Beruflich Dokumente
Kultur Dokumente
User Manual
FCR200xx
Fast Ethernet Fibre Optic
Media Converter with
Advanced LFP
Version 1.1
January 2010
Touch the metal chassis of your computer to ground the static electrical charge before
you handle the switch.
Pick up the switch by holding it on the left and right edges only.
EN55022(1988)/CISPR-22(1985)
EN60555-2(1995)
EN60555-3
IEC1000-4-2(1995)
IEC1000-4-3(1995)
IEC1000-4-4(1995)
class A
class A
4K V CD, 8KV, AD
3V/m
1KV (power line), 0.5KV (signal line)
1. Introduction
The FCR200xx series of Fast Ethernet media converters is IEEE802.3u compliant and supports
100Base-TX 100Mb Copper to 100Base-FX 100Mb Fibre. The FCR200xx can be used as a
standalone unit or as a slide-in module for the DCR12xx 19" converter rack (up to 12 units)
for use at a central wiring closet.
2. Model Description
Model
TPST/SC AC-DC +5V
TPST/SC USB +5V
Power Description
By AC-DC Adapter
By Self Powering Cable(USB)
Wavelength
1310nm
1310nm
1550nm
TX, RX Wavelength
3. Checklist
Before you start installing your equipment, verify that the package contains the following:
Please notify your supplier immediately if any of the aforementioned items are missing or
damaged.
4. Installation
Note:
TP Port
Default: AUTO
AUTO or FORCE setting, see Fig. 13 S1Bit 1
Attach TP Cat. 5 or higher grade cable to TP port, max. distance of 100m.
10/100 TP port supports AUTO MDI-X sensing.
Fibre Port
Default: 100FDX
"100FDX"/"100HDX" setting, see Fig. 13 S1Bit 5
100FX
Fibre
Network
R
TX
TX
RX
TP-to-100FX
Converter
10/100Base-TX
Network
TX
FX TP
RX
LNK
/ACT
100
FDX
/COL
PWR
FDX
LFP
10
HDX
LFP DIS
FDX
100
AUTO
S1
HDX-FX
FORCE
TP
5VDC
USB
Slide Switch
Fig. 6-1
5VDC
USB
Slide Switch
Fig. 6-2
TX, RX Wavelength
TX (Transmit) 1310nm
RX (Receive)
1550nm
TX (Transmit) 1550nm
RX (Receive)
1310nm
Note:
The 1310nm and 1550nm models must be installed in pairs, i.e., install 1310nm model at
one end and 1550nm model at the other one.
FX TP
TP
LNK
/ACT
100
FDX
/COL
Bridge Media Converter
10/100Base-TX to 100Base-FX
Single Fiber
PWR
7. LED Description
LED
Colour
FX LNK/ACT
Green
FX
FDX/COL
Amber
TP LNK/ACT
Green
TP 100
Green
PWR
Green
Function
Lit when fibre connection is good
Blinks when fibre data is present
Lit when full-duplex mode is active
Off when half-duplex is active
Blinks when collision is present
Lit when TP connection is good
Blinks when TP data is present
Lit when TP speed is 100Mbps
Off when TP speed is 10Mbps
Lit when +5V power is coming up
DC Jack:
2.5mm
DC Input:
+5V
(Converter DC Current Consumption: 2A
when operation at full load)
9. Dip Switches
:
:
:
:
AUTO(default) or FORCE
100 or 10 when TP at Force
FDX or HDX when TP at Force
LFP enabled(default) or disabled
100FDX(default) or 100HDX
Note:
1. S1-2 and S1-3 will take effect only when S1-1 is set at TP-FORCE.
Standards:
UTP Cable:
Fibre Cable:
LED Indicators:
Forwarding Rate
148,800 PPS
14,880 PPS
Flow Control:
Power Requirement:
Ambient Temperature:
Humidity:
Dimensions:
0 to 50C
5% to 90%
26.2(H) 70.3(W) 94(D) mm