Beruflich Dokumente
Kultur Dokumente
Whereas the Parliament of India has set out to provide a practical regime of right to
information for citizens to secure access to information under the control of public authorities,
in order to promote transparency and accountability in the working of every public authority,
and whereas the attached publication of the Bureau of Indian Standards is of particular interest
to the public, particularly disadvantaged communities and those engaged in the pursuit of
education and knowledge, the attached public safety standard is made available to promote the
timely dissemination of this information in an accurate manner to the public.
1 +, 1 +
01 ' 5
Jawaharlal Nehru
! $ ' +-
Satyanarayan Gangaram Pitroda
! > 0 B
BharthariNtiatakam
Price Group 2
Grade
Nominal
Thickness
mm
Minimum
Minimum
Maximum
Maximum Specific
Stacking
Polarization
Specific Core
Core Loss (W/kg)
Factor
in Tesla at a
Loss (W/kg)
Polarization
Field Strength
Polarization
at 1.7 T and
of 800 A/m
at 1.5 T and
50 Hz
50 Hz
(1)
(2)
(3)
(4)
(5)
(6)
23CG110
0.23
0.73
1.10
1.78
0.945
23CG120
0.23
0.77
1.20
1.78
0.945
23CG127
0.23
0.80
1.27
1.75
0.945
27CG120
0.27
0.80
1.20
1.78
0.950
27CG130
0.27
0.85
1.30
1.78
0.950
27CG140
0.27
0.89
1.40
1.75
0.950
30CG130
0.30
0.85
1.30
1.78
0.955
30CG140
0.30
0.92
1.40
1.78
0.955
30CG150
0.30
0.97
1.50
1.75
0.955
35CG145
0.35
1.03
1.45
1.78
0.960
35CG155
0.35
1.07
1.55
1.78
0.960
35CG165
0.35
1.11
1.65
1.75
0.960
NOTES
1 The above samples are sheared longitudinal to the rolling direction and then stress relief annealed in a neutral or reducing
atmosphere to develop magnetic property at 780C to 820C.
2 The values of Maximum Specific Core Loss (W/kg) at 1.5 T are for information only.
Nominal
Thickness
mm
Maximum Specific
Core Loss (W/kg)
Polarization
at 1.7 T and 50 Hz
Minimum
Polarization
in Tesla at a
Field Strength
of 800 A/m
Minimum
Stacking
Factor
(1)
(2)
(3)
(4)
(5)
23HP85 d
0.23
0.85
1.85
0.945
23HP90 d
0.23
0.90
1.85
0.945
27HP90 d
0.27
0.90
1.85
0.950
27HP95 d
0.27
0.95
1.85
0.950
27HP100
0.27
1.00
1.88
0.950
27HP110
0.27
1.10
1.88
0.950
30HP105
0.30
1.05
1.88
0.955
30HP110
0.30
1.10
1.88
0.955
35HP115
0.35
1.15
1.88
0.960
35HP125
0.35
1.25
1.88
0.960
35HP135
0.35
1.35
1.88
0.960
NOTES
1 d This grade may be delivered in domain refined condition. The magnetic properties of some domain refined material may
deteriorate when the material is subjected to heat treatment.
2 The domain refined grades need to be checked by single sheet method as in clause 14.3.
NOTE Based on 610 to 910 mm width of material. For widths less than 610 mm the number of permissible fractures should
be reduced in proportion to the ratio of the width to 610 mm.
10.2.2 This alternate ductility test method is as described in IS 649 (Section 8, clauses 49 and 50).
The minimum number of bends is one. The value applies to the parallel to the direction of rolling.
(Page 5, clause 11.2) Insert the following at the end:
, for widths up to and including 1 000 mm. For materials supplied with as rolled edges and/or widths
above 1 000 mm the tolerances on nominal width should be the subject of agreement while ordering.
(Page 6, Table 5) Substitute the following for the existing table
Nominal Width, l, mm
(1)
(2)
(3)
i)
l 150
+ 0.2
0.0
ii)
+ 0.3
0 .0
iii)
+ 0.5
0 .0
iv)
+ 1.0
0 .0
v)
l >1 000
+ 1.5
0 .0
Tolerances
NOTE As per agreement, width Tolerance can be ve or +ve or both ve and +ve subject to tolerance band as given in above table.
(Page 6, clause 14) Insert the following as new subclauses at the end:
14.3 In the case where the measurement of magnetic polarization and specific core loss shall be made
using single sheet method as specified in IS 649, the test specimen for the single sheet tester shall consist of
one sheet having the following dimensions:
-
All the test specimens shall be cut parallel to the direction of rolling. The permitted tolerance for the angle
between the direction of rolling and the direction of cutting is 1 degree.
14.4 In case of measurements of specific core loss on aged test pieces, these shall be aged by heating at
2250C 50C for duration of 24 hours and shall be cooled to ambient temperature.
(MTD 4)
Reprography Unit, BIS, New Delhi, India
Grade
Nominal
Thickness
mm
Maximum Specific
Core Loss (W/kg)
Polarization
at 1.5 T
Maximum Specific
Core Loss (W/kg)
Polarization
at 1.7 T
50 Hz
60 Hz
50 Hz
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
23CG110
0.23
0.73
0.96
1.10
1.45
1.78
0.945
23CG120
0.23
0.77
1.01
1.20
1.57
1.78
0.945
23CG127
0.23
0.80
1.03
1.27
1.65
1.75
0.945
27CG120
0.27
0.80
1.07
1.20
1.58
1.78
0.950
27CG130
0.27
0.85
1.12
1.30
1.68
1.78
0.950
27CG140
0.27
0.89
1.15
1.40
1.75
1.75
0.950
30CG130
0.30
0.85
1.15
1.30
1.71
1.78
0.955
30CG140
0.30
0.92
1.21
1.40
1.83
1.78
0.955
30CG150
0.30
0.97
1.25
1.50
1.90
1.75
0.955
35CG145
0.35
1.03
1.36
1.45
1.91
1.78
0.960
35CG155
0.35
1.07
1.45
1.55
2.04
1.78
0.960
35CG165
0.35
1.11
1.52
1.65
2.12
1.75
0.960
60 Hz
Minimum
Minimum
Polarization Stacking
in Tesla at a
Factor
Field Strength
of 800 A/m
Grade
Minimum
Polarization
Maximum Specific Core
Nominal Loss (W/kg) Polarization in Tesla at a
Thickness
at 1.7 T
Field Strength
mm
of 800 A/m
Minimum
Stacking
Factor
50 Hz
60 Hz
(5)
(6)
23HP85 d
0.23
0.85
1.12
1.85
0.945
23HP90 d
0.23
0.90
1.19
1.85
0.945
23HP95 d
0.23
0.95
1.25
1.85
0.945
23HP100 d
0.23
1.00
1.32
1.85
0.945
27HP90 d
0.27
0.90
1.19
1.85
0.950
27HP95 d
0.27
0.95
1.25
1.85
0.950
27HP100
0.27
1.00
1.32
1.88
0.950
27HP110
0.27
1.10
1.45
1.88
0.950
30HP105
0.30
1.05
1.38
1.88
0.955
30HP110
0.30
1.10
1.46
1.88
0.955
30HP120
0.30
1.20
1.58
1.88
0.955
35HP115
0.35
1.15
1.51
1.88
0.960
35HP125
0.35
1.25
1.64
1.88
0.960
35HP135
0.35
1.35
1.77
1.88
0.960
NOTES
1 d This grade may be delivered in domain refined condition . The magnetic properties of some
domain refined material may get deteriorate when material is subjected to heat treatment.
2 In cases where material gets deteriorated when subjected to heat treatment The domain refined
grades need to be checked by Single sheet method as given in 14.3. For other grades/other type
of domain refined grades which do not deteriorate when subjected to heat treatment, the test
method remains as per EPSTEIN method as given in IS 649.
3 The values of Maximum Specific Core loss (W/kg) at 60 Hz are for information only.
(MTD 4)
4