Sie sind auf Seite 1von 104

Buyer: Olga Simiacov (olga.simiacov@ratb.

ro)
Transaction ID: 1V0226867H4668431

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Foreword
The main objective of these tutorials is to give you a kick start using SolidWorks. The approach to
write this tutorial is based on what is the most important knowledge you should know and what is
commonly tool used. You will learn step by step by working on it. These tutorials will teach you
the basic skills of using Solidworks in your daily design works. Even this tutorials didnt have full
explanations of tools that Solidworks have but dont worry you will master it along the way, as I
did.
If you have any questions about these tutorials, drop your mail to
support@solidworkstutorials.com

Solidworks 2010 Tutorials: Beginner


http://www.solidworkstutorials.com
2010 solidworkstutorials.com , All rights reserved.
This publication is copyright under the solidworkstutorials.com
All rights reserved. Apart from any fair dealing for the purpose of private study, research, criticism, or review, as permitted
under the Copyright Designs and Patents Act 1988, no part may be reproduced, stored
in a retrieval system, or transmitted in any form or by any means, electronic, electrical, chemical, mechanical,
photocopying, recording or otherwise, without the prior permission of the copyright owners. Unlicensed multiple copying
of this publication is illegal. Inquiries should be addressed to: support@solidworkstutorials.com
If this guide is distributed with software that includes an end-user agreement, this guide, as well as the software described
in it, is furnished under license and may be used or copied only in accordance with the terms of such license. Except as
permitted by any such license, no part of this guide may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of
solidworkstutorials.com. Please note that the content in this guide is protected under copyright law even if it is not
distributed with software that includes an end-user license agreement. The content of this guide is furnished for
informational use only, is subject to change without notice, and should not be construed as a commitment by
solidworkstutorials.com. Solidworkstutorials.com assumes no responsibility or liability for any errors or inaccuracies that
may appear in the informational content contained in this guide. Please remember that existing artwork or images that
you may want to include in your project may be protected under copyright law. The unauthorized incorporation of such
material into your new work could be a violation of the rights of the copyright owner. Please be sure to obtain any
permission required from the copyright owner. Any references to company names in sample templates are for
demonstration purposes only and are not intended to refer to any actual organization.
The publishers are not responsible for any statement made in this publication. Data, discussion, and conclusions
developed by the Author are for information only and are not intended for use without independent substantiating
investigation on the part of the potential users. Opinions expressed are those of the Author and are not necessarily those
of the Institution of Mechanical Engineers or its publishers.

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Solidworks Tutorials: Beginner Table of contents

www.solidworkstutorials.com

Table of contents
Beginner Part 1: My First Solid

1
The big picture how SolidWorks works, it starts
with a simple editable sketch. From this sketch a
feature build the solid. From this solid it
produces drawing...
Beginner Part 2: Sketching

Sketch is the base of your part, its a good


practice to master sketching in SolidWorks...

10

Beginner Part 3: Turning Parts

23
Some parts such as pins and shafts can be
manufacture by turning process on lathe
machine, we can create turning part by revolving
it sketch on it axis...
Beginner Part 4: Hole Wizard

30
Hole Wizard is used for creating predefined and
standard holes such as counter bore hole,
counter sunk hole, screw clearance hole and
many more...
Beginner Part 5: Pattern

40
Pattern (or some called array) is used to repeat
features in linear arrangement or circular
arrangement. Its good to know how to optimize
these tool, it help you make your part faster and
easier...
Beginner Part 6: Assembly Parts

60
Assembly is a part of design process, it show how
all designed parts work together as a single
unit...
Beginner Part 7: Detailing Drawing

80
Once solid parts created we need to transfer it to
engineering drawing so the others can
understand your parts

Solidworks Tutorials: Beginner Table of contents

ii

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 1: My First Solid

www.solidworkstutorials.com

Beginner Part 1: My First Solid


The big picture how SolidWorks works, it starts with a simple
editable sketch. From this sketch a feature build the solid. From
this solid it produces drawing... Lets begin your first solid...

1.

Click New

2.

Click Front Plane, insert sketch on plane by click Sketch.

In this tutorial you will make this


3.
bracket, start from sketch and build
features.

4.

Beginner Part 1: My First Solid

Click Sketch

, click Part

, OK.

, click

Corner Rectangular
. Start first point at origin and
click another point at top right side.

Click Smart Dimension


, click top edge set
dimension to 3in and click right edge set dimension to 2in.

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 1: My First Solid

www.solidworkstutorials.com

5.

Beginner Part 1: My First Solid

To build features, click Extruded Boss/Base

, set D1 to

0.10in

and

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 1: My First Solid

www.solidworkstutorials.com
6.

Click on front face of the part, click Normal To.

7.

Click Circle

, sketch circle on face

Click Smart Dimension


, click circle edge and set
diameter to 0.6in. For circle positioning click circle edge and
vertical part edge set to 0.5in. Click circle edge again and
click horizontal part edge set to 0.5in.

Beginner Part 1: My First Solid

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 1: My First Solid

www.solidworkstutorials.com

8.

Click Extruded Cut

All

Beginner Part 1: My First Solid

, change Direction 1 to Through

and

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 1: My First Solid

www.solidworkstutorials.com
9.

Click on front face and select Sketch

.
Select Corner Rectangular
top right edge to center.

10. Click Smart Dimension


dimension to 2in and 1in.

Beginner Part 1: My First Solid

sketch rectangular from

, set rectangular

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 1: My First Solid

www.solidworkstutorials.com

Click
Extruded Cut

and select Through All

and

11. Click on front face and select Sketch

. Click
Corner Rectangular
and sketch rectangular start
form bottom left edge to right edge.

Beginner Part 1: My First Solid

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 1: My First Solid

www.solidworkstutorials.com

Click
Smart Dimension and set rectangular height to 0.1in.

12. Click Extruded Boss/Base

Style and select Isometric.

Beginner Part 1: My First Solid

set Direction 1 to 0.5in

and

. Click Display

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 1: My First Solid

www.solidworkstutorials.com

13. Click Fillet

, check Full preview

add fillet to all edges

Beginner Part 1: My First Solid

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 1: My First Solid

www.solidworkstutorials.com

and

14. Save
it?

the part as Bracket and youre done! Simple isnt

Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com

Beginner Part 1: My First Solid

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

Beginner Part 2: Sketching


Sketch is the base of your part, its a good practice to master
sketching in SolidWorks...

1.

Click New

2.

Click Front Plane, insert sketch on plane by click Sketch.

3.

Click Sketch

, click Part

, OK.

In this tutorial you will make this


box, start from sketch and build
features. Youll learn how to use
sketch tools to build this part.

, click

Corner Rectangular
. Start first point at origin and
click another point at top right side.

4.

Beginner Part 2: Sketching

Click Smart Dimension


, click top edge set
dimension to 2in and click right edge set dimension to 2in.

10

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com
5.

To build features, click Features>Extruded Boss/Base

, set D1 to 0.50in

and

Beginner Part 2: Sketching

11

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

Beginner Part 2: Sketching

www.solidworkstutorials.com
6.

Click on front face of the part, click Normal To.

7.

Click on front face and click Sketch.

12

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

8.

Click Offset Entities

, set to 0.1in and check

Reverse box

9.

Beginner Part 2: Sketching

Click Extruded Cut

and

, change D1 to 0.4in.

13

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com
10. Click on side face, click Sketch.

11. While pressing Ctrl key select inner left and right edge.

Click

Convert Entities

12. Select Centerline from line menu


,
sketch a centerline midpoint to midpoint of both converted

Beginner Part 2: Sketching

14

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

edges.
13. Click sketched centerline

and click Offset Entities.

Beginner Part 2: Sketching

15

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

Set Parameter, D to 0.3in check Bi-directional and

14. Now click Trim Entities


to remove excess line,
before make any cut make sure under option Trim to

closest is selected.
Trim extra line as
below sketch. Answers Yes if notification appear.

15. Click View Orientation>Isometric.

16. Click Features>Extruded Boss/Base


, for Direction 1,
click Reverse Direction (green box) and set D1 to 0.1in.

Beginner Part 2: Sketching

16

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

and

Beginner Part 2: Sketching

17

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com
17. Click on front face and click Normal To.

18. Click on front face and click Sketch.

Beginner Part 2: Sketching

18

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

19. Click Circle,

sketch circle at left edge.

20. Click Smart Dimension,


below sketch.

21. Click on sketched circle,

Copy Entities.

Beginner Part 2: Sketching

dimension sketch as

click

Set delta x

19

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

to 0.3in

and

22. Click Centerline,


sketch centerline
across front face and make sure it starts at midpoint left edge
and midpoint right edge and

23. While press Ctrl key, select both sketched circle and click
Mirror Entities
, on Mirror Option click
Mirror about: box, and select centerline

Beginner Part 2: Sketching

20

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

and
24. Click Extruded Cut,

and set D1 to 0.1in

25. Click View Orientation>Back,

Beginner Part 2: Sketching

and

21

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com
and click on back face and click Sketch.

26. Click Sketch>Circle,

sketch circle at lower left edge.

Click Smart

Dimension
sketch below.

and dimension sketched circle as

and

Beginner Part 2: Sketching

22

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

27. Click on sketched circle,

and click

Linear Sketch Pattern


and on
Direction 1 set D1 to 1.2in and on Direction 2, change # to
2 and set D2 to 1.2in and

Beginner Part 2: Sketching

23

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 2: Sketching

www.solidworkstutorials.com

28. Click Features>Extruded Cut,

and set direction to

Through All
Click View Orientation>Isometric.

29. Save
it?

and

the part as Sketch and youre done! Simple isnt

Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com

Beginner Part 2: Sketching

24

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 3: Turning Part

www.solidworkstutorials.com

Beginner Part 3: Turning Part


Some parts such as pins and shafts can be manufacture by
turning process on lathe machine, we can create turning part by
revolving it sketch on it axis...

In this tutorial you will make this


pin, start from sketch and build
solid body by revolve it sketch on
axis. Youll learn how to use
revolved boss/base and revolved
cut to build this part.

1.

Click New,

click Part,

OK.

2.

Click Front Plane, insert sketch on plane by click Sketch.

3.

Click on Line,
sketch a closed loop start at origin, sketch
as sketch below end back at origin.

and

4.

Click Smart Dimension


sketch below.

and
5.

Beginner Part 3: Turning Part

and dimension sketch as

Click Features>Revolved Boss/Base,


and click on bottom line as it axis.

25

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 3: Turning Part

www.solidworkstutorials.com

and

6.

Beginner Part 3: Turning Part

Click View Orientation>Front


and click Front Plane and click Sketch.

26

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 3: Turning Part

www.solidworkstutorials.com

7.

Click Corner Rectangle,


and sketch rectangle overlap
on solid body as sketched below.

and

8.

Click Smart Dimension


sketched below.

9.

To view solid body axis, click View>Temporary Axes.

and dimension sketch as

10. To make second undercut, click Features>Revolved Cut


and select temporary axes as it axis

Beginner Part 3: Turning Part

27

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 3: Turning Part

www.solidworkstutorials.com

and

Beginner Part 3: Turning Part

28

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 3: Turning Part

www.solidworkstutorials.com
11. To hide temporary axes, click View>Temporary Axes.

12. Save

the part and youre done! Simple isnt it?

Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com

Beginner Part 3: Turning Part

29

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 4: Hole Wizard

www.solidworkstutorials.com

Beginner Part 4: Hole Wizard


Hole Wizard is used for creating predefined and standard holes
such as counter bore hole, counter sunk hole, screw clearance
hole and many more...

In this tutorial you will add


counterbore, countersink and tap
holes to this plate by using Hole
Wizard tools.

1.

Click New,

2.

Click Top Plane, insert sketch on plane by click Sketch.

3.

Click on Corner Rectangle,


origin.

and

4.

Beginner Part 4: Hole Wizard

OK.

sketch a rectangle start at

Click Smart Dimension


sketch below.

and
5.

click Part,

and dimension sketch as

Click Features>Extruded Boss/Base,


set D1 to 1in

on Direction 1

30

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 4: Hole Wizard

www.solidworkstutorials.com

6.

7.

Beginner Part 4: Hole Wizard

and
.
Click on top face and click Normal To.

Click Features>Hole Wizard


on Hole Type, select
Counterbore, Standard to Ansi Inch, Type to Socket Head
Cap Screw, Size to #10, Fit to Normal and End Condition
to Through All.

31

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 4: Hole Wizard

www.solidworkstutorials.com

For positions placement for this counterbore hole, click on


Positions tab.
more positions at each edge.

Beginner Part 4: Hole Wizard

Now click three

32

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 4: Hole Wizard

www.solidworkstutorials.com

8.

Click on Smart Dimensions,


click on center point
of counterbore hole and click left edge, set dimension to
0.5in.

Continue dimensioning as sketched below.

9.

and
.
For adding countersink at center, click on top face and click
on Hole Wizard

Beginner Part 4: Hole Wizard

33

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 4: Hole Wizard

www.solidworkstutorials.com

On Hole Type, select Countersink, Standard to Ansi Inch,


Type to Flat Head Screw (100), Size to #10, Fit to Normal
and End Condition to Through All.
10. For positions placement for this countersink holes, click on
Positions tab.
more positions at center.

Beginner Part 4: Hole Wizard

Now click three

34

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 4: Hole Wizard

www.solidworkstutorials.com

11. Click on Smart Dimensions,


click on center point
of countersink hole and click left edge, set dimension to
2.5in.

Continue dimensioning as sketched below.

and
.
12. For adding center tap hole, click on top face at center and
click Hole Wizard.

Beginner Part 4: Hole Wizard

35

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 4: Hole Wizard

www.solidworkstutorials.com

On Hole Type, select Tap, Standard to Ansi Inch, Type to


Tapped hole, Size to 1/2-13, End Condition to Through
All.
13. For positions placement for this tap hole, click on Positions
tab.
There is another style to
positions hole wizard is define it position by sketch, let try it.

Click on Centerline,
Sketch a
horizontal line start at midpoint of left edge to midpoint left

Beginner Part 4: Hole Wizard

36

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 4: Hole Wizard

www.solidworkstutorials.com
edge. Press Esc to end sketch centerline.

14. Click and drag tap center to midpoint of centerline.

and
.
15. Click View Orientation>Isometric. Done.

Beginner Part 4: Hole Wizard

37

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 4: Hole Wizard

www.solidworkstutorials.com

16. Save

the part as Plate1 and youre done! Simple isnt it?

Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com

Beginner Part 4: Hole Wizard

38

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com

Beginner Part 5: Pattern


Pattern (or some called array) is used to repeat features in linear
arrangement or circular arrangement. Its good to know how to
optimize these tool, it help you make your part faster and easier...

1.
In this tutorial you will add multiple 2.
features as linear pattern and
circular pattern using pattern tools.

3.

Click New,

Click on Corner Rectangle,


origin.

Beginner Part 5: Pattern

sketch a rectangle start at

Click Smart Dimension


sketch below.

and
5.

OK.

Click Top Plane, insert sketch on plane by click Sketch.

and

4.

click Part,

and dimension sketch as

Click Features>Extruded Boss/Base,


set D1 to 1in

on Direction 1

39

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

Beginner Part 5: Pattern

www.solidworkstutorials.com

6.

and
.
Click on top face and click Normal To.

7.

Click on top face and click Sketch.

40

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com

Click on Circle

and sketch a circle on top face and

8.

Click on Smart Dimension


sketched circle as sketch below.

9.

Click Features>Extruded Cut

Through All.

and dimension

on Direction 1 set to

and

10. Click Features>Hole Wizard


on Hole Type, select
Counterbore, Standard to Ansi Inch, Type to Socket Head
Cap Screw, Size to #10, Fit to Normal and End Condition
to Through All.

Beginner Part 5: Pattern

41

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com

For positions placement for this counterbore hole, click on


Positions tab.
at lower left edge.

Beginner Part 5: Pattern

Click one point

42

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com

11. Click on Smart Dimension


sketched circle as sketch below.

and

and dimension

12. To pattern this counterbore hole, click on CBORE for #10


Socket Head Cap Screw1

and click Linear Pattern.


Direction 1 pattern.

Beginner Part 5: Pattern

Click on bottom edge as

43

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com

Set D1 to 2.5in and pattern # to 3. Click on highlighted


arrow to switch it directions.

13. Click on left edge as Direction 2 pattern.

Set D2 to 3.4in and number of pattern # to 2. You can click

Beginner Part 5: Pattern

44

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com
on arrow to switch it directions.

and

14. Click on top face and click Sketch.

Click on Circle,

Beginner Part 5: Pattern

sketch a circle with center to open hole.

45

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com

Click Smart Dimension,


1.5in.

set circle diameter to

15. Click Line,


sketch a vertical line crossing sketch circle at
12 oclock to 6 oclock.

Press Esc key to end Line. Exit sketch.


16. Click on Hole Wizard,
on Hole Type click on Tap,
Standard: Ansi Inch, Type: Tapped Hole, Hole
Specifications Size:1/4-20, End Condition Through All.

Beginner Part 5: Pattern

46

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com

For positions placement for this tap hole, click on Positions


tab.
oclock last sketched circle.

Beginner Part 5: Pattern

Click one point at 12

47

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com

and

17. To hide guide sketch, click Sketch4 and click Hide.

18. To pattern tap hole, click on 1/4-20 Tapped Hole1

and click Circular Pattern.

Change view to isometric by click on View


Orientation>Isometric

Click on open inner hole face as its pattern axis, set


instances # to 6 and

Beginner Part 5: Pattern

48

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 5: Pattern

www.solidworkstutorials.com

19. Save

the part as Block and youre done! Simple isnt it?

Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com

Beginner Part 5: Pattern

49

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

Beginner Part 6: Assembly Parts


Assembly is a part of design process, it show how all designed
parts work together as a single unit. ...

1.

Click New,

click Part,

OK.

2.

Click Front Plane, insert sketch on plane by click Sketch.

3.

Click on Corner Rectangle,


origin.

In this tutorial you will create this


toy horse by assembly parts to one
unit assembly.

and

4.

5.

Beginner Part 6: Assembly Parts

Click Smart Dimension


sketch below.

and

sketch a rectangle start at

and dimension sketch as

Click Features>Extruded Boss/Base,


set D1 to 4in

on Direction 1

50

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

6.

Beginner Part 6: Assembly Parts

and
.
Click on right face and click Normal To.

51

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com
7.

Click on right face again and click Sketch.

Click on Circle

and sketch 4 circle at each corner. Click

on Smart Dimension
sketched below.

8.

Click on Features>Extruded Cut

Through All
on View OrientationIsometric.

Beginner Part 6: Assembly Parts

and dimension sketch as

and set Direction 1 to

and

. Click

52

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

9.

Click on top face and click Normal To.

Click on top face again and click Sketch.

Beginner Part 6: Assembly Parts

53

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

Click on Corner Rectangle


top and bottom.

Click on Smart Dimension


rectangles as sketched below.

Beginner Part 6: Assembly Parts

and sketch 2 rectangles at

and dimension these

54

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

10. Click on Features>Extruded Cut


1.0in

and set Direction 1 to

and
.
Click on View Orientation>Isometric.

Beginner Part 6: Assembly Parts

55

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

11. Save

the part as Body.

12. Click New,

click Part,

OK.

13. Click Right Plane, insert sketch on plane by click Sketch.

14. Click on Corner Rectangle,


origin.

and

Beginner Part 6: Assembly Parts

sketch a rectangle start at

56

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

15. Click Smart Dimension


sketch below.

and dimension sketch as

16. Click Centerline


and sketch vertical
centerline through top edge midpoint to bottom midpoint.
Press Esc to end centerline.

Beginner Part 6: Assembly Parts

57

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

17. Click on Circle,

sketch 3 circles onto centerline and

using Smart Dimension


sketched below.

dimension sketch as

18. Click Features>Extruded Boss/Base,


set D1 to 0.25in

and

on Direction 1

. Click on View

Orientation>Isometric.

Beginner Part 6: Assembly Parts

58

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

19. To change part color, right click on


Part2>Appearance>Appearance

On Color select Shiny and pick white color.

and
20. Save

the part as Leg.

21. Click New,

Beginner Part 6: Assembly Parts

click Part,

OK.

59

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com
22. Click Right Plane, insert sketch on plane by click Sketch.

23. Click on Circle,

Dimension

and sketch a circle. Click Smart

dimension this circle to 0.25in.

24. Click Features>Extruded Boss/Base,


set D1 to 0.25in

and

on Direction 1

25. Click on right face and click Normal To.

Click on this face again and click Sketch.

Beginner Part 6: Assembly Parts

60

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

26. Click on Circle,

Dimension

and sketch a circle. Click Smart

dimension this circle to 1.5in.

27. Click Features>Extruded Boss/Base,


set D1 to 0.25in

and

on Direction 1

28. To change part color, right click on


Part3>Appearance>Appearance

Beginner Part 6: Assembly Parts

61

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

On Color select Standard and pick red color.

and

29. Save

the part as Wheel.

30. Click New,

click Part,

OK.

31. Click Right Plane, insert sketch on plane by click Sketch.

Beginner Part 6: Assembly Parts

62

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

32. Click on Line,

and sketch a horse head.

33. Click on Smart Dimension


as sketched below.

and dimension sketch

34. Click Features>Extruded Boss/Base,


set D1 to 0.5in

and
35. To change part color, right click on
Part4>Appearance>Appearance

Beginner Part 6: Assembly Parts

on Direction 1

63

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

On Color select Shiny and pick white color.

and

36. Save

the part as Head.

37. Click New,

Beginner Part 6: Assembly Parts

click Part,

OK.

64

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com
38. Click Right Plane, insert sketch on plane by click Sketch.

39. Click on Line,

and sketch a horse tail.

40. Click on Smart Dimension


as sketched below.

Beginner Part 6: Assembly Parts

and dimension sketch

65

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

41. Click Features>Extruded Boss/Base,


set D1 to 0.5in

and
42. To change part color, right click on
Part5>Appearance>Appearance

on Direction 1

On Color select Shiny and pick white color.

Beginner Part 6: Assembly Parts

66

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

and

43. Save

the part as Tail.

Lets begin assembly all this parts.

44. Click New,


click Assembly,
OK.
45. To add part in assembly, Click Browse

Beginner Part 6: Assembly Parts

67

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com
Select Body.sldprt and click Open. Click on workspace.

46. To add leg part, click Insert Components


Browse

Beginner Part 6: Assembly Parts

, click

68

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com
Select Leg.sldprt and click Open. Click on workspace.

47. To add wheel part, click Insert Components


click Browse

Beginner Part 6: Assembly Parts

69

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com
Select Wheel.sldprt and click Open. Click on workspace.

48. Each of this part need to be mate together, click Mate


click on body right face

and turn the assembly around (click wheel button and turn
model) click on leg inner face.

Beginner Part 6: Assembly Parts

70

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

Coincident mate already pre selected, click


49. Turn the assembly back to previous view.

Beginner Part 6: Assembly Parts

71

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com
50. Click on inner hole face on body and inner hole of leg.

The Concentric mate already pre selected, click


this step for bottom hole.

. Repeat

and
.
51. Turn the assembly the other way.

Beginner Part 6: Assembly Parts

72

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com
52. Click on wheel shaft face and inner leg hole.

Concentric mate already pre selected, click


53. Click on inner wheel face

turn the assembly to left side and click on outer leg face.

Coincident mate already pre selected, click


.
54. Repeat step 46 53 for other set of legs and wheels.

55. To add head part, click Insert Components


click Browse

Beginner Part 6: Assembly Parts

73

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

Select Head.sldprt and click Open. Click on workspace. To

add tail part, click Insert Components


Browse

, click

Select Tail.sldprt and click Open. Click on workspace.

Beginner Part 6: Assembly Parts

74

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

56. Click Mate

, click on tail face,

turn assembly the other way, and click on back face cut.

Coincident mate already pre selected, click


57. Click on side face of body cut,

turn assembly to left and click on side face of tail,

Beginner Part 6: Assembly Parts

75

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

Coincident mate already pre selected, click


58. Click on top edge of tail,

turn assembly to view top body and click on top face of the
body.

Coincident mate already pre selected, click


.
59. Turn the model to facing front of the body, click on side face
of inner cut,

Beginner Part 6: Assembly Parts

76

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

turn the assembly to left and click on head side face.

Coincident mate already pre selected, click


60. Click on inner cut face of the body,

turn the assembly around and click on back head face.

Beginner Part 6: Assembly Parts

77

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com

Coincident mate already pre selected, click


.
61. Turn the assembly to view front side, click on head lower
edge,

and click on body bottom inner cut.

Coincident mate already pre selected, click

Beginner Part 6: Assembly Parts

78

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 6: Assembly Parts

www.solidworkstutorials.com
62. Click View Orientation>Isometric

and youre done!

63. Save
isnt it?

the assembly as Horse and youre done! Simple

Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com

Beginner Part 6: Assembly Parts

79

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

Beginner Part 7: Detailing Drawing


Once solid parts created we need to transfer it to engineering
drawing so the others can understand your parts

1.

Click New,

click Drawing,

OK.

2.

On Sheet Format/Size select A Landscape and OK.

3.

Click Browse...

In this tutorial you create drawing


for this part.

locate you Block.sldprt (Part from Beginner Part 5: Pattern


tutorials)

Beginner Part 7: Detailing Drawing

70

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

4.

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

Click Open.
For Orientation select Top and for Display Style select
Hidden Lines Visible,

71

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing


5.

www.solidworkstutorials.com
Click on sheet to add this view,

click again on left side to add side view of the part,

click once more to upper right of sheet to view its 3D view.

Beginner Part 7: Detailing Drawing

72

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

6.

7.

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

Click
.
Repositions part 3D view to upper right corner of the sheet
by dragging it to this location.

There is no centerline for holes in side view, lets add this


centerline, click on side view,

73

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

Click on Annotation tab,

click on Centerline,

centerline automatically added to side view, click

8.

Beginner Part 7: Detailing Drawing

Click Smart Dimension


and pull dimension to bottom.

and click on bottom edge

74

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

9.

www.solidworkstutorials.com

Zoom in, click on center hole edge,

click on counter bore hole edge

and pull dimension to bottom side.

Beginner Part 7: Detailing Drawing

75

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

10. Click on center hole edge,

click on counter bore hole edge

Beginner Part 7: Detailing Drawing

76

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

and pull dimension to bottom side.

11. Repeat step 10 and continue dimension for the third counter
bore hole.

Beginner Part 7: Detailing Drawing

77

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

Beginner Part 7: Detailing Drawing

78

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

12. Click on center hole edge,

click on left edge

and pull dimension to bottom side.

Beginner Part 7: Detailing Drawing

79

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

13. Repeat step 12 for right edge.

Beginner Part 7: Detailing Drawing

80

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

14. Click on center hole edge and pull out its diameter
dimension.

Beginner Part 7: Detailing Drawing

81

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

15. Click on thread diameter and pull out its radius dimension.

Beginner Part 7: Detailing Drawing

82

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

16. Click on center hole edge,

click on counterbore hole edge

and pull its dimension to left side.

Beginner Part 7: Detailing Drawing

83

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

17. Click on center hole edge,

click on bottom edge

and pull its dimension to left side.

Beginner Part 7: Detailing Drawing

84

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

18. Repeat steps 16 and 17 for top counterbore and top edge.

19. Click

to end Smart Dimension. Click on Annotation tab,

click on Hole Callout.

Click on counterbore hole

and pull out its hole callout to right side.

Beginner Part 7: Detailing Drawing

85

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

20. Click on thread

and pull out its hole callout to right side.

Click

Beginner Part 7: Detailing Drawing

to end hole callout annotation.

86

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

21. Click on Sketch tab,

Click on Centerline,
sketch a
centerline thru center of Block. Point (hover your cursor) to
midpoint of left edge (dont click),

move you cursor to left side,

now click on sheet and click again on right side.

Press Esc to end centerline.

Beginner Part 7: Detailing Drawing

87

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

22. Click on centerline,

click on View Layout tab,

click on Section View,


check Flip Direction

on section Line option,

and click on sheet for this section view.

Beginner Part 7: Detailing Drawing

88

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

23. You can customize each view how its appear on drawing by
changing its display style. Click on Section A-A view,

on Display Style click on Hidden Line Removed.

Click

Beginner Part 7: Detailing Drawing

. Your section view now changed.

89

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

24. Click on 3D view,

on Display Style click on Shaded With Edges.

To change its scale, under Scale click on Use custom scale,


set to 1:3

and

Beginner Part 7: Detailing Drawing

90

Buyer: Olga Simiacov (olga.simiacov@ratb.ro)


Transaction ID: 1V0226867H4668431

Beginner Part 7: Detailing Drawing

www.solidworkstutorials.com

25. Save
it?

the drawing as Block and youre done! Simple isnt

Go to table of contents
Go to beginning of chapter tutorial
Go to www.solidworkstutorials.com

Beginner Part 7: Detailing Drawing

91

Das könnte Ihnen auch gefallen