Beruflich Dokumente
Kultur Dokumente
for Mac/PC
USER MANUAL
Contents
Table of Contents
Contents2
English3
iRig Keys 37 Pro3
Feautures3
Overview4
Register your iRig Keys 37 Pro4
Installing SampleTank 3 SE4
Installation and setup5
Mac or Windows based computers5
Playing with iRig KEYS 37 PRO5
Octave Shift 6 5
Volume/Data Knob 3 6
Pitch Bend 8 6
Modulation Wheel 9 6
Pedal 2 7
Prog 7 7
EDIT mode7
Set the MIDI Transmit Channel8
Set different velocity (touch) response8
Assign a specific MIDI Control Change number to the VOL/DATA knob9
Send specific MIDI Program Changes numbers, and set Current Program number9
Send All Notes Off MIDI message10
Transpose the keyboard in semitones10
Reset iRig KEYS 37 PRO11
SETs11
How to load a SET11
How to program a SET 11
How to save a SET11
Troubleshooting12
Warranty12
Support and more info12
Regulatory13
English
iRig Keys 37 Pro
Thank you for purchasing iRig KEYS 37 PRO.
Your package contains:
Feautures
Modulation Wheel.
Edit mode.
USB powered.
English
Overview
2
C2
C4
C3
C5
1. Micro-USB port
2. Pedal input
3. Volume/Data knob
4. ON LED
5. Set button
6. Octave buttons
7. Program buttons
8. Pitch wheel
9. Modulation wheel
Installing SampleTank 3 SE
After registering iRig Keys 37 Pro serial number, a download link and serial number of SampleTank 3 SE for
Mac/PC is added to your User Area. Please download it at User Area and authorize it with Authorization
Manager.
User Area
www.ikmultimedia.com/userarea
Authorization Manager
www.ikmultimedia.com/am
4
English
Installation and setup
Mac or Windows based computers
1. Connect the included Micro USB cable to the Micro USB port on iRig KEYS 37 PRO 1 .
2. Connect the USB plug to a free USB socket on your computer.
3. The ON LED 4 will light up. You are now ready to play virtual instruments installed on your computer from
iRig KEYS 37 PRO.
4. Depending on the software you use, you might need to select iRig KEYS 37 PRO from the available MIDI
IN devices.
Octave Shift
By default, iRig KEYS 37 PRO plays notes between C2 and C5. If you need to play notes lower or higher than
this range, you can shift the whole keyboard in octaves using the OCT up and down buttons 6 .
When the LEDs for both OCT buttons are off, no octave shift is applied. You can shift a maximum of 3 octaves
up or 4 octaves down. OCT up or down buttons will illuminate when an octave shift is active.
The OCT up or down buttons will flash each time you press them.
The number of times they flash corresponds to the number of octaves up or down the keyboard is shifted.
5
English
Volume/Data Knob
This knob controls MIDI Volume (CC#07) on iRig KEYS 37 PRO by default, so you can use this to control the
volume of the instrument you are playing.
This control is assignable, so it is also possible to send any other MIDI control change (CC) message.
See the chapter EDIT mode for more information.
Pitch Bend
Move this wheel up or down to send Pitch Bend messages. The wheel has a central rest position.
Moving the wheel up will increase the pitch; moving it down will decrease the pitch.
Note that the amount of pitch change depends on how the receiving virtual instrument is set.
Modulation Wheel
Move this wheel to send Modulation Wheel messages (MIDI CC#01). The lowest position sends a value of 0; the
highest position sends a value of 127.
6
English
Most instruments use this message to control the amount of vibrato or tremolo in the sound, but note that
this depends solely on how the receiving instrument itself is programmed and not on the iRig KEYS 37 PRO
settings.
Pedal
iRig KEYS 37 PRO supports both Sustain Pedals and Expression Pedals. Connect a NORMALLY OPEN sustain
pedal to the jack 2 BEFORE connecting iRig KEYS 37 PRO to the computer. When the pedal is depressed, you
will sustain all keyed notes until the pedal is released. iRig KEYS 37 PRO sends MIDI CC#64 with a value of 127
when the pedal is depressed and a value of 0 when released.
Connect a continuous expression pedal to the jack 2 BEFORE connecting iRig KEYS 37 PRO to the computer
to control EXPRESSION on the sounds youre playing. iRig KEYS 37 PRO sends MIDI CC#11 when the
expression pedal is moved.
Prog
Sound modules like virtual instrument apps or plug-ins can switch sounds when they receive the Program
Change MIDI message. iRig KEYS 37 PRO sends Program Changes by pressing the PROG 7 up or down
buttons.
Starting with the currently selected program, iRig KEYS 37 PRO will send the next higher program numbers
when you press PROG UP and lower program numbers when you press PROG DOWN. To set the current
program see the chapter, EDIT mode.
EDIT mode
iRig KEYS 37 PRO allows you to customize most of its parameters to match any kind of need.
In EDIT mode you can:
Send specific MIDI Program Change numbers and set the current program number.
English
You can exit EDIT mode at any time by pressing the C2 key marked CANCEL/NO.
Please refer to the user manual of the control app for detailed information on this. From the app youll also be
able to select which MIDI messages the external pedals will send.
MIDI instruments can respond to 16 different MIDI channels. For iRig KEYS 37 PRO to play an instrument, you
need the iRig KEYS 37 PRO MIDI Transmit Channel to match the receiving channel of your instrument.
To set the MIDI Transmit Channel:
Press the D#2 key (MIDI CH). Both OCT buttons will flash.
Enter the MIDI Channel number you need using the C3-E4 white keys marked from 0 to 9. Valid numbers
are from 1 to 16, so when needed, you can enter two digits consecutively.
Press the C5 key (ENTER/YES) to confirm your input. Both PROG buttons will flash to show the setting has
been accepted, and iRig KEYS 37 PRO will automatically exit EDIT mode.
The keyboard on iRig KEYS 37 PRO is velocity sensitive. Usually this means that the harder you hit the keys, the
louder the sound that is produced. However this ultimately depends on how the instrument youre controlling is
programmed and your playing style.
In order to match the style of individual users, iRig KEYS 37 PRO offers six different velocity response settings:
0. FIXED, 64. This setting will always send a fixed MIDI velocity value of 64 without any touch response.
1. FIXED, 100. This setting will always send a fixed MIDI velocity value of 100 without any touch response.
2. FIXED, 127. This setting will always send a fixed MIDI velocity value of 127 without any touch response.
3. VEL SENS, LIGHT. Use this setting if you prefer a light touch on the keys. This is especially useful when you
need to play fast passages or program drum patterns.
4. VEL SENS, NORMAL. This setting is the default setting and works well in most cases.
5. VEL SENS, HEAVY. Use this setting if you prefer a heavy touch on the keys.
To set the velocity response:
English
Press the F#2 key (VEL), both OCT buttons will flash.
Enter your velocity response selection by using the C3-A3 white keys marked from 0 to 5.
Press the C5 key (ENTER/YES) to confirm your input. Both PROG buttons will flash to show the setting has
been accepted, and iRig KEYS 37 PRO will automatically exit EDIT mode.
By default, the VOL/DATA knob sends MIDI Volume messages which are assigned to MIDI Controller #7.
However, you can customize the MIDI Controller number that is associated with the VOL/DATA knob.
To assign a Controller number to the KNOB:
Press the G#2 key (KNOB), both OCT buttons will flash.
Enter the MIDI CC number you need using the C3-E4 white keys marked from 0 to 9. Valid numbers are
from 0 to 127, so you can enter up to three digits consecutively when needed.
Press the C5 key (ENTER/YES) to confirm your input. Both PROG buttons will flash to show the setting has
been accepted, and iRig KEYS 37 PRO will automatically exit EDIT mode.
Send specific MIDI Program Changes numbers, and set Current Program number
iRig KEYS 37 PRO can send MIDI Program Changes in two ways:
1. Program Changes are sent sequentially by using the PROG up and PROG down buttons 7 .
2. Program Changes are sent directly by sending a specific Program Change number from within EDIT mode.
After sending a specific Program Change number, the PROG up and down buttons will work sequentially
from that point.
To send a specific Program Change number:
Press the A#2 key (PROG), both OCT buttons will start flashing.
Enter the Program Change number using the C3-E4 white keys marked from 0 to 9. Valid numbers are from
1 to 128, so you can enter up to three digits consecutively when needed.
Press the C5 key (ENTER/YES) to confirm your input. Both PROG buttons will flash to show the setting has
been accepted, and iRig KEYS 37 PRO will automatically exit EDIT mode.
9
English
Send All Notes Off MIDI message
Sometimes it may be necessary to stop all notes playing on the current MIDI channel when they are stuck or
when controllers are not resetting properly.
iRig KEYS 37 PRO can send MIDI CC# 121 + 123 to reset all controllers and stop all notes.
To reset all controllers and set all notes off:
Both PROG buttons will flash to show the reset has been sent, and iRig KEYS 37 PRO will automatically exit
EDIT mode.
The iRig KEYS 37 PRO keyboard can be transposed in semitones. This can be useful when, for example, you
need to play a song that is in a difficult key, but you still want to physically play it in an easier or more familiar
key.
To transpose iRig KEYS 37 PRO:
Press the G#4 key (TRANSP), both OCT buttons will start flashing.
Press any note on the keyboard: from this moment on, when you press a C key, iRig KEYS 37 PRO will
actually sent the MIDI note you pressed at this step.
Both PROG buttons will flash to show the semitone transpose has been set, and iRig KEYS 37 PRO will
automatically exit EDIT mode.
Example
If you need to play a song that has been recorded in key of D#, but you would like to play it on the keyboard as
if it was in C, do the following:
From this moment on when you press a C key on the keyboard, iRig KEYS 37 PRO will actually send a D# MIDI
note. All other notes are transposed by the same amount.
10
English
Reset iRig KEYS 37 PRO
iRig KEYS 37 PRO can be reset to its original factory state. This can be done independently for each one of the
SETs or for the normal no-SET mode.
To reset iRig KEYS 37 PRO or a SET:
Load the SET you would like to reset, or to not load any SET, you can reset the normal no-SET mode.
Both PROG buttons will flash to show the SET has been reset, and iRig KEYS 37 PRO will automatically exit
EDIT mode.
SETs
iRig KEYS 37 PRO offers many options to satisfy the most demanding user. However, when the keyboard is
used live or to control many different instruments, it could be time consuming and tricky to manually set all the
parameters you need each time.
For this reason, iRig KEYS 37 PRO has 4 user configurable presets that can be recalled on the fly by pressing
just one button, these are called SETs.
-> NO SET -> SET 1 -> SET 2 -> SET 3 -> SET 4 -> NO SET
English
seconds. The current SET LED will flash to confirm that the SET has been saved. Remember to always save a
SET if you have made modifications to it that you would like to keep.
When no SET is loaded, iRig KEYS 37 PRO automatically uses the previous settings that were made before
loading a SET.
Troubleshooting
iRig KEYS 37 PRO doesnt play my instrument even if though it is turned ON.
Make sure the MIDI Transmit Channel matches the receiving MIDI channel of your instrument. See the
paragraph Set MIDI Transmit Channel.
iRig KEYS 37 PRO suddenly appears to have different settings from those I used.
You have probably loaded a SET. If you dont want to use a SET, press the SET button repeatedly until all SET
LEDs are off.
Warranty
Please visit:
www.ikmultimedia.com/warranty
for the complete warranty policy.
12
Regulatory
B
( )
Class B Equipment
(For Home Use Broadcasting & Communication Equipment)
(B )
, .
IK Multimedia
IK Multimedia Production Srl
Via dellIndustria 46, 41122 Modena, Italy
Phone: +39-059-285496 - Fax: +39-059-2861671
IK Multimedia US LLC
1153 Sawgrass Corporate Parkway, Sunrise, FL 33323
Phone: 954-846-9101 - Fax: 954-846-9077
IK Multimedia Asia
TB Tamachi Bldg. 1F, MBE #709,
4-11-1 Shiba, Minato-ku, Tokyo 108-0014
www.ikmultimedia.com/contact-us
iRig KEYS 37 PRO, iGrand Piano and SampleTank are trademarks property of IK Multimedia Production Srl. All other product names and images, trademarks and artists names are the property of
their respective owners, which are in no way associated or affiliated with IK Multimedia. iPad, iPhone, iPod touch Mac and Mac logo are trademarks of Apple Computer, Inc., registered in the U.S. and
other countries. Lightning is a trademark of Apple Inc. App Store is a service mark of Apple Inc.
2015/10/19
13