Beruflich Dokumente
Kultur Dokumente
Mobile Backhaul
Solution Design Guide
Key Design Considerations, Topologies and
Configuration for Juniper Networks Mobile Backhaul
Solution for 2G/3G and LTE Networks
Table of Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Solution-Type Design Guidance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Mobile Backhaul Solution with ACX Series Universal Access Routers for Multi-Generation Networks. . . . . . . . . . . . . . . . .3
Solution Description Key Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Design Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Taking MPLS to the Access Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Architecture and Network Design Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Network Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Network and Service Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Solution Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Network Topology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
IGP Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
MPLS Label Transport Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
BGP Setup in the Aggregation and Edge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Service Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Layer 3 VPN Service Model for LTE Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Layer 2 VPN Pseudowire Service for 2G/3G/LTE Traffic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Appendixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Introduction to Mobile Backhaul Technologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
BTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
BSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Mobile Core: PDSN/GGSN/SGSN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
What is a Mobile Backhaul. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
About Juniper Networks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
List of Figures
Figure 1: Architectural Transformation in the Mobile Service Provider Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 2: Juniper Mobile Backhaul Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 3: Juniper mobile backhaul solution deployment example for 2G/3G/LTE services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 4: RSVP tunnels with fast reroute in access and aggregation rings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 5: Layer 3 VPN Service Model for LTE Traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 6: L2 VPN pseudowire service between CSR and PE router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 7: Overview of a generic mobile backhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 8: Subcomponents of mobile backhaul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Introduction
Convergence and network simplification on the network edge and core have been hallmark trends for service providers
in recent years. Access networks could also benefit from consolidation, but this has remained a challenge due to the
disparate technologies developed for mobile, residential, and business access. The varieties of network access have
evolved over time, from circuits to packets, from time-division multiplexing (TDM) to IP/Ethernet, and from wireline
to wireless. So it is only natural that there are multiple access networks for different applications with many touch
points, and this reality leaves operators with an obvious management challenge. As the bandwidth demands from
smartphones and other mobile devices has grown exponentially over the years, the first logical choice has been to
focus on adding capacity in the form of point-to-point bandwidth from access to aggregation, with the only innovation
being to replace TDM with Ethernet. Truck rolls are typically required for minor operational changes with this approach,
and there is inconsistent quality in telephone calls (jitter, dropped calls) and Internet access connections.
As more and more access connections require wireless support and with the proliferation of mobile-to-mobile and
mobile-to-machine applications, the challenges facing mobile operators become of paramount concern. These
challenges range from the rising tide of packet traffic, to the underlying transport technology, to management of the
end-to-end network.
Instead of relying on separate access devices to connect customers, it is desirable to have a converged access network
to deliver both a more predictable experience to users and better economics for service providers and shareholders.
Junipers Universal Access solution is based on the high-performance Juniper Networks ACX Series Universal Access
Routers, anchoring the first fully integrated, end-to-end network architecture that combines operational intelligence with
capital cost savings. With Universal Access, operators can extend the edge network and its capabilities to the customer,
whether thats a cell tower, a multi-tenant unit, or a residential aggregation point. This creates a seamless network
architecture thats critical to delivering the benefits of fourth-generation (4G) radio and packet core evolution with
minimal truck rolls, paving the way for new revenue, new business models, and a more flexible and efficient network.
Scope
Addressing the challenges faced in the access network by mobile service providers (MSPs), this document describes
Junipers mobile backhaul solution with ACX Series Universal Access Routers to specifically address the legacy
and evolution needs of the mobile network. The solution describes design considerations and deployment choices
across the multiple segments of the network, while providing implementation guidelines to support services that can
accommodate todays mobile network needs and support not only legacy services on 2G/3G networks, but also a
migration path to Long Term Evolution (LTE)-based services.
Hosted
Services
Internet
Internet
Off-net
Services
PSTN
HLR
HSS
PCRF
IP
MSC/GW
GGSN
IP
SGSN
ATM/IP
On-net
Services
IP
HSS
PCRF
Hierarchical
to Flat;
Hub-Spoke to
Fully Meshed;
TDM/ATM
to All-IP
MME-Pool
SGW
Control Plane
PGW
User Plane
3GPP Evolved
Packet System
RNC/BSC
IP
TDM/ATM
ULTRAN
NodeB
NodeB
Enhanced NodeB
Universal Edge
ACX Series
2G GSM/
CDMA
1588v2 BC
Mobile Access
(Eth/MPLS/MPLS-TP)
MX Series
GGSN SGSN
MX240
ACX Series
3G UMTS/CDMA 1x EV-DO
MX Series
MX10/MX40/
MX80
Pre-Aggregation
(Eth/MPLS/MPLS-TP)
RNC/BSC
Metro Aggregation
(MPLS/MPLS-TP)
1588v2
Grand Master
SGW
MME
PGW
MX Series
ACX Series
BRAS
and BNG
MX240
ACX Series
Converged Access
(Eth/MPLS/MPLS-TP)
4G LTE and
LTE-Advanced
AAA
MX240
1588v2
Grand Master
ACX Series
Multimedia
Database
Server
ACX Series
Small Cells
Design Considerations
Taking MPLS to the Access Network
Over the last few years, the industry has seen a growing investment in Ethernet as the transport infrastructure, and
in MPLS as the packet-switching technology. Junipers advanced mobile backhaul solution with ACX Series routers is
designed to help MSPs move to an all IP/MPLS packet network and address the growing services needs of increasing
bandwidth and enhanced quality of experience (QoE). Further, recent studies indicate that use of MPLS in the access
network results in better network economics over traditional Layer 2 Ethernet networks.1 Juniper provides an industryleading solution to deliver a services architecture that moves MPLS from core and aggregation into the access layer,
providing the necessary functionality and performance needed to build highly resilient, large-scale, modern day networks.
The key benefits of building an end-to-end MPLS network for wireless services include:
MPLS can support multiple types of transport infrastructure. It can efficiently carry both packet and non-packet
application traffic over hybrid underlying infrastructure that includes TDM, ATM, and Ethernet.
Taking MPLS into the access network, and enabling MPLS end-to-end in a single domain with MPLS as the single packet
transport mechanism, can allow services to be decoupled from the underlying infrastructure. Services can be initiated as
MPLS pseudowire or MPLS Layer 3 VPN at the cell site, and can be flexibly mapped to MPLS services at the aggregation
and edge nodes further upstream in the network. In contrast, traditional networks have relied on backhauling L2
technologies and carrying traffic over Ethernet VLANs, Frame Relay data-link connection identifier (DLCI) or ATM virtual
circuits. This resulted in a tighter coupling of the service provisioning to the underlying topology and limited flexibility in
operations having to deal with several technologies for any given service.
With a homogenous MPLS transport network-wide, operators can benefit from a simplified service provisioning model
and minimize the number of provisioning touch points, resulting in faster deployment of services and simpler operations.
An all-MPLS network with MPLS services originating at the cell site router can significantly streamline operations. For
example, when re-parenting of cell sites is needed, it is much easier and more cost-effective to move MPLS Layer 3
services than to reconfigure hard provisioned Frame Relay DLCI or ATM virtual circuits.
With the notion of end-to-end label-switched paths (LSPs), MPLS delivers strong and resilient traffic engineering
capabilities to redirect traffic in the event of network node or link failures and also to maximize the use of network
resources in stable conditions. Junipers MPLS portfolio supports a comprehensive OAM toolkit to facilitate speedy
detection of failures, as well as the necessary service restoration features to ensure sub-second convergence to deliver
carrier-class functionality.
1
See Pietro Belotti, Comparison of MPLS and Ethernet Networks at the Access-Aggregation Level (http://myweb.clemson.edu/~pbelott/papers/comparison-eth-mpls.pdf).
MPLS, when deployed systematically network-wide, can meet the scaling needs of the largest of modern day networks.
Junipers solution with seamless MPLS is specifically designed to support large-scale networks of the order of 100,000
nodes. Key features such as BGP labeled unicast and LDP downstream on demand (DoD) can be utilized to enable and
extend the right level of service and operational intelligence in the several layers of the network.
MPLS also tends to be an easier platform for deploying and integrating multi-market services. With the topological
independence that MPLS creates at the service layer, services such as Wi-Fi offload, access point name (APN), or support
for multiple MSPs on one cell site can easily be accommodated with the virtualization provided by MPLS L3 VPNs
Network Elements
Cell Site Router
The cell site router is typically deployed at the cell site and connects the base station (BS) to the packet network.
Several cell site routers can be connected in a ring or hub-and-spoke fashion to the upstream pre-aggregation/
aggregation routers. Key requirements of a cell site router include:
Support for TDM and Ethernet interfaces to meet multi-generation needs (2G/3G/4G/LTE)
Timing and synchronization support for voice and TDM traffic
Performance and bandwidth to meet growing service needs
Software features to deliver an enhanced Quality of Experience (QoE)class of service, network resiliency, and OAM)
Juniper Networks ACX Series Universal Access Routers meet and often exceed the key requirements for a cell site
router. The ACX Series includes four fixed 1 U compact models (the ACX1000, ACX1100, ACX 2000, and ACX2100
Universal Access Routers) and a 2.5 U modular ACX4000 Universal Access Router model. ACX Series 1 U fixed models
are European Telecommunication Standards Institute (ETSI) 300 compliant, as well as environmentally hardened
and passively cooled for easy deployment where space and cooling are limited. The ACX Series supports multiple
high precision timing options (SyncE , 1588v2, etc.) to deliver the highest QoE. Junipers mobile backhaul solution also
provides comprehensive delay and jitter measurements with the unified Junos Space platform. Using the ACX Series as
a cell site router, providers can eliminate the need for external appliances deployed specifically for timing and packet
delay variation (PDV) measurements.
The ACX Series routers support TDM (T1/E1) and Ethernet (10/100/1000 copper and GbE/10GbE fiber) interfaces to
support both the legacy and evolution needs of the mobile network. Support for Power over Ethernet (PoE+) at 65
watts per port mitigates the need for additional electrical cabling for microwaves or other access interfaces. The ACX
Series is powered by Juniper Networks Junos operating system, and it supports extensive L2 and L3 features, IP/MPLS
with traffic engineering, rich network management, fault management, service monitoring and OAM capabilities, and
an open software development kit (SDK) system that allows providers to customize and integrate operations with their
own management systems.
With industry-leading performance of up to 60 Gbps and support for 10GbE interfaces, the ACX Series is well
positioned to address the growing bandwidth needs of service providers, with platforms that deliver the necessary
scale and performance needed to support multi-generation services.
Pre-Aggregation and Aggregation Router
Multiple access networks typically connect to an upstream pre-aggregation and/or aggregation network in the metro
areas before they can be handed off to regional points of presence (POPs). The key features needed at the preaggregation and aggregations segments of the network include:
High-density Ethernet
Support for versatile L2 and L3 carrier Ethernet/MPLS features
OAM and network resiliency features
Inline timing support for voice and TDM applications
The MX Series mid-range routers are ideal for pre-aggregation and aggregation layers of the network with support for
a unique pay-as-you-grow model that allows operators to scale their network resources with growing service demands
in a nondisruptive fashion. The mid-range MX Series routers include the Juniper Networks MX5 and MX80 3D Universal
Edge Routersboth in a compact 2 U form factor.
Edge Router
The edge router is typically the service or provider edge that separates the access and aggregation layers from the
service provider core. This is typically the most complex segment in a provider network with the highest demand
for control plane and service plane scalability. This is also typically the network segment where diverse access and
aggregation networks converge. Key requirements include:
High-density Ethernet
SONET and TDM interfaces for legacy applications
Scale for control plane, service plane, and data plane
System redundancy and network resiliency features
Extensive L2 and L3 IP/MPLS features to support diverse applications
L2 and L3 virtualization support (pseudowire, virtual private LAN service, L3 VPN)
Ability to receive timing from grand master and transmit out to the slave routers in the aggregation and access networks
The high-end MX Series 3D Universal Edge Routers (MX240, MX480, and MX960) have revolutionized the network
edge deployments in service provider networks with Junipers industry-leading support for three-dimensional scale for
bandwidth, subscribers, and services. These MX Series platforms support a versatile feature set for both L2 and L3 IP/
MPLS applications for both unicast and multicast traffic. With redundancy for all common system components and
a comprehensive Ethernet/MPLS OAM toolkit, the MX Series has proven to be the cornerstone for large-scale carrierclass networks.
Solution Implementation
Overview
There is no one solution that can fit all needs. The choice of a solution depends on many factors such as physical
access and geography, network segment ownership, network size, mobile service technology being used (2G/3G/4G/
LTE), and the types of traffic and extended services carried over the several segments of the network. Junipers mobile
backhaul solution can support multiple network topologies and service types from the access to the aggregation and
edge segments into the mobile packet core. For illustration purposes, we will consider one example in this guide.
In the solution described here, the ACX Series is used in the access layer as cell site routers, and the MX Series is used
for aggregation and edge routers. The sample deployment includes a L2 pseudowire solution for legacy 2G/3G/LTE
services, and MPLS L3 VPNs for LTE services on an end-to-end seamless MPLS network.
Network Topology
Figure 3 illustrates the overall network topology with IS-IS as the interior gateway protocol (IGP) in the aggregation and
access rings, and hierarchical labeled BGP between the access and aggregation rings.
Lo0: 1.1.2.1
Lo0: 1.1.10.1
Lo0: 1.1.4.1
acx2-01
[CSR]
Lo0: 1.1.1.1
23.0.1.1
mx80-3
[AG2-1]
Lo0: 1.1.14.1
23.0.1.2
mx80-2
[AG1-1]
Access
BGP AS 65001
65.1.1.1
Lo0: 1.1.9.1
mbh-acx2-02
TCA8000
Grand Master
Aggregation
BGP AS 65001
Lo0: 1.1.5.1
23.0.2.1
[PE]
mx80-3
[AG1-2]
23.0.2.2
Universal Edge
BGP AS 65002
AG2-2
mbh-mx80-1
Lo0: 1.1.7.1
Lo0: 1.1..12.1
ISIS level 1
ISIS level 2
eBGP
Figure 3: Juniper mobile backhaul solution deployment example for 2G/3G/LTE services
Configuration
IGP Setup
The access and aggregation rings are in a common BGP autonomous system (AS) (65001) and are segmented with
IS-IS IGP, with IS-IS level 1 in the access ring and IS-IS level 2 links in the aggregation. The provider edge (PE) router
is in a separate BGP AS that nicely separates the regional aggregation and access rings from the service provider core
network.
ACX2-01 (CSR) IS-IS Configuration
level 2 disable;
interface ge-0/2/0.0;
interface ge-0/2/1.0;
interface lo0.0;
MX80-2 (AG1-1) IS-IS Configuration
export export-isis;
interface ge-1/2/2.1
level 2 disable;
}
interface ge-1/2/2.2
level 1 disable;
}
interface ge-1/3/3.0
level 2 disable;
}
interface ge-1/3/4.0
level 1 disable;
}
interface lo0.0;
{
{
{
{
mbh-acx2-02
Lo0: 1.1.2.1
Lo0: 1.1.1.1
acx2-01
[CSR]
Primary 2
Lo0: 1.1.4.1
Lo0: 1.1.10.1
mx80-2
[AG1-1]
Secondary 2
Secondary 1
mx80-3
[AG2-1]
Primary 2
Secondary 2
mx80-3
[AG1-2]
[PE]
Lo0: 1.1.11.1
Secondary 1
Lo0: 1.1.5.1
Universal Edge
BGP AS 65002
AG2-2
mbh-mx80-1
Lo0: 1.1.7.1
Access
BGP AS 65001
ISIS level 1
Aggregation
BGP AS 65001
ISIS level 2
eBGP
Figure 4: RSVP tunnels with fast reroute in access and aggregation rings
10
BGP-LU is used for label distribution in the aggregation ring. BGP configuration on route reflector node AG2-1 below
includes AG1-1 as route reflector client and AG2-2 as iBGP peer. We also configure multihop BFD on the BGP sessions to
enable speedy detection of BGP session failures and allow the clients to switch to the second route reflector to restore
services quickly. In this example, we use BFD on RSVP tunnels and BGP sessions, and the BFD timers for each should
be tuned based on the network size and convergence requirements.
11
group ag1_rr {
type internal;
local-address 1.1.10.1;
export nh-self;
cluster 1.1.10.1;
peer-as 65001;
local-as 65001;
neighbor 1.1.4.1 {
family inet {
labeled-unicast {
rib {
inet.3;
}
}
}
bfd-liveness-detection {
minimum-interval 150;
multiplier 3;
session-mode multihop;
}
}
group ag2_ibgp {
type internal;
local-address 1.1.10.1;
peer-as 65001;
local-as 65001;
neighbor 1.1.11.1 {
family inet {
labeled-unicast {
rib {
inet.3;
}
}
}
bfd-liveness-detection {
minimum-interval 150;
}
}
}
BGP Configuration on the PE Router
The upstream PE router is configured in AS 65002 and has EBGP sessions with BGPLU to the aggregation routers
AG2-1 and AG2-2. Configuration snippet is shown below:
12
label-switched-path acx2-01-to-mx80-2 {
from 1.1.1.1;
to 1.1.4.1;
ldp-tunneling;
oam {
bfd-liveness-detection {
minimum-interval 100;
}
}
fast-reroute;
primary to_acx2-02;
secondary to_mx80-1 {
standby;
}
}
To keep the CSR simple and enable just the necessary prefix/label intelligence, we use LDP downstream on demand as
illustrated here. We run LDP DoD sessions from the CSR to the two aggregation nodes AG1-1 and AG1-2.
13
dod-request-policy get_dod_prefix;
interface lo0.0;
session 1.1.4.1 {
downstream-on-demand;
}
session 1.1.5.1 {
downstream-on-demand;
}
The policy get_dod_prefix determines the prefixes that the CSR needs labels for:
egress@mbh-acx2-01# show policy-options policy-statement get_dod_prefix
term 10 {
from {
prefix-list dod_prefix;
}
then accept;
}
[edit]
regress@mbh-acx2-01# show policy-options prefix-list dod_prefix
1.1.10.1/32;
1.1.11.1/32;
1.1.14.1/32;
This completes the base IGP, BGP, and label transport configuration for the access, aggregation, and edge network.
The next step is to map services on top of this network architecture. Before we enable the services, we will look at the
timing configuration on this network.
Timing Configuration
The timing grand master can be set up in the aggregation or at the edge network, depending on the services model in
the MSP network. In our example, we have a grandmaster Juniper Networks TCA8000 Timing Server connected to the
PE router, and we use 1588v2 timing. The PE router then transmits this timing to the downstream network nodes in the
aggregation and access layers.
Configuration the configuration of the 1588-2008 timing protocol also know as Precision timing protocol (PTP), the
CSR is configured as a slave and is receiving timing on interface ge-0/2/0.0 from the master connected to AG2-1
(65.1.1.2).
14
Service Configuration
Layer 3 VPN Service Model for LTE Traffic
In this deployment solution, we configure L3 VPN service at the CSR for LTE traffic (see Figure 5). L3 VPN service
has several benefits for LTE application in the mobile backhaul. It is an Layer 3 multipoint service that relies on L3
routing and fast convergence for service restoration and eliminates the need for L2 loop prevention protocols. This
deployment model also allows low latency X2 traffic communication between eNB nodes to be turned around at the
first aggregation PE router. Configuration and addition of cell site routers is simple and does not cause any service
reconfiguration on existing nodes.
1588v2 Grand Master
65.1.1.2
TCA8000
Grand Master
65.1.1.1
Lo0: 1.1.9.1
mbh-acx2-02
Lo0: 1.1.2.1
Lo0: 1.1.10.1
Lo0: 1.1.4.1
acx2-01
[CSR]
Lo0: 1.1.1.1
Lo0: 1.1.14.1
23.0.1.2
mx80-2
[AG1-1]
Access
BGP AS 65001
23.0.1.1
mx80-3
[AG2-1]
23.0.2.1
Aggregation
BGP AS 65001
Lo0: 1.1.5.1
PE
Lo0: 1.1.11.1
mx80-3
[AG1-2]
23.0.2.2
Universal Edge
BGP AS 65002
AG2-2
mbh-mx80-1
Lo0: 1.1.7.1
Lo0: 1.1..12.1
MP-IGBP CSR to AG1-1 for L3VPN on CSR
MP-EBGP for L3VPN Service [Option C 2547 bis on AG1-1 and PE]
ISIS level 1
ISIS level 2
eBGP
15
We configuring Multiprotocal Border Gateway Protocol (MP-BGP) for VPN label exchange between CSR and AG1-1 and
AG1-2 as shown below:
16
group option_c {
type external;
neighbor 1.1.4.1 {
multihop {
ttl 64;
}
local-address 1.1.14.1;
family inet-vpn {
unicast;
}
peer-as 65001;
local-as 65002;
}
neighbor 1.1.5.1 {
multihop {
ttl 64;
}
local-address 1.1.14.1;
family inet-vpn {
unicast;
}
peer-as 65001;
local-as 65002;
}
}
17
mbh-acx2-02
Lo0: 1.1.2.1
Lo0: 1.1.10.1
Lo0: 1.1.4.1
acx2-01
[CSR]
23.0.1.1
mx80-3
[AG2-1]
Lo0: 1.1.14.1
23.0.1.2
mx80-2
[AG1-1]
Access
BGP AS 65001
Lo0: 1.1.1.1
23.0.2.1
Aggregation
BGP AS 65001
Lo0: 1.1.5.1
PE
Lo0: 1.1.11.1
mx80-3
[AG1-2]
23.0.2.2
Universal Edge
BGP AS 65002
AG2-2
mbh-mx80-1
Lo0: 1.1.7.1
Lo0: 1.1..12.1
Point-to-Point PW L2VPN Service
LDP DoD for Label Distribution in Access Ring
ISIS level 1
ISIS level 2
eBGP
l2circuit {
neighbor 1.1.14.1 {
interface ge-0/1/7.1 {
virtual-circuit-id 123;
no-control-word;
}
}
neighbor 1.1.14.1 {
interface t1-0/0/0.0 {
virtual-circuit-id 100;
standby;
}
}
}
}
18
l2circuit {
neighbor 1.1.1.1 {
interface ge-3/0/2.1 {
virtual-circuit-id 123;
no-control-word;
}
}
}
l2circuit {
neighbor 1.1.1.1 {
interface t1-4/0/0:1:1.0 {
virtual-circuit-id 100;
}
}
}
CFM Configuration for the VLAN Pseudowire
This section provides the configuration for enabling a connectivity fault management (CFM) continuity check and
enables quick failure detection along the pseudowire path. The pseudowire at the CSR can also be configured with a
remote backup to which traffic can be redirected in the event the primary path pseudowire fails.
protocols {
oam {
ethernet {
connectivity-fault-management {
maintenance-domain md6 {
level 6;
maintenance-association ma6 {
continuity-check {
interval 10s;
}
mep 2 {
interface ge-0/1/7.0;
direction up;
auto-discovery;
}
}
}
maintenance-domain md0 {
level 0;
maintenance-association ma0 {
continuity-check {
interval 100ms;
}
mep 100 {
interface ge-2/2/0.0;
auto-discovery;
}}}}}}}}
With this section, the basic configuration for Layer 3 and Layer 2 VPNs over a seamless MPLS network is complete.
These services can be used alone or in combination to meet the service needs of the MSP across multi-generational
networks (2G/3G/4G/LTE)
19
Summary
Over time, network access has evolved from circuits to packets, from TDM to IP/Ethernet, and from wireline to wireless.
This has resulted in multiple access networks for different applications with many touch points, leaving operators
with an obvious management challenge. As more and more access connections require wireless support, and with the
proliferation of mobile-to-mobile and mobile-to-machine applications, the challenges facing mobile operators are ever
on the rise. What is required is a network architecture and network elements that can support multiple models to meet
both legacy and evolutionary needs.
One of the main advantages of using IP-based networks is the ability to transport different traffic types over a common
IP/MPLS-based infrastructure in addition to providing QoS guarantees and meeting security requirements. But as MSPs
transition to an all IP/MPLS infrastructure, they will need to support both legacy and next-generation service needs.
Junipers high-performance mobile backhaul solutionACX Series Universal Access Routers, MX Series 3D Universal
Edge Routers, and Junos Space unified network management systemis designed to meet the growing bandwidth
and service needs for these multiple 2G/2.5G/3G/4G generations. With Junipers seamless MPLS solution powered
by a single Junos OS and a comprehensive OAM toolkit across the various network elements, this solution enables
operational efficiency for large-scale MSP networks today and into the future.
Appendixes
Introduction to Mobile Backhaul Technologies
Mobile technologies are classified into different generations (referred to as 2G/2.5G/3G/4G). Each generation of mobile
technology provides users with enhanced services, higher speeds, and better network capacity. Different bodies and
forums such as Third-Generation Partnership Project (3GPP/3GPP2), European Telecommunications Standardization
Institute (ETSI), and International Telecommunication Union (ITU) recommend, approve standards, and advance the
various technologies underlying each generation.
The main components of a Radio Access Network (RAN) are described briefly in the following sections. The
terminology used for these components differs based on the technology that is used. Table 1 lists the different naming
conventions used in the case of each technology.
BTS
A base transceiver station (BTS) is a device that can provide communication between mobile user equipment and a
mobile network. The BTS communicates with mobile user device over the air interfaces. There can typically be as many
as 50 BTS devices controlled by one base station controller (BSC). (This document uses the generic term BS or RAN
BS to refer to a cell tower/BTS.)
BSC
The main function of a BSC is to communicate and control multiple BTS devices over either the Abis or Iub
interface. The BSC also controls hand-offs that occur as a result of mobile devices moving between cell sites, and
it communicates with the mobile core (with the type of communication depending on the interface to core that in
turn depends on the technology). A single 2G BSC can typically control as many as 50 BTS devices, while a 3G radio
network controller (RNC) can control 200 NodeBs and up to 800 base stations per BSC/RNC in a 2.5G/3G network.
(This document uses the generic term RNC or RAN NC to refer to a BSC.)
20
Type of
Technology
RAN Components
Example of Role
2G
Global System
for Mobile
Communications
(GSM)
BTS
BSC
MSC
2.5G
General Packet
Radio Service
(GPRS)
BTS
SGSN
GGSN
BSC + PCU
3G
Evolution-Data
Optimized (EVDO)
BTS
RNC
PDSN
Universal mobile
telecommunications
system (UMTS)
Terrestrial Radio
Access Network
(UTRAN)
NodeB
RNC
MSC
eNodeB
SGW (Serving Gateway)
MME (Mobility Management
Entity)
Public data network (PDN)
Gateway
Worldwide
Interoperability for
Microwave Access
(WiMAX)
BS
Access service network
gateway (ASN GW)
Connectivity service network
gateway (CSN GW)
Generation
4G
Mobile Backhaul
BS
BSC
Figure 7: Overview of a generic mobile backhaul
The generic model for the newer backhaul networks consists of a cell, hub sites, or both connected to aggregation
devices that in turn can either belong or be connected to a metro network. Figure 8 shows the different subcomponents
of the mobile backhaul network. The most commonly proposed metro network for 3G/4G technologies is an Ethernetbased services network. This network should be capable of providing multi-access to different Layer 2 technologies
such as Frame Relay/ATM/TDM, and IP.
21
Another perspective of the mobile backhaul could lead to following classification of functionality:
Mobile Backhaul
Cell Site Devices
Hub/Aggregation
Site Devices
Metro Network
22
APAC Headquarters
EMEA Headquarters
Phone: 35.31.8903.600
or 408.745.2000
Phone: 852.2332.3636
Fax: 408.745.2100
Fax: 852.2574.7803
Fax: 35.31.8903.601
www.juniper.net
Copyright 2012 Juniper Networks, Inc. All rights reserved. Juniper Networks, the Juniper Networks logo, Junos,
NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other
countries. All other trademarks, service marks, registered marks, or registered service marks are the property of
their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper
Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice.
8020015-001-EN
Feb 2012
23