Beruflich Dokumente
Kultur Dokumente
Control unit
Operating instructions
Contents
Safety............................................................................................... 4
General instructions
Safety instructions
4
4
Description....................................................................................... 5
Purpose and application
Function
Light control
Brightness control
Motion detection
Design
5
5
5
5
5
5
Installation........................................................................................ 6
Installation notes
Connection examples
Light control
Brightness control of luminaire group 1 (with one sensor)
Brightness control of luminaire group 1 and motion detection
(with two sensors)
Brightness control of luminaire groups 1, 2 and 3 and expanded
motion detection (with three sensors)
Connections
Testing the pushbutton wiring
System and fault messages
Behaviour after a power failure
6
7
7
8
9
10
11
11
12
12
Operation....................................................................................... 13
Symbols
Principle of closed-loop and open-loop control
Performing a reset
Defining the luminaire groups
Testing the luminaire group assignment
Switching on and off the luminaires
Changing the brightness manually
Storing and calling up a lighting scene
Locking luminaire group assignment and scene storage
Adjusting the switch-off delay time
13
13
14
14
16
16
17
17
18
18
Appendix........................................................................................ 19
Technical data
Dimensioned drawing
19
20
DALI RC BASIC SO
Safety
Safety
General instructions
The control unit must only be installed and put into operation by a qualified electrician.
The applicable safety regulations and accident prevention regulations must be observed.
Safety instructions
WARNING!
Exposed, live cables.
Danger of electric shock!
CAUTION!
Destruction of the control unit and other devices through incorrect mounting!
Do not connect additional DALI supplies or DALI control units in the system to
avoid exceeding the max. permissible total current of 250 mA.
Do not exceed the maximum total line lengths and the corresponding line crosssections.
VII 2009
DALI RC BASIC SO
Description
Description
Purpose and application
The DALI RC BASIC SO control unit can be used for both scene-based open-loop
control and daylight/presence-dependent closed-loop control.
The control unit can control up to 64 DALI units (ECG or converters). The functions
are operated on standard pushbuttons.
Function
Light control
The control unit enables the variable formation of 4 luminaire groups whose individual
brightness settings can be used to set up and store 4 scenes (lighting situations in a
room).
Brightness control
In scene 1, the brightness of up to 3 luminaire groups can be controlled by connecting light sensors (DALI LS BASIC): The sensors measure the brightness in the area
requiring control and keep it to an adjustable set value by introducing artificial light
according to the amount of daylight available.
Motion detection
In addition, by connecting combined light and motion sensors (DALI LS/PD BASIC), all
luminaire groups can be switched on and off depending on the presence of persons.
Design
The control unit is made up of the following components:
Connection terminals (A)
Reset button (B)
Adjusting screw for switch-off delay time (C)
LED display (D)
Housing (E)
A
1
9
10
11
12
A
5
13 14
15
16
C
D
17
18
19
20
25 26
27
28
A
VII 2009
21 22
29
30
23
24
31
32
A
5
DALI RC BASIC SO
Installation
Installation
Installation notes
A maximum of 64 DALI units can be connected.
A maximum of 6 sensors can be connected, either all on a single LS input or dis-
The control unit contains the power supply for the DALI interfaces and the supply
voltage for the sensors.
If the DALI lines are overloaded for a long period or short-circuited, the DALI inter-
face switches to high impedance until the fault is eliminated. The green On LED
goes out and the red Fault LED lights up. The fault contact is not closed in this
case.
The motion sensors are automatically detected when the mains voltage of the con-
trol unit is connected, but their removal is only detected after power is disconnected.
The light sensors are always detected.
All motion sensors connected to the PD input act in parallel (detection area extension). After the mains supply is connected, motion detection is suppressed for 1
minute.
Standard pushbuttons can be used for operation (make contacts with basic insula-
tion). To make full use of the functionality, a 5-fold pushbutton field is required (e.g.
DALI WCU 5 BASIC W).
An optional signal lamp may be connected. Other connections are possible using
the floating contact.
By using DALI converters, it is also possible to transfer the functions of the control
unit to existing 1...10V / 0...10V systems.
VII 2009
DALI RC BASIC SO
Installation
Connection examples
Light control
No sensor is connected.
Signal lamp
(optional)
To the DALI
operating devices
Pushbuttons
VII 2009
DALI RC BASIC SO
Installation
Brightness control of luminaire group 1 (with one sensor)
Signal lamp
(optional)
To the DALI
operating devices
Pushbuttons
VII 2009
DALI RC BASIC SO
Installation
Signal lamp
(optional)
To the DALI
operating devices
Pushbuttons
VII 2009
DALI RC BASIC SO
Installation
lighting
Luminaire group 4: light control with motion detection (calling up of lighting scene 1)
Signal lamp
(optional)
To the DALI
operating devices
Pushbuttons
10
VII 2009
DALI RC BASIC SO
Installation
Connections
Terminal
Function
1/9 (DA+)
2/10 (DA)
3/4 (0V)
5/6/7 (PD)
8/16 (Vcc)
11/12 (0V)
13/14/15
(LS1, LS2, LS3)
17/25 (fault)
18/26
19/27 (L)
20/28 (N)
21/22/23/24/29
Pushbutton inputs (make contacts), < 5 V DC
(T1 T4, master)
30/31/32 (0V)
Task
Result
Press button 1 to 4.
VII 2009
11
DALI RC BASIC SO
Installation
State
Meaning
Green "On"
LED
Flashes
On
Yellow
"Send"
LED
On
Red "Fault"
LED
Flashes
On
12
VII 2009
DALI RC BASIC SO
Operation
Operation
Symbols
Switch on
Luminaire on
Switch off
Luminaire off
Pushbutton on
the luminaire
Brightness with
automat. control
Short press
(< 0.5 s)
Long press
(0.5 4 s)
Motion?
no
yes
Scene 1
no
Button 1 pressed?
no
yes
Button 2 pressed?
no
yes
no
yes
Button 4 pressed?
no
yes
Scene 3
Scene 2
Button 3 pressed?
Scene 4
10 min
no
min.
yes
Motion?
1-32 min
no
min.
16 s*
yes
VII 2009
13
DALI RC BASIC SO
Operation
Performing a reset
In the basic setting, all luminaires are assigned to luminaire group 1 and scenes 1 to 4
are predefined.
Note: In the following cases, the control unit automatically resets the system when
the mains voltage is applied:
Proceed as follows:
Step
Task
Result
14
Task
Result
VII 2009
DALI RC BASIC SO
Operation
Step
3
Task
Result
VII 2009
15
DALI RC BASIC SO
Operation
Step
9
Task
Result
When adding or removing DALI units, the entire procedure needs to be repeated and
the existing assignments of all units that have already detected must each be confirmed via the central button.
Task
Result
Press pushbuttons 1
to 4.
16
VII 2009
DALI RC BASIC SO
Operation
Task
Set the brightness of the luminaire groups; see "Changing the brightness
manually".
Note:
The brightness values stored in lighting scene 1 (button 1) are the setpoints for the
brightness control.
The lighting scene storage function can be locked; see Locking luminaire group
assignment and scene storage.
To call up a lighting scene: Use a short press.
VII 2009
17
DALI RC BASIC SO
Operation
Task
Result
Yellow
"Send" LED
Off
Red
"Fault"
LED
Lock mode
Off
On
Off
Off
On
On
On
18
VII 2009
DALI RC BASIC SO
Appendix
Appendix
Technical data
Operating voltage
Power consumption
Fuse
Connection terminals
Screw terminals
VII 2009
100 m
Design
Insulated casing
Mounting
Operating temperature
0 C ... +45 C
Protection type
IP 20
Protection class
II (double insulated)
Pollution severity
Weight
Approx. 550 g
Dimensions (L x W x H)
140 x 90 x 61 mm (8 HP)
19
DALI RC BASIC SO
Appendix
61
Dimensioned drawing
140
90
20
VII 2009
VII 2009
DALI_RC_BASIC_SO_0907en_we1.01.indd
OSRAM GmbH
Kunden Service Center
Customer-Service-Center (CSC)
Steinerne Furt 62
86167 Augsburg
Germany
Tel : +49 (0) 1803 677 - 200
(kostenpflichtig / charges apply)
Fax.: +49 (0) 1803 677 - 202
www.osram.com
www.osram.de
40503006549736
4050300654973