Beruflich Dokumente
Kultur Dokumente
Document ID
Annexure (ES0122-75650500-MOT-0001)
Revision: 00
Item Code
MOT001
Qty: As below
Description
Sheet : 1 of 4
Item code
Item Description
Element
Total Qty.
1.
Make
2.
Altitude referring
3.
Location
4.
Environment
5.
Application
To be mentioned by Vendor
6.
Rating in KW at starting
method as per clause no.18
To be mentioned by vendor
7.
Speed in RPM
To be mentioned by vendor
8.
Frame size
To be mentioned by vendor
9.
Voltage % / frequency % /
Combined variation %
460 V 10% / 60 Hz 5%
/10 % (Solidly earthed)
10.
11.
Insulation class
12.
13.
Duty
14.
Type
15.
Type of mounting
16.
Degree of Protection
17.
Type of enclosure
TEFC
18.
Starting Method
19.
Starting Current
700 %
20.
Method of coupling
To be mentioned by vendor
21.
Direction of rotation
Bi directional
22.
23.
Anti-condensation heater
Supply Voltage : 230 V, 1
Phase, 60Hz
PTC/RTDs (2 Nos. per phase)
45 C & Class B
70C by resistance & 80C by RTD method
Continuous (S1) / Based on equipment
application
3 Phase, Induction Motor SQ Cage
Horizontal foot mounting (B3) / Based on
equipment application
IP 55 (GI sheet fabricated Canopy to be
supplied for all outdoor duty motors)
APPROVED By : EAM
Annexure (ES0122-75650500-MOT-0001)
Revision: 00
Item Code
MOT001
Qty: As below
Description
Sheet : 2 of 4
24.
Terminal Box
i)
Location
ii)
Angle of rotation
iii)
No. of terminals
iv)
External power cable
size(XLPE insulation)
v)
Cable gland type/size
vi)
Fault level
:
:
:
:
:
:
25.
26.
27.
28.
29.
80%
:
:
:
1
2
3
APPROVED By : EAM
Annexure (ES0122-75650500-MOT-0001)
Revision: 00
Item Code
MOT001
Qty: As below
Description
Sheet : 3 of 4
iii)
30.
31.
32.
33.
34.
35.
36.
37.
38.
Equally spread
Paint shade
:
:
RAL 7032
Starting torque shall be not less than 200 % of rated torque unless otherwise
specified.
Motor shall be capable of withstanding locked rotor current for at least 5 seconds
longer than the starting time under rated load conditions.
Motors shall be suitable to withstand at 150% of rated voltage even at phase
opposition.
Motors shall work satisfactorily at Full Load for 5 minute under 75% voltage
condition.
Hot withstand time of the motor shall be at least 10 seconds longer than the starting
time under rated load conditions, for the motors where the starting time is more
than 30 second. For motors with lesser starting time, a margin of 5 seconds shall be
ensured.
Motor shall be designed to withstand hundred twenty (120) percent of rated speed
without any mechanical damage for two minutes,
The maximum double amplitude vibrations for motors shall be as per IEC IEC-34
(Latest)
Maximum noise level measured at a distance of 1 meter from the outer surface of
the motor shall not exceed 85 db (A).
39.
All Motors shall be energy efficient type (IE2) as per IEC: 60034-30.
40.
41.
42.
43.
44.
45.
Break away torque, pull up torque and pull out torque shall be properly coordinated
with the speed torque characteristics of the driven equipment.
Supplier shall be fully responsible for determining motor duty cycle, rating
performance, tests and mechanical arrangement entirely adequate for the duty and
comply with the relevant standards for the applications in the factory, environment
and site conditions.
All VFD driven Motors winding should be VPI TREATED with two coats enameled.
The motor shall be designed to operate both DOL/VFD continuously.
VFD driven Motors rating shall have Insulated Bearing at NDE.
APPROVED By : EAM
Annexure (ES0122-75650500-MOT-0001)
Revision: 00
Item Code
MOT001
Qty: As below
Description
Sheet : 4 of 4
46.
47.
VFD driven motors shall be suitable to run on IGBT Based Drives and hence to
be sized to operate satisfactorily under Lowest Speed condition with out
effecting the cooling of motors. Motor speed variation range shall be 30 % to
100 %.
Manufacturer shall submit detailed calculations for adequacy of the motor design
under extreme conditions furnishing motor selection chart for VFD application.
Motor shall be routine tested as per applicable standard by supplier and results to be
furnished to ISGEC. On review of the same motor may be inspected at
manufacturers works by ISGEC.
For TYPE/ROUTINE test by us or our ultimate client. Dispatch clearance shall be
given by us after reviewing the test certificates OR inspection.
All the motors shall be manufactured and tested as per IEC standard only.
Test certificates shall be based on IEC only will be acceptable.
48.
The consumables / often replaced / changed items used in the motors like
lubricants, bearings, coolants, etc., shall be of universally available make
and model. Supplier to confirm this and specify in the motor data sheet.
49.
One set of Motor bearings at drive end and non-drive end per type / rating
of motor shall be supplied along with motor as operational spare.
50.
GI sheet fabricated canopy (Hood) for each motor located in outdoor and
exposed to direct atmosphere application shall be included in the vendor
scope. This is not required for indoor duty type motors.
51.
52.
APPROVED By : EAM