. Tangent
C. involute
D. Flat
52. The form coefficient of a spring is:
A. The load/unit deflection
B. Load/spring area
C. Ratio of coil diameter to wire diameter
D. Its capability of store energy.
53. Coriolis component of acceleration is found
in:
A. Four bar mechanism
B. Lower pair
C. Mechanism of steam engine
D. Wit worth quick return motion
54. Cold working materials:
A. Increase the fatigue strength
B. Decreases the fatigue strength
C. Does not change fatigue strength
D None of the above
55. A Babbitt is:
A. 6 mm
B. 12 mm
C. 8 mm
D. 3 mm
69. A rolled steel that flat designated as 50 ISF
8 means:
A. the flat is 50 mm and 8 mm thick
B. the flat is 50 mm wide and 8 mm thick
C. The flat has cross section 50 sq. Mm and
width 8 mm
D. The flat has cross section 50 sq. Mm and
depth 8 mm
70. The column splice is used for increasing:
A. Strength of the column
B. Cross-sectional area of the column
C. Length of the column
D. All of the above
71. Zero axial thrust is experienced in:
A. Helical gears
B. Spiral gears
C. Herringbone gears
D. Bevel gears
72. In order to realize the advantage of fluid
friction, it is essential to have:
A. Parallel oil film in bearing
B. Converging oil film
C. No oil film
D. Diverging oil film
73. A shaft rotating in anticlockwise direction at
slow speed inside a bearing will be:
A. At bottom most of bearing
B.Towards left side of bearing making metal
to metal contact
C. Towards left side of bearing and making
no metal contact
D. None of the above
74. Points of arrest of iron correspond to:
A. Stages at which allotropic forms change
B. Stages at whic further heating does not
increase temperature for sometime
C. Stages at which properties do not change
with increase in temperature
D. There is nothing like points of arrest
75. Delta iron occurs at temperature of:
A. Room temperature
B. Above melting point
C. Between 1400 to 1539C
D. Between 1000C to 1400C
occurs
when
part
is
A. compressive stress
B. tensile stress
C. torsion
D. fluctuating stress
C. lead
D. angle of thread
9.
A. 40-60 MPA
B. 150-180 MPA
C. 840-1500 MPA
D. 1500-1650 MPA
91. In carbon steel castings:
MODULE 5
The property of material that relates
the lateral strain to longitudinal strain
A. Stress
B. Strain
C. Poissons Circle
D. Endurance Limit
1.
2.
95. Which one is different from the remaining:
A. cyaniding
B. nitriding
C. flame hardening
D. electroplating
Also
called
eccentrically
bearing is ___________.
A. full bearing
B. offset bearings
C. partial bearings
D. fitted bearings
A. austenite
B. pearlite
C. all of the above
D. martensite
A. couple
B. centroids
C. equilibrium
D. vector
loaded
3.
96. The hardness of steel increases if it
contains:
A. five-bar linkage
B. four-crank braces
C. three-crank linkage
D. four-bar linkage
31. Used to change rotary motion
reciprocating motion _______.
to
A. rack gears
B. hypoid gears
C. helical gears
D. herringbone gears
32. The effective face width of a helical
gear divided by the gear pitch.
A. Approach ratio
B. Arc of action
C. Arc of recess
D. Face overlap
33. Pitch diameter less the diameter of the
roller chain is equal to:
A. top land
B. bottom diameter
C. addendum
D. inside diameter
34. Generally applied on speed reducer
due to large speed ratio
A. bevel gears
B. helical gears
C. worm gears
D. hypoid gears
35. If shaft is specified as ~diameter 2.00
max and 0.99 min in diameter then
the 0.010 could be defined as
_________.
A. allowance
B. fit
C. variance
D. tolerance
36. A material plane was subjected to a
load. When the load was removed, the
strain disappeared. From the structural
change, which of the following can be
considered about this material?
A. it has a high modulus of elasticity
B. it does not follow Hookes Law
C. it is plastic
D. it is elastic
37. Helix angle in the range of _______
degrees is recommended for wide face
helical gears.
A. less than 15
B. less than 20
C. 20 to 35
D. 20 to 22
49. Manganese
Steel
designation, SAE _______.
A. tolerance
B. fits
C. variance
D. allowance
A. 13xx
B. 10xx
C. 11xx
D. 8xxx
A. root circle
B. fillet radius
C. fillet curves
D. fillet
A. shear stress
B. stresses
C. compressive stress
D. strain
A. a measure of distance
B. equal to the radius gyration and
compression
C. multiplied by the bending moment
D. equal to the area of the cross-section
and tension
standard
is
not
C. 26 to 28
D. 18 to 24
A. 3.85 % Ni
B. 4 % Ni
C. 3.25 to 3.75 % Ni
D. 3.84 % Ni
A. plasticity
B. malleability
C. homogeneity
D. all of these
A. working stress
B. residual stress
C. simple stress
D. combined stress
A. 92xx
B. 5xxx
C. 3xxx
D. 11xx
A. Nickel
B. aluminum oxide
C. silicon base alloys
D. iron oxide
A. aluminum
B. manganese
C. silicon
D. chromium
A. aluminum
B. cast iron
C. steel material
D. wrought iron
A. elasticity
B. strength
C. plasticity
D. strain
75. Shafts are readily available in the
market are made in many ways and
wide variety of material composition. It
is likely be cold drawn carbon steel in
size smaller than _______ inches
diameter.
A. 3.75
B. 4
C. 5
D. 5 1/2
76. Plain
carbon
designation, SAE
steel
standard
A. 6xxx
B. 13xx
C. 10xx
D. 2xxx
of
polymer
can
be
A. furnace smelting
B. normalizing
C. crystallization
D. shot peening
78. The difference between cast steel and
cast iron.
A. all of these
B. cast steel has usually less than 1%C
while cast iron has 2% or 3.6% carbon
range
C. cast iron has lower strength, more brittle
and has lower ductility than cast steel.
D. iron is usually the initial product after
purifying iron ore then further processing by
removal of more impurities and carbon
content to be able to produce steel grade.
79. It is general practice to use the
following allowable stresses, 400 psi
for main transmitting shaft, short
shafts and countershaft. For lineshaft
carrying pulley it is ____ psi.
A. 7800
B. 7000
C. 6000
D. 6500
A. pyrite
B. austenite
C. all of these
D. cementite
A. reaming
B. soot facing
C. tapping
D. broaching
A. 0.50% to 0.90%
B. all of these
C. 0.45 to 0.48%
D. 0.96 to 0.97%
72. Principal
plane.
stresses
occur
on
these
1.
2.
A. 95
B. 98
C. 90
D. 92
A. 2.26
B. 1
C. 1
D. 2.59
3.
A. thimble
B. head screw
C. spindle
D. anvil
88. To avoid brittleness of weld or the
residual stress in the welding it is
normally stress relieved of ______.
A. normalizing
B. tempering
C. flame hardening
D. annealing
89. Steel with certain % of carbon
maximum can readily be welded by all
process and the resuling strength of
the portion welded is as strong as the
base material.
5.
99. Big
chain
sprocket
wheels
are
designed
with
spokes/arms
are
generally elliptical in cross section with
major axis _____ times the minor axis.
6.
A. 0.020
B. 1.010
C. 1.012
D. 0.150
7.
A. 2
B. 2
C. 1
D. 3
A. 0.15%C max
B. 0.35%C max
C. 0.25%C max
D. 0.30%C max
100. Molybdenum
designation, SAE
A. 88xx
B. 48xx
C. 40xx
D. 46xx
steel
standard
8.
A. silicon
B. aluminum
C. zinc
D. manganese
9.
A. axial plane
B. involute
C. arc of recess
D. arc of action
A. 80%
B. 1/3
C. 90%
D. 3/8
4.
87. The
following
are
parts
micrometer caliper except for
B. 35 to 50
C. 25 to 30
D. 15 to 20
MODULE 6
A. 60
B. 45
C. 40
D. 48
A. tolerance class
B. crest truncation
C. crest clearance
D. tolerance limit
A. vector
B. resultant
C. component of forces
D. resolution
13. __________ is the process necessary to
reduce the brittleness in alloy steel.
A. martempering
B. carburizing
C. normalizing
D. tempering
14. The welded joints permit placing the added
metal exactly where needed and produce
an integral structure which can develop
_____% efficiency on any thickness section
specially for mild metal materials.
A. 95%
B. 85%
C. 100%
D. 90%
A. overloading
B. jamming
C. all of these
D. overheating
16. __________ forces means when their lines of
action can be extended to meet to one
point.
A. Concurrent
B. centroids
C. collinear
D. resultants
A. 2%
B. 3%
C. 1%
D. 0%
A. sharp crest
B. sharp root
C. root apex
D. all of these
A. allowance
B. bottom land
C. top land
D. backlash
A. aluminum bronze
B. manganese
C. copper
D. bronze
27. Should two equal and opposite collinear
forces is added to the forces already in
equilibrium, which of the statement is true?
A. Unbalanced of moment is maintained
B. Equilibrium is disturbed
C. Equilibrium is maintained
D. It creates an unbalanced situation
A. Mn Hadfield steel
B. Chrome-moly steel
C. Stainless steel
D. High chrome steel
A. 3050
B. 4500
C. 7000
D.10000
30. The distance between rivet centers nearest
each other in adjacent rows is called
_________,
of
dimension
the
is
A. intolerance fits
B. deviation
C. allowance
D. tolerance
20. Molybdenum-chromium-nickel
designation.
A. Pitch
B. Back pitch
C. Margin
D. Diagonal pitch
31. The purpose of lubrication is mentioned
EXCEPT:
steel
A. SAE 48xx
B. SAE 43xx
C. SAE 56xx
D. SAE 46xx
21. __________ is also called strain hardening.
A. Cr
B. FeN
C. Cobalt
D. Mn
A. offset bearing
B. full bearing
C. centrally loaded bearing
D. Babbitt bearing
A. work hardening
B. quenching
C. annealing
D. normalizing
19. Permissible
variation
manufactured/machined
called:
D. collinear forces
34. For stable equipment foundation, the total
combined engine, driven equipment and
foundation center of gravity must be kept
below the foundations to that usually about
_____ times the usual total combined weight
of the machinery it is supposed to support.
A. 3 to 4
B. 3 to 7
C. 2 to 4
D. 3 to 5
35. All associated with
specification EXCEPT:
standard
materials
color
used
in
A. silver gray
B. aluminum gray
C. bare
D. white
39. Not part and in fact should not be used in
the steel melting process.
A. Coke
B. Silicon
C. Zinc
D. Aluminum
40. It is rigid piece which serves to transmit
force from a piece to another piece or to
cause/control motion.
A. follower
B. crank
C. cam motion
D. link
41. Type of bolt commonly used in the
construction that is threaded in both ends.
A. Stud bolt
B. Acme thread
C. Hex bolt
D. Square threaded bolts
42. Ten normal helix angles in helical gears is
recommended in the range of _____
degrees.
A. less than 18
B. 20 to 35
C. 15 to 25
D. 20 to 30
43. The ratio of stress acting on an elastic
substance to the decrease in volume per
unit volume.
A. Bulk modulus
B. Modulus of resilience
C. Elastic limit
D. Modulus of elasticity
44. Rule of thumb in calculating the equipment
foundation mass should be _____ times the
weight of the machinery it is suppose to
support.
A. 3-5
B. 3-6
C. 3-9
D. 2-4
A. groove joint
B. fillet joint
C. edge joint
D. corner joint
decreased
increasing
A. aluminum
B. p-type semiconductors
C. metals
D. n-type semiconductors
48. Cast iron flywheels are commonly designed
with a factor of safety of:
A. 10 to 13
B. 10 to 12
C. 10 to 14
D. 8 to 13
49. Stress relieving also __________ for the
purpose of reducing the internal stresses of
steel material/metal.
A. Tempering
B. Normalizing
C. All of these
D. Annealing
50. A ridge of uniform section in the form of a
helix cut around the circumference of a
cylinder and advancing along the axis.
A. Thread roots
B. Helix thread
C. Screw threads
D. Chamfers
51. Martensite (stainless steel) contains 4 to
26% Cr and a maximum of _____% nickel.
A. 2.5
B. 3.25
C. 3.5
D. 2.0
52. The design of stress and factor of safety are
related in the following manner:
A. Design stress = ultimate stress/factor of
safety
B. Ultimate stress = factor of safety/design
stress plus concentration factor
C. Factor of safety = design stress/ultimate
stress
D. Design stress = factor of safety/times
stress concentration factor
53. The material that can cut/wear hardest
substance subjected to:
A. Carbide
B. Abrasive
C. Tungsten
D. Vanadium
54. The resulting force that replace two or more
forces acting together.
A. Vector
B. Couple
C. Resultant
D. Equillibrant
A. Shear strength
B. Ultimate strength
C. Compressive strength
D. Elastic limit
agnet
is
steel
elements
to
torsion
A. Tensile strength
B. Compressive stress
C. Shearing stress
D. Moment
73. The deflection of a beam is:
A. Directly proportional to the modulus of
elasticity and moment of inertia
B. Inversely proportional to the modulus of
elasticity and length of the beam cube
C. Inversely proportional to the modulus of
elasticity and moment of inertia
D. Directly proportional to the load imposed
and inversely proportional to the length
squared
74. The differential of the shear equation is
which of the following?
A. Load of the beam
B. Tensile strength of beam
C. Bending moment of the beam
D. Slope of the elastic curve
75. A vertically loaded beam, fixed at one end
and simply supported at the other is
indeterminate to what degree?
A. First
B. Second
C. Third
D. Fourth
76. A thin walled pressurized vessel consist a
right circular cylinder with flat ends. Midway
between the ends the stress is greater in
what direction?
A. Longitudinal
B. Circumference
C. Radial
D. At an angle of 45 to the longitudinal
77. The bending moment at a section of a
beam is derived from the:
A. Sum of the moments of all external
forces on one side of the section
B. Difference between the moments on one
side of the section and the opposite side
C. Sum of the moments of all external
forces on both sides of the section
D. Sum of the moments of all external
forces between supports
78. The stress concentration factor:
A. is a ratio of the average stress on a
section to the allowable stress
B. Cannot be evaluated for brittle materials
C. is the ratio of the areas involved in a
sudden change of cross section
D. is the ratio of the maximum stress
produced in a cross section to the average
stress over the section
79. Poissons ratio is the ratio of the:
A. Unit lateral deformation to the unit
longitudinal deformation
B. Unit stress to unit strain
C. Elastic limit to the proportional limit
D. Shear stress to compressive stress
80. Hookes Law for an isotopic homogenous
medium
experiencing
one-dimensional
stress is:
A. Stress = E (strain)
B. Strain = E (Stress)
C. Force (Area) = E (Change
length/length)
D. Strain energy = E (Internal energy)
in
96. Intrinsic
silicon
becomes
extrinsically
conductive, with electrons as majority
carriers, when doped with which of the
following?
A. Aluminum
B. Antimony
C. Boron
D. Germanium
97. Steels can be strengthened by all of the
following EXCEPT:
A. Annealing
B. Quenching and tempering
C. Work hardening
D. Grain refinement
98. If 1080 steel (0.80 wt. % C) is annealed by
very low cooling from 1000C (1832F) to
ambient temperature, its microstructure will
consist almost solely of:
A. Austenite
B. Bainite
C. Cementite
D. Pearlite
metallic
crystal
of the following
cured
A. Sand-gravel ratio
B. Fineness modulus
C. Absolute volume
D. Water-cement ratio
MODULE 7
1.
about
5.
6.
A. 10 mm
B. 30 mm
C. 20 mm
D. 60 mm
13. In case of knuckle joint the pin is most likely
to fail in:
A. Compression
B. Shear
C. Tension
D. Double shear
14. In case of sunk key:
A. The key is cut in both shaft and hub
B. The key way is cut in hub only
C. The key way is cut in shaft only
D. The key is helical along the shaft.
15. Splines are used when:
A. The power to be transmitted is low
B. The power to be transmitted is high
C. The torque is high
D. Axial relative motion between motion
between shaft and hub is necessary
16. Splined shafts are generally used in:
A. Machining tools
B. Aircraft
C. Bicycles
D. Automobiles
17. Which key normally used in wrist watch?.
A. Kennedy key
B. Tangent key
C. Sunk key
D. None of the above
8.
9.
A babbit is:
A. A eutectic of iron and iron phosphide
B. A gadget for measuring volume
C. A measure of magnetic induction
produced in a material
D. Antimony bearing lead or tin alloy
A. Turning
B. Rolling
C. Casting
D. Cold heading
11. The blow off pressure of a safety valve is:
A. Slightly more than atmospheric pressure
B. Half of the boiler working pressure
C. Equal to boiler working pressure
D. 106% of boiler working pressure
12. A foundation bolt with a circular end is
secured to the floor by means of a steel
A. 2.5 HP
B. 5.0 HP
C. 4.0 HP
D. 3.0 HP
25. For butt welding of two plates each of which
is 25 mm thick, the best process would be :
A. TIG welding
B. MIG welding
C. Gio welding
D. Electro slag welding
26. The compression members tend to buckle
in the direction of:
A. Axis of load
B. Perpendicular to the axes load
C. Minimum cross section
D. Least radius of gyration
27. The diameter of a washer is generally:
A. Equal to the diameter of bolt
B. Slightly more than the diameter of the
bolt
C. Slightly less than the diameter of the bolt
D. Of any size that suits the application
28. If the lead angle of a worm is 22 1/2 than
the helix angle will be:
A. 45
B. 67
C. 22
D. None of the above
A. Clad material
B. Composite Material
C. Homogenous material
D. Heterogeneous material
30. Rankine formula is valid up to slenderness
ratio of:
A.
B. 150
C. 50
D. 120
31. Slenderness ratio of a column is:
A. Shaft diameter over shaft length
B. Column height over column cross section
C. Column height over least dimension of
column cross-section
D. Length of strut over least radius of
gyration
D. d3/4
A. Helical gears
B. Spiral gears
C. Herringbone gears
D. Bevel gears
59. In order to realize the advantages of fluid
friction, it is essential to have:
are
generally
A. Lead angle
B. Pitch angle
C. Helix angle
D. Pressure angle
38. The type of cam used for low and moderate
speed engines is generally::
A. Harmonic
B. Tangent
C. Involute
D. Flat
A. Parallel
B. Converging
C. No oil film
D. Diverging oil film
A. Room temperature
B. Above melting point
C. Between 1400 and 1539C
D. Between 1000 and 1400C
63. Gamma
iron
temperature:
exists
at
following
A. Room temperature
B. Near melting point
C. Between 1400 and 1539C
D. Between 910 and 1400C
64. Ferromagnetic
alpha
temperature range of:
iron
exists
in
A. Below 732C
B. 700-910C
C. 1000-1440C
D. 1400-1539C
65. Paramagnetic iron changes to gamma iron
at:
A. 970C
B. 910C
C. 440C
D. 1639C
66. Fatigue failure
subjected to:
occurs
when
part
is
A. Compressive stress
B. Tensile stress
C. Torsion
D. Fluctuating
67. A body having identical properties all over
is called:
A. Homogenous
B. Elastic
C. Ductile
D. Isentropic
68. If
a
material
recovers
its
original
dimensions, when the load is removed, it is
called:
A. Plastic
B. Elastic
C. Brittle
D. Annealed
69. The behavior of metals where in strength of
a metal is increased and the ductility is
decreased on heating at a relatively low
temperature after cold working is called:
A. Twinning
B. Clustering
C. Screw dislocation
D. Strain aging
A. Sintering
B. Granulation
C. Deposition
D. Precipitation
82. Which one is different from the remaining?
of
steel
can
be
A. Magnesium alloys
B. Chromium
C. None of the above
D. Titanium alloys
steel
increases
if
it
A. Austenite
B. Pearnite
C. All of the above
D. Martensite
84. The presence of sulfur in pig iron makes:
A. It easily machinable
B. It hard
C. It brittle
D. The casting unsound
85. Compressive strength of gray cast iron is
of the order of:
A. 3-5
B. 7-10
C. 15-22
D. 5-7
of
powerful
and its
ability of
chemical
A. Silicon
B. Aluminum
C. Carbon
D. Sulphur
77. Tensile strength of common varieties of cast
iron is in the range of:
A. 40-60 MPa
B. 150-180 MPa
C. 840-500 MPa
D. 1500-1650 MPa
A. Cyaniding
B. Nitriding
C. Flame hardening
D. Electroplating
83. The hardness
contains:
A. Taper bores
B. Cylindrical bores
C. Spherical bores
D. Screw threads
13. Choose the one that will have the highest
cutting speed.
MODULE 8
1.
The phenomenon
associated with:
of
weld
decay
is
A. Brass
B. Manganese steels
C. Aluminum alloys
D. Stainless steels
2.
3.
4.
A. Cast iron
B. Tool steel
C. Brass
D. Aluminum
5.
6.
A. Process industry
B. Structural work
C. Heavy duty
D. Electronic industry
18. Unlike materials or materials of different
thickness can be butt welded by:
A. Control of pressure and current
B. Adjusting time duration of current
C. Adjusting initial gap
D. All of the above
A. Thickness of plate
B. Voltage across the plate
C. Size of the electrode
D. Length of welded portion
A. Thermoplastics
B. Phenolics
C. All of these
D. Thermosetting plastics
8.
A. Welding electrode
B. Filler metal
C. Shield
D. Welding defect
31. A is:
A. A tool used in mould repairing
B. A process of cleaning castings
C. A chemical that is added to molten
materials for sound castings
D. A vertical passage through the cope
32. What is a gate?
9.
welding,
the
A. Gas welding
B. Arc welding when straight polarity is
used
C. Arc welding when reverses polarity is
used
D. Welding stainless steel
pressure
D. Centrifugal blower
47. A collimated light
producing heat in:
35. Tumbling is done so as to:
beam
is
used
for
A. MIG welding
B. TIG welding
C. Plasma welding
D. Laser welding
is
not
an
angle
A. Bevel protector
B. Sine bar
C. Combination square
D. Angle iron
40. Diatometer is used to find out which
property of moulding sand:
A. Permeability
B. Hot strength
C. Fineness
D. Moisture content
A. It is an automatic machine
B. It is a mass production machine
C. Semi-skilled operators can be employed
D. Operations is completed in one stroke
A. RPM of engines
B. Rotation of shafts
C. Twists due to torque applied on shafts
D. Flow of liquids and gases
one
that
is
gear
finishing
A. Gear shaving
B. Gear shaping
C. Gear hobbing
D. Gear milling
A. Negligible
B. Low
C. High
D. Very high
44. Hot wire Anemometers are generally for:
A. Measuring pressure of fluids
B. Measuring velocity of air stream
C. Measuring temperature of moving fluid
D. Measuring thermal conductivity of solids
A. Zero
B. Minimum or maximum
C. Maximum
D. Minimum
62. The ultimate tensile stress of mild steel as
compared to its ultimate compressive stress
will be:
A. Same
B. More
C. Less
D. More or less depending on other factors
63. Percentage
reduction
of
area
while
performing tensile test on cast iron may be
of the order of:
A. 50%
B. 25%
C. 0%
D. 15%
A. Die casting
B. Pressed casting
C. Gravity casting
D. Continuous casting
46. During
MIG
welding
the
transformed in the form of:
A. A straight line
B. A parabola
C. A sudden break
D. An irregular curve
A. Unit stress
B. Bulk
C. Modulus of rigidity
D. Modulus of elasticity
A. 3/2
B. 5/6
C. 1
D. 6/3
51. Drossing
39. Select the one that
measuring device.
A. 1
B. 2
C. 2.5
D. 3
metal
is
A. 2
B. 2/3
C. 3/2
D. 58. When a solid cube is subjected to equal
normal forces of the same type on all its
faces. The ratio of the volumetric
strain/linear strain along any of the three
axes will be equal to:
A. Torsional loads
B. Axial compressive loads
C. Axial tension loads
D. Transverse loads
85. If the areas of cross-sections of square and
circular beams are same and both are put
to equal bending moments, then the correct
statement is:
A. The circular beam is more economical
B. The square beam is more economical
C. Both the beams are equally strong
D. Both the beams are equally economical
86. The Biflar suspension method is used to find
out:
A. Position of balancing weights
B. Centripetal acceleration
C. Natural frequency of vibration
D. Moment of inertia
endurance
C. Grain growth
D. Cold working
10. Which of the following ropes will be most
flexible?
A. 6 x 19
B. 6 x 7
C. 8 x 19
D. 6 x 37
11. Muntz metal contains:
A. Copper-nickel
B. Copper-zinc
C. Copper-aluminum
D. None of these
1.
MODULE 9
Vickers, Knoop and Brinell are all names of:
A. Nobel prize in winners in metallurgy
B. Thermodynamic constants
C. Hardiness test
D. Magnetic constants
2.
3.
4.
6.
7.
8.
9.
A. Slip
B. Shear
C. Creep
D. Bending
13. Honing is used:
A. To remove small amount of metal
B. To correct axial run-out of bore
C. To correct out-of-roundness of a bore
D. On surfaces brought to high degree to
surface finish
14. A special metal formed when two or more
metals are melted together.
A. Alloy
B. Compound
C. Titanium
D. Brass
5.
steel
contains
A. SAE 2340
B. SAE 4230
C. SAE 5240
D. SAE 1230
28. Splines are used when:
A. The power of be transmitted is high
B. The torque is high
C. The speed is high
D. Axial relative motion between shaft and
hub is necessary
29. Instrument used to analyze the composition
of metals:
A. Spectrometer
B. Radiometer
C. Profilometer
D. Ultimate analyzer
30. An impact test is used to test a metal for:
A. Toughness
B. Strength
C. Ductility
D. Hardness
31. Poissons ratio is the ratio of the:
A. unit lateral deformation to the unit
longhitudinal deformation
B. Unit stress to unit strain
C. Elastic limit to proportional limit
D. Shear strain to compressive strain
32. Creep is the term used in referring to the:
A. Elongation before yield point
B. Maximum stress of brittle materials
C. Fatigue limit of ductile materials
A. Clearance
B. Variation
C. Tolerance
D. Deviation
44. Heating or cooling of steel that preduces a
rounded form of carbide:
A. Normalizing
B. Embrittleness
C. Spheroidizing
D. Annealing
45. Heating and slow cooling of metal:
A. Normalizing
B. Annealing
C. Surface hardening
D. Cold rolling
1
2
to 1.
A. 90
B. 105
C. 120
D. 135
37. The circle form which an involute tooth of a
gear is generated or developed:
A. Root circle
B. Base circle
C. Dedendum
D. Mohrs circle
38. The product of the mass and the linear
velocity of a body:
A. Angular impulse
B. Angular momentum
C. Linear impulse
D. Linear momentum
A. Feeler gage
B. Laser
C. Micrometer
D. Diametometer
51. A hand tool used to measure tension in
bolts:
A. Tensometer
B. Torque meter
C. Indexer
D. Torsiometer
52. Distance from center of one tooth of a gear
to the center of the next consecutive tooth
measured on the pitch:
A. Diamettral pitch
B. Pitch circle
C. Circular pitch
D. Module
53. The process of heating a piece of steel to a
temperature within or above the critical
range and cooling rapidly:
A. Annealing
B. Normalizing
C. Hardening
D. Quenching
54. A machine tool in which metal is removed
by means of a revolving cutter with many
stress-strain
A. Modulus of elasticity
B. Plastic range
C. Elastic range
D. None of these
60. The area of the shear diagram of a beam
between any two points on the beam is
equal to the:
A. Change in shear between two points
B. Average moment between the two points
C. Change on the moment between the two
points
D. Change in the deflection between the
two points
61. The three moment equation may be used to
analyze:
A. Continuous beam
B. Beam loaded at the third points
C. Three moment composite beam
D. Axially-loaded beam
62. Poissons ratio is the ratio of the:
A. Unit lateral deformation to the unit
longhitudinal deformation
B. Unit stress to the unit strain
C. Elastic limit to proportional limit
D. Elastic limit to ultimate strength
63. A structure has five unknown reactions
acting on the structure. Three equations of
static equilibrium have been written. To
complete the analysis, which of the
following equations would be needed?
A. Two dynamic equations
B. Three member deformation equation
C. Three more static equilibrium equations
D. Two member deformation equations
64. For most metals Poissons ratio lies in the
range:
A. 0.25 0.35
B. 0.30 0.40
C. 0.35 0.45
D. 0.40 0.50
B. Gray iron
C. White iron
D. Head iron
A. Elasticity
B. Endurance stress
C. Yield stress
D. Ultimate stress
72. A material that can wear away a substance
softer that itself:
A. Tungsten
B. Abrasive
C. Corrosive
D. Carbon
73. In a long column (slenderness ratio , 160),
which of the following has the greatest
influence on its tendency to buckle under a
compressive load?
A. Modulus of elasticity
B. Radius of gyration
C. Moment of inertia
D. None of the above
74. Materials, usually ceramics, employed
where
resistance
to
a
very
high
temperature is required, as for furnace
linings and metal melting pots.
A. Bricks
B. Refractories
C. Insulators
D. Conductors
A. Yield stress
B. Elastic limit
C. Fracture
D. Ultimate strength
A. Calcination
B. Fusion
C. Boiling
D. Forging
A. Planning
B. Shaping
C. Turning
D. Reaming
93. The clearance between tooth profiles of
gear tooth
A. Rack
B. Dedendum
C. Addendum
D. Backlash
A. Brass
B. Bronze
C. Monel
D. Inconel
A. Expansion mandrel
B. Gang mandrel
C. Contraction mandrel
D. Taper mandrel
96. A non-ferrous all consists of nickel and
copper:
A. Reaming
B. Piercing
C. Tuning
D. Boring
86. The
method
compression.
A. Casting
B. Forging
C. Tempering
D. Peening
A. Zinc
B. Tantalum
C. Titanium
D. Chromium
of
A. Monel
B. Bronze
C. Tubing bronze
D. Brass
97. One of the following is not a tap used for
cutting threads in holes.
cold
working
by
A. Tapping tap
B. Plug tap
C. Taper tap
D. Bottoming tap
98. A material is to be drawn into a wire. It
must therefore posses the property of:
A. Toughness
B. Ductility
C. Malleability
D. Hardness
9.
99. When cast steel is used for the body of
machine it is used because:
A. It has non-magnetic properties
B. It has good-self lubricating properties
C. It is cheap
D. It is strong in tension
A. Interference
B. Tolerance
C. Fit
D. None of the above
11. The distance a helical gear or worm will
tread along its axis in one revolution if it
were free to move axially is called:
A. Length of action
B. Line of action
C. Fit
D. Lead
12. Reinstall of second hand boilers shall have a
minimum factor of safety of:
MODULE 10
1.
2.
3.
4.
5.
6.
7.
8.
A. 6
B. 5
C. 4
D. 3
A.
B.
bh2
6
bh3
3
2
C.
D.
bh
12
bh3
12
from
which
variations
are
A. basic dimension
B. nominal size
C. clearance
D. tolerance
27. 1kw is equivalent to:
A. 57 Btu/min
B. 764 hp
C. 41 kcal/sec
D. 44,200 ft-lb/sec
28. The most important factor in determining
high temperature behavior of alloy is:
A. dispersion
B. ionization
C. crystallization
D. composition
29. What is the standard temperature in the
U.S.?
A. Fahrenheit
B. Rankine
C. Celsius
D. Kelvin
that
corresponds
to
heat
A. SAE 1060
B. SAE 117
C. SAE 1030
D. SAE 1020
A. aluminum
B. tin
C. zinc
D. manganese
A. chromium
B. vanadium
C. tungsten
D. nickel
A. manganese
B. sulphur
C. phosphorus
D. silicon
47. A type of welding whereby a wire or powder
form the nozzle of a spray gun is fused by a
gas flame, arc or plasma jet and the molten
particles are projected in form of a spray by
means of compressed air or gas.
A. electro-slug building
B. electro-beam welding
C. plasma-arc welding
D. metal spray welding
for
measuring
A. micrometer
B. tachometer
C. caliper
D. pyrometer
38. Range of helix angle on helical gear:
A. less than 18
B. 15 25
C. 20 35
D. 35 40
39. If p = bearing pressure on projected bearing
areas, z = absolute viscosity of lubricant,
and N = speed of journal, then the bearing
characteristic number is:
A. zN/p
B. z/pN
C. zp/N
D. p/zN
40. Is the permissible variable of the size of
dimension:
A. tolerance
B. allowance
C. clearance
D. interference
A. normalizing
B. tempering
C. quenching
D. annealing
to
A. torsional strength
B. modulus of elasticity
C. twisting moment
D. elasticity
53. In greater quality this element is harmful to
the ferrous metal:
A. sulfur
B. silicon
C. zinc
D. aluminum
54. To prevent leakage in dynamic seal:
A. gaskets
B. seals
C. felts
D. packings
55. It has molybdenum alloy steel, except:
A. SAE 43xx
B. SAE 4xxx
C. SAE 6xxx
D. SAE 47xx
56. A type of gear cut inside a cylinder or ring:
A. rack gear
B. ring gear
C. miter gear
D. internal gear
57. Flexible material used to seal pressurized
fluids, normally under dynamic condition:
B. chromium-moly steel
C. chrome-nickel-molly alloy
D. manganese-moly steel
A. nylon
B. seal
C. Teflon
D. packing
58. Cast alloy steel for very high temperature
application:
A. manganese-nickel steel castings
B. high chrome steel castings
C. chrome-nickel steel castings
D. high manganese castings
59. What heat treatment process can cast steel
materials of high chrome, high manganese,
etc. type steel be subjected for the purpose
of machining process?
A. annealing
B. tempering
C. normalizing
D. quenching
60. Galvanized steel plate is a plate coated
with:
A. aluminum
B. tin
C. zinc
D. manganese
61. Major component of bronze casting:
A. copper
B. manganese
C. zinc
D. lead
62. Fillet radius in machine parts are usually
introduced to:
A. improve the look of the parts
B. reduce concentration of stress and
extend life of the parts
C. to avid obstruction
D. necessary to lessen casting weights
63. Heating of the material to a temperature
above the critical temperature and then
cooling slowly usually in the furnace to
and
improve
the
A. annealing
B. tempering
C. normalizing
D. quenching
64. A hydrostatic bearing is one which:
A. the lube oil is supplied under pressure
B. lube oil is not pressurized
C. there is no oil
D. bearing is lightly loaded
65. One of the following materials is unsuitable
as a bearing:
A. Teflon
B. low carbon steel
C. cast iron
D. nylon
66. Safety features that must be placed and
maintained at machine blacksmith, welding
and foundry shop:
A. safety goggle
B. walkway guide
C. safety notices in markings
D. all of these
67. The angle, at the base of the cylinder of an
involute gear, that the tooth makes with the
gear axis:
A. base helix angle
B. pressure angle
C. arc of recess
D. arc of approach
68. A kind of thread that is generally used:
A. UNEC
B. UNC
C. UNF
D. UNEF
69. Which is not generally used as standard?
A. ASTM
B. SAE
C. IPS
D. AISI
70. In a uniformly loaded simple beam, the
maximum vertical shearing force occurs:
A. at the center
B. at the section of maximum moment
C. at the beam bottom fiber
D. at either end support
71. The capacity of metal to withstand load
without bending is:
A. strength
B. stress
C. elasticity
D. strain
72. Outstanding safety contributes to:
A. high productivity and quality work
B. outstanding performance that expects
reward from the management
C. confidence in foremans ability to
perform well.
D. pride and enthusiasm to one-self
73. A type of coupling that allows slight amount
of torsional/angular flexibility due to
introduction with some elastic material
cylindrically wrapped around the bolts in
the flange.
A. simple elastic bonded coupling
B. elastic-material bushed coupling
C. elastic-material bonded coupling
D. all of these
74. Copper and most of its alloys can be
hardened by:
A. patenting
B. cold working
C. case hardening
D. soaking
75. What happens to a drill if the operating
speed is so fast?
A. drill will crack
B. drill will become overheated and will
bend
C. drill will become overheated and will be
drawn from steel
D. drill will become very dull and wear dust.
76. To reach subjects in mechanical engineering
course, he must be duly licensed ______ or
Masters degree or Doctorate degree holder
in Mechanical Engineering.
A. ME
B. CPM
C. PME
D. CPM, ME and PME
77. To operate, tend or maintain or to be in
charge of the operation, tending, or
maintenance of any mechanical works,
projects or plant of over 2,100kw, he must
be duly licensed ______.
A. ME
B. CPM
C. PME
D. CPM, ME and PME
78. Maximum plant capacity in which a licensed
ME Is allowed to operate, tend, or maintain:
A. 300 kw
B. 1000 kw
C. 2000 kw
D. 3000 kw
79. For a mechanical plant with capacity of 300
kw or over but not more than 2000 kw, the
personnel required to must be at least one
_____.
A. ME
B. PME
C. CPM, ME and PME
D. PME and ME
80. The only accredited national organization
for mechanical engineers.
A. PME
B. NME
C. PSME
D. POME
81. Which furnacedo not belong to the group?
A. Bessemer
B. Open-hearth
C. Induction
D. Pudding
82. Which center is used for supporting open
eng pipes, shells, etc. While turning or
thread cutting in a lathe:
A. ball center
B. half center
C. pipe center
D. female center
83. Steel completely deoxidized with silicon.
A. rimmed steel
B. killed steel
C. capped steel
D. silicate steel
ball
bearings
A. Turning
B. Rolling
C. Casting
D. Cold heading
89. Under which type of loading does fatigue
occur?
A. static load
B. plane load
C. high load
D. repeated load
90. What does the Charpy impact test
measure?
I. The energy required to break a test
sample.
II. The strength of the test sample
III. The ductile to brittle transition point
of metals
A. I only
B. II only
C. III only
D. I and III
91. Which of the following best describes the
0.2% offset of the yield stress?
A. It is the elastic limit after which a
measurable plastic strain has occurred.
B. It is the stress at which the material
plastically strains 0.2%.
C. It is the stress at which the material
elasticity strains 0.2%.
D. It is 0.2% below the fracture point of the
material.
92. The ability of a material to absorb energy
when deformed elastically and to return it
when unloaded is known as:
A. creep
B. hardness
C. toughness
D. resilience
93. In order to realize the advantages of fluid
friction, it is essential to have:
A. parallel oil film in bearing
B. converging oil film
C. no oil film
D. diverging oil film
are
C. isotropy
D. scarcity
3.
A. 4 to 7
B. 7 to 9
C. 9 to 16
D. 5 to 8
powerful
and its
ability of
chemical
4.
A. silicon
B. aluminum
C. carbon
D. sulphur
97. In resistance
released;
welding,
the
pressure
is
5.
6.
A. Plastic
B. Elastic
C. Brittle
D. Annealed
8.
A. compression
B. shear
C. tension
D. double shear
9.
2.
A. welding electrode
B. mechanical shears
C. abrasive wheel
D. acetylene touch
27. Cast iron flywheels are commonly designed
with a factor of safety of
A. 10 to 13
B. 5 to 8
C. 4 to 8
D. 3 to 8
28. The maximum safe rim speed for solid cast
iron pulley is
A. 4200fpm
B. 5000 fpm
C. 6500 fpm
D. 3800 fpm
29. It is a rigid piece of non-elastic substance
which serves to transmit force from one
piece to another or to cause or control
motion:
A. chain
B. belt drive
C. link
D. shaft
30. Machine tools used in the production of flat
surfaces on pieces to lay for a shaper
A. turret lathe
B. shaper
C. boring mill
D. milling machine
31. Ability of the material to withstand high-unit
stress together with great unit strain:
A. resilience
B. toughness
C. malleability
D. ductility
32. High speed tool sheets (HSS) are used for
the working of metals at high cutting speed.
AISI specification include
A. molybdenum types
B. high-carbon type
C. chromium type
D. carbon-tungsten type
33. Effective face width of a helical gear divided
by gear axial pitch.
A. face overlap
B. teeth overlap
C. land overlap
D. pitch overlap
34. Directly hardenable steels are considered in
five groups and the basis is approximate
carbon content. Heat treated parts
requiring moderate strength and great
toughness.
A. 0.40 0.42%
B. 0.30 0.37%
C. 0.45 0.50%
D. 1.02%
35. The best material for crane hoisting chain
A. wrought iron
B. cast iron
C. malleable iron
D. commercial steel
36. An ISO metric thread is designated M8
x1.25 -6g. The thread has a pitch of
A. 0.8 mm
B. 1.25 mm
C. 0.6 mm
D. 8 x 1.25 mm
37. The permissible variation in size of a
dimension
A. tolerance
B. clearance
C. interface
D. allowable
38. Center to center distance between
sprockets as a general rule shall not be less
than 1 times the diameter of the large
sprocket and not less than ______ times the
pitch nor more than _____ times the pitch.
A. 20, 40
B. 30, 50
C. 50, 80
D. 10, 30
39. For punching and shearing machinery a
speed variation of ____ may be allowed in
all flywheel design
A. 1 to 2%
B. 5 to 10%
C. 20%
D. 50%
40. For maximum rope life of 6 x 7 the
minimum sheave diameter, D in terms of
the rope diameter is
A. D = 72d
B. D = 45d
C. D = 30d
D. D = 27d
41. When baked, which alloy does not change
much
A. nickel alloys
B. phosphor bronze
C. brass
D. copper
42. Cast iron flywheels are commonly designed
with a factor of safety of:
A. 12 to 16
B. 9 to 10
C. 9 to 12
D. 10 to 13
43. It is recommended not to have direct drive
and rive sprockets fit eh ratio of their teeth
exceeds _____, use two or more step
combination.
A. 10 times
B. 8 times
C. 5 times
D. 6 times
44. Some experiment made at Cornell
University showed that experienced
mechanic could break a _____ bolt due to
tightening
A. 3/8
B. 5/8
C.
D. 7/16
45. Which of the following furnaces do not
belong to the group?
A. blast furnace
B. salt bath electrode
C. reactor furnace
D. over or reactor furnace
46. The factor of safety for operating rope is
A. 5 to 12
B. 3 to 4
C. greater than 12
D. 2 to 6
47. A nickel alloy which is age-hardenable with
good spring and low-sparking properties
and slightly magnetic after heat treatment:
A. monel
B. hastealloy
C. duranickel
D. inconel
C. pitch plane
D. normal plane
77. What will be the effect in bushing gears
without backlash
A. jamming
B. overheating
C. overload
D. all of these
MODULE 12
1.
3.
4.
5.
6.
7.
8.
9.
A. top land
B. bottom land
C. pitch
D. fillet
13. Also called eccentrically loaded bearing:
A. full bearing
B. offset bearing
C. partial bearing
D. fitted bearing
14. The distance the helical gear of worm would
thread along its axis in one revolution if it
were free to move axially:
A. lead
B. thread
C. pitch
D. land
15. Which does not belong to the group?
A. SAE
B. AISI
C. SEA II
D. ASTM
16. What is the SAE specification number of
Molybdenum-chromium-nickel?
A. 48XX
B. 47XX
C. 46XX
D. 45XX
17. The over arm of a milling machine is used
to support:
A. spindle
B. arbor
C. column
D. table
18. The rated life of a bearing changes:
A. directly as load
B. inversely as fourth power of load
C. inversely as cube of load
D. inversely as square of load
19. In general, the design stress and factor of
safety are related as follows:
A. design stress = ultimate stress times
factor of safety
B. design stress = ultimate stress divided
by factor of safety
C. factor of safety = design stress divided
by ultimate stress
D. ultimate stress = factor of safety divided
by design stress
20. Curve formed by the pitch of a point of the
extension of a circle as it rolls along a curve
or line
A. trochoid
B. involute
C. spiral
D. cycloid
21. Product of mass and linear velocity is
known as:
A. impulse
B. linear momentum
C. angular momentum
D. impact
22. Which of the following is not an iron ore?
A. hematite
B. siderite
C. limonite
D. sulfurite
23. The blow of pressure of a safety valve is:
A. slightly more than atmospheric pressure
B. half of boiler working pressure
D. arc of recess
35. A combination of resistant bodies so
arranged that by their means the
mechanical forces of mixture can be
compelled to produce the same effect or
work accompanied with certain
determination motion:
A. turbine
B. resistors
C. machine
D. mechanism
36. A vertically loaded, fixed at one end and
simply supported at the other is
indeterminate to what degree?
A. first
B. second
C. third
D. fourth
37. Roller chain subjected to standard
measuring load are allowed an over-length
of
A. 1/54 inch/foot
B. 1/84 inch/foot
C. 3/8 inch/foot
D. 1/60 inch/foot
38. What does the Charpy impact test
measure?
I. the energy required t break a test
sample
II. the strength of a test sample
III. the ductile to brittle transition
point of metals
A. I only
B. II only
C. I and II
D. I and III
39. Poissons ratio is principally used in
A. the determination of capability of a
material for being shaped
B. the determination of capacity of a
material for plastic deformation without
fracture
C. stress-strain relationships where stress
are applied in more than one direction
D. the determination of the modulus of
toughness
40. The maximum stress induced in a material
when subjected to alternating or repeated
loading without causing failure:
A. elasticity
B. endurance stress
C. yield stress
D. ultimate stress
A. a continuous beam
B. a beam loaded at three points
C. a step tapered column
D. a three element composite beam
55. Which micrometer has no anvil?
A. outside micrometer
B. depth micrometer
C. screw thread micrometer
D. digit micrometer
56. A stud is which
A. have threads on one end
B. require a nut
C. inserted in a plane hole
D. none of the above
57. A kind of chuck which has reversible jaws
which could be adjusted properly
A. universal chuck
B. chuck Connors
C. chuckle chuck
D. independent chuck
58. Principal stresses occur on those planes
A. where the shearing stress is zero
B. which are 45 apart
C. where the shearing stress is a maximum
D. which are subjected only to compression
59. According to the PSME Code, for safety
purposes, stairs, platforms, and landing
shall sustain not less than 500 kg and with
a factor of safety of:
A. 3
B. 10
C. 4
D. 5
60. Tool which when pressed into a finished
hole in a piece of work provide centers on
which the piece may be turned or otherwise
machined.
A. spindle
B. clock
C. mandrel
D. jaws
61. RC 50 chain is a chain of normal proportion
its pitch is
A. 5/8 deg
B. 7/8 deg
C. 5/16 deg
D. cannot be determined
62. Foundation depth may be taken as ___
times the engine stroke when engine have
a few cylinders and situated on less firm soil
A. 3.2
B. 4.2
C. 2.4
D. 2.3
63. The differential of the shear equation is
which one of the following?
A. load on the beam
B. tensile strength of beam
C. bending moment of the beam
D. slope of the elastic curve
64. In which screw thread the side width of flat
= width of space = 0.5p:
A. knuckle
B. buttress
C. square
D. acme
65. The outbreak of fire can be avoided by
preventing:
A. fuel
B. heat
C. oxygen
D. any of the above
C. in a and b both
D. neither a nor b
78. In case of a limit plug gauge which size will
not enter into the hole:
A. GO size
B. a and b both
C. NOT GO size
D. none of the above
C. 90 and 45 deg
D. 180 deg only
A. lead
B. GI sheet
C. aluminum
D. cast iron
91. Which micrometer is available with
extension rods:
A. outside micrometer
B. inside micrometer
C. screw thread micrometer
D. combi micrometer
92. Which gauge is used to check the internal
threads:
A. plug gauge
B. ring gauge
C. thread plug gauge
D. thread ring gauge
93. Concentricity of an outside diameter can be
checked by:
A. vernier caliper
B. outside micrometer
C. dial test indicator
D. tube micrometer
94. Which of the following do not belong to the
group?
A. TIG
B. MIG
C. hardening
D. soldering
95. The slenderness ratio of a column is
generally defined as the ratio of its
A. length to its minimum width
B. unsupported length to its maximum
radius of gyration
C. length to its moment of inertia
D. unsupported length of its least radius of
gyration
96. The moment at a section of beam is
delivered from the
A. sum of the moments of all external forces
on side of the section
B. difference between the moments on one
side of the section and the opposite side
C. sum of the moments of all external
forces on both sides of the section
D. sum of the moments of all external
forces between supports
97. The effect of setting a lathe tool a small
amount below the center of the work is to
A. increase the rake angle
B. decrease the rake angle
C. cut with negative rake
D. leave the rake angle unaltered
98. A combination of resistant bodies so
arranged that the motion of one compels
the motion of the others.
A. gears
B. cams
C. mechanism
D. machine
99. Which of the following is not a method of
non-destructive testing of steel castings
and forgings?
A. radiography
B. magnetic particle
C. ultrasonic
D. chemical analysis
B. 48 65
C. 40 50
D. 30 60
MODULE 13
1.
2.
3.
4.
5.
6.
7.
8.
9.
A. chromium
B. manganese
C. selenium
D. molybdenum
12. Which of the following is not a kind of
mandrel?
A. expanded
B. extended
C. contraction
D. taper
13. The ratio of the arc of action to circular
pitch or length of action to base pitch
A. approach ratio
B. contact ratio
C. arc of ratio
D. arc of approach
14. A cutting tool angle between the side
cutting edge and the plane perpendicular to
direction of feed travel is ___ angle.
A. side relief
B. side cutting edge
C. lead
D. side rake
15. The surface between the pitch circle and
the bottom land
A. line of action
B. flank of tooth
C. bottom land
D. face of top land
16. A section in a machine shop operation.
A. core making
B. machining
C. fitting
D. pattern
17. Test showed that steel pulleys has less
slippage than that of cast iron pulleys in
range of:
A. 1.8 2.6
B. 1.8 2.8
C. 2.35 2.7
D. 2.0 2.8
18. The bottom surface joining two sides of
thread in screw.
A. pitch
B. crest
C. bottom land
D. root
19. Shear modulus is also:
A. shear elasticity
B. Poissons ratio
C. modulus of elasticity
D. modulus of rigidity
20. To prevent leakage in dynamic seal:
A. gaskets
B. seals
C. packings
D. felts
21. Top surface joining two sides of thread in
screw.
A. pitch
B. top flank
C. top land
D. crest
22. The frictional forces depends on coefficient
of friction and:
A. torque
B. weight of object
C. normal force
D. moment
23. The number of cycles required to cause
failure for given stress level.
A. endurance
B. fatigue
C. fatigue life
D. rupture
24. The tool blade made of tool blank consists
of face, nose, shank, and ___.
A. cutting edge
B. none of these
C. round nose
D. base
25. The cutting tool used in the shaper are
similar to turning tools of ___ machine
A. planer
B. broaching
C. boring
D. lathe
26. The blades of hacksaw have number of
teeth range of:
A. 15 38 tooth/in
B. 14 32 tooth/in
C. 12 30 tooth/in
D. 12 32 tooth/in
27. The safeguard in minimum of ___ mm in
height for the use as toe guard/toe board.
A. 165
B. 135
C. 150
D. 120
28. Not part of the headstock.
A. back gear
B. anvil
C. spindle
D. motor
29. A lathe carriage part that bridge across the
bed to carry the cross slide and tool rest.
A. automatic feed
B. compound rest
C. apron
D. saddle
30. Screw thread projecting from a cylindrical
surface.
A. thread series
B. straight thread
C. thread shear area
D. taper thread
31. Vertex distance is a term used in ____
gearing.
A. spiral
B. bevel
C. worm
D. zerol
32. Two or more forces acting together could be
replaced by a single force with the same
effect in a mass
A. couple forces
B. resultant
C. resolution forces
D. concurrent forces
A. left side
B. two sides
C. no
D. one side
56. An RC 40, roller chain has a pitch of:
A. in
B. in
C. 1/8 in
D. 7/8 in
57. Which of the following combustion that has
a property of resilience?
A. grease
B. graphite electrode
C. rubber
D. graphite powder
58. Nano is an exact opposite of:
A. 106
B. micro
C. giga
D. pico
D. 12 32 teeth/in
9.
A. shaving
B. burnishing
C. all of these
D. lapping
1.
2.
3.
4.
5.
6.
7.
8.
A. Welding
B. Blacksmith
C. Brazing
D. Forging
(ME Bd. Oct 2005)
13. In straddle milling the number of cutters
used to cut:
A. One
B. Two
C. Three or more
D. Any of these
(ME Bd. Oct 2005)
14. Concentricity of an outside diameter of the
shaft can be checked by using:
A. Bench center and Dial test indicator
B. Bench bottom and Caliper
C. Bench vise and planer
D. Center post meter
(ME Bd. Apr 2005)
15. Almost always the soldering materials are a
combination of the following alloys:
A. All of these
B. Lead and tin
C. Tin and antimony
D. Lead and antimony
(ME Bd. Apr 2005)
16. Blanking is a process associated with
A. Shearing
B. Tension
C. Compression
D. Compression and tension
(ME Bd. Apr 2005)
17. Machine tool used for laying straight lines
on metal surfaces made of sharp tool steel
is called:
A. Plain scriber
B. Divider
C. A trammel
D. Caliper
(ME Bd. Apr 2005)
18. The most popular of all soldering materials
in use has a composition of:
A. 45/55% tin and lead
B. 50/50% tin and lead
C. All of these
D. 60/40% tin and lead
(ME Bd. Apr 2005)
19. Fillet radius in machine parts is usually
introduced to:
A. Improve the look of the parts
B. Reduce concentration of stress and
extend life of the parts
C. To avoid obstruction
D. Necessary to lessen casting weights
(ME Bd. Apr 2004)
20. Lathe spindle has got:
A. No threads
B. External threads
C. Taper threads
D. Internal threads
(ME Bd. Apr 2004)
21. A machine designer decided to use a
pneumatic cylinder to lift a metal part to
feed a conveyor. Which valve is used to
command the cylinder?
A. Non-return valve
B. Pilot-check valve
C. Two-way solenoid valve
D. Air piloted directional valve
(ME Bd. Apr 2004)
22. Centrifugal method of casting is used to:
A. Ensure purity and density at extremities
of a casting
B. Use heavy cast iron mould to act as chill
C. Obtain high density and pure castings
D. Cast symmetrical objects
(ME Bd. Apr 2004)
23. In permanent mould casting method
A. Molten metal is feed into the cavity in
metallic mould by gravity
B. Gravity is filled with precalculated
quantity of a metal and a core or plunger is
inserted to force the metal into cavity
C. Metal is poured into die cavity and at a
predetermined time the mould inverted to
permit a part of metal still in molten state
to flow out of cavity
D. Metal is forced into mould under high
prressure
(ME Bd. Apr 2004)
24. _____ for ferrous materials, the helix angle
of drill is:
A. 45 degrees
B. 90 degrees
C. 30 degrees
D. 60 degrees
(ME Bd. Apr 2004)
25. A double fillet welded joint with parallel
fillet weld of length L and leg B is subjected
to a tensile force P. Assuming uniform stress
distribution, the shear stress in the weld is
given by
A. P/2.B.L
B. 2 .P/B.L
C. P/2 .B.L
D. 2/B.L
(ME Bd. Apr 2004)
26. _____ a standard ground drill has a point
angle of
A. 130 degrees
B. 100 degrees
C. 118 degrees
D. 90 degrees
(ME Bd. Apr 2004)
27. A 5 degrees taper over 5 mm length is to be
made on a 100 mm diameter job. Which
method should be used?
A. Tail stock offset method
B. Taper turning attachment
C. From tool method
D. Compound rest method
(ME Bd. Apr 2004)
28. A machining process is pneumatically
operated. Its drive is
A. Hydraulic cylinder
B. Hydraulic pump
C. Solenoid valve
D. Pneumatic cylinder
(ME Bd. Apr 2004)
29. Pick up the incorrect statement about
advantages of disposable patterns
A. Finish is uniform and reasonably smooth
B. No complex wooden pattern will loose
piece is required
C. No cores are required
D. Patterns can be handled easily and
process is adaptable to mechanical
moulding equipment
(ME Bd. Apr 2004)
30. The main purpose of boring operation, as
compared to drilling is to
A. Enlarge the existing hole
B. Finish the drilled hole
A. Die casting
B. Pressed casting
C. Gravity casting
D. Continuous casting
64. During MIG welding the metal is
transformed in the form of:
A. Continuous flow of molten metal
B. A fine spray of metal
C. Solution
D. Electron beam
65. A collimated light beam is for producing
heat in:
A. MIG welding
B. TIG welding
C. Plasma welding
D. Laser welding
66. Wipping is the process of:
A. Cleaning the welded surface after the
welding operation is over
B. Applying flux during welding process
C. Connecting load pipes by soldering alloy
D. Low temperature
67. In which of the following process hydraulic
fluid acts as transfer media?
A. Electron beam machining
B. Electro-discharge machining
C. Iron beam machining
D. Water jet machining
68. Sweep pattern is used for moulding parts
having:
A. Rectangular shape
B. Uniform symmetrical shape
C. Complicated shape having intricate
details
D. None of the above
69. Drossing
A. A method of cleaning the castings
B. An inspection method for castings
C. A method of deoxidation of molten metal
D. The formation of oxides on the molten
metal surface
70. The usual value of helix angle of a drill is:
A. 110
B. 120
C. 30
D. 60
71. A twist drill is specified by:
A. Its diameter and lip angle
B. Its shank and diameter
C. Shank, material and flute size
D. Shank, material and diameter
A. It is an automatic machine
B. It is a mass production machine
C. Semi-skilled operators can be employed
D. Operation is completed in one stroke
73. Choose the one that will have the highest
cutting speed.
A. Cast iron
B. Tool steel
C. Brass
D. Aluminum
74. Laser welding is widely used in:
A. Process industry
B. Structural work
C. Heavy duty
D. Electronic industry
75. Unlike materials or materials of different
thickness can butt welded by:
D. Stainless steel
A. Fan
B. Hand blower
C. Air cylinder
D. Centrifugal blower
92. Tumbling is done so as to:
A. Clean the surface of small parts
B. Stress relieve the components
C. Get surface finish
D. To plate the surface
93. The purpose of inoculation is:
A. To clean casting
B. To decrease the melting temperature
C. To change the chemical composition of a
cast metal
D. To modify the structure and properties of
a cast metal
94. Least shrinkage allowance is provided in the
case of which of the following?
A. Brass
B. Cast iron
C. White cast iron
D. Aluminum
95. The draft allowance on metallic pattern as
compared to wooden ones is:
A. More
B. Same
C. Less
D. More or less depending on size
96. Select the one that is not an angle
measuring device.
A. Bevel protector
B. Sine bar
C. Combination square
D. Angle iron
97. Dilatometer is used to find out which
property of moulding sand.
A. Permeability
B. Hot strength
C. Fineness
D. Moisture content
B. Pyramidal form
C. Cylindrical form
D. Needle form
9.
C. Drill
D. Grinder
21. Welding operation in which a non-ferrous
filler metal melts at a temperature below
that of the metal joined but heated above
450C
A. Filled weld
B. Soldering
C. Brazing
D. TIG welding
22. The process of checking or producing
checkers on the surface of a piece by rolling
checkered depressions into the surface:
A. Indexing
B. Knurling
C. Quenching
D. Soldering
MODULE 15
1.
A. Thermoplastics
B. Phenolics
C. All of the above
D. Thermosetting plastics
13. The effect of alloying zinc to copper is:
A. To increase hardness
B. To impact free-machining properties
C. To improve hardness and strength
D. To increase strength and ductility
14. Grey cast iron is best welded by:
2.
A. MIG
B. Submerged arc
C. TIG
D. Oxy-acetylene
15. The impedence of piezo-electric crystal is:
3.
Undercutting is:
A. An operation of cutting extra deep
groove
B. An operation of cutting a groove next to
a shoulder on a piece of work
C. Cutting from the base of a work piece
D. An operation of cutting extra wide
threads
4.
5.
6.
7.
8.
A. Negligible
B. Low
C. High
D. Very high
16. Honing is used:
A. To remove only small amount of metal
B. To correct axial run-out of a bore
C. To correct out-of-roundness of a bore
D. On surfaces brought to high degree to
surface finish
17. Which of the following is not a method by
which a single lap joint usually falls?
A. The rivets shear
B. The plate fails in bearing
C. The plate fails in tension
D. The rivet fail in tension
18. A device for accurately measuring
diameter:
A. Feeler gage
B. Laser
C. Micrometer
D. Diametometer
19. A hand tool used to measure tension bolts:
A. Tensometer
B. Torque wrench
C. Indexer
D. Torsiometer
20. A machine tool in which metal is removed
by means of a revolving cutter with many
teeth, each tooth having a cutting edge
which removes its share of the stock.
A. Milling machine
B. Lathe
B. Caliper
C. Tachometer
D. Pyrometer
44. Not adaptable to welding due to strength
and poor ductility:
A. Copper parts
B. Cast iron parts
C. Aluminum parts
D. All of these
45. In a planer the feed is provided:
A. At forward stroke
B. At return stroke
C. In between forward stroke
D. In between return stroke
46. Taps are resharpened by grinding:
A. Flutes
B. Diameter
C. Threads
D. Relief
47. The over arm of a milling machine is used
to support:
A. Spindle
B. Column
C. Arbor
D. Table
C. Thermit welding
D. Plasma arc welding
55. Concentricity of an outside diameter can
checked by:
A. Vernier caliper
B. Outside micrometer
C. Dial test indicator
D. Tube micrometer
56. Generally spiral fluted reamer has spirals of:
A. Left hand
B. Straight
C. Right hand
D. None of the above
57. The new hacksaw blade should not be used
in old cut because:
A. The blade is very costly
B. The blade have very sharp teeth
C. The space is not sufficient to play the
new blade in the old cut
D. None of the above
58. Which part of the file is not hardened?
A. Tang
B. Crest
C. Body
D. Point
A. Plug gauge
B. Ring gauge
C. Thread plug gauge
D. Thread ring gauge
67. Which of the following do not belong to the
group?
A. TIG
B. Hardening
C. MIG
D. Soldering
68. For workrooms (maintenance shop and
machine room) shall at least have a height
from floor to ceiling of:
A. 1000 mm
B. 3000 mm
C. 2000 mm
D. 1500 mm
69. In case of a limit plug gauge which size will
not enter into the hole:
A. GO size
B. A and B both
C. NOT GO size
D. None of the above
70. The process of producing a variety of
surfaces by using a circular type cutter with
multiple teeth.
A. Grinding
B. Milling
C. Turning
D. Welding
71. The square head of a combination set is
used for making or checking the angles:
A. 90 deg only
B. 90 and 45 deg
C. 45 deg only
D. 180 deg only
72. The tool blade made of tool blank consists
of face, nose, shank, and _____.
A. Cutting edge
B. Round nose
C. None of these
D. Base
73. The cutting tool used in the shaper are
similar to turning tools of _______ machine.
A. Planer
B. Boring
C. Broachiing
D. Lathe
74. The blades for hacksaw have number of
teeth range of:
A. 15 38 tooth/in
B. 12 30 tooth/in
C. 14 32 tooth/in
D. 12 32 tooth/in
75. The safeguard in minimum of _____ mm in
height for the used as toe guard/toe board.
A. 165
B. 150
C. 135
D. 120
76. A lathe carriage part that bridge across the
bed to carry the cross slide and tool rest.
A. Automatic feed
B. Compound rest
C. Apron
D. Saddle
77. A section in a machine shop operation.
A. Coremaking
B. Fitting
C. Machining
D. Pattern
A. Round nose
B. Center cut
C. Square nose
D. Thread cutting
94. A lathe machine threading mechanism:
A. Reverse gear and lever
B. Spindle gear
C. All of these
D. Change stud gear
95. What is the common shop practice to
prevent solder from running away from its
surface to be joined?
A. All of these
B. Surround the work with clay
C. Introduce around the work rolled with
cloth
D. Put asbestos sheering around the work
96. What happens to a drill if operating speed is
too fast?
A. Drill will crack
B. Drill will become overheated and will
bend
C. Drill will become overheated and will be
drawn from the steel
D. Drill will become very dull and wear dust
97. The machinery operation whereby done
with the work accurately fastened has a
reciprocating (forward and backward)
motion and the tool head is stationary.
A. Shaping
B. Planing
C. Turning
D. Reaming
98. What is the difference between the a
shaper and a planer?
A. Electro-slug welding
B. Electro-beam welding
C. Plasma-arc welding
D. Metal spray welding
B. Walkaway guide
C. Safety notices in markings
D. All of these