Beruflich Dokumente
Kultur Dokumente
Guide
-2-
Table of Contents
1. Before Installation
1.1 To install ----------------------------------------------------------- 4
1.2 Product package ------------------------------------------------ 4
2. Installation Environment ---------------------------------------------- 6
3. System Configuration
3.1 Network mode ----------------------------------------------------- 7
3.2 Standalone mode ------------------------------------------------- 8
4. Installation
4.1 Fastening the auxiliary plate ---------------------------------- 9
4.2 Attaching other devices except the terminal -------------- 11
4.3 Connecting external cables ----------------------------------- 12
4.4 Fastening the terminal ----------------------------------------- 16
5. Check After Installation ----------------------------------------------- 18
-3-
1. Before Installation
1.1 To install
Please follow the installation guide because the performance
can be decreased if the product is installed incorrectly.
1.2 Product package
Product
Pictures
Qty
Use
Terminal
1ea
Access Controller
Adapter
1ea
Power cord
1ea
Rear case
1ea
-4-
Bolt
4ea
6ea
Housing
1ea
Receptacle
6ea
S/W CD
1ea
-5-
2. Installation Environment
Please keep in mind the following conditions when you install the
product. You might need to obtain the user's consent if necessary.
This product is originally designed to install indoors. If you
have to install it outdoors, however, do not expose the terminal
to direct sunlight, snow or rain.
The connection cables should not be exposed outside, and it
is highly recommended to bury them underground. If that is
impossible, you must obtain the user's consent before
installation.
Power supply should begin after all connections are completed.
Do not disconnect the lines or make any additional
connections while the power is supplied.
If you install the product as an access controller at a proper
height for the users and in a near place that facilitates control
of the entrance, you can use it more efficiently.
The power requirement for the system is AC 100~240V,
50/60Hz.
-6-
3. System Configuration
3.1 Network mode
Terminals are connected by network and it can be remote
control.
Server PC
Client PC
Network(TCP/IP)
Terminal
Lock
-7-
Locking Device
Interphone
-8-
4. Installation
The overall installation procedure is as follows:
Fasten the bracket
Attach other devices except terminal(locking device, interphone,
etc.)
Figure 4.1 Making the hole for wiring in the rear case
-9-
Align the bracket with the hole for wiring as shown Figure
4.2, and fasten it with 6 bolts supported in the packet.
- 10 -
Locking device
Door Open button
Types of installable locking devices and specifications
Type
Specifications
Remarks
Deadbolt
input: DC12V,
1A or lower
Fail Safe/Secure
Electronic
input: DC12V,
Voltage output,
1A or lower
Fail Safe/Secure
Magnetic-Lock
Electric Strike
Auto Door
Voltage output,
input: DC12V,
Voltage output,
1A or lower
Fail Safe/Secure
Contact output
Receptacle
5263PBT
Cable
UL Cable, 24~28AWG
Connection Note
Pay attention to terminal numbers when connecting the cable to
the connector.
Contact output is used when installing on the auto door. So make
sure to set the terminal [JP3] as OPEN. The factory default of
the terminal [JP3] is JUMPER.
Some locking devices may not have door monitoring signals.
How to connect cables by types of locking devices
Deadbolt Strike
Contact_A
Power(Fail Secure)
Common
Contact_B
Power(Fail Safe)
Door Monitor
Door Open
GND
Door Open Button
- 12 -
EM Lock
Deadbolt/Strike/Electronic Magnetic-Lock
PIN
Feature
NO.
Fail
Fail
Secure
Safe Type
GND
Door Monitoring
CONTACT_B
COMMON
CONTACT_A
Type
GND
Door
Door
Monitoring
Open
GND
COM
Open
button
Open
button
Monitor
(12/24V)
VCC(12/24
V)
(COM)
VCC(12/24
V)
PIN
Feature
NO.
1
GND
Door Monitoring
CONTACT_B
Normal
Normal
Door
Door
Open
Close
Monitoring
Open
COM
Open
button
Open
button
Monitor
(12/24V)
Contact
COMMON
Contact
CONTACT_A
Contact
Contact
- 13 -
Housing
Schematic
Cable
RJ45, 8PIN
PIN No
Feature
TXP
TXN
UTP
RXP
RXN
Function
GND
Wiegand 1
Wiegand 0
+5VDC
- 14 -
Function
GND
TRX-
TRX+
Function
+5VDC
GND
Wiegand 0
Wiegand 1
- 15 -
- 16 -
- 17 -
- 18 -