Beruflich Dokumente
Kultur Dokumente
A flange is a forged or cast ring of steel designed to connect sections of pipe or join pipe to
a pressure Vessel, pump or any other integral flanges assembly.
Flanges are joined to each other by bolting and joined to the piping system by welding or threading.
The basic types of flanges are; Slip on, Blind, Weld Neck, Threaded, Socket Weld, Lap Joint and
Orifice.
Flanges are designed to the following pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and
2500lb.
The most common facings machined on flanges are:
(a) Raised face, 1/16 inch for 150lb and 300lb, inch for 400lb and heavier.
(b) Flat face, for 150lb and 300lb only, other may be flat face on request.
(c) Ring type joint, may be applied to all pressure ratings.
TYPES & APPLICATIONS
Slip-On Flange
The flange is slipped over the pipe and then welded both inside and outside to provide sufficient
Strength and prevent leakage. This flange is used in preference to weld necks by many users
because of its lower cost and the fact that less accuracy is required when cutting pipe to length.
Blind Flanges
This is a flange without a bore and is used to shut off a piping system or vessel opening. It also
permits Easy access to vessels or piping systems for inspection purposes. Blind flange can be
supplied with or without hubs at the manufacturers option.
Weld-Neck flange
This is designed to be joined to a piping system by buttwelding. It is relatively expensive because of
Its long neck, but is preferred for high stress applications. The neck, or hub transmits stresses to the
the base of the hub to the wall thickness at the butt weld, provide important reinforcement of the
flange. The bore of the flange matches the bore of the pipe, reducing turbulence and erosion.
Threaded Flange
This is similar to a slip-on flange in outline, but the bore is threaded, thus enabling assembly without
welding. This obviously limits its application to relatively low pressure piping systems. The flange
may be welded around the joint after assembly, but this is not considered a satisfactory method of
increasing its applications.
General flange faces such as the RTJ, T&G and the F&M shall never be bolted together. The reason
for this is that the contact surfaces do not match and there is no gasket that has one type on one
side and another type on the other side.
Long Neck Flanges
Owing to our rich industrial experience, we are offering a comprehensive range of Long Weld Neck
Flanges. The professionals of our organization source these neck flanges from trusted vendors.
These flanges are unique due to their simple connectivity with other pipes. Moreover, our products
are extensively used in refining industries for linking purposes. Our esteemed patrons can avail these
qualitative range of flanges from us at industry-leading prices.
Flat Face Flanges
The Flat Face (FF) flange has a gasket surface in the same plane as the bolting circle face.
Applications using flat face flanges are frequently those in which the mating flange or flanged fitting
is made from a casting.
Flat face flanges are never to be bolted to a raised face flange. ASME B31.1 says that when
connecting flat face cast iron flanges to carbon steel flanges, the raised face on the carbon steel
flange must be removed, and that a full face gasket is required. This is to keep the thin, bittle cast
iron flange from being sprung into the gap caused by the raised face of the carbon steel flange.
Raised Face Flanges
The Raised Face (RF) type is the most applied flange face, and is easily to identify. It is referred to
as a raised face because the gasket surfaces are raised above the bolting circle face.
Specifications covering the manufacture and dimensions of flanges:
ASTM SPECIFICATIONS
ASTM specifications regulate approved raw materials for which flanges can be made and
specifications .
For stainless flanges are:
ASTM A.182 - Forged or Rolled Alloy Steel Pipe Flanges & Fittings for high temperature service.
ANSI AND MSS SPECIFICATIONS
The standards govern the dimensions and tolerances to which fitting are manufactured:
ANSI B. 16.5
- Steel Pipe Flanges and Flanged Fittings ( inch to 24 inch nominal
diameter)
MSS SP.6
- Flange Facings
MSS SP.25
- Marking of flanges
MSS SP.39
- Bolts and Nuts for Flanges
MSS SP.44
- Large Diameter Pipeline Flanges. (Over 24 inch dia)
API-605
- Large Diameter Flanges for petroleum Usage. (Over 24 inch dia)
The ASME Code is not a standard as such but section VIII provides the procedure for calculating
dimensions
For all pressurised vessels flanges.
The following are not flange specifications but they influence the manufacture of forged steel flange
ANSI B. 31.10
- Code for Pressure Piping
ANSI B. 31.3
- Petroleum Refinery Piping
ANSI B. 31.4
- Oil Transportation Piping
ANSI B. 31.5
- Refrigeration Piping Systems
ANSI B. 31.7
- Nuclear Power Piping
ANSI B. 31.8
- Gas Transmission and Distribution Piping systems
ANSI B. 36.10
- Standard for Wrought Steel pipe
ANSI B. 36.19
- Standard for Stainless Steel Pipe
ANSI B. 16.10
- Valve Dimensions Face & End
ANSI B. 16.11
- Forged Fittings Socket Weld & Threaded
Blind Flanges
Flanges
Orifice Flanges
Raised Flanges
Slip-On Flanges
Thread Flanges
Weld-Neck Flanges