Beruflich Dokumente
Kultur Dokumente
1.
INTRODUCTION
Nanotechnology is the science of particles under the size of 100 nm that has become a great
field of interest for many researchers in the past few years. Incredible development in
nanotechnology has paved ways for fundamentals in nano-biotechnology [1], quantum dots
[2], applied microbiology and many more fields. In recent years nanotechnology has made
its mark in various fields such as targeted drug delivery, chemical industry, cosmetology
and nano medicine.
Nanoparticles are found to have extremely small size reduced properties and high surface
to volume ratio that leads to both physical and chemical differences in their properties as
compared to macro particles with the same chemical configuration [3] [4] [5] [11]. These
particles also have many applications in different fields such as medical imaging,
nanocomposites, filters, drug delivery, and hyperthermia of tumors. [6] [7] [8] [9]. Though
nanoparticles are being produced by physical, chemical and biological methodology for
quite some time, researches are still trying to find out many new and interesting ways to
synthesis nanoparticles for varied particle application (Fig 1).
P age |2
The ball milling system consists of a turn disc and two or four vials. The rotation of the
turn disc is in one direction while that of the vials are in the opposite direction. Thus due
to the rotation of the turn table and the vial in opposite direction to each other, a centrifuga l
force is generated that are alternatively synchronized (Fig 2).
P age |3
TiO 2 is an extremely novel photo catalyst that can be used for the photo-degradation of
natural ecological contaminations [13] [14]. The photo generated electron-hole pair is a
very important characteristic of TiO 2 as it is responsible for the initiation of a number of
reactions which eventually decompose the toxic organic molecules and thus reduce the
environmental contaminants [15] [16].
Just like TiO2 , ZnO is another interesting photo catalyst which has drawn many interest of
many researchers. ZnO also has various unique optical and electrical properties same as
TiO 2 [17] [18] [19]. ZnO nano particles these days are being researched in conducting
films, solar cells, cosmetology, photo catalysis and UV lasers [20]. But one of the most
important application of ZnO nano particles has been exploited as photo catalyst in the
treatment of environmental pollution especially in the field of water treatment [21] [22].
The application of both TiO 2 and ZnO as photo catalyst has been made possible only due
to the feature of wide band gap of both materials [23].
In this paper, an effort has been made to synthesize TiO 2 ZnO nanocomposites with the
help of physical method of ball milling for different percentage concentration and for
different milling time. The synthesized nanocomposites would be then characterized using
the X-Ray Diffraction Method.
2.
EXPERIMENTAL
2.1
SAMPLE PREPARATION
To prepare the sample for synthesis of nanoparticle through ball milling firstly 2.400 grams
of TiO 2 and 0.612 grams of ZnO were weighed to get 80-20% of TiO 2 ZnO composite
and also 1.500 grams of TiO 2 and 1.529 grams of ZnO were weighed to get a 50-50% of
TiO 2 ZnO composite and were put into two different vials respectively that were made
up of stainless steel with a capacity of 10 mL each. The vials also contained six stainless
steel balls and the diameter of each ball was 10 mm each. The vials were then put in the
SPEX 8000M Miller Mix of which the turn table rotation speed was 500 RPM and the BPR
was 21:3. The milling time varied from 1 to 9 hours at room temperature. After every 0.5
P age |4
hours, 1 hour, 3 hours and 9 hours, 0.5 grams of the each 80-20% and 50-50% of TiO 2
ZnO sample were collected for further analysis.
TiO 2
ZnO
TiO 2
ZnO
TiO 2
ZnO
(mol%)
(mol%)
(mol)
(mol)
(g)
(g)
80
20
0.03005
0.00751
2.400
0.612
50
50
0.01878
0.01878
1.500
1.529
P age |5
3.
Fig 4 shows the XRD peak obtained for 80-20% of TiO 2 ZnO nanocomposite that was
synthesized after a ball milling process of 0.5 hours. The obtained XRD peaks indicate that
the particles synthesized are in the nano meter range. From this XRD pattern we can
identify the different phases of TiO 2 ZnO composite nanoparticles such as Rutile (R),
Zincite (Z) and Anatase (A). The peaks obtained were at 17 (2,2,0), 10 (1,0,0) and 12
(2,1,2) respectively for the three obtained phases. The ration of R: Z: A obtained in this
synthesized sample was found to be 1.22:12.5:86.
Fig 4: XRD of 80-20% TiO 2 ZnO composite synthesized sample after 0.5 hours of ball
milling
Fig 5 shows the XRD peak obtained for 80-20% of TiO 2 ZnO nanocomposite that was
synthesized after a ball milling process of 1 hour. The obtained XRD peaks indicate that
the particles synthesized are in the nano meter range. From this XRD pattern we can
identify the different phases of TiO 2 ZnO composite nanoparticles such as Rutile (R),
Zincite (Z) and Anatase (A). The peaks obtained were at 26 (3,0,1), 7.9 (2,2,2) and 66
(1,0,1) respectively for the three obtained phases. The ration of R: Z: A obtained in this
synthesized sample was found to be 4:13:5.
P age |6
Fig 5: XRD of 80-20% TiO 2 ZnO composite synthesized sample after 1 hour of ball
milling
Fig 6 shows the XRD peak obtained for 80-20% of TiO 2 ZnO nanocomposite that was
synthesized after a ball milling process of 3 hours. The obtained XRD peaks indicate that
the particles synthesized are in the nano meter range. From this XRD pattern we can
identify the different phases of TiO 2 ZnO composite nanoparticles such as Rutile (R),
Zincite (Z) and Anatase (A). The peaks obtained were at 33 (1,1,1), 30 (0,2,1) and 28
(0,1,3) respectively for the three obtained phases. The ration of R: Z: A obtained in this
synthesized sample was found to be 43:46:20.2.
Fig 6: XRD of 80-20% TiO 2 ZnO composite synthesized sample after 3 hours of ball
milling
P age |7
Fig 7 shows the XRD peak obtained for 80-20% of TiO 2 ZnO nanocomposite that was
synthesized after a ball milling process of 9 hours. The obtained XRD peaks indicate that
the particles synthesized are in the nano meter range. From this XRD pattern we can
identify the different phases of TiO 2 ZnO composite nanoparticles such as Rutile (R),
Zincite (Z) and Anatase (A). The peaks obtained were at 49 (1,1,6), 50 (0,2,1) and 48
(0,0,4) respectively for the three obtained phases. The ration of R: Z: A obtained in this
synthesized sample was found to be 18:62:20.
Fig 7: XRD of 80-20% TiO 2 ZnO composite synthesized sample after 9 hours of ball
milling
Fig 8 shows the XRD peak obtained for 50-50% of TiO 2 ZnO nanocomposite that was
synthesized after a ball milling process of 0.5 hours. The obtained XRD peaks indicate that
the particles synthesized are in the nano meter range. From this XRD pattern we can
identify the different phases of TiO 2 ZnO composite nanoparticles such as Rutile (R),
Zincite (Z) and Anatase (A). The peaks obtained were at 10 (0,2,4), 11 (0,1,0) and 8
(1,1,2) respectively for the three obtained phases. The ration of R: Z: A obtained in this
synthesized sample was found to be 0.4:44:54.
P age |8
Fig 8: XRD of 50-50% TiO 2 ZnO composite synthesized sample after 0.5 hours of ball
milling
Fig 9 shows the XRD peak obtained for 50-50% of TiO 2 ZnO nanocomposite that was
synthesized after a ball milling process of 1 hour. The obtained XRD peaks indicate that
the particles synthesized are in the nano meter range. From this XRD pattern we can
identify the different phases of TiO 2 ZnO composite nanoparticles such as Rutile (R),
Zincite (Z) and Anatase (A). The peaks obtained were at 13 (0,0,2), 8 (1,1,0) and 9
(1,0,5) respectively for the three obtained phases. The ration of R: Z: A obtained in this
synthesized sample was found to be 17:30:29.
Fig 9: XRD of 50-50% TiO 2 ZnO composite synthesized sample after 1 hour of ball
milling
P age |9
Fig 10 shows the XRD peak obtained for 50-50% of TiO 2 ZnO nanocomposite that was
synthesized after a ball milling process of 3 hours. The obtained XRD peaks indicate that
the particles synthesized are in the nano meter range. From this XRD pattern we can
identify the different phases of TiO 2 ZnO composite nanoparticles such as Rutile (R),
Zincite (Z) and Anatase (A). The peaks obtained were at 5 (3,1,1), 8 (0,2,0) and 4 (1,3,2)
respectively for the three obtained phases. The ration of R: Z: A obtained in this synthesized
sample was found to be 3.5:18:3.
Fig 10: XRD of 50-50% TiO2 ZnO composite synthesized sample after 3 hours of ball
milling
Fig 11 shows the XRD peak obtained for 50-50% of TiO 2 ZnO nanocomposite that was
synthesized after a ball milling process of 9 hours. The obtained XRD peaks indicate that
the particles synthesized are in the nano meter range. From this XRD pattern we can
identify the different phases of TiO 2 ZnO composite nanoparticles such as Rutile (R),
Zincite (Z) and Anatase (A). The peaks obtained were at 13 (1,0,1), 3 (1,1,2) and 8
(0,3,1) respectively for the three obtained phases. The ration of R: Z: A obtained in this
synthesized sample was found to be 14.9:0.68:0.71.
P a g e | 10
Fig 11: XRD of 50-50% TiO2 ZnO composite synthesized sample after 9 hours of ball
milling
4.
CONCLUSION
In this report, TiO 2 ZnO nanocomposite has been successfully synthesized using the
physical technique of ball milling with percentage concentration of TiO 2 and ZnO to be
80-20% and 50-50% respectively under the milling time 0.5 hours, 1 hour, 3 hours and 9
hours. The synthesized eight samples were then characterized using the XRD technique.
The results of XRD indicated that the sample synthesized were in the nano dimension. Also
the peaks were obtained for the phases such as Rutile, Zincite and Anatase which had a
tetrahedral, cubic and tetrahedral shape respectively.
P a g e | 11
REFERENCES
[1]
[2]
[3]
[4]
[5]
[6]
[7]
H. Y. Lee, Z. Li, K. Chen, A. R. Hsu, C. Xu, J. Xie, S. Sun and X. Chen, J. Nucl.
Med., 2008, 49, 13711379.
[8]
[9]
[10]
[11]
[12]
[13]
[14]
[15]
[16]
[17]
H. Lin, L. Li, M. Zhao, X. Huang, X. Chen, G. Li, and R. Yu, J. Am. Chem. Soc.
134, 8328 (2012).
[18]
M. Zhao, L. Li, H. Lin, L. Yang, and G. Li, Chem. Commun. 49, 7046 (2013).
[19]
M. Guo, L. Li, H. Lin, Y. Zuo, X. Huang, and G. Li, Chem. Commun. 49, 11752
(2013).
P a g e | 12
[20]
[21]
[22]
Y. Zhou, W. B. Wu, Ghu, H. T. Wu, and S. G. Cui, Mat. Res. Bull. 43, 2113
(2008).
[23]