Beruflich Dokumente
Kultur Dokumente
HOME
FREE DOWNLOAD
FREE DOWNLOAD
Search
ABOUT
Today i will show how to make PCB at home . PCB means Printed Circuit Board . Would
you like to know more about PCB? , please follow the link Wikipedia .
POPULAR POSTS
ALL POSTS
POPULAR POSTS
Matrix [4x4] Keypad interfacing
with PIC Microcontroller [
PIC18f2550 ] in Proteus [Step
by Step]
Matrix Keypad interfacing with
PIC Microcontroller [ PIC18f2550 ] in
Proteus [Step by Step] Basically a matrix
keypad[ 4x4] can be c...
Bipolar Stepper Motor
Interfacing With PIC
Microcontroller (PIC18F2550)
in Proteus [step by step]
Stepper Motor (animation source :
wikipedia) Stepper Motors and It's Working
Princ...
We will need
1.Ferric Chloride
2. Copper Board
3. Glossy Paper .
4. Iron
5. Drill Bit [ Small ]
6. Paint Thinner
7. Hand Gloves
Step 1:
Open the PCB diagram with Foxit reader or Adobe reader . It doesn't matter what you
are using , just make sure that you are printing it with 100% (Actual) size . It is
recommended , the printer should be Laser printer . If you don't have Laser printer don't
worry , i have a solution . First print out the circuit diagram on a normal paper in 100%
size . Now make a photo copy of the diagram with glossy paper by photostat machine .
Because both of Laser printer and Photostat machine have same type ink .
ALL POSTS
15 (15)
Note : We are getting the circuit diagram on a glossy paper .
After printing the circuit will look like that :
Jul (5)
Jun (2)
Microcontroller Project : Digital Voting
Machine u...
How to make PCB (Printed Circuit Board) at
Home [s...
Jan (8)
14 (7)
TAGS
pic18f2550
(14)
microcontroller (11) using
(11) How to (9) step by step (9)
interface (8) pic microcontroller (7)
proteus (7) Microcontroller Project (6)
Step 2:
Buy a copper board and cut it with required dimension . If you are in Bangladesh , you
can visit http://toolsbd.com to collect necessary parts . A little rubbing is required to
make clean the copper board . Look at the picture :
(1) Serial
communication
(1) Servo
Motor
(1)
GOOGLE+ FOLLOWERS
Your email
Address...
Your
email
Address...
Subscribe
Now using Masking Tape, add PCB Diagram with Copper Board carefully .
Microcontroller T
52 likes
Like Page
Share
This picture of masking is collected from techtunes.com.bd .Some how i missed this step to capture
We need to provide hit on this and we should use an Iron . Be careful , you don't need to
provide very high temperature . At rst keep it on copper board so that hit can spread .
After 2or3 min , start ironing smoothly . Keep in mind that rough ironing will damage the
copper board .
After heating 7or 8 min . Wash it with water carefully and keep it there for 20 min .
Now remove the paper carefully and carefully wash it by water .It will look like this
Step 3:
Bring a pot with water and provide some Ferric Chloride on that . Be careful you should
provide
Ferric Chloride on water . Don't watering on Ferric Chloride . Now sink the copper board
and moves the water pot slowly for 20 min . You will see that copper will be being
vanished .
This picture is collected from techtunes.com.bd .Some how i missed this step to
capture .
After this step complete wash the board with soap and use paint thinner to clear and
remove ink from the board .
Now , we need to drill the board . If you have drill machine and it will be ne . If you
don't have drill machine , don't worry .
You can follow my method using drill bit . I didn't buy any drill machine !!!
Thank You !!
Good (0)
Reactions:
Bad (0)
Best (0)
? Facebook
Newer
Post
? Google+ Home
? Stumble
? Digg
Older Post
Related Posts Widget
0 comments:
Post a Comment