Beruflich Dokumente
Kultur Dokumente
CURRICULUM VITAE
Mobile No.
+966553043236(Saudi Arabia)
Email Id
ENGR.
alam_sajid@yahoo.co.uk
PROFILE:--Proficient
PROFESSIONAL QUALIFICATION
INSPECTION
&
Q.A.
COMPANY
Knowledge
and
familiar
with
International
Codes/Standards & with major clients specifications:
API
5L, API 570, API 1104, DIN 30760, CSAZ 245.21
API 653, API 510, API 650, ASME B 16.20, ASME B16.21, ASTM D 2584
ASME Sec. IX/AWS D1.1, ASTM A153, ASTM D0638, ASTM D 2290
ASME Sec V, ASME Sec. VIII and with Major Clients Specifications.
ASME B 31.4, 31.4 & AWWA & Other Various technical code and standards.
Project Performed/Inspected/Monitored & Attainted: -----1. Shuqaiq Phase II Water Transmission System SWCC Saudi Arabia
2 KFIP Petrol Oil/Gas Pipe Line Corridor in Port Area JubailFor Royal
Commission Jubail.
3. Estern Province Water Transmission System---SWCC-Saudi Arbia
4. Ras Az Zawr/ Ras Al khair Water Transmission SystemSWCC/900KM
5. Ras Al khair Hafr Al batain Water Transmission SystemSWCC/600KM
6. Hili Pipe line Phase 3---MOWE (Ministry of water and Electricity)-Jeddah
7. SAAD (WASIYA) Pipe Line -NWC (National Water Company)-Riyadh-Saudi
Arabia.
8. Riyadh Strategic Water Supply SchemeNational Water Company (NWC)
Riyadh.
9. Buraidah Water transmission line Al-Harbi-Saudi Arabia
10. Extension of Phase-1 Water Supply to villages at Hail Project 160KM
Saudi Arabia
11. Riyadh New City Feeder Line SWCC-Saudi Arabia.
12. Yanbu Madina Water Transmission System Phase 3SWCC
13. Erection of steel structure work and for piping --Murdhar power plantIndia
Onsite worked for Clients & for Companies/Industries: -1. Al Babtain and Omega company Riyadh-Saudi Arabia
2. Al Shamarany Steel and Contracting establishment Dammam-Saudi
Arabia
3. King Fahad industrial postRoyal Commission Jubail Industrial City-Saudi
Arabia
4. Saline Water Conversion Corporation(SWCC)-Riyadh-Saudi Arabia
5. National Water Company(NWC)-Riyadh-Saudi arabia
6. Group Five Pipe Saudi Company-2ND Industrial City Dammam-Saudi
7. Zamil steel Industries 1ST industrial City-Dammam-Saudi Arabia
8. National Pipe Company LTD(NPC)-Dharan-Dammam-Saudi Arabia
9. Welspun Middle East Pipe LLC & Coating Company-2 ND Industrial CityDammam-Saudi
10. Saudi Steel Pipe Company (SSP)-2ND Industrial City-Dammam-Saudi
Arabia.
11. Ministry for Water and Electricity(MOWE)-Jeddah/Hail-Saudi Arabia
12. Kuwait Pipes Industries and Oil services company-KPOIS-Kuwait
13. Gannon Dunkerly Corporation Limited-Mumbai-India.
14. Arabian pipe coating Company(APCO)-Jubail-Industrial City
15. Raymond Saudi Arabia Ltd. For CMLJeddah-Saudi Arabia.
16.
17.
18.
19.
20.
21.
22.
Job Types Performed at related Factory/Industries: ----(1) Inspection of Transmission Tower Electricity Fabrication, Test and
Inspection Performed
during project work as per client specification, ITP and procedure.
(2) Inspection and PT test (Dye penetrant Test)/UT test of joints self-carried
out during
Erection/Installation of GAS And Petroleum Oil corridors, structures at
Royal Commission
Jubail Industrial City.
Major Responsibilities for Rotating & Static Equipment: ---Monitor of Precommissioning, commissioning, start-up and initially
maintenance of rotating
Equipment.
Inspection during Precommissioning and commissioning of rotating
equipment in Utility Plant
and waste water Treatment.
Carry out inspections on Exception Items (EI) as documented and sign off
a closed when
Activity is complete.
Inspection of Pumps, Compressors, motors/blowers/fans/Turbine and
prepare the quality
reports as per client requirements after satisfactory inspections.
Conduct Inspection of base plates prior to install or erection of equipment.
Conduct free alignment of generator & turbine shaft alignment.
Check for pipe stress prior to final alignment on centrifugal pump.
Check for pipe stress prior to final alignment on centrifugal pump.
Conduct final inspection of generator & turbine shaft alignment with the
client.
Check / review vendor documents, P & IDs, PEFS, ISO drawing, technical
specification.
Prepared documents for all mechanical rotating equipment such as
equipment installation,
receiving, pre and final alignment of pumps, compressors and piping lines
connected to the
Equipment, sump pits inspection on pumps, etc. as per project plan and
ITP procedure.
Check/inspect the alignment, elevation
levelness of the installed stationary & rotating
Equipment & ensure the deficiencies are within acceptable limit
Check the installation of air fan coolers such as; fixing of plenum,
tightening, angle of fan,
blades motor installation, shafting, shaft sleeve, bearings, fly wheel,
bracing, top cover
Pulley and belt installation.
Erection of rotary equipment such as; Pump skid gear box, motor, compressor
and water injection
Pumps.
Competent and able to interpret/review the drawings.
Major Responsibilities performing for Painting & Coating:Responsible for stage wise internal painting / coating inspection of
incoming materials.
To check and monitor all painting / coating related works and ensure all
final products meet
In accordance with company procedure, client requirement and
international codes.
Prepare all necessary QA / QC coating documents and handed over to
clients review.
To undertake test qualifications for spray painters, brush painters hydro
blasters & abrasive
Blasters.
Responsible for incoming coating / painting material inspection and has to
ensure whether
These materials suits to meets the requirements of project specifications
Inspection of 3-layer high-density polyethylene coating on steel pipe.
Holiday inspection /monitor of coated pipes at site during process.
Monitor weather condition for surface preparation and coating application
at site.
Prepare the data sheet of coated pipes on site after internal inspection.
Review and analysis of all reports of mechanical and chemical tests related
to bare pipe and 3
Layer Polyethylene coated/FBE coated pipes after receiving on site and
prepare suitable
Notes/remarks and submit to client/technical manager/qc department
Checked Climate condition like weathers/temp before start blasting of
pipes.
Checked process preheat before blasting.
Checked residual surface chloride before and after blasting.
Checked Ph of acid wash Ph of acid on pipe, Ph of rinse/storage water on
pipe.
Exp. For inspection of FBE, 3LPE and 3LPP in vender manufacturer pipe and
for Pipe coating,
Field joint coating, heat shrinkage sleeve, Viscos elastic coating System
wrapping for
Underground.
Responsibilities performing for quality and safety:Follow and maintain Company standards of Quality in accordance with
Company Quality
System requirements.
Personal Information:
Date of Birth
:
Nationality
:
Marital Status
Passport. No.
Passport Expiry date
Saudi Iqama Status
Valid Saudi DL
Extra Information:
I am willing to travel anywhere.
Currently working but always looking.