Beruflich Dokumente
Kultur Dokumente
0
Database version
2016.9.5.13.30
Date
26/09/2016
Design Specifications
Anchor
Anchor system
Injection resin
Fixing element
Anchorage depth
Design Data
Page 1
C-FIX 1.34.0.0
Database version
2016.9.5.13.30
Date
26/09/2016
Input data
Design method
Base material
Concrete condition
Temperature range
Reinforcement
Drilling method
Installation type
Annular gap
Type of loading
Base plate location
Base plate geometry
Profile type
Design actions *
NSd
kN
VSd,x
kN
VSd,y
kN
MSd,x
kNm
MSd,y
kNm
MT,Sd
kNm
127.00
0.00
0.00
0.00
0.00
0.00
Tensile action
kN
Shear Action
kN
Shear Action x
kN
Shear Action y
kN
127.00
0.00
0.00
0.00
Force:
0.00
0.0
127.00
0.00
Tension
Compression
N/mm
kN , X/Y position ( 0 / 0 )
kN , X/Y position ( 0 / 0 )
Action
kN
Capacity
kN
Utilisation N
%
Steel failure *
127.00
130.67
97.2
127.00
127.19
99.8
127.00
127.80
99.4
Steel failure
( NRd,s )
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 2
C-FIX 1.34.0.0
Database version
2016.9.5.13.30
Date
26/09/2016
Eq. (5.1)
NRk,s
kN
Ms
NRd,s
kN
NSd
kN
N,s
%
196.00
1.50
130.67
127.00
97.2
Anchor no.
N,s
%
Group N
Decisive Beta
97.2
N,s;1
Eq. (5.2)
Eq. (5.2a)
Eq. (5.2c)
Eq. (5.2d)
Eq. (5.2e)
Eq. (5.2f)
Eq. (5.2g)
Eq. (5.2h)
Eq. (5.2i)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 3
C-FIX 1.34.0.0
Database version
2016.9.5.13.30
Date
26/09/2016
NRk,p
kN
Mp
NRd,p
kN
NSd
kN
N,p
%
190.79
1.50
127.19
127.00
99.8
Anchor no.
N,p
%
Group N
Decisive Beta
99.8
N,p;1
Eq. (5.3)
Eq. (5.3a)
Eq. (5.3c)
Eq. (5.3d)
Eq. (5.3e)
NRk,c
kN
Mc
NRd,c
kN
NSd,
kN
N,c
%
191.71
1.50
127.80
127.00
99.4
Anchor no.
N,c
%
Group N
Decisive Beta
99.4
N,c;1
(5.9a)
t = 12 mm
None
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 4
C-FIX 1.34.0.0
Database version
2016.9.5.13.30
Date
26/09/2016
Technical remarks
All data and information in the software is based on fischer products and common engineering knowledge. Please
check all the proof results against local valid standards and approvals.
As fischer is not the design office, the attached is no guarantee for incorrect input or assumptions. Any
recommendations have to be approved by the building-authority or project engineer. Results are valid only for
anchor system calculated in the attached. If any part of the system is changed, it will invalidate this report and new
calculations would be required.
The transmission of the anchor loads to the supports of the concrete member shall be shown for the ultimate limit state and
the serviceability limit state; for this purpose, the normal verifications shall be carried out under due consideration of the
actions introduced by the anchors. For these verifications the additional provisions given in the current design method shall
be taken into account.
As a pre-condition the anchor plate is assumed to be flat when subjected to the actions. Therefore, the plate must be
sufficiently stiff. The C-Fix anchor plate design is based on a proof of stresses and does not allow a statement about
the stiffness of the plate. The proof of the necessary stiffness is not carried out by C-Fix.
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 5
C-FIX 1.34.0.0
Database version
2016.9.5.13.30
Date
26/09/2016
Installation data
Anchor
Anchor system
Injection resin
Fixing element
Accessory
Alternative cartdriges
Art.-No. 93049
Art.-No. 519406
Art.-No. 96448
Art.-No. 48983
Art.-No. 511118
Art.-No. 93286
By job site.
Art.-No. 1495
Art.-No. 511961
Art.-No. 504229
Art.-No. 508831
Art.-No. 512080
Installation details
Thread diameter
Drill hole diameter
Drill hole depth
Anchorage depth
Drilling method
Drill hole cleaning
Installation type
Annular gap
Maximum torque
Socket size
Base plate thickness
Total fixing thickness
Volume of resin per drill
hole
M 20
d0 = 24 mm
h2 = 241 mm
hef = 229 mm
Hammer drilling
2 times blowing (compressed air),
2 times brushing,
2 times blowing (compressed air)
Push-through installation
Annular gap filled
Tinst,max = 120.0 Nm
30 mm
t = 12 mm
tfix = 12 mm
58 ml/29 scale divisions
Not available
t = 12 mm
df=26 mm
Attachment
Profile type
None
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 6
C-FIX 1.34.0.0
Database version
2016.9.5.13.30
Date
26/09/2016
Anchor coordinates
Anchor no.
1
x
mm
y
mm
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 7